Electrocrystallizations of copper on glassy carbon in CuCl2 silica sol and aqueous solutions

Electrocrystallizations of copper from both CuCl₂ silica sol and aqueous solutions were studied by the chronoamperometry technique.It was found that current density contributions of the double-layer charging（iDL） in current-time transients（CTTs） from both of the solutions were large.An adsorption-nucleation based model was proposed to analyze quantitatively the CTTs,by which copper electrocrystallization mechanism was characterized as progressive nucleation with 3D growth（3DP） under diffusion control.The diffusion coefficient of copper ions and the AN_∞products in aqueous solutions were larger than that in silica sols, which indicated that copper nucleation was inhibited in sol solution.The large iDL may be resulted from the adsorption of chloride ions on the electrode surface.     

THERMAL-SENSITIVE BETA-CYCLODEXTRIN-CONTAINED POLY(N-ISOPROPYLACRYLAMIDE) HYDROGELS CROSS-LINKED BY Si―O―Si BONDS

A series of novel p（N-isopropylacrylamide） （PNIPAM） hydrogels were synthesized by radical copolymerization of N-isopropylacrylamide （NIPAM） and 3-methacryloxypropyltrimethoxysilane （MPTMS）. The copolymers were then crosslinked through hydrolysis of the siloxane in acetic acid/water mixed solvent. Beta-cyclodextrin （Beta-CD） was introduced into the polymeric networks by condensation of 3-glycidoxypropyltrimethoxysilane derived beta-cyclodextrin （KH560-beta-CD） with MPTMS under acidic condition. These gels were heterogeneous, porous and exhibited fast deswelling kinetics when the temperature was elevated to above lower critical solution temperature （LCST）. The swelling ratios of the gels containing beta-CD at room temperature were higher than that of the normal PNIPAM hydrogel, which was caused by the lower crosslinking density in beta-CD contained gels. In comparison to that of the normal PNIPAM gel, the amount of loaded-drug in the hydrogel containing beta-CD was higher, and the release time of 5-fluorouracil （5-Fu） was prolonged, which was attributed to the formation of inclusion compounds between 5-Fu and beta-CD in gel network.     

OPTIMIZATION OF THE SYNTHESIS OF ACRYLAMIDE HYDROGEL BY γ-RAY IRRADIATION

Hydrogels have been synthesized from 10%, 20%, 30%, 40%, 50% and 60% aqueous solutions of acrylamide monomer by gamma radiation employing doses in the range of 0.2-30 kGy from a Co-60 source. The effect of solution concentration, y-ray dose, pH and time was studied in order to observe the optimizing conditions in the characterization of hydrogels. Gel fraction increases with dose for all concentrations indicating hundred-percentage conversion of gel at doses ≥5 kGy for homogenous solutions in the range of 20%-50% concentration. On the other hand, 10% solution provides conversion less than 86% even at 30 kGy, whereas 60% monomer makes an inhomogeneous solution which stile gives about 100% gel fraction. Swelling of hydrogels under water with respect to time varies with both the doses and concentrations due to the change of crosslinking density in the gels. The maximum volume change of hydrogels during swelling and water desorption mainly occurs within 24 h. Swelling is also enhanced with the rise of pH due to change of ionic content of the solvent. Considering the amount of gel fraction and the properties of hydrogel, the samples prepared from 20% solution at 5 kGy show better results. Moreover, the effect of bacteria on hydrogel was found to be nil, suggesting a prohibition of growth of microorganism in it.     

SWELLING EQUILIBRIUM OF NONIONIC POLYACRYLAMIDE HYDROGEL IN AQUEOUS SALT SOLUTIONS

A series of nonionic polyacrylamide hydrogels, using acrylamide as monomer and N,N＇-methylene diacrylamide as crosslinking agent, were prepared by the free radical polymerization in aqueous solution. Swelling equilibria for the gels were carried out in aqueous solutions of NaCl, KCI, CaCl2, Na2HPO4 and K2HPO4 with concentration ranging from 10^-3 to 5mol/kgH2O at 25 ℃. Experimental results revealed that the chlorides and phosphates cause a different behavior at higher salt concentration. The swelling ratio increases with increasing concentration of chlorides salts, while decreases with the increased phosphates salt concentration. The phenomena seem to be related to the different interactions of chloride and hydrogen phosphate ions with the network groups. Furthermore, the effects of different concentration of crosslinking agent and total monomers on gel swelling performance were also investigated.     

