A Lead‐Selective Membrane Electrode Based Upon a Phosphorylated Hexahomotrioxacalix[3]Arene

Solvent extraction of a mixture of Pb^II, Mn^II, Fe^III, Co^II, Ni^II and Cd^II in aqueous perchlorate medium by a phosphorylated hexahomotrioxacalix[3]arene (calix‐3) in dichloromethane shows a significant selectivity towards lead ions. The ligand can also be incorporated into a membrane to provide a new lead ion‐selective electrode (Pb^II‐ISE). A plasticized PVC membrane containing 30% PVC, 53.5% ortho‐nitrophenyloctylether (NPOE), 4.5% sodium tetraphenylborate (NaTPB) and 12% ionophore was directly coated on a graphite rod. This sensor gave a good Nernstian response of 29.7 ± 0.7 mV decade^?1 over a concentration range of 1 × 10^?8 – 1 × 10^?4 M of lead ions, independent of pH in the range 3‐7, with a detection limit of 0.4 × 10^?8 M. The dynamic response time of the electrode to achieve a steady potential was very fast and found to be less than 7 s. The selectivity relative to Ag⁺, NH₄⁺, Li⁺, Na⁺, K⁺, Ca²⁺, Sr²⁺, Ba²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Fe³⁺, La³⁺, Sm³⁺, Dy³⁺, Er³⁺, Y³⁺ and Th⁴⁺ was examined. The electrode exhibits adequate stability with good reproducibility (with a slope of 29.6 ± 1.5 mV for 8 weeks). The characteristics of the sensor are compared with those of a tetraphosphorylated calix[4]arene (calix‐4) based Pb^II‐ISE, reported recently. The electrode was successfully used as an indicator electrode for a potentiometric titration of a lead solution using a standard solution of EDTA. The applicability of the sensor for lead ion measurements in various synthetic samples was also investigated.     

Capacitively coupled contactless conductivity detection with dual top–bottom cell configuration for microchip electrophoresis

An optimized capacitively coupled contactless conductivity detector for microchip electophoresis is presented. The detector consists of a pair of top–bottom excitation electrodes and a pair of pickup electrodes disposed onto a very thin plastic microfluidic chip. The detection cell formed by the electrodes is completely encased and shielded in a metal housing. These approaches allow for the enhancement of signal coupling and extraction from the detection cell that result in an improved signal‐to‐noise‐ratio and detection sensitivity. The improved detector performance is illustrated by the electrophoretic separation of six cations (NH, K⁺, Ca²⁺, Na⁺, Mg²⁺, Li⁺) with a detection limit of approximately 0.3 μM and the analysis of the anions (Br^?, Cl^?, NO, NO, SO, F^?) with a detection limit of about 0.15 μM. These LODs are significantly improved compared with previous reports using the conventional top–top electrode geometry. The developed system was applied to the analysis of ions in bottled drinking water samples.     

Reversible and Highly Selective Fluorescent Sensor for Mercury(II) Based on a Water‐Soluble Poly(para‐phenylene)s Containing Thymine and Sulfonate Moieties

A novel water‐soluble poly(para‐phenylene) derivative with pendant thymine and sulfonate units (PBTS) has been prepared and its metal ion sensing properties have been investigated. PBTS exhibited a reversible and selective fluorescence quenching behavior toward Hg²⁺ ions as compared to Ag⁺, Ni²⁺, Mg²⁺, Ca²⁺, Hg²⁺, Co²⁺, Cd²⁺, Cu²⁺, Pb²⁺, Ba²⁺, Fe³⁺, and Zn²⁺ ions in aqueous solution. The fluorescence quenching resulted from the interpolymeric π‐stacking aggregation which was induced by the specific thymine–Hg–thymine interaction.

     

Simultaneous Determination of Na+, K+, Ca2+, Mg2+ and Cl− in Unstimulated and Stimulated Human Saliva Using All Solid State Multisensor Platform

Human saliva is one of the body fluids which collection method is relatively simple and non‐invasive. The article is dedicated to assess concentration (activity) of Na⁺, K⁺, Ca²⁺, Mg²⁺ and Cl⁻ in fresh, unstimulated or stimulated human saliva samples using single solid contact ion‐selective electrodes with conventional reference electrode and self‐made multisensor platform (MP) equipped with ion‐selective membranes for Na⁺, K⁺, Ca²⁺, Mg²⁺ and Cl⁻ and reference electrode made in solid state technology, based on dispersed KCl in the polymer. Both kind of electrodes, single ISE and miniaturized electrodes in multisensor platform (ISE‐MP) were made of glassy carbon. The electrode surfaces have been modified by conductive polymer (PEDOT) layer deposition; with the exception of Cl⁻ electrode, in which conducting polymer was not applied. Potentiometric measurements were used to compare the changes of the ionic composition in various samples of saliva.     

