Fabrication and performance of poly(methyl methacrylate) microfluidic chips with fiber cores

In this work, a piece of glass fiber was inserted into the channel of a poly(methyl methacrylate) (PMMA) electrophoresis microchip to enhance the electroosmotic flow (EOF) and the separation efficiency. The EOF value of the glass fiber-containing microchannel at pH 8.2 was determined to be 4.17 x 10(-4)cm2 V(-1)s(-1). The performance of the new microchip was demonstrated by its ability to separate and detect three purines coupled with end-column amperometric detection. In addition, a piece of trypsin-immobilized glass fiber was inserted into the channel of a PMMA microchip to fabricate a core-changeable microfluidic bioreactor that can be regenerated by changing the fiber. The in-channel fiber bioreactor has been coupled with matrix-assisted laser desorption ionization time-of-flight mass spectrometry for the digestion and peptide mapping of bovine serum albumin and myoglobin.     

Rinse and evaporation coating of poly(methyl methacrylate) microchip for separation of sodium dodecyl sulfate-protein complex

We developed a novel channel wall coating on a poly(methyl methacrylate) (PMMA) microchip using methylcellulose (MC) as a coating reagent to suppress electroosmotic flow (EOF) following the strong analytes adsorption via hydrophobic interaction with channel walls of PMMA. Our coating was obtained by first rinsing channel walls with MC-containing aqueous solution followed by evaporation. The coating made the hydrophilic channel wall lowering EOF by two orders of magnitude (1.2 x 10(-5)cm(2)V(-1)s(-1)) as well as reducing the hydrophobic adsorption. On the coated channel walls, we successfully separated sodium dodecyl sulfate-protein complexes with high reproducibility and efficiency using dextran as a lower viscosity protein separation medium.     

Low electroosmotic flow measurement by tilting microchip

A novel method for low electroosmotic flow (EOF) rates measurement by tilting microchip which based upon the hydrostatic pressure conception and sampling zone method is described. Sampling zone could be detected in the tilting microchip but not in non-tilting one due to the hydrostatic pressure driven. The method is fulfilled to calculate low EOF rates by detecting the liquid flow velocity driven by hydrostatic pressure, and difference between the apparent mobility of the migrating analyte in two modes is caused by the effect of hydrostatic pressure. And then the EOF rates in unknown low EOF microchip can be calculated. Different microchannels modified with bovine serum albumin (BSA), myoglobin (MB) and polyvinyl alcohol (PVA) were used to verify the method, the EOF rate value was 1.73+/-0.03, 1.21+/-0.05, 0.34+/-0.04 x 10(-4)cm(2) V(-1)s(-1), respectively. The results obtained by the proposed method were agreed well with conventional methods.     

Deposition of PEG onto PMMA microchannel surface to minimize nonspecific adsorption

A protein-resistant surface has been constructed on the poly(methyl methacrylate) (PMMA) microfluidic chips based on a one-step modification. The copolymer of butyl methacrylate (BMA) and poly(ethylene glycol) methyl ether methacrylate (PEGMA) is synthesized to introduce a dense PEG molecular brush-like coating on the PMMA microchannel surfaces via the anchoring effect of the hydrophobic BMA units. The PEGMA segments could produce hydrophilic domains formed on the interface so as to achieve stable electroosmotic flow, and less nonspecific adsorption toward biomolecules. The modification procedure and the properties of the poly(BMA-co-PEGMA)-coated surface have been characterized by FT-IR spectroscopy, confocal fluorescence microscopy, X-ray photoelectron spectroscopy and scanning electron microscopy. The water contact angle and electroosmotic flow of PEG-modified PMMA microchip are measured to be 36 degrees and 5.4 x 10(-4) cm(2) V(-1) s(-1), while those of 73 degrees and 1.9 x 10(-4) cm(2) V(-1) s(-1) for native one, respectively. The PEG-modified microchip has been applied for the electrophoresis separation of proteins, corresponding to the theoretical efficiencies about 16 300 and 412 300 plates m(-1). In the interest of achieving efficient separation while minimizing biofoulings from the serum and plasma, the fabrication of PEG-coated microfluidic chips would provide a biocompatible platform for complex biological analysis.     

