Carbon dendrite formation induced by pulsed laser irradiation

Porous carbon dendrite has been prepared by irradiating graphite targets with 532 nm, 10 ns laser pulses. The prepared samples were characterized by means of scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The measurement results show that carbon dendrite structures with cluster diameter of 10 nm were obtained on the irradiated target surface in an inert gas atmosphere. The evolution of target surface morphology induced by different laser intensities was investigated. The formation mechanism of the dendrite structure has been discussed in detail. The laser intensity plays an important role in the formation of the nanostructures and there exists an optimum intensity to prepare the carbon dendrite.     

Porous silicon as efficient surface enhanced Raman scattering (SERS) substrate

Silver nanocrystallites are obtained through immersion of porous silicon samples in AgNO₃ solutions and a successive thermal annealing. The efficiency of nanostructures as surface enhanced Raman scattering (SERS) substrates is checked on cyanine-based dyes and horseradish peroxidase, evidencing detectable concentrations as low as 10⁻⁷ to 10⁻⁸ M. The substrate efficiency is strictly related to the Ag particle morphology, which could yield to either local surface plasmons (LSP) coupled to individual particles or to inter-particle short-range interaction.     

Synthesis of silver nanowires via electroplating technology and its surface enhanced Raman scattering effect

This very paper is focusing on the preparation of silver nanostructures and the surface enhanced Raman scattering effect of the silver nanostructures produced. Via electroplating technology, silver nanowires and nanoparticles were prepared on silicon wafers. Characterization was performed by X-ray diffraction, scanning electron microscope, transmission electron microscope equipped with X-ray energy dispersion spectroscope and selected area electron diffraction, which reveals that the formation of silver nanostructures depends on the over-potential. The produced silver nanowires are of crystalline FCC structure and grow in 〈0 1 1〉 direction. The growth mechanism has been further discussed. The surface enhanced Raman scattering effect is achieved with the silver nanostructures produced.     

Surface-modification of anode carbon for lithium-ion battery using chemical vapor infiltration technique

To reduce the high irreversible capacity of the low crystalline carbon fiber for the anode material of lithium-ion battery, pyrolytic carbon (pyrocarbon) was coated at 950 °C from C₃H₈(30%)-H₂ gas system using pressure-pulsed chemical vapor infiltration. Carbon fiber was coated with the dense pyrocarbon film having the laminar texture and the low surface area of 1.9 m² g⁻¹. It was revealed from XRD and Raman spectroscopy that the crystallinity of pyrocarbon is higher than that of the core carbon. Electrochemical properties were measured in ethylene carbonate (EC) and propylene carbonate (PC) base electrolytes. Irreversible capacity was reduced in EC-based electrolyte by coating with 8 mass% pyrocarbon, which would be attributed to the high crystallinity, laminar structure and low surface area of pyrocarbon. Irreversible capacity was also decreased in PC-based electrolyte. The crystallinity of pyrocarbon was not so high as PC-based electrolyte was decomposed in the case of the high crystalline graphite.     

Effect of precursor preoxidation on the structure of phenolic resin-based activated carbon spheres

Activated carbon spheres with 3D hierarchical porous structure were prepared from phenol-formaldehyde resins with oxidation treatment in air and physical activation in an inert atmosphere. Based on the results of thermogravimetric analysis, infrared spectrometer (IR), scanning electron microscopy (SEM) and nitrogen adsorption/desorption, the effect of preoxidation on the morphology and structure of activated carbon spheres was investigated. The results show that decomposition and crosslinking reactions occur during the preoxidation and the structural changes of precursor generated by the preoxidation lead to differences in the pore structure of activated carbon spheres. The carbon spheres exhibit the unique 3D hierarchical porous structure, high specific surface area of 1897 m²/g and high pore volume of 2.22 cm³/g.     

