Study of the CO2 decomposition over doped Ni-ferrites

The H₂ reduced NiFe_2−xCr_xO₄ can be used to decompose CO₂ to C repeatedly. A series of nanocrystalline Ni-ferrite doping different contents of Cr³⁺ were synthesized by mixed ions co-precipitation method and characterized by XRD, BET and TEM. The results showed that their crystallite sizes were 1-2 nm and BET surface area changed from 220 to 285 m²/g. The evaluation of the activity and stability indicated that Ni-ferrite with 4 wt% Cr³⁺ dopant could be used repeatedly as many as 60 times and was transformed to Fe_yNi_1−y (0<y<1) alloy and Fe₅C₂ gradually during the cycle decomposition of CO₂ to carbon, especially for no Cr³⁺ sample. After the 60th reaction, although NiFe₂O₄ phase just remained 2.1 wt%, the decomposition activity of Ni-ferrite with 4 wt% Cr³⁺ was still 60% of initial activity. This fact suggests that nanocrystalline Fe_yNi_1−y (0<y<1) alloy from the cycle reaction can contribute to the decomposition of CO₂. The results from scanning electron microscopy (SEM), TEM and XRD show that the deposited carbon from CO₂ decomposition consisted of amorphous, crystallite and carbon nanotubes.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Green and red up-conversion emissions of Er-Yb-codoped Al2O3 powders prepared by the nonaqueous sol-gel method

The 1 mol% Er³⁺- and 0-20 mol% Yb³⁺-codoped Al₂O₃ powders have been prepared by the nonaqueous sol-gel process using aluminum isopropoxide as precursor, acetylacetone as chelating agent, nitric acid as catalyzer, and hydrated erbium and ytterbium nitrate as dopant under isopropanol environment. The two crystalline types of doped Al₂O₃, γ and θ, and a stoichiometric compound, (Yb,Er)₃Al₅O₁₂, were obtained for all the Er³⁺-Yb³⁺-codoped Al₂O₃ powders at the sintering temperature of 1000 °C. The maximal intensity of both the green and red up-conversion emissions centered at about 523, 545, and 660 nm was observed for the 1 mol% Er³⁺- and 10 mol% Yb³⁺-codoped Al₂O₃ powders. The intensity ratio of the red to green up-conversion emission (I_red/I_green) increased with increasing the Yb³⁺ doping concentration for the Er³⁺-Yb³⁺-codoped Al₂O₃ powders. Furthermore, the intensity ratio of the green up-conversion emission at about 523 to 545 nm (I₅₂₃/I₅₄₅) was proportional to the Yb³⁺ doping concentration and pump electric current, which was associated with the elevated temperature of powders.     

Structural and luminescence characterization of synthetic Cr-doped Ni3(PO4)2

Ni_3–xCr_2x/3(PO₄)₂ (x=0 and 0.02) microcrystalline powders were obtained as single phases via a modified sol–gel Pechini-type in situ polymerizable complex method. The samples were characterized using scanning electron microscopy, X-ray diffraction, cathodoluminescence (CL), and thermoluminescence (TL) techniques. We found that Cr³⁺ doping modified the average particle and distribution. The mean particle size was 0.441 μm for Ni₃(PO₄)₂ and 0.267 μm for Ni_2.98Cr_0.013(PO₄)₂. The results also reveal that Cr³⁺ doping notably enhanced the CL and TL UV-blue emission.     

