2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.      

Synthesis of SnO<Subscript>2</Subscript> nanopowders by a sol-gel process using propanol-isopropanol mixture

A simple sol-gel process is proposed for synthesizing SnO₂ nanopowders utilizing normal propanol and isopropanol mixture instead of just using normal alcohols such as ethanol, propanol or butanol for Sol preparation. No surfactant was used in this Sol preparation process. The structure of sol is studied by FT-IR-ATR technique. On altering propanol to isopropanol ratio, three different nanopowders were obtained. X-ray powder diffraction, high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction pattern (SAED) and BET techniques were used to characterize prepared powders. Results show that smaller grain size was obtained via altering alcohols ratio. In addition, Merck commercial SnO₂ powder was also used as a reference material for comparing purposes; because it has nanometer scale (ca. 60 nm). HRTEM images show that obtained nanopowders were polycrystalline and their average diameters fall into the range of 6–80 nm. Finally, the effect of alkoxide ligand size through sol-gel synthesis on product particle size is discussed.      

Hydrogen sorption characteristics of magnesium-based composites with addition of Mg<Subscript>2</Subscript>Ni<Subscript>0.7</Subscript>Co<Subscript>0.3</Subscript> and graphite

Magnesium-based composites of 75 wt% Mg — (10, 15, 20) wt% Mg2Ni0.7Co0.3 — (15, 10, 5) wt% C mechanically activated for 30 min under argon in a planetary mill, were obtained. Their absorption-desorption characteristics were investigated under a pressure P = 1 MPa and temperatures of 623, 573, 473, 423 and 373 K. Desorption was carried out at 623 K and 573 K and a pressure of 0.15 MPa. All the three composites showed improved hydriding kinetics as compared to pure magnesium. However, the desorption temperature was somewhat higher than needed for practical application.      

Calorimetric study of melts in the System KF - K<Subscript>2</Subscript>NbF<Subscript>7</Subscript>

The relative enthalpies of melts in the system KF - K₂NbF₇ were measured by drop-calorimetry at the temperatures 1058, 1140 and 1208 K as a function of composition. Heat capacities of melted mixtures and enthalpies of mixing were determined using the experimental data. The molar heat capacity of melts diverges slightly from additivity. The molar enthalpy of mixing of melts shows small negative deviation from ideality which decreases with decreasing temperature. The thermal effect at mixing was assigned predominantly to association reactions producing more complex fluoroniobate anions.      

Synthesis of dibromo ketones by the reaction of the environmentally benign H<Subscript>2</Subscript>O<Subscript>2</Subscript>-HBr system with oximes

It was found that oximes undergo deoximation in the presence of the H₂O_2aq-HBr_aq system to form ketones and bromo ketones. This reaction provided the basis for the synthesis of dibromo ketones in yields varying from 40% to 94%. This method is environmentally friendly, sustainable, and easy to perform. The results of this investigation extend the potential of the use of oximes for the protection of carbonyl group, thus offering the ability to perform not only conventional deoximation but also the subsequent bromination of ketones. The reaction is easily scaled up and dibromo ketones can be prepared in gram amounts.      

Temperature effect over structure and photochemical properties of nanostructured SnO<Subscript>2</Subscript> powders

We successfully synthesized tin dioxide nanoparticles with polyhedral morphology via an ethylene glycol assisted sol-gel approach. The structural characteristics of three tin dioxide samples were investigated after being thermally treated at 400°C, 600°C and 800°C. X-ray diffraction (XRD) patterns clearly show the formation of single phase tin dioxide nanoparticles, with crystallite size of 6–20 nm, in good correlation with Fourier transform infrared (FTIR) spectra. Transmission electron microscopy (TEM) analysis confirms the formation of 6nm polyhedral nanoparticles for the 400°C sample. Ultraviolet-visible (UV-Vis) and photoluminescence (PL) spectra suggest a high concentration of oxygen vacancies. The oxygen vacancy concentration increases with temperature, due to the combined action of the formation of V_O and the energetic O compensation. X-ray photoelectron spectroscopy (XPS) analysis also confirms the formation of single phase tin dioxide and the presence of oxygen vacancies in good agreement with UV-VIS and PL data.

Open image in new window

     

Methylcellulose/SiO<Subscript>2</Subscript> hybrids: sol-gel preparation and characterization by XRD,FTIR and AFM

Methylcellulose (MC) / SiO₂ organic / inorganic hybrid materials have been prepared from MC and methyltriethoxysilane or ethyltrimethoxysilane, and characterized by XRD, FTIR and AFM. XRD showed peak shifts. FTIR shows intermolecular hydrogen bonding between MC and SiO₂. AFM depicts surface roughness which depends on the silica precursor and MC content.      