A Bis‐Oxime Derivative of Diaza‐18‐Crown‐6 as an Ionophore for Silver Ion

A new pendant‐arm derivative of diaza‐18‐crown‐6, containing two oxime donor groups, has been synthesized and incorporated into a polyvinyl chloride (PVC) membrane ion‐selective electrode. The electrode shows selectivity for Ag⁺ ion, with a near Nernstian response. Pb²⁺, Cu²⁺, Hg²⁺, and Tl⁺ are major interfering ions, with Cd²⁺ having minor interference. The electrode shows no potentiometric response for the ions Mg²⁺, Al³⁺, K⁺, Ca²⁺, Ni²⁺, Fe³⁺, and La³⁺, and is responsive to H⁺ at pH<6.     

Cation-crown ether complex formation in water. II. Alkali and alkaline earth cations and 12-crown-4, 15-crown-5, and 18-crown-6

The stability constants and the partial molal volume and isentropic partial molal compressibility changes of complex formation between cations and crown ethers in water at 25°C are presented. The cations involved are Na⁺, K⁺, Rb⁺, Cs⁺, Ca²⁺, and Ba²⁺, and the crown ethers are 12-crown-4, 15-crown-5, and 18-crown-6. Values of V of complex formation have been discussed in terms of two simple models, one based on the scaled particle theory, and the others on the Drude-Nernst continuum model. The results indicate that the charge of the potassium cation in 18-crown-6 is especially well screened from the water. On this basis hydration numbers of complexed cations have been calculated. This shows that the size of the cation compared to the crown ether hole is important for the contacts between complexed cations and water.     

Evaluation of electrodes coated with metal hexacyanoferrate as amperometric sensors for nonelectroactive cations in flow systems

Two electrodes modified with either nickel or cupric hexacyanoferrate films were evaluated and compared as sensors for nonelectroactive cations in a flow-injection system. Both gave responses for group 1A and ammonium ions, but only the electrode modified with cupric hexacyanoferrate was sufficiently stable for use in flowing solutions. This electrode responded to K⁺, NH, Rb⁺, and Cs⁺ ions rather selectively. Within this group, the selectivity could be controlled from general to almost specific toward Cs⁺ by the potential at which the electrode was poised. The electrode was compatible with a mobile phase of dilute nitric acid commonly used in ion chromatography, and chromatographic detection limits of 2 × 10⁻⁷ M and linear responses over two decades were obtained. The electrode was applied to the ion chromatographic analysis of K⁺ and NH in urine and K⁺ in blood serum samples.     

Fourier transform infrared spectroscopy study of the effect of pH on anion and cation adsorption onto poly(acrylo‐amidino diethylenediamine)

The role of hydrogen bonding in the chemistry of transition‐metal complexes remains a topic of intense scientific and technological interest. Poly(acrylo‐amidino diethylenediamine) was synthesized to study the effects of hydrogen bonding on complexes at different pHs. The polymer was synthesized through the coupling of diethylene triamine with polyacrylonitrile fiber in the presence of AlCl₃ · 6H₂O addition. The adsorption capacity of this polymer was 11.4 mequiv/g. The ions used for the adsorption test were CrO, PO, Cu²⁺, Ni²⁺, Fe²⁺, and Ag⁺. All experiments were confirmed with Fourier transform infrared. In the study of anion adsorption, at low pHs, only ionic bonds existed, whereas at high pHs, no bonds existed. However, in the middle pH region, both ionic bonds and hydrogen bonds formed between poly(acrylo‐amidino diethylenediamine) and the chromate ion or phosphate ion. When poly(acrylo‐amidino diethylenediamine) and metal ions (Cu²⁺, Ni²⁺, Fe²⁺, and Ag⁺) formed complexes, a hydrogen‐bonding effect was not observed with Fourier transform infrared. The quantity of metal ions adsorbed onto poly(acrylo‐amidino diethylenediamine) followed the order Ag⁺ > Cu²⁺ > Fe²⁺ > Ni²⁺. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2010–2018, 2004     

An Investigation into the Suitability of Bismuth as an Alternative to Gold‐Amalgam as a Working Electrode for the In Situ Determination of Chemical Redox Species in the Natural Environment