Magnetic properties of cobalt substituted M-type barium hexaferrite prepared by co-precipitation

The co-precipitation and solid state methods were used in the synthesis of barium hexaferrite (BaM). Phase pure BaM was obtained with 1, 2, 3, 5, 10, 15, 20 and 30 wt% cobalt oxide (Co₃O₄). The addition of Co^2+/3+ ions to the BaM increased the permeability and magnetic loss tangent to a value of 3.5 at 5% and reduced to 1 at 30% doping. With increased Co doping, M_s was reduced from 87-58 emu/g, M_r increased from 11 to 40 emu/g with 3–5 wt% Co and 9 emu/g for 30% doping. H_c sharply increased from 540 to 2200 Oe with a reduction to 280 Oe at 10 K with increasing temperature to 300 K. T_c increased from 740 to 750 K for 30% Co doping. DTA–TGA studies of green body showed decarboxilation to occur at around 825 °C and the transformation of residual Co₃O₄ to Co₂O₃ at around 577 °C. The XRD data confirmed the Co ions substituting into Fe sites until a 10–15% doping level where the structure altered to W-type hexaferrite. The densities of the compounds varied with doping to a maximum of 4.45 g/cm³.     

Ionic conductivity and electrochemical stability of poly(methylmethacrylate)-poly(ethylene oxide) blend-ceramic fillers composites

The role of inorganic ceramic fillers namely nanosized Al₂O₃ (15-25 nm) and TiO₂ (10-14 nm) and ferroelectric filler SrBi₄Ti₄O₁₅ (SBT CIT) (0.5 μm) synthesized by citrate gel technique (CIT) on the ionic conductivity and electrochemical properties of polymer blend 15 wt% PMMA+PEO₈:LiClO₄+2 wt% EC/PC electrolytes were investigated. Enhancement in conductivity was obtained with a maximum of 0.72×10⁻⁵ S cm⁻¹ at 21 °C for 2 wt% of SrBi₄Ti₄O₁₅ (SBT CIT) composite polymer electrolyte. The lithium-ion transport number and the electrochemical stability of the composite polymer electrolytes at ambient temperature were analyzed. An enhancement in electrochemical stability was observed for polymer composites containing 2 wt% of SrBi₄Ti₄O₁₅ (SBT CIT) as fillers.     

Dopings in the transition-metal aluminides OsAl2 to obtain materials with high spin polarization: A first-principles study

The doping effects of 3d transition metals on the magnetic properties of Os_1 − xCr_xAl₂ are studied by first-principles calculations. The Os_1 − xCr_xAl₂ alloys have high spin-polarizations at the Fermi level with the Cr concentration in the range of 0.0<x?0.625. At higher Cr concentration, the ferromagnetic phase transforms into a ferrimagnetic metallic phase.     

Formation of alumina-ceria mixed oxide in model systems

Interaction of aluminium with cerium oxide was studied by photoelectron spectroscopy of Al/CeO₂(1 1 1) and CeO₂/Al(1 1 1) model systems. It was found in both cases that metallic aluminium was immediately oxidized, CeO₂ was partially reduced and a mixed oxide with cerium present as Ce³⁺ was formed. The compound is probably cerium aluminate CeAlO₃ mixed with Al₂O₃ or Ce₂O₃. In both cases the intermixing was limited by the diffusion of aluminium into ceria. The excess of deposited material above this limit formed AlO_x and CeO₂ overlayers on the top of the mixed oxide + aluminate/CeO₂ and mixed oxide + aluminate/Al films, respectively.     

Energy transfer among three luminescent centers in full-color emitting ZnGa2O4:Mn, Cr phosphors

The ZnGa₂O₄:Mn²⁺, Cr³⁺ phosphors show three colors; the blue band of 380 nm from the charge transfer between Ga-O, the green band of 505 nm from Mn²⁺ and the red band of 705 nm from Cr³⁺. As a variation of Mn²⁺ or Cr³⁺ concentrations in ZnGa₂O₄:Mn²⁺, Cr³⁺, the relative emission intensity can be tuned. This phenomenon is explained in terms of the energy transfer based on four factors: the spectral overlap between the energy donors (Ga-O) and the energy accepters of Mn²⁺ or Cr³⁺, the absorption cross section of the energy accepters, the distance between them, and the decay time of the energy donors. ZnGa₂O₄:0.0025Mn²⁺, 0.010Cr³⁺ shows the CIE coordinates of x=0.4014, y=0.3368, which is a pure white light. The single-phased full-color emitting ZnGa₂O₄:Mn²⁺, Cr³⁺ phosphors can be applied to illumination devices.     