Synthesis and Characterization of Self-oscillating P（AA-co-AM）/PEG SemiIPN Hydrogels Based on a p H Oscillator in Closed System

Various semi-interpenetrating polymer network（semi-IPN） hydrogels composed of pore-forming agent polyethylene glycol（PEG）, acrylic acid（AA） and acrylamide（AM） were prepared by using free radical polymerization with a two-step method. The chemical structures of the synthesized hydrogels were characterized by FTIR spectroscopy and the morphologies were studied by scanning electron microscopy（SEM） method. The swelling properties, such as the p Hresponsive behavior, salt sensitivity, oscillatory swelling/de-swelling behaviors in different solutions with various p H values and self-oscillating behaviors in bath p H oscillator were investigated in detail. The results revealed that the prepared hydrogels exhibited high p H sensitivity and excellent salt sensitivity when the p H values of the medium changes from 3.0 and 7.0 and well reversible properties by undergoing a number of swelling/de-swelling recycles. In particular, the hydrogels exhibited self-oscillation behavior in a closed system containing Br O3？-SO32？-Fe（CN）64？-H＋. This study may create a new possibility as biomaterial for new self-walking actuators and other devices.     

Simultaneous LC-MS/MS Determination of Danshensu and Paeoniflorin for Permeability Studies in Caco-2 Intestinal Absorption Model

A high sensitive method based on liquid chromatography tandem mass spectrometry（LC-MS/MS） was developed and validated for the study of permeability of danshensu（DS） and paeoniflorin（PF） in Caco-2 intestinal absorption model. The DS and PF were extracted from cell culture by vacuum-lyophilizing and then separated on a Zorbax Stable Bond C18 column with 0.1% acetic acid aqueous solution and methanol as mobile phase. Detection was carried out by negative electrospray ionization（ESI ） with selected reaction monitoring（SRM） mode. The apparent permeability coefficients（Papp） of DS and PF in Caco-2 cell medium were calculated and the effects of verapamil on the coefficients Papp of the two test compounds were also illustrated. The permeability of PF was much better than that of DS when the two compounds were administrated individually. Co-administration of DS and PF led to the decrease of the transport from apical side to basolateral side for both the compounds. However, the transport in the contrary direction were accelerated. It was also observed that verapamil could accelerate the transport of the test compounds from apical side to basolateral side. However, the absorption-enhanced effect of verapamil was attenuated when DS and PF were co-administrated. These observations suggest that both passive diffusion and active efflux involved in P-gp would effect the passage of DS and PF across Caco-2 cell monolayer. At the same time, the co-administration of DS and PF to an alteration of transport behavior, which suggests that the interaction must be taken into account when ‘n-in-one＇ samples were used in Caco-2 intestinal model.     