Production and characterization of polymer nanocomposite with aligned single wall carbon nanotubes

We reported a simple method to fabricate polymer nanocomposites with single-walled carbon nanotubes (SWNTs) having exceptional alignment and improved mechanical properties. The composite films were fabricated by casting a suspension of single walled carbon nanotubes in a solution of thermoplastic polyurethane and tetrahydrofuran. The orientation as well as dispersion of nanotubes was determined by scanning electron microscopy, transmission electron microscopy and polarized Raman spectroscopy. The macroscopic alignment probably results from solvent-polymer interaction induced orientation of soft segment chain during swelling and moisture curing. The tensile behavior of the aligned nanotube composite film was also studied. At a 0.5 wt.% nanotube loading, a 1.9-fold increase in Young's modulus was achieved.     

Preparation and hydrogen storage of activated rayon-based carbon fibers with high specific surface area

Activated carbon fibers were prepared from rayon-based carbon fibers by two step activations with steam and KOH treatments. Hydrogen storage properties of the activated rayon-based carbon fibers with high specific surface area and micropore volume have been investigated. SEM, XRD and Brunauer-Emmett-Teller (BET) were used to characterize the samples. The adsorption performance and porous structure were investigated by nitrogen adsorption isotherm at 77 K on the base of BET and density functional theory (DFT). The BET specific surface area and micropore volume of the activated rayon-based carbon fibers were 3144 m²/g and 0.744 m³/g, respectively. Hydrogen storage properties of the samples were measured at 77 and 298 K with pressure-composition isotherm (PCT) measuring system based on the volumetric method. The capacities of hydrogen storage of the activated rayon-based carbon fibers were 7.01 and 1.46 wt% at 77 and 298 K at 4 MPa, respectively. Possible mechanisms for hydrogen storage in the activated rayon-based carbon fibers are discussed.     

Pyrolytic carbon derived from coffee shells as anode materials for lithium batteries

Disordered carbonaceous materials have been obtained by pyrolysis of coffee shells at 800 and 900 °C with pore-forming substances such as KOH and ZnCl₂. X-ray diffraction studies revealed a carbon structure with a large number of disorganized single layer carbon sheets. The structure and morphology of the materials have been greatly varied upon the addition of porogens. The prepared carbon materials have been subjected to cycling studies. The KOH-treated products offered higher capacity with improved stability than those with untreated and ZnCl₂-treated one.     

Field emission from patterned SnO2 nanostructures

A simple and reliable method has been developed for synthesizing finely patterned tin dioxide (SnO₂) nanostructure arrays on silicon substrates. A patterned Au catalyst film was prepared on the silicon wafer by radio frequency (RF) magnetron sputtering and photolithographic patterning processes. The patterned SnO₂ nanostructures arrays, a unit area is of ∼500 μm × 200 μm, were synthesized via vapor phase transport method. The surface morphology and composition of the as-synthesized SnO₂ nanostructures were characterized by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The mechanism of formation of SnO₂ nanostructures was also discussed. The measurement of field emission (FE) revealed that the as-synthesized SnO₂ nanorods, nanowires and nanoparticles arrays have a lower turn-on field of 2.6, 3.2 and 3.9 V/μm, respectively, at the current density of 0.1 μA/cm². This approach must have a wide variety of applications such as fabrications of micro-optical components and micropatterned oxide thin films used in FE-based flat panel displays, sensor arrays and so on.     

Hybrid nanostructured supports for surface enhanced Raman scattering

Porous silicon solid supports with pore diameter 0.5-1 μm, infiltrated with Ag nanostructures for surface enhanced Raman scattering (SERS) were prepared according to two procedures: spontaneous Ag⁺ reduction on the surface of freshly etched porous silicon immersed in Ag⁺ aqueous solutions, or anchoring colloidal Ag nanoparticles on the surface previously functionalized by aminosilane. Using Rhodamine 6G (RH6G) as analyte the detection limits were of the order of 20 μM and 20 nM with porous silicon metalized by the first and second procedure, respectively. This large increase of sensitivity notwithstanding a reduced surface density of Rhodamine 6G obtained on porous silicon metalized by the second procedure is discussed in terms of better hot spot efficiency and reduced aspecific binding out of the hot regions obtained depositing the colloids on the aminosilane functionalized surface.     