Microfluidic flow control on charged phospholipid polymer interface

A type of charged phospholipid polymer biointerface was constructed on a quartz microfluidic chip to control the electroosmotic flow (EOF) and to suppress non-specific protein adsorption through one-step modification. A negatively charged phospholipid copolymer containing 2-methacryloyloxyethyl phosphorylcholine (MPC), n-butyl methacrylate (BMA), potassium 3-methacryloyloxypropyl sulfonate (PMPS) and 3-methacryloxypropyl trimethoxysilane (MPTMSi) moieties (referred to as PMBSSi) was synthesized to introduce such phosphorylcholine segments as well as surface charges onto the silica-based microchannels via chemical bonding. At neutral pH, the homogenous microchannel surface modified with 0.3 wt% PMBSSi in alcoholic solution, retained a significant cathodic EOF ((1.0 +/- 0.1) x 10(-4) cm(2) V(-1) s(-1)) with approximately one-half of the EOF of the unmodified microchannel ((1.9 +/- 0.1) x 10(-4) cm(2) V(-1) s(-1)). Along with another non-charged copolymer (poly(MPC-co-MPTMSi), PMSi), the regulation of the surface charge density can be realized by adjusting the concentration of PMBSSi or PMSi initial solutions for modification. Coincidently, the zeta-potential and the EOF mobility at neutral pH showed a monotonically descending trend with the decrease in the charge densities on the surfaces. This provides a simple but feasible approach to controlling the EOF, especially with regard to satisfying the requisites of miniaturized systems for biological applications requiring neutral buffer conditions. In addition, the EOF in microchannels modified with PMBSSi and PMSi could maintain stability for a long time at neutral pH. In contrast to the EOF in the unmodified microchannel, the EOF in the modified microchannel was only slightly affected by the change in pH (from 1 to 10). Most importantly, although PMBSSi possesses negative charges, the non-specific adsorptions of both anionic and cationic proteins (considering albumin and cytochrome c, respectively, as examples) were effectively suppressed to a level of 0.15 microg cm(-2) and lesser in the case of the 0.3 wt% PMBSSi modification. Consequently, the variation in the EOF mobility resulting from the protein adsorption was also suppressed simultaneously. To facilitate easy EOF control with compatibility to biomolecules delivered in the microfluidic devices, the charged interface described could provide a promising option.     

Measurement of electroosmotic flow in plastic imprinted microfluid devices and the effect of protein adsorption on flow rate.

Several commercially available plastic materials were used as substrates in the fabrication of microfluid channels for biochemical analysis. Protocols for fabrication using the wire-imprinting method are reported for polystyrene, polymethylmethacrylate and a copolyester material. Channel sealing was accomplished by low-temperature bonding of a substrate of similar material; therefore, each channel was composed of a single material on all sides. The electroosmotic flow in 25-microm imprinted channels was evaluated for each substrate material. The copolyester material exhibited the highest electroosmotic flow mobility of 4.3 x 10(-4) cm2 V(-1) s(-1) which is similar to that previously reported for fused-silica capillaries. Polystyrene exhibited the lowest electroosmotic flow mobility of 1.8 x 10(-4) cm2 V(-1) s(-1). Plots of linear velocity versus applied electric field strength were linear from 100 V cm(-1) to 500 V cm(-1) indicating that heat dissipation is effective for all substrates in this range. Electroosmotic flow was reevaluated in the plastic channels following incubation in antibody solution to access the non-specific binding characteristics of a common biochemical reagent onto the substrate materials. All materials tested showed a high degree of non-specific adsorption of IgG as indicated by a decrease in the electroosmotic flow mobility in post-incubation testing.     