Effect of dry density on 125I diffusion in GMZ bentonite

Gaomiaozi(GMZ) bentonite is regarded as the favorable candidate backfilling material for a potential repository in China.It is important to understand the diffusion behavior of 125 I in GMZ bentonite and compare the diffusion behavior in GMZ and other types of bentonite like MX-80,Avonlea,etc.Therefore,through-and out-diffusion experiments were conducted to obtain the effective diffusion coefficient(D e) and distribution coefficient(K d).A computer code named Fitting for diffusion coefficient(FDP) was used for the experimental data processing and theoretical modeling.At the dry density of GMZ bentonite from 1600-2000 kg/m 3,the D e values of 125 I were(2.4-20.4) × 10-12 m 2 /s and K d values were constants.At dry density above 1800 kg/m 3,the diffusion behaviors were almost the same,indicating that the anion exclusion was ineffective.Out-diffusion results showed that the species of 125 I may be changed during the diffusion processing.It was probably caused by some organic matters or reducing substances in GMZ bentonite.Since the main composition of bentonite is montmorillonite,similar diffusion parameters were obtained in GMZ and other types of bentonite.The relationship of D e and accessible porosity(acc) could be described by Archie’s law with exponent n = 1.2-2.8 for 125 I diffusion in bentonite,whereas n = 2.0 in GMZ bentonite.Furthermore,bentonite with the dry density of 1800 kg/m 3 was proposed as the backfilling materials used in the construction of high level radioactivity waste repository.     

Synthesis of new superabsorbent poly(NIPAAm/AA/N-allylisatin)nanohydrogel for effective removal of As(Ⅴ) and Cd(Ⅱ) toxic metal ions

The present studies highlight the effective removal of As（V） and Cd（II） from aqueous solutions by superabsorbent poly （NIPAAm/AA/N-allylisatin） nanohydrogel. Batch removal studies were performed as a function of treatment time, initial metal ion concentration, pH, and adsorbent dose. TEM micrographs confirm the particle size distribution in the range between 5 nm and 10 rim. The simple and metal ions adsorbed nanohydrogels were characterized by FF-IR, TGA, and EDX analysis. Finally, the equilibrium removal efficiency of the nanohydrogel was analyzed according to the Langmuir and Freundlich adsorption isotherm models which showed the removal of As（V） and Cd（II） metal ions fitted to Freundlich and Langmuir isotherms, respectively. Removal efficiency order of the metal ions is As（V） 〉 Cd（II）.     

Dynamic Properties of Polyampholyte Hydrogel Elucidated by Proton NMR Spin-spin Relaxation Time

1H spin-spin relaxation time（T2） measurement of polyampholyte hydrogel poly（methylacrylic acidacryloyloxyethyl trimethylammonium chloride）[P（MA-DAC）] in different pH, ionic strength and temperature was carried out to reveal the molecular mobility. Spontaneous volume transition of the polyampholyte hydrogel was also investigated by spin-spin relaxation time measurement. Meanwhile T2 and the proton component fraction were acquired to study the swelling behaviour of the hydrogel. Moreover the changes of T2 characterized the molecular mo- bility of polyampholyte hydrogel in various swelling states. And the results suggest that the mobility of the main chains and a few free side chains（the long T2） of P（MA-DAC） was dominated by the mesh size in the hydrogel net- work, depending on the swelling ratio（Q） and the mobility of the side chains（the short T2） was influenced by electrostatic interaction between different charges in polymer side chains. Finally the T2 measurements of P（MA-DAC） hydrogel in the spontaneous swelling-deswelling process demonstrated the electrostatic interaction of the charged side chains caused deswelling behavior. At the same time, the mobility state transition temperature of the charged side chains was also studied by the lH spin-spin relaxation time measurements, and the transition activation energy of the side chains is 2.72 kJ.     

RADIATION SYNTHESIS AND CHARACTERIZATION OF POLY(AA-co-NVP)/CLAY HYDROGELS

The pH-sensitive P(AA-co-NVP)/clay hydrogels were prepared with the monomers of acrylic acid(AA)and N-vinyl-2-pyrrolidone(NVP)based onγ-ray irradiation technique.The influence of pH values of buffer solutions and contents of clay and NVP on the equilibrium swelling ratio(SR)and compressive properties of the hydrogels was investigated in detail.The results of swelling property tests showed that,with the increase of clay content,the SR of hydrogels increases in the same buffer solution,and the SR of hydrog...     