Monte Carlo simulation of hydrogen physisorption in K-doped single walled carbon nanotube array

Properties of hydrogen physisorption in K-doped single walled carbon nanotube array (SWCNTA) are investigated in detail by grand canonical Monte Carlo simulation. The optimization of hydrogen storage capacity at 293 K and 10 MPa as a function of K-doping schemes, K atoms’ doped-sites, and SWCNTA configuration is discussed.     

Nanoindentation on carbon thin films obtained from a C60 ion beam

Raman spectra, atomic force microscope (AFM) images, hardness (H) and Young's modulus (E) measurements were carried out in order to characterize carbon thin films obtained from a C₆₀ ion beam on silicon substrates at different deposition energies (from 100 up to 500 eV). The mechanical properties were studied via the nanoindentation technique. It has been observed by Raman spectroscopy and AFM that the microstructure presents significant changes for films deposited at energies close to 300 eV. However, these remarkable changes have not been noticeable on the mechanical properties: apparently H and E increase with higher deposition energy up to ∼11 and ∼116 GPa, respectively. These values are underestimated if the influence of the film roughness is not taken into account.     

MgO-templated carbon as a negative electrode material for Na-ion capacitors

In this study, MgO-templated carbon with different pore structures was investigated as a negative electrode material for Na-ion capacitors. With increasing the Brunauer–Emmett–Teller surface area, the irreversible capacity increased, and the coulombic efficiency of the 1st cycle decreased because of the formation of solid electrolyte interface layers. MgO-templated carbon annealed at 1000 °C exhibited the highest capacity and best rate performance, suggesting that an appropriate balance between surface area and crystallinity is imperative for fast Na-ion storage, attributed to the storage mechanism: combination of non-faradaic electric double-layer capacitance and faradaic Na intercalation in the carbon layers. Finally, a Na-ion capacitor cell using MgO-templated carbon and activated carbon as the negative and positive electrodes, respectively, exhibited an energy density at high power density significantly greater than that exhibited by the cell using a commercial hard carbon negative electrode.     

Surface enhanced Raman scattering and photoluminescence properties of catalytic grown ZnO nanostructures

Sword-like (diameter ranging from 40 nm to 300 nm) and needle-like zinc oxide (ZnO) nanostructures (average tip diameter ∼40 nm) were synthesized on annealed silver template over silicon substrate and directly on silicon wafer, respectively via thermal evaporation of metallic zinc followed by a thermal annealing in air. The surface morphology, microstructure, chemical analysis and optical properties of the grown samples were investigated by field emission scanning electron microscopy, X-ray diffraction, energy dispersive X-ray analysis, room temperature photoluminescence and Raman spectroscopy. The sword-like ZnO nanostructures grown on annealed silver template are of high optical quality compared to needle-like ZnO nanorods for UV emission and show enhanced Raman scattering.     

Structural, morphological and photoluminescence properties of W-doped ZnO nanostructures

W-doped ZnO nanostructures were synthesized at substrate temperature of 600 °C by pulsed laser deposition (PLD), from different wt% of WO₃ and ZnO mixed together. The resulting nanostructures have been characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy and photoluminescence for structural, surface morphology and optical properties as function of W-doping. XRD results show that the films have preferred orientation along a c-axis (0 0 L) plane. We have observed nanorods on all samples, except that W-doped samples show perfectly aligned nanorods. The nanorods exhibit near-band-edge (NBE) ultraviolet (UV) and violet emissions with strong deep-level blue emissions and green emissions at room temperature.     

Photoluminescence and Raman analysis of novel ZnO tetrapod and multipod nanostructures

Novel ZnO tetrapod and multipod nanostructures were successfully synthesized in bulk quantity through thermal evaporation method. The morphologies and structures of the ZnO nanostructures were characterized by scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The results revealed that the ZnO nanostructures consisted of tetrapods and multipods with tower-like legs. The ZnO nanostructures were of high purity and were well crystallized with wurtzite structure. The preferred growth direction of legs was found to be the [0 0 0 1] direction. Possible growth mechanisms were proposed for the formation of the ZnO nanostructures. Room temperature photoluminescence (PL) spectra showed that the as-synthesized ZnO nanostructures had a strong green emission centered at 495 nm and a weak ultraviolet emission at 383 nm. Raman spectroscopy was also adopted to explore the structural quality of the ZnO nanostructures.     