Characterization of SU-8 for electrokinetic microfluidic applications

The characterization of SU-8 microchannels for electrokinetic microfluidic applications is reported. The electroosmotic (EO) mobility in SU-8 microchannels was determined with respect to pH and ionic strength by the current monitoring method. Extensive electroosmotic flow (EOF), equal to that for glass microchannels, was observed at pH > or =4. The highest EO mobility was detected at pH > or =7 and was of the order of 5.8 x 10(-4) cm(2) V(-1) s(-1) in 10 mM phosphate buffer. At pH < or =3 the electroosmotic flow was shown to reverse towards the anode and to reach a magnitude of 1.8 x 10(-4) cm(2) V(-1) s(-1) in 10 mM phosphate buffer (pH 2). Also the zeta-potential on the SU-8 surface was determined, employing lithographically defined SU-8 microparticles for which a similar pH dependence was observed. SU-8 microchannels were shown to perform repeateably from day to day and no aging effects were observed in long-term use.     

A chip-based capillary electrophoresis-contactless conductivity microsystem for fast measurements of low-explosive ionic components

A miniaturized analytical system for separating and detecting inorganic explosive residues, based on the coupling of a micromachined capillary electrophoresis (CE) chip with a contactless conductivity detector is described. The low electroosmotic flow (EOF) of the poly(methylmethacrylate) (PMMA) chip material facilitates the rapid switching between analyses of cations and anions using the same microchannel and run buffer (and without an EOF modifier), and hence offers rapid (< 1 min) measurement of seven explosive-related cations and anions. Experimental parameters relevant to the separation and detection processes have been optimized. Addition of a 18-crown-6 ether modifier has been used for separating the peaks of co-migrating potassium and ammonium ions. The ionic-explosive microchip system combines the distinct advantages of contactless conductivity detection with the attractive features of plastic CE microchips. The new microsystem offers great promise for monitoring explosive-related ions at the sample source, with significant advantages of speed/warning, efficiency, cost, or sample size.     

注塑型聚甲基丙烯酸甲酯多通道微流控芯片的研制及其性能考察

微流控芯片技术因具有微量、快速、高效和高通量等特点,已成为分析化学领域中的研究热点之一．在微流控芯片中,最常见的可用作芯片的材料为玻璃、石英和各种塑料．玻璃和石英有很好的电渗性和光学性质,可采用标准的刻蚀工艺加工和用化学方法进行表面改性,但加工成本较高,封接难度较大．     

Control of electroosmotic flow in laser-ablated and chemically modified hot imprinted poly(ethylene terephthalate glycol) microchannels

The fabrication of microchannels in poly(ethylene terephthalate glycol) (PETG) by laser ablation and the hot imprinting method is described. In addition, hot imprinted microchannels were hydrolyzed to yield additional charged organic functional groups on the imprinted surface. The charged groups are carboxylate moieties that were also used as a means for the further reaction of different chemical species on the surface of the PETG microchannels. The microchannels were characterized by fluorescence mapping and electroosmotic flow (EOF) measurements. Experimental results demonstrated that different fabrication and channel treatment protocols resulted in different EOF rates. Laser-ablated channels had similar EOF rates (5.3+/-0.3 x 10(-4) cm(2)/Vs and 5.6+/-0.4 x 10(-4) cm(2)/Vs) to hydrolyzed imprinted channels (5.1+/-0.4 x 10(-4) cm(2)/Vs), which in turn demonstrated a somewhat higher flow rate than imprinted PETG channels that were not hydrolyzed (3.5+/-0.3 x 10(-4) cm(2)/Vs). Laser-ablated channels that had been chemically modified to yield amines displayed an EOF rate of 3.38+/- 0.1 x 10(-4) cm(2)/Vs and hydrolyzed imprinted channels that had been chemically derivatized to yield amines showed an EOF rate of 2.67+/-0.6 cm(2)/Vs. These data demonstrate that surface-bound carboxylate species can be used as a template for further chemical reactions in addition to changing the EOF mobility within microchannels.     