The suitability of the bismuth film working electrode was investigated as an alternative to the gold‐amalgam electrode used in solid state microelectrodes for in situ voltammetric analysis of redox chemistry in the natural environment (e.g., lakes, oceans, sedimentary pore waters). Chemical redox species measurable with the Au‐amalgam include O₂, H₂S, S , S₂O , Fe²⁺, Fe³⁺, Mn²⁺, I^?. Bismuth was electrochemically deposited to form a solid film analogous to the Au‐amalgam on a polished gold disk electrode. The useable potential window of the Bi‐film was found to be narrower than that of the Au‐amalgam, precluding the detection of dissolved O₂, I^? and S₂O , whose redox potentials fall outside the Bi‐film's range. The Bi‐film was able to detect free H₂S/HS^? and total sulfide (AVS), but not Fe²⁺ or Mn²⁺. The Bi‐film was less sensitive to low levels of total sulfide (<10 μM) than the Au‐amalgam; however, the Bi‐film was able to accurately quantify very high concentrations of sulfide (at least 15 mM), with a linear response up to an order of magnitude higher than that of the Au‐amalgam. Thus the Bi‐film appears to have limited application as an alternative to the Au‐amalgam microelectrode for in situ analysis of redox species in natural waters.     

ABTS‐Multiwalled Carbon Nanotubes Nanocomposite/Bi Film Electrode for Sensitive Determination of Cd and Pb by Differential Pulse Stripping Voltammetry

A 2,2′‐azinobis (3‐ethylbenzothiazoline‐6‐sulfonate) diammonium salt (ABTS)‐multiwalled carbon nanotubes (MWCNTs) nanocomposite/Bi film modified glassy carbon (GC) electrode was constructed for the differential pulse stripping voltammetric determination of trace Pb²⁺ and Cd²⁺. This electrode was more sensitive than ABTS‐free Bi/GC and Bi/MWCNTs/GC electrodes. Linear responses were obtained in the range from 0.5 to 35 μg L^?1 for Cd²⁺ and 0.2 to 50 μg L^?1 Pb(II), with detection limits of 0.2 μg L^?1 for Cd²⁺ and 0.1 μg L^?1 for Pb²⁺, respectively. This sensor was applied to the simultaneous detection of Cd²⁺ and Pb²⁺ in water samples with satisfactory recovery.     

A New Fluorescent Chemosensor for Cu2+ Based on 1,2,3,4,5,6,7,8,9,10‐Decahydroacridine‐1,8‐dione Fluorophore

A new chemosensor for Cu²⁺ was synthesized based on 1,2,3,4,5,6,7,8,9,10‐decahydroacridine‐1,8‐dione dyes, which exhibited an obvious fluorescent selectivity to the sensing of Cu²⁺ ions over other cations, such as Na⁺, K⁺, Ca²⁺, Cd²⁺, Co²⁺, Hg²⁺, Mg²⁺, Mn²⁺, Ni²⁺, Zn²⁺, Ag⁺ and Pb²⁺. Moreover, it presented a fluorescent switch function when EDTA was added to the compound‐Cu²⁺ complex in examined systems.     

Silver(I)‐Selective PVC Membrane Potentiometric Sensor Based on a Recently Synthesized Calix[4]arene

A new PVC membrane potentiometric sensor for Ag(I) ion based on a recently synthesized calix[4]arene compound of 5,11,17,23‐tetra‐tert‐butyl‐25,27‐dihydroxy‐calix[4]arene‐thiacrown‐4 is developed. The electrode exhibits a Nernstian response for Ag(I) ions over a wide concentration range (1.0×10^?2?1.0×10^?6 M) with a slope of 53.8±1.6 mV per decade. It has a relatively fast response time (5–10 s) and can be used for at least 2 months without any considerable divergence in potentials. The proposed electrode shows high selectivity towards Ag⁺ ions over Pb²⁺, Cd²⁺, Co²⁺, Zn²⁺, Cu²⁺, Ni²⁺, Sr²⁺, Mg²⁺, Ca²⁺, Li⁺, K⁺, Na⁺, NH₄⁺ ions and can be used in a pH range of 2–6. Only interference of Hg²⁺ is found. It is successfully used as an indicator electrode in potentiometric titration of a mixture of chloride, bromide and iodide ions.     