Optical properties of hydroxyapatite obtained by mechanical alloying

Calcium phosphate based bioceramics, mainly in the form of hydroxyapatite (HA), have been in use in medicine and dentistry for the last 20 years. Applications include coatings of orthopaedic and dental implants, alveolar ridge augmentation, maxillofacial surgery, otolaryngology, and scaffolds for bone growth and as powders in total hip and knee surgery. These materials exhibit several problems of handling and fabrication, which can be overcome by mixing with a suitable binder. In this paper, mechanical alloying has been used successfully to produce nanocrystalline powders of HA using five different experimental procedures. The milled HA were studied by X-ray powder diffraction, infrared and Raman scattering spectroscopy. For four different procedures, HA was obtained after a couple of hours of milling (on an average, 20 h of milling depending on the reaction procedure). The XRD patterns indicate that the grain size is within the range of 29-103 nm. This milling process, used to produce HA, presents the advantage that melting is not necessary and the powder obtained is nanocrystalline with extraordinary mechanical properties. The material can be compacted and transformed in solid ceramic samples. The high efficiency of the process opens a way to produce commercial amount of nanocrystalline HA. Due to the nanocrystalline character of this powder, their mechanical properties have changed and for this reason a pressure of 1 GPa is enough to shape the sample into any geometry.     

One-step synthesis and electrochemical behavior of LiMnO2 and its composite from MnO2 in the presence of glucose

LiMnO₂ and 0.23Li₂MnO₃·0.77LiMnO₂ were prepared by a convenient one-step solid-state reaction from MnO₂ using glucose as organic carbon resource. The crystal structure and morphology of the as-prepared materials was examined by X-ray powder diffraction and field emission scanning electron microscopy, respectively. The ration of Li to Mn was determined by means of atomic absorption spectrometry and the Li/Mn molar ratio in the products was 1.23. The electrochemical properties were investigated by charge-discharge test and electrochemical impedance measurements. The prepared composite material presented an initial discharge capacity of 45 mAh g^-1 and a good cycling performance with reversible capacity of 218 mAh g^-1 after 30 cycles. On the basis of the experimental results, the discharge efficiency of this composite material more than 100% was also discussed.     

Surface evolution of a gradient structured Ti in hydrogen peroxide solution

In this work, the interaction between hydrogen peroxide (H₂O₂) and a gradient structured Ti was investigated extensively. The gradient structured Ti (SMAT Ti) was produced by surface mechanical attrition treatment (SMAT), and then it was immersed in H₂O₂ solution for different time until 48 h at room temperature (25 °C). The structure and surface morphology evolution were examined by Raman spectra and scanning electron microscopy (SEM). The formation mechanism of nanoporous titania was discussed based on above results.     

Synthesis and electrochemical properties of Li4Ti5O12/C composite by the PVB rheological phase method

Spinel Li₄Ti₅O₁₂/C powders were synthesized successfully by a simple rheological phase method using polyvinylbutyral (PVB) as both template and carbon source. The structure and morphology characteristics of the composite were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy and transmission electron microscopy. The XRD results showed that the composite had a good crystallinity. Its average particle size was about 2.1 μm with a narrow size distribution as a result of homogeneous mixing of the precursors. The in situ carbon coating produced by decomposition of PVB played an important role in improving electrical conductivity, thereby enhancing the rate capacity of Li₄Ti₅O₁₂ as anode material in Li-ion batteries. The Li₄Ti₅O₁₂/C composite, synthesized at 800 °C for 15 h under argon, containing 0.98 wt% of carbon, exhibited better electrochemical properties in comparison with the pristine Li₄Ti₅O₁₂, which could be attributed to the enhanced electrical conductive network of the carbon coating on the particle surface.