Protein separation and surfactant control of electroosmotic flow in poly(dimethylsiloxane)-coated capillaries and microchips

A thermally pyrolyzed poly(dimethylsiloxane) (PDMS) coating intended to prevent surface adsorption during capillary electrophoretic (CE) [Science 222 (1983) 266] separation of proteins, and to provide a substrate for surfactant adsorption for electroosmotic mobility control was prepared and evaluated. Coating fused-silica capillaries or glass microchip CE devices with a 1% solution of 100 cSt silicone oil in CH2Cl2, followed by forced N2 drying and thermal curing at 400 degrees C for 30 min produced a cross-linked PDMS layer. Addition of 0.01 to 0.02% Brij 35 to a 0.020 M phosphate buffer gave separations of lysozyme, cytochrome c, RNase, and fluorescein-labeled goat anti-human IgG Fab fragment. Respective plates/m typically obtained at 20 kV (740 V cm(-1)) were 2, 1.5, 1.25, and 9.4-10(5). In 50 mM ionic strength phosphate, 0.01% Brij 35 running buffer, the electroosmotic flow observed was about 25% of that in a bare capillary, and showed no pH dependence between pH 6.3-8.2. Addition of sodium dodecylsulfate (SDS) or cetyltrimethylammonium bromide (CTAB) to this running buffer allowed ready control of electroosmotic mobility, mu(eo). Concentrations of SDS between 0.005 to 0.1% resulted in mu(eo) ranging from 3 to 5 x 10(-4) cm2 V(-1) s(-1). Addition of 1 to 2.3 x 10(-4)% (2.7-6.3 microM) CTAB caused flow reversal. CTAB concentrations between 3.5 x 10(-4) and 0.05% (0.0014-1.37 mM) allowed control of mu(eo) between -1 x 10(-4) and -5.0 x 10(-4) cm2 V(-1) s(-1). For both surfactants the added presence of 0.01% Brij 35 provided slowly varying changes in mu(eo) with charged surfactant concentration.     

Surfactant-induced electroosmotic flow in microfluidic capillaries

Control of EOF in microfluidic devices is essential in applications such as protein/DNA sizing and high‐throughput drug screening. With the growing popularity of poly(methyl methacrylate) (PMMA) as the substrate for polymeric‐based microfludics, it is important to understand the effect of surfactants on EOF in these devices. In this article, we present an extensive investigation exploring changes in EOF rate induced by SDS, polyoxyethylene lauryl ether (Brij35) and CTAB in PMMA microfluidic capillaries. In a standard protein buffer (Tris‐Glycine), PMMA capillaries exhibited a cathodic EOF with measured mobility of 1.54 ± 0.1 (× 10^?4 cm²/V.s). In the presence of surfactant below a critical concentration, EOF was independent of surfactant concentration. At high concentrations of surfactants, the electroosmotic mobility was found to linearly increase/decrease as the logarithm of concentration before reaching a constant value. With SDS, the EOF increased by 257% (compared to buffer), while it was decreased by 238% with CTAB. In the case of Brij35, the electroosmotic mobility was reduced by 70%. In a binary surfactant system of SDS/CTAB and SDS/Brij35, addition of oppositely charged CTAB reduced the SDS‐induced EOF more effectively compared to nonionic Brij35. We propose possible mechanisms that explain the observed changes in EOF and zeta potential values. Use of neutral polymer coatings in combination with SDS resulted in 50% reduction in the electroosmotic mobility with 0.1% hydroxypropyl methyl cellulose (HPMC), while including 2% poly (N,N‐dimethylacrylamide) (PDMA) had no effect. These results will potentially contribute to the development of PMMA‐based microfluidic devices.     

Modification of a poly(methyl methacrylate) injection-molded microchip and its use for high performance analysis of DNA

Inexpensive and permanently modified poly(methyl methacrylate)(PMMA) microchips were fabricated by an injection-molding process. A novel sealing method for plastic microchips at room temperature was introduced. Run-to-run and chip-to-chip reproducibility was good, with relative standard deviation values between 1-3% for the run-to-run and less than 2.1% for the chip-to-chip comparisons. Acrylonitrile-butadiene-styrene (ABS) was used as an additive in PMMA substrates. The proportions of PMMA and ABS were optimized. ABS may be considered as a modifier, which obviously improved some characteristics of the microchip, such as the hydrophilicity and the electro-osmotic flow (EOF). The detection limit of Rhodamine 6G dye for the modified microchip on the home-made microchip analyzer showed a dramatic 100-fold improvement over that for the unmodified PMMA chip. A detection limit of the order of 10(-20) mole has been achieved for each injected psiX-174/HaeIII DNA fragment with the baseline separation between 271 and 281 bp, and fast separation of 11 DNA restriction fragments within 180 seconds. Analysis of a PCR product from the tobacco ACT gene was performed on the modified microchip as an application example.     