Adsorption and controlled release of Chlortetracycline HCl by using multifunctional polymeric hydrogels

Adsorption and controlled release of Chlortetracycline HCl to and from multifunctional polymeric materials (HEMA/MAA) hydrogels were investigated. P(HEMA/MAA) hydrogels were synthesized by gamma radiation-induced copolymerization of 2-hydroxyethylmethacrylate (HEMA) and methacrylic acid (MAA) in aqueous solution. The influence of copolymer composition and pH value of the surrounding medium on the type of water diffusion into the glassy polymer were discussed. Drug, Chlortetracycline HCl containing hydrogels, with different drug concentration to polymer ratios, was loaded by direct adsorption method. The influence of MAA content in the gel on the adsorption capacities of hydrogel was studied. Chlortetracycline HCl adsorption capacity of hydrogels was found to increase from 8 to 138 mg Chlortetracycline HCl per gram dry gel with increasing amount of MAA in the gel system and drug concentration. The effect of pH on the releasing behavior of Chlortetracycline HCl from gel matrix was investigated. In vitro drug release studies in different buffer solutions show that the basic parameters affecting the drug release behavior of hydrogel are the pH of the solution and MAA content of hydrogel.     

Removal of Pb2+ and Cd2+ ions from aqueous solutions using guanidine modified hydrogels

In this study, experimental measurements have been made on the batch adsorption of cadmium and lead ions from aqueous solutions using poly(guanidine modified 2‐acrylamido‐2‐methylpropan sulfonic acid/acrylic acid/N‐vinylpyrrolidone/2‐Hydroxyethyl methacrylate), P(AMPSG/AAc/NVP/HEMA) hydrogels. The guanidyl end group bearing AMPSG monomer was synthesized from the reaction of AMPS and guanidine. The hydrogels were prepared by UV‐curing technique. The morphology of the dry H10‐hydrogel sample was examined by SEM. The influence of the uptake conditions, such as pH, functional monomer per cent, contact time, initial feed concentration, and foreign metal ions on the metal ion binding capacity of hydrogel, was also tested. The selectivity of the hydrogel toward the different metal ions tested was Hg(II) > Pb(II) > Au(III) > Cd(II). The adsorption isotherm models were applied to the experimental data, and it was seen that the Langmuir isotherm model was the best fit for the adsorption of Cd(II) and Pb(II) ions on P(AMPSG/AAc/NVP/HEMA) hydrogel. It was found that adsorbed lead and cadmium ions on P(AMPSG/AAc/NVP/HEMA) hydrogel can be effectively desorbed by acid leaching and the regenerated P(AMPSG/AAc/NVP/HEMA) hydrogel can be reused almost five times less without any loss of adsorption capacity. Copyright © 2009 John Wiley & Sons, Ltd.     

温度敏感聚(N-异丙基丙烯酰胺-co-甲基丙烯酰氧乙基二甲基辛基溴化铵)水凝胶的溶胀性能研究

由于改变亲水／疏水单体比值、与离子单体共聚心、改变凝胶内部结构等均可不同程度地调整温敏水凝胶的溶胀性能,本研究选择一种既含疏水烷基又含季铵盐正离子型亲水基团的两亲性单体——甲基丙烯酰氧乙基二甲基辛基溴化铵（ADMOAB）,结构如示意图1所示．与N-异丙基丙烯酰胺（NIPAM）聚合,制备了P（NIPAM-co-ADMOAB）共聚水凝胶,以便在引入离子型结构单元的同时,改变凝胶体系中亲水／疏水单体比值,避免单纯增加疏水单体引起的水凝胶溶胀性降低问题,并考察了ADMOAB对水凝胶溶胀性能的影响,对该类水凝胶迄今鲜见相关文献报道．该研究对进一步了解水凝胶的构效关系、探索有效控制溶胀性能的途径具有积极意义．     

Swelling and drug release behavior of poly(2-hydroxyethyl methacrylate/itaconic acid) copolymeric hydrogels obtained by gamma irradiation

