ZnO nanorods decorated calcined Mg–Al layered double hydroxides as photocatalysts with a high adsorptive capacity

The nanocomposites of magnesium–aluminium–carbonate–layered double hydroxides (Mg–Al–CO₃–LDHs) and ZnO nanorods were prepared via a homogeneous precipitation process. The presence of ZnO nanorods made the calcined Mg–Al–CO₃–LDHs, the strong adsorptive adsorbents for anions, have a photocatalytic activity. Both Mg–Al–CO₃–LDHs and the nanocomposites with various ZnO/Mg–Al–CO₃–LDHs mass ratios from 0.5:1 to 3:1 were characterized by X-ray diffraction, transmission electron microscope and UV–vis diffuse reflectance spectra. The nanocomposites quickly adsorbed the anionic dyes such as acid red G (ARG) without the light illumination, and the adsorbed dyes on the recovered nanocomposites were then degraded in a separated photocatalytic reactor. The adsorption ability of the nanocomposites and their photocatalytic activities for the removal of ARG were evaluated by the Fourier transform infrared spectra and UV–vis extinction spectra. The sample at 3:1 ZnO/Mg–Al–CO₃–LDHs mass ratio was shown to have higher photocatalytic efficiencies.     

Liquid-liquid equilibria of polyrotaxane and poly(vinyl alcohol)

Liquid–liquid equillibria (LLE) of the tertiary system of hydroxypropylated polyrotaxane (HPPR)–poly(vinyl alcohol) (PVA)–solvent have been investigated by focusing on the internal structures of HPPR–PVA blend gels. The phase diagrams of the HPPR–PVA aqueous systems displayed two liquid phases at a high concentration and molecular weight of PVA. This result was consistent with the prediction of the Flory–Huggins lattice model. On the contrary, the HPPR–PVA–DMSO system exhibited only a single phase. The HPPR–PVA blend gels crosslinked in dimethylsulfoxide (DMSO) were highly transparent over a wide concentration range, while the gels prepared in water were opaque at high polymer concentrations. Spherical domains were observed in the opaque gels by laser scanning confocal microscopy, and the sizes of the domains were significantly dependent on the amount of cross-linking reagent utilized. These results indicated that the transparency of the HPPR–PVA blend gels was strongly affected by the competition between the liquid–liquid two-phase separation and the crosslinking HPPR and PVA polymers during the preparation of the blend gels.     

A simultaneous TG–DTA study of the thermal decomposition of 2-hydroxybenzoic acid, 2-carboxyphenyl ester (salsalate)

Simultaneous thermogravimetry–differential thermal analysis (TG–DTA) and gas and liquid chromatography with mass spectrometry detection have been used to study the kinetics and decomposition of 2-hydroxybenzoic acid, 2-carboxyphenyl ester, commercially known as salsalate. Samples of salsalate were heated in the TG–DTA apparatus in an inert atmosphere (100 ml min⁻¹ nitrogen) in the temperature range 30–500 °C. The data indicated that the decomposition of salsalate is a two-stage process. The first decomposition stage (150–250 °C) had a best fit with second-order kinetics with E_a=191–198 kJ/mol. The second decomposition stage (300–400 °C) is described as a zero-order process with E_a=72–80 kJ/mol. The products of the decomposition were investigated in two ways:

(a)Salsalate was heated in a gas chromatograph at various isothermal temperatures in the range 150–280 °C, and the exit gas stream analyzed by mass spectrometry (GC–MS). This approach suggested that salsalate decomposes with the formation of salicylic acid, phenol, phenyl salicylate, and cyclic oligomers of salicylic acid di- and tri-salicylides.

(b)One gram samples of salsalate were heated in a vessel under nitrogen to 150 °C, and the residues were analyzed by liquid chromatography–mass spectrometry (LC–MS). The major compound detected was a linear tetrameric salicylate ester.