Separation of acidic and basic compounds in capillary electrochromatography with polymethacrylate-based monolithic columns

Methacrylate-based monolithic columns with electroosmotic flow (EOF) or very weak EOF are prepared by in situ copolymerization in the presence of a porogen in fused-silica capillaries pretreated with a bifunctional reagent. Satisfactory separations of acidic and basic compounds on the column with EOF at either low or high pH are achieved, respectively. With sulfonic groups as dissociation functionalities, sufficient EOF mobility still remains as high as 1.74 x 10(-4) cm2 s(-1) V(-1) at low pH. Under this condition, seven acidic compounds are readily separated within 5.7 min. Moreover, at high pH, the peak shape of basic compounds is satisfactory without addition of any masking amines into running mobile phase since the secondary interaction between the basic compounds and the monolithic stationary phase are minimized at high pH. Reversed-phase mechanism for both acidic and basic compounds is observed under investigated separation conditions. In addition, possibilities of acidic and basic compound separations on a monolithic column with extremely low EOF are discussed.     

A sol-gel-modified poly(methyl methacrylate) electrophoresis microchip with a hydrophilic channel wall

A sol-gel method was employed to fabricate a poly(methyl methacrylate) (PMMA) electrophoresis microchip that contains a hydrophilic channel wall. To fabricate such a device, tetraethoxysilane (TEOS) was injected into the PMMA channel and was allowed to diffuse into the surface layer for 24 h. After removing the excess TEOS, the channel was filled with an acidic solution for 3 h. Subsequently, the channel was flushed with water and was pretreated in an oven to obtain a sol-gel-modified PMMA microchip. The water contact angle for the sol-gel-modified PMMA was approximately 27.4 degrees compared with approximately 66.3 degrees for the pure PMMA. In addition, the electro-osmotic flow increased from 2.13x10(-4) cm2 V(-1) s(-1) for the native-PMMA channel to 4.86x10(-4) cm2 V(-1) s(-1) for the modified one. The analytical performance of the sol-gel-modified PMMA microchip was demonstrated for the electrophoretic separation of several purines, coupled with amperometric detection. The separation efficiency of uric acid increased to 74,882.3 m(-1) compared with 14,730.5 m(-1) for native-PMMA microchips. The result of this simple modification is a significant improvement in the performance of PMMA for microchip electrophoresis and microfluidic applications.     

Control of the EOF in CE using polyelectrolytes of different charge densities

The control of the EOF direction and magnitude remains one of the more challenging issues for the optimization of separations in CE. In this work, we investigated the possibility to use variously charged polyanions for a fine-tuning of the EOF using polyelectrolyte multilayers. For that purpose, polyanions of poly(acrylamide-co-2-acrylamido-2-methyl-1-propanesulfonate) (PAMAMPS) with different chemical charge rates varying between 3 and 100% were used. These copolymers are statistic hydrophilic copolymers of acrylamide (AM) and 2-acrylamido-2-methyl-1-propanesulfonate (AMPS). The study of the influence of the chemical charge rate (AMPS molar proportion in the copolymer) on the electroosmotic mobility (mu(eo)) of a capillary modified by a polyelectrolyte bilayer (polycation/PAMAMPS) revealed that the fine-tuning of the EOF was possible, at least for cathodic or slightly anodic EOF (micro(eo) from -5 x 10(-5) to +35 x 10(-5) cm(2)V(-1)s(-1)). Electroosmotic mobility values were compared with the free-draining electrophoretic mobilities of the PAMAMPS constituting the last layer of the capillary coating. The stability of the EOF is discussed in detail on the basis of successive determinations of electroosmotic mobility and migration times. The application to the separation of a model peptide mixture demonstrated the interest (and the simplicity) of this approach for optimizing resolution and analysis time. Experimental resolutions were compared to the theoretical ones that we would obtain on a fused-silica capillary having the same EOF as the coated capillary.     