Controlled synthesis,characterization and thermal properties of Mg<Subscript>2</Subscript>B<Subscript>2</Subscript>O<Subscript>5</Subscript>

Optimum conditions for synthesizing monoclinic and triclinic Mg₂B₂O₅ compounds by high-temperature solid-state reactions were investigated. Mixtures composed of boric acid and magnesium oxide at MgO:B₂O₃ mole ratios of 1:0.25, 1:0.5 and 1:1.5 were heated for 1 hour at temperatures between 600–1050°C and the formed phases were identified by XRD analysis. Monoclinic Mg₂B₂O₅ was formed by heating at 850°C for 4 hours together with minimum amounts of triclinic Mg₂B₂O₅, while triclinic Mg₂B₂O₅ was formed as a single phase at 1050°C for the same reaction time. The products obtained at optimum conditions were subjected to a series of tests to determine their chemical compositions, particle size distributions, surface area values, IR spectra and TG/DTA patterns.      

The crystal structure of Ho<Subscript>4</Subscript>Ni<Subscript>11</Subscript>In<Subscript>20</Subscript>

The polycrystalline Ho₄Ni₁₁In₂₀ was obtained by arc-melting of the elements. The subsequent high temperature procedure was used for single crystal growth. Crystal structure of the compound was investigated by X-ray single crystal method: U₄Ni₁₁Ga₂₀ type, C 2/m, a = 22.4528(17), b = 4.2947(3), c = 16.5587(13) Å, β = 124.591(5)°, R1 = 0.0276, wR2 = 0.0493 for 1989 independent reflections with [I>2σ(I)].The structure is composed of three-dimensional network from Ni and In atoms in which Ho atoms fill distorted pentagonal channels. Open image in new window     

A green chemical route for the synthesis of Mn3O4 nanoparticles

A novel environmental friendly, room temperature route using an ionic liquid 1-n-butyl-3-methylimidazolium hydroxide ([BMIM]OH) for the synthesis of Mn₃O₄ nanoparticles is presented. The product was characterized using Fourier transform infrared spectroscopy, X-ray powder diffraction, and transmission electron microscopy. Phase purity was confirmed by XRD, and X-ray line profile fitting determined a crystallite size of 42 ± 11 nm. TEM analysis revealed various morphologies. EPR measurements have indicated the existence of long-range interactions, due to the wide range of particle sizes and morphologies observed.      

Molecular dynamics simulation study of the diamond D<Subscript>5</Subscript> substructures

Diamond D₅ is the name proposed by Diudea for hyper-diamonds having their rings mostly pentagonal. Within D₅, in crystallographic terms: the mtn structure, known in clathrates of type II, several substructures can be defined. In the present work, the structural stability of such intermediates/fragments appearing in the construction/destruction of D₅ net was investigated using molecular dynamics simulation. Calculations were performed using an empirical many-body potential energy function for hydrocarbons. It has been found that, at normal temperature, the hexagonal hyper-rings are more stable while at higher temperature, the pentagonal ones are relatively more resistant against heat treatment.      

Influence of ThO<Subscript>2</Subscript> on the photocatalytic activity of TiO<Subscript>2</Subscript>

Microcomposites consisting of TiO₂ (or Ce-doped TiO₂) and ThO₂ (0.5–2% of the TiO₂ mass) are produced by sol-gel synthesis of TiO₂ in presence of ThO₂. X-ray diffraction study reveals the effects of ThO₂ (compared to the ThO₂-free TiO₂, obtained by the same method) on the anatase interplanar distances, crystallites size and phase composition. The photocatalytic tests in presence of the composites under UV irradiation reveal an increase of the Malachite Green degradation rate constant. The effect depends on the Th relative content, temperature of annealing of the catalyst and addition of other doping agent. The highest photocatalytic activity is observed for TiO₂ obtained at 550°C and containing 1% ThO₂. The composite exhibits activity in dark, also. The presence of Ce⁴⁺ ions is not an obligatory requirement for the realization of the ThO₂ effect. The reported results suggest that the radioactivity of the Th and/or its decay products is one of the main factors responsible for the increased photocatalytic activity of TiO₂.      

Low temperature synthesis and characterization of Mn3O4 nanoparticles

Heating hydrous manganese (II) hydroxide gel at 85 °C for 12 hours produces Mn₃O₄ nanoparticles. They were characterized by X-ray powder diffraction (XRD) and infrared spectroscopy (FTIR). The particle size estimated from the SEM and X-ray peak broadening is approximately 32 nm, showing them to be nanocrystalline. EPR measurements confirm a typical Mn²⁺signal with a highly resolved hyperfine structure.      