Y3Al5O12 ceramic absorbers for the suppression of parasitic oscillation in high-power Nd:YAG lasers

The objective of this study was to identify a material suitable to absorb radiation at the wavelength of neodymium-doped Yttrium Aluminum Garnet (Y₃Al₅O₁₂:YAG), 1064 nm. M-(M= Sm³⁺, Co²⁺, Co³⁺, Cr³⁺, and Cr⁴⁺) doped highly transparent YAG ceramics were fabricated, and their absorption spectra were measured. Unlike Co²⁺ and Cr³⁺-doped ceramic samples, Co³⁺ and Cr⁴⁺ and Sm³⁺-doped:YAG ceramics were found to have significant absorption at 1064 nm. However, the Sm³⁺-doped YAG clearly emerged as the best candidate because it is also transparent at 808 nm, the pumping wavelength laser diode (LD), and also at most absorption bands used for flash-lamp pumping.     

Mossbauer, infrared and magnetic susceptibility studies of iron sodium borate glasses doped by sulphur

The affect of sulphur on the structural properties of iron sodium diborate glasses having the composition {(100−x)Na₂B₄O₇+xFe₂O₃}+yS, where x=0.05, 0.15 and 0.25 mol% and Y=0, 2.5 and 5 wt% was studied by infrared, Mossbauer spectroscopy and magnetic susceptibility measurements. It was found that, for samples having 5 mol% Fe₂O₃ and free from sulphur, the iron ions are present in both Fe²⁺ and Fe³⁺ states and also 92% of the total iron enters the glass network as a glass former. The ratio of Fe³⁺/Fe²⁺ increases with increasing the iron content for sulphur-free samples and others containing sulphur. This ratio also decreases with increasing the sulphur content. The magnetic susceptibility was found to decrease with increasing the sulphur content. Also, the increase of Fe₂O₃ content led to a less symmetrical environment of Fe³⁺ ions and vice versa for the Fe²⁺ environment.     

Influence of Eu doping content on photoluminescence of Gd2O3:Eu phosphors prepared by liquid-phase reaction method

Europium-doped cubic Gd₂O₃:Eu³⁺ nanoparticles containing various activator content in the range of 5-15 wt% were synthesized by a liquid-phase reaction method to investigate the influence of Eu³⁺ loading on the optical properties of phosphors by using XRD, TEM, BET, spectrometer and fluorometer. The size of Gd₂O₃:Eu³⁺ powders was in the range 21-41 nm. The phosphors showed an initial increase in luminescence and then a subsequent decrease with further doping (above 10 wt%). The decay time was reduced with increasing Eu loading; however, it decreased significantly above the 10% Eu doping. From spectroscopic studies, the Eu³⁺ doping ion distribution was uniform and homogeneous up to the 10 wt% loading because no concentration quenching effect was observed. However, further Eu³⁺ doping above 10 wt% reduced the luminescence due to the concentration quenching effect, as deduced from the shortening of the decay time.     

Side-hole to anti-hole conversion in time-resolved spectral hole burning of ruby: Long-lived spectral holes due to ground state level population storage

We report time-resolved transient spectral hole burning of Verneuil-grown 20 ppm and ca. 0.6 ppm ruby (Al₂O₃:Cr³⁺) in zero field and low magnetic fields B∥c at 4 K. The hole-burning spectroscopy of the 20 ppm sample implies relatively rapid cross relaxation in the ⁴A₂ ground state on the ∼1 ms timescale both in zero field and in low magnetic fields, B∥c, up to 0.2 T. In the 0.6 ppm sample, side-hole to anti-hole conversion is observed both in zero field and in low magnetic fields. This conversion is caused by population storage in ⁴A₂ ground state levels. Spin-lattice relaxation, on the 200 ms timescale, is directly observed from the time dependence of the resonant hole and anti holes in B∥c, consistent with a very low cross-relaxation rate. However, in zero field cross relaxation in the ⁴A₂ ground state is still a significant relaxation mechanism for the 0.6 ppm sample resulting in hole decay in ∼50 ms.     