Channel wall coating on a poly-(methyl methacrylate) CE microchip by thermal immobilization of a cellulose derivative for size-based protein separation

We demonstrate channel wall coating using a cellulose derivative on a poly-(methyl methacrylate) (PMMA) CE microchip to eliminate EOF disturbing protein separation. The channel walls were modified by preconditioning with a solution containing the cellulose derivative and then thermally evaporating the solution to produce hydrophilic channel walls which prevent adsorption of analytes via a hydrophobic interaction. When the PMMA substrate was coated with the cellulose derivative hydroxypropylmethylcellulose (HPMC) 90SH, the water contact angle on the coated substrate was decreased (up to 15 degrees ) and EOF was significantly suppressed (up to 4.0 x 10(-6) cm2.V(-1)s(-1)). Three proteins (20.5, 68.0, and 114.6 kDa) were successfully separated on the 0.15% HPMC 90SH-coated channel walls with good reproducibility of migration time (RSD <1.75%) and high efficiency (theoretical plate number per meter: 2.62 x 10(5)).     

Influencing electroosmotic flow and selectivity in open tubular electrochromatography by tetrakis(pentafluorophenyl)porphyrin as capillary wall modifier

A physically adsorbed and covalently bonded porphyrin derivative, 5,10,15,20-tetrakis(pentafluorophenyl)porphyrin, H₂TPFPP, has been used as a fused-silica capillary wall modifier in open tubular capillary electrochromatography (OT-CEC), and its influence on the electroosmotic flow (EOF) velocity and on the selectivity of OT-CEC separations of a set of model aromatic carboxylic acids has been tested. Whereas most of the coatings of this category bring about an increase in selectivity with a concomitant slow down of the EOF, H₂TPFPP coating, depending on pH of the background electrolyte used, resulted both in decreasing of EOF at pH 8.5 by 5% and in increasing of EOF by 10–43% at pH 6 and 5, respectively. The separation efficiency and the resolution of aromatic carboxylic acids separation in coated capillaries, namely in that one with covalent coating, were better than in the bare fused-silica capillary. The perspectives of H₂TPFPP as capillary wall modifier are visualized in introducing well defined electroosmotic properties of materials used for miniaturized separation channels preparation in chip-based electromigration devices.     

Polyelectrolyte-modified short microchannel for cation separation

Three alkali cations, potassium, sodium, and lithium, have been separated within 15 s in a 1 cm long polymer microchip. The separation microchannel is modified by a polycation, poly(allylammonium chloride), which makes the channel surfaces positively charged leading to a reversed electroosmotic flow (EOF) when compared to bare channels. Due to the decreased apparent mobility of the cations, the separation resolution is improved allowing the use of shorter channels.     

Photochemically patterned poly(methyl methacrylate) surfaces used in the fabrication of microanalytical devices

We report here the photochemical surface modification of poly(methyl methacrylate), PMMA, microfluidic devices by UV light to yield pendant carboxylic acid surface moieties. Patterns of carboxylic acid sites can be formed from the micrometer to millimeter scale by exposure of PMMA through a contact mask, and the chemical patterns allow for further functionalization of PMMA microdevice surfaces to yield arrays or other structured architectures. Demonstrated here is the relationship between UV exposure time and PMMA surface wettability, topography, surface functional group density, and electroosmotic flow (EOF) of aqueous buffer solutions in microchannels made of PMMA. It is found that the water contact angle on PMMA surfaces decreases from 70 degrees to 24 degrees after exposure to UV light as the result of the formation of carboxylic acid sites. However, upon rinsing with 2-propanol, the water contact angle increases to approximately 80 degrees , and this increase is attributed to changes in surface roughness resulting from removal of low molecular weight PMMA formed from scission events. In addition, the surface roughness and surface coverage of carboxylic acid groups exhibit a characteristic trend with UV exposure time. Electroosmotic flow (EOF) in PMMA microchannels increases upon UV modification and is pH dependent. The possible photolysis mechanism for formation of carboxylic acid groups on PMMA surfaces under the conditions outlined in this work is discussed.