Luminescence Properties of Ca2Ga2SiO7:RE Phosphors for UV White‐Light‐Emitting Diodes

A series of Eu²⁺‐, Ce³⁺‐, and Tb³⁺‐doped Ca₂Ga₂SiO₇ phosphors is synthesized by using a high‐temperature solid‐state reaction. The powder X‐ray diffraction and structure refinement data indicate that our prepared phosphors are single phased and the phosphor crystalizes in a tetrahedral system with the ${P\bar 42m}$ (113) space group. The Eu²⁺‐ and Ce³⁺‐doped phosphors both have broad excitation bands, which match well with the UV light‐emitting diodes chips. Under irradiation of λ=350 nm, Ca₂Ga₂SiO₇:Eu²⁺ and Ca₂Ga₂SiO₇:Ce³⁺, Li⁺ have green and blue emissions, respectively. Luminescence of Ca₂Ga₂SiO₇:Tb³⁺, Li⁺ phosphor varies with the different Tb³⁺ contents. The thermal stability and energy‐migration mechanism of Ca₂Ga₂SiO₇:Eu²⁺ are also studied. The investigation results indicate that the prepared Ca₂Ga₂SiO₇:Eu²⁺ and Ca₂Ga₂SiO₇:Ce³⁺, Li⁺ samples show potential as green and blue phosphors, respectively, for UV‐excited white‐light‐emitting diodes.     

Bienzyme-based visual and spectrophotometric aptamer assay for quantitation of nanomolar levels of mercury(II)

The article describes a bienzyme visual system for aptamer-based assay of Hg(II) at nanomolar levels. The detection scheme is based on the finding that Hg(II) ions captured by aptamer-functionalized magnetic beads are capable of inhibiting the enzymatic activity of uricase and thus affect the formation of H₂O₂ and the blue product, i.e., oxidized tetramethylbenzidine. This strategy allows for a visual detection of Hg(II) at nanomolar levels without additional amplification procedure. Measuring the absorbance at 650 nm, the logarithmic calibration plot is linear in the concentration range of 0.5–50 nM and the limit of detection (LOD) is 0.15 nM. This is as low as the LOD obtained by atomic fluorescence spectrometry (AFS). The ions K⁺, Mg²⁺, Na⁺, Ca²⁺, Cu²⁺, Zn²⁺, Fe³⁺, Al³⁺, Co²⁺, AsO₂ ^?, Ni²⁺, Cd²⁺ and Pb²⁺ do not have a significant effect on color formation. The method was applied to the analysis of (spiked) river water, lake water, mineral water, tap water and certified reference water samples, and the results agreed well with those obtained by AFS or certified values, with recoveries ranging from 97% to 109%. The relative standard deviation for five parallel detections at a 10 nM Hg(II) level is 5.2%.

Open image in new window

Graphical abstract A bienzyme-based visual aptasensor was fabricated for label-free detection of nanomolar Hg²⁺ in water samples without any amplification or enrichment procedure.

     

Bifunctional Ion‐Selective Electrode Based on C60‐Cryptand 22 for Silver and Iodine Ions

Fullerence C60‐cryptand 22 was prepared and successfully applied as the electric carrier in the PVC electrode membrane of a bifunctional ion‐selective electrode for cations, e.g., Ag⁺ ions as well as anions, e.g., I^? ions. The bifunctional ion‐selective electrode based on C60‐cryptand 22 can be applied as a Silver (Ag⁺) ion selective electrode with an internal electrode solution of 10^?3 M AgNO₃ in water (pH = 6.3), or as an Iodide (I^?) ion selective electrode with an acidic internal electrode solution of 10^?4 M KI_(aq) (pH = 2) in which the cryptand 22 is protonated, and the C60‐cryptand 22 is changed to C60‐Cryptand22–H⁺ and becomes an anionic electro‐carrier to absorb the I^? ion. The Ag⁺ ion selective electrode based on C60‐cryptand 22 gave a linear response with a near‐Nernstian slope (59.5 mV decade^?1) within the concentration range 10^?1‐10^?3 M Ag⁺_(aq). The Ag⁺ ion electrode exhibited comparatively good selectivity for silver ions, over other transition‐metal ions, alkali and alkaline earth metal ions. The Ag⁺ ion selective electrode with good stability and reproducibility was successfully used for the titration of Ag⁺_(aq) with Cl^? ions. The Iodide (I^?) Ion selective electrode based on protonated C60–cryptand22‐H⁺ also showed a linear response with a nearly Nernstian slope (58.5 mV decade^?1) within 10^?1 ‐ 10^?3 M I^? _(aq) and exhibited good selectivity for I^? ions and had small selectivity coefficients (10^?2–10^?3) for most of other anions, e.g., F^? , OH^?, CH₃COO^?, SO₄^2?, CO₃^2?, CrO₄^2?, Cr₂O₇^2? and PO₄^3? ions.     