Preparation and characterization of high specific surface area Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> from electrolytic manganese residue

Mn₃O₄ powders have been produced from Electrolytic Manganese Residue (EMR). After leaching of EMR in sulfuric acid, MnSO₄ solution containing various ions was obtained. Purifying the solution obtained and then adding aqueous alkali to the purified MnSO₄ solution, Mn(OH)₂ was prepared. Two methods were employed to produce Mn₃O₄. One way was oxidation of Mn(OH)₂ in aqueous phase under atmosphere pressure to obtain Mn₃O₄. The other way was roasting Mn(OH)₂ precursors in the range of 500°C to 700°C. The prepared samples were investigated by using several techniques including X-ray powder diffraction (XRD), Fourier Transformation Infra-Red (FTIR) spectra, and Brunauer-Emmett-Teller (BET) specific surface area instrument. Particle distribution and magnetic measurements were carried out on laser particle size analyzer, vibrating sample magnetometer (VSM). Through XRD, FTIR and determination of total Mn content (TMC), the products prepared were confirmed to be a single phase Mn₃O₄. BET specific surface areas can reach to 32 m² g⁻¹. The results indicated that products synthesized by aqueous solution oxidation method had higher specific surface areas and smaller particle size than those prepared by means of roasting. However the products prepared using the above two methods showed no obvious differences in magnetic property.      

Simultaneous displacement of a nitro group during coupling of diazotized <Emphasis Type="Italic">o</Emphasis>-nitroaniline with phenols

During the diazo-coupling reaction, nucleophilic displacement of a nitro group was also observed. This was the main reaction (1→7) when the starting amine bore either a chlorine or methoxy group at the para position (1b–c). The newly prepared compounds (7) might serve as convenient building blocks in synthesis of some heterocycles.      

Aminophosphine complex as a catalyst precursor in Suzuki coupling reactions

A palladium complex with an aminophosphine ligand has been prepared and investigated as a catalyst precursor in Suzuki coupling reactions in toluene. Nanoparticles composed of elemental palladium have been isolated from the reaction media and analyzed using transmission electroscopic microscope (TEM), which shows the essential catalysts palladium nanoparticles to have a size of ca. 3.0 nm. dedicate to the 60th birthday of Prof. Dr. Yuan Kou     

Determination of europium by using the chemical oscillating system of Ce(IV)-KBrO<Subscript>3</Subscript>-acetone-oxalic acid-H<Subscript>2</Subscript>SO<Subscript>4</Subscript>

A sensitive and convenient method for the determination of trace europium ions using an oscillating chemical reaction involving Ce(IV) - KBrO₃ - acetone - oxalic acid - H₂SO₄ was proposed. The results indicated that the changes in oscillating period (T) was linearly proportional to the negative logarithmic concentration of Eu³⁺ (-log C) in the range of 1.41 × 10⁻⁸ ˜ 1.41 × 10⁻⁴ mol L⁻¹ (r = 0.9982) with a detection limit of 1.04 × 10⁻⁹ mol L⁻¹. The recoveries were limited to the range of 99.5% to 100.8%. Under the same conditions, other rare earth ions did not interfere with the determination of Eu³⁺. In addition, a perturbation mechanism was also discussed briefly.      

Removal of cadmium and copper ions by <Emphasis Type="Italic">Trichosporon cutaneum</Emphasis> R57 cells immobilized onto polyvinyl alcohol/tetraethoxysilane hybrid matrices

Polyvinyl alcohol (PVA) and tetraethoxysilane (TEOS) hybrid materials were prepared by sol-gel methods and tested as matrices for immobilization of Trichosporon cutaneum R57, capable of removing cadmium and copper ions from aqueous solutions. A kinetic model was applied and the effects of matrix TEOS content on the copper and cadmium uptake equilibria and rate constants were investigated.      

Silver nanoparticles: synthesis through chemical methods in solution and biomedical applications

Chemical methods provide an easy way to synthesize silver nanoparticles (Ag NPs) in solution. These metal nanoparticles have a great potential for biomedical applications as an antibacterial, antifungal, and antiviral agent or in wound healing. The adjustment of the parameters involved in these reactions permits a precise control over the size, shape, monodispersity, and the surfaces of the nanoparticles. These nanoparticles are being used in the design of new hybrid organic-inorganic or inorganic nanomaterials for biomedical applications.