Enhanced optical activation of Er in Er-doped Al2O3 powders by Y codoping in a sol-gel method

Enhanced photoluminescence (PL) mechanism of Er³⁺-doped Al₂O₃ powders by Y³⁺ codoping at wavelength 1.53 μm has been investigated through PL measurements of 0.1 mol% Er³⁺- and 0-20 mol% Y³⁺-codoped Al₂O₃ powders prepared at a sintering temperature of 900 °C in a non-aqueous sol-gel method. PL intensity and lifetime of Er³⁺-Y³⁺-codoped Al₂O₃ powders composed of γ-(Al,Er,Y)₂O₃ and θ-(Al,Er,Y)₂O₃ phases increased with increasing Y³⁺-codoping concentration. The 10-20 mol% Y³⁺ codoping in 0.1 mol% Er³⁺-doped Al₂O₃ powders intensified the PL intensity by about 20 times, with a PL lifetime prolonged from 3.5 to 5.8 ms. A maximal increase of the optical activity of Er³⁺ in 0.1 mol% Er³⁺-Y³⁺-codoped Al₂O₃ powders about one order was achieved by 10-20 mol% Y³⁺ codoping. It is found that the improved PL properties for Er³⁺-Y³⁺-codoped Al₂O₃ powders are mainly attributed to enhanced optical activation of Er³⁺ in the Al₂O₃ by Y³⁺ codoping, and to the slightly increased radiative quantum efficiency of Er³⁺ in the Al₂O₃.     

Effect of Al2O3 on the electrical properties of ZnO-Pr6O11-based varistor ceramics

The effect of Al₂O₃ on the electrical properties of ZnO-Pr₆O₁₁-based ceramics is investigated in this work. The average grain size of ZnO increased as the Al₂O₃ content increased from 10.3 to 13.5 μm. It was found that a sample doped with Al₂O₃ of 0.005 mol% showed the highest nonlinear current-voltage characteristics with a nonlinear exponent of 43.8 and a leakage current of 0.66 μA. When the Al₂O₃ content was increased, the donor concentration was increased from 0.51×10¹⁸/cm³ to 1.59×10¹⁸/cm³, but the barrier height was decreased from 1.01 to 0.87 eV. The best electrical stability against aging stress was obtained by doping Al₂O₃ of 0.001 mol%.     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

Electron energy loss spectra from polycrystalline Cr and Cr2O3 before and after surface reduction by Ar bombardment

Electron energy loss spectra (ELS) have been obtained from polycrystalline Cr and Cr₂O₃ before and after surface reduction by 2 keV Ar⁺ bombardment. The primary electron energy used in the ELS measurements was systematically varied from 100 to 1150 eV in order to distinguish surface versus bulk loss processes. Two predominant loss features in the ELS spectra obtained from Cr metal at 9.0 and 23.0 eV are assigned to the surface and bulk plasmon excitations, respectively, and a number of other features arising from single electron transitions from both the bulk and surface Cr 3d bands to higher-lying states in the conduction band are also present. The ELS spectra obtained from Cr₂O₃ exhibit features that originate from both interband transitions and charge-transfer transitions between the Cr and O ions as well as the bulk plasmon at 24.4 eV. The ELS feature at 4.0 eV arises from a charge-transfer transition between the oxygen and chromium ions in the two surface layers beneath the chemisorbed oxygen layer, and the ELS feature at 9.8 eV arises from a similar transition involving the chemisorbed oxygen atoms. The intensity of the ELS peak at 9.8 eV decreases after Ar⁺ sputtering due to the removal of chemisorbed oxygen atoms. Sputtering also increases the number of Cr²⁺ states on the surface, which in turn increases the intensity of the 4.0 eV feature. Furthermore, the ELS spectra obtained from the sputtered Cr₂O₃ surface exhibit features characteristic of both Cr⁰ and Cr₂O₃, indicating that Ar⁺ sputtering reduces Cr₂O₃. The fact that neither the surface- nor the bulk-plasmon features of Cr⁰ can be observed in the ELS spectra obtained from sputtered Cr₂O₃ while the loss features due to Cr⁰ interband transitions are clearly present indicates that Cr⁰ atoms form small clusters lacking a bulk metallic nature during Ar⁺ bombardment of Cr₂O₃.     