The new copolymeric hydrogels based on 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA) were prepared by gamma irradiation, in order to examine the potential use of these hydrogels in controlled drug release systems. The influence of IA content in the gel on the swelling characteristics and the releasing behavior of hydrogels, and the effect of different drugs, theophylline (TPH) and fenethylline hydrochloride (FE), on the releasing behavior of P(HEMA/IA) matrix were investigated in vitro. The diffusion exponents for swelling and drug release indicate that the mechanisms of buffer uptake and drug release are governed by Fickian diffusion. The swelling kinetics and, therefore, the release rate depends on the matrix swelling degree. The drug release was faster for copolymeric hydrogels with a higher content of itaconic acid. Furthermore, the drug release for TPH as model drug was faster due to a smaller molecular size and a weaker interaction of the TPH molecules with(in) the P(HEMA/IA) copolymeric networks.     

Interaction of urea with poly(2-hydroxyethyl methacrylate) hydrogels

The interaction of poly(2-hydroxyethyl methacrylate) [poly(HEMA)] and other similar hydrogels with dilute urea solution has been studied by a variety of techniques, including swelling experiments, fluorescence quenching, near infrared spectroscopy and fundamental band infrared spectroscopy. The results obtained indicate that the anomalous swelling behavior of poly(HEMA) gels in the presence of such dilute urea solutions is probably not due to the disruption of a secondary hydrophobic bond structure as has been generally believed. Although poly(HEMA) gels do contain sites that can participate in hydrophobic bonding, the evidence gathered indicates that dilute urea solutions have no effect on such bonds. A plausible model that does fit all the data involves the interaction of urea with a secondary structure composed of hydrogen-bonded hydroxyl groups, stabilized by the exclusion of water molecules from the regions containing the bonds.     

Stimulus response and molecular structural modification of polyacrylamide gel in nitric acid: A study by Raman,FTIR, and photoluminescence techniques

Stimulus response of photopolymerized 1% and 0.5% N,N′‐methylene bisacrylamide (MBA) crosslinked 10% polyacrylamide (PAAm) hydrogels was studied in nitric acid. The hydrogels swelled exponentially to saturation in 13 h due to the osmotic pressure arising from diffusion of ions in to the gel. MBA (0.5%) gels swell more with larger time constant than 1% MBA gels due to lower bulk modulus. Diffusion coefficient of nitric acid in the hydrogel and polymer‐solvent interaction parameter were estimated from the swelling behavior and discussed. At longer times, the hydrogels deswelled linearly in nitric acid due to molecular modification of amide group by acidic hydrolysis. Degree of swelling and deswelling increase with nitric acid concentration. Raman and FTIR investigations revealed the formation of carboxylic acid due to acidic hydrolysis. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 710–720, 2008     

离子键交联的聚两性电解质凝胶在不同pH和不同电解质溶液中溶胀行为研究

以丙烯酸(AA)和甲基丙烯酸二乙氨基乙酯(DEAM)形成的离子复合物与丙烯酰胺(AAm)共聚,合成了一种新型的离子键交联的聚两性电解质凝胶(PADA).由于分子之间的氢键作用,PADA凝胶并不是在A/C(负正离子单体摩尔比)为1,而是在A/C为1.55处有最大消溶胀.与共价键交联的聚两性电解质凝胶相比,PADA凝胶的溶胀行为具有更强的pH敏感性.PADA凝胶在不同pH缓冲溶液中的溶胀行为表明,在pH 3~4之间消溶胀程度最大.在偏离该pH区域时凝胶均发生溶胀.但凝胶的溶胀程度在pH<3的酸性溶液中随A/C的增加而降低;而在pH>4的偏碱性溶液中随其增加而增加.在不同价数的离子溶液中,离子浓度对于PADA凝胶的平衡溶胀有着不同的影响.对于一价的NaCl溶液,PADA凝胶有典型的反聚电解质效应.但对于高价的CaCl2和柠檬酸三钠溶液,只在较低的浓度下,才表现出反聚电解质效应.而在较高盐浓度时,随盐浓度的增加其溶胀比反而降低.这可能与高价离子形成的离子键交联有关.与pH对PADA凝胶溶胀程度的影响相似,在CaCl2溶液中,PADA凝胶的溶胀程度随A/C的增加而降低;而在柠檬酸三钠溶液中则刚好相反.这种独特的溶胀行为似乎与高价离子电荷的正负性有关.     