pH-sensing properties of PbO<Subscript>2</Subscript> thin film electrodeposited on carbon ceramic electrode

In this paper, a new highly sensitive potentiometric pH electrode is proposed based on the solid-state PbO₂ film electrodeposited on carbon ceramic electrode (CCE). Two different crystal structures of PbO₂, α and β were examined and the similar results were obtained. Moreover, the experimental results obtained for the proposed pH sensor and a conventional glass pH electrode were in good agreement. The electromotive force (emf) signal between the pH-sensitive PbO₂-coated CCE and SCE reference electrode was linear over the pH range of 1.5–12.5. Near-Nernstian slopes of −64.82 and −57.85 mV/pH unit were obtained for α- and β-PbO₂ electrodes, respectively. The interferences of some mono-valence and multi-valence ions on potentiometric response of the sensor were studied. The proposed pH sensor displayed high ion selectivity with respect to K⁺, Na⁺, Ca²⁺, and Li⁺, with log values around −12 and has a working lifetime of about 30 days. Key parameters important for the pH sensor performance, including kind of PbO₂ film, selectivity, response time, stability, and reproducibility, have been characterized. The proposed electrode showed a good efficiency for direct pH-metry after calibration and pH-metric titrations without calibration step. The response time was about 1 s in acidic medium and less than 30 s in alkaline solutions. The pH values of complex matrix samples such as fruit juices measured by the proposed sensor and a conventional glass pH electrode were in good agreement.     

Single‐Piece Solid‐Contact Pb2+‐Selective Electrodes Based on Thiophene Oligomer

A single‐piece solid‐contact Pb²⁺‐selective electrode was prepared by adding a thiophene oligomer into the ion‐selective cocktail directly. The one‐step fabrication yielded an electrode with Nernstian response spanning a wide concentration range of 10^?3–10^?8 mol L^?1, and detection limit as low as 5.6×10^?9 mol L^?1. The electrode had a quick response time of approximately 10–15 s and showed excellent selectivity over the most common univalent and divalent cations. The practical application of the proposed electrode has been tested by determining Pb²⁺ in real water samples.     

Ionic liquids dispersive liquid–liquid microextraction and HPLC‐atomic fluorescence spectrometric determination of mercury species in environmental waters

An ionic liquid (IL) based dispersive liquid–liquid microextraction combined with HPLC hydride generation atomic fluorescence spectrometry method for the preconcentration and determination of mercury species in environmental water samples is described. Four mercury species (MeHg⁺, EtHg⁺, PhHg⁺, and Hg²⁺) were complexed with dithionate and the neutral chelates were extracted into IL drops using dispersive liquid–liquid microextraction. Variables affecting the formation and extraction of mercury dithizonates were optimized. The optimum conditions found were as follows: IL‐type and amount, 0.05 g of 1‐octyl‐3‐methylimidazolium hexafluorophosphate; dispersive solvents type and amount, 500 μL of acetone; pH, 6; extraction time, 2 min; centrifugation time, 12 min; and no sodium chloride addition. Under the optimized conditions, the detection limits of the analytes were 0.031 μg/L for Hg²⁺, 0.016 μg/L for MeHg⁺, 0.024 μg/L for EtHg⁺, and 0.092 μg/L for PhHg⁺, respectively. The repeatability of the method, expressed as RSD, was between 1.4 and 5.2% (n = 10), and the average recoveries for spiked test were 96.9% for Hg²⁺, 90.9% for MeHg⁺, 90.5% for EtHg⁺, 92.3% for PhHg⁺, respectively. The developed method was successfully applied for the speciation of mercury in environmental water samples.     

Automated SIA System Using an Array of Potentiometric Sensors for Determining Alkaline‐Earth Ions in Water

This work deals with the simultaneous determination of Mg²⁺, Ca²⁺, and Ba²⁺ in water using a PVC‐membrane potentiometric sensor array and multivariate calibration, in what is known as electronic tongue. The subsequent processing of the data was based on the use of a multilayer artificial neural network (ANN). The information needed for training or generation of the model was obtained with the aid of an automated analytical system based on the Sequential Injection Analysis (SIA) technique. The modeling ability was verified with an external set of standards, and next the determinations were performed in real samples of mineral waters, where close results for Mg²⁺ and Ca²⁺ were obtained to those obtained with reference methods. The determination of Ba²⁺ can be considered as semi‐quantitative for synthetic samples – due to the absence of Ba²⁺ in mineral waters, its concentration in real samples was not measured.