Effect of boric acid on structure,morphology and luminescent properties of divalent europium doped calcium aluminate phosphors

Blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ were prepared by high temperature solid-state method. Their structure, morphology and luminescent properties were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM) and fluorescence spectroscopy. The effect of different amounts of fluxing agent H₃BO₃ on structure, morphology and luminescent properties of blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ luminous intensity caused by different amount of H₃BO₃ was also investigated. The amount of H₃BO₃ doped Ca_1 − xAl₂O₄: xEu²⁺ in optimal luminous intensity had been determined. The results showed that both the excitation and emission spectra of samples were all broad bands, and that the peak of emission spectra was near 442 nm, which was corresponding to the 4f⁶5d → 4f⁷ transition of Eu²⁺ illuminating blue light. Ca_1 − xAl₂O₄: xEu²⁺ (x = 3.5 mol%) could be gained with good morphology and the best luminous intensity when H₃BO₃ mass ratio was 0.5 wt%.     

Room temperature stable structures and phase transition of Na2Al2B2O7

By Rietveld refinement of the X-ray diffraction (XRD) data of powdered Na₂Al₂B₂O₇ samples aged for over 3 months, we found that Na₂Al₂B₂O₇ at room temperature is a mixture of two phases with space group and P6₃/m, respectively. The structures of the two phases can be refined with identical cell parameters of a=4.80760(11) Å, c=15.2684(5) Å and are composed by [Al₂B₂O₇]²⁻_∝ double layers stacking alternatively with Na⁺ ions along the c-direction, but differ at in-plane bond orientations of the BO₃/AlO₄ groups within the double layers: in P6₃/m phase B-O₁/Al-O₁ bonds of the two layers are perfectly aligned, whereas in phase they are twisted by 46.4/41.6° around c-axis against each other. It is also found that a freshly prepared sample contains only the phase, but part of the phase will transfer to P6₃/m phase slowly at room temperature and the transition can be reversed by heating the aged sample above 220 °C.     

The morphology and optical properties of Cr-doped ZnO films grown using the magnetron co-sputtering method

Undoped ZnO and Zn_0.9Cr_0.1O films were prepared on Al₂O₃ (0 0 0 1) substrates using the magnetron co-sputtering technique. X-ray diffraction scans show that all films exhibit nearly single-phase wurtzite structure with c-axis orientation. Both chromium doping and growth ambient have a significant impact on the lattice constants and nucleation processes in ZnO film. A large quantity of subgrains (10 nm in size) has been observed on Zn_0.9Cr_0.1O film grown under Ar + O₂, while irregular plateau-like grains 40-50 nm in size were observed on Zn_0.9Cr_0.1O film grown under Ar + N₂. The ultraviolet-visible transmittance and optical bandgap of all films were also examined. The photoluminescence spectra of all films exhibit a broad emission located around 400 nm, which is composed of one weak ultraviolet luminescence and another rather intense near-violet one, as determined by Gaussian peak fitting. The near-violet emission centered on 400 nm might originate from the electron transition between the band tail state levels of surface defects and/or lattice imperfection in the ZnO film.