P(AA-DAC)两性聚电解质水凝胶的合成及性质

以丙烯酸(AA)和丙烯酰氧乙基三甲基氯化铵(DAC)为单体, 采用水溶液聚合法制备了P(AA-DAC)聚电解质水凝胶. 采用红外光谱和核磁共振等方法对其结构进行了表征. 研究了不同组成比的聚电解质水凝胶在去离子水、不同pH值溶液以及不同离子强度盐溶液中的溶胀行为. 研究结果表明, 摩尔比为1∶1的聚电解质水凝胶表现出典型的两性聚电解质凝胶的溶胀行为. 离子强度对其溶胀行为有着显著影响, 在溶液离子强度较高时, 凝胶网络的溶胀主要受溶剂向凝胶内部扩散所控制, 满足Fick型扩散规律n≤0.5, 随着溶液离子强度的增加, 凝胶网络平衡含水量增加, 扩散系数增大.     

Adsorption of Apollo reactive dyes on poly(N,N dimethylamino ethylmethacrylate) hydrogels

Poly(N,N-dimethylamino ethylmethacrylate) [P(DMAEMA)] hydrogels were prepared by irradiating the ternary mixtures of dimethylamino ethylmethacrylate (DMAEMA)/ethyleneglycol dimethacrylate (EGDMA)/water (H₂O) by γ-rays at ambient temperature. The swelling of four types of DMAEMA hydrogels in distilled water is higher than the swelling of these hydrogels in dye solutions. The value of equilibrium swelling of P(DMAEMA)1 hydrogel was 338% at pH 7.0 in distilled water, while it was 325% and 326% at pH 7.0 in Apollofix Red (AR) and Apollofix Yellow (AY) solutions, respectively. The adsorption capacity of P(DMAEMA)1 hydrogel was found to increase from 85 to 131 mg for AR g⁻¹ dry gel and from 58 to 111 mg for AY g⁻¹ dry gel with decreasing pH of the dye solutions.     

Adsorption of Uranyl Ions into Poly(Acrylamide‐co‐Acrylic Acid) Hydrogels Prepared by Gamma Irradiation

Acrylamide (AAm)/Acrylic Acid (AAc) copolymers have been prepared by gamma irradiation of binary mixtures at three different compositions where the acrylamide/acrylic acid mole ratios varied around 15, 20, and 30%. Threshold dose for 100% conversion of monomers into hydrogels was found to be 8.0 kGy. Poly(Acrylamide‐co‐Acrylic Acid) (poly(AAm‐co‐AAc)) hydrogels have been considered for the removal of uranyl ions from aqueous solutions. Swelling behavior of these hydrogels was determined in distilled water at different pH values and in aqueous solutions of uranyl ions. The results of swelling tests at pH 8.0 indicated that poly(AAm‐co‐AAc) hydrogel, containing 15% acrylamide showed maximum % swelling. Diffusion of water and aqueous solutions of uranyl ion into hydrogels was found to be non‐Fickian in character and their diffusion coefficients were calculated. The effect of pH, composition of hydrogel, and concentration of uranyl ions on the adsorption process were studied at room temperature. It was found that one gram of dry poly(AAm‐co‐AAc) hydrogel adsorbed 70–320 mg and 70–400 mg uranyl ions from aqueous solutions of uranyl nitrate and uranyl acetate in the initial concentration range of 50–1500 mg UO₂ ²⁺L^?, depending on the amount of AAc in the hydrogels, respectively. Adsorption isotherms were constructed for poly(AAm‐co‐AAc)–uranyl ion system indicating an S type of adsorption in the Giles classification system. It is concluded that crosslinked poly(AAm‐co‐AAc) hydrogels can be successfully used for the removal of uranyl ions from their aqueous solutions.