     

Trace element determination in seawater by ICP-SFMS coupled with a microflow nebulization/desolvation system

Direct and simultaneous determination of Al, Ag, As, Cd, Co, Cr, Cu, Fe, Mn, Mo, Pb, Sb, U, V and Zn in diluted (1:10 v:v) seawater from the Antarctic Ocean and the Venice Lagoon at the ng mL^–1 and pg mL^–1 level has been performed by using an inductively coupled plasma sector field mass spectrometer (ICP-SFMS). Samples were analysed by using a PFA microflow nebulizer coupled with a desolvation system or a PFA microflow nebulizer coupled with a Teflon spray chamber, respectively. Measurements were carried out at low (LR, m/m=300), medium (MR, m/m=3,000) and high (HR, m/m=7,500) resolutions depending on the studied isotope. To avoid contamination, sample pre-treatment was carried out in a clean laboratory equipped with a Class 100 vertical laminar flow hood. Concentration ranges (minimum–maximum in ng mL^–1) found in the Antarctic seawater samples (in depth profiles) were: Ag 0.0004–0.0018, As 0.69–1.32, Cd 0.031–0.096, Co 0.018–0.065, Cr 0.18–0.46, Cu 0.04–1.58, Fe 0.13–1.63, Mn 0.02–0.12, Mo 5.97–12.46, Pb 0.007–0.074, Sb 0.033–0.088, U 0.5–1.9, V 0.6–2.5 and Zn 0.16–0.80. Concentration ranges (min–max in ng mL^–1) found in the Venice Lagoon water samples (temporal profile from a benthic chamber experiment) were: Al 0.24–0.61, Ag 0.007–0.031, As 1.42–2.27, Cd 0.050–0.182, Co 0.440–1.461, Cr 0.15–0.34, Cu 0.81–2.46, Fe 0.25–1.66, Mn 11.6–31.7, Mo 6.50–10.6, Pb 0.047–0.225, Sb 0.240–0.492, U 1.7–3.3, V 1.3–2.8 and Zn 5.20–21.5. The detection limits range between 0.06 pg mL^–1 for Ag and U to 15 pg mL^–1 for Fe. In order to check the accuracy of the analytical procedure, measurements of the trace elements in a certified reference material (coastal Atlantic seawater, CASS-4-NRCC) were compared with the certified values. In addition, the results from the Antarctic and Venice Lagoon samples were compared with those obtained by using different analytical techniques.     

Neutron Activation Analysis of Bottom and Fly Oil Ash Leachates

Seven samples of oil fly and bottom ashes were leached with water using a Canadian standard test method for shake extraction of solid waste. The concentrations of 20 elements in the leachates were determined by the computerized systematic instrumental absolute neutron activation analysis. The ranges of concentrations (in ppm) found for the elements in the leachates were: Al (3–526), Ba (0.5–6), Ca (100–695), Cl (13–59), Co (1–6.3), Cr (0.2–6.6), Cs (0.03–0.4), Eu (0.003–0.01), Fe (28–690), K (42–464), La (0.3–49), Mg (214–3150), Mn (1.2–20), Na (88–4050), Sb (0.04–0.4), Sc (0.003–0.07), Sr (1.2–23), U (0.07–1), V (1.2–4540) and Zn (2.3–200). These findings were compared with the maximum concentrations allowed for these elements by Canadian regulations. The concentrations of Cr and U were found to be higher than their permissible limits on 7 occasions. The purpose of this study was to determine the background levels of different elements in oil ash leachates, in order to evaluate their potential impact on underground water.     

Preconcentration and XRF-determination of heavy metals in hair from Sudanese populations

Energy-dispersive X-ray fluorescence analysis was applied for the analysis of hair. The hair samples were digested in a mixture of nitric and perchloric acid and the heavy metals were precipitated with ammonium pyrrolidine dithiocarbamate. The accuracy, precision and recovery of the method for the elements Fe, Ni, Cu, Zn and Pb were evaluated through the analysis of a standard hair sample. The procedure was applied to the analysis of hair from an occupationally exposed group of Sudanese workers and a control group. The hair of the exposed group showed a range of 80–550 ppm Fe, 6–12 ppm Cu, 57–190 ppm Zn and 70–3700 ppm Pb, while that of the control group had a range of 60–310 ppm Fe, 7–22 ppm Cu, 89–170 ppm Zn and 3–17 ppm Pb.     

Oxidation at a sol-gel composite electrode doped with a dirhodium-substituted polyoxometalate for amperometric detection of peptides separated by HPLC

Oxidation of a variety of compounds, including methionine (Met), using a complex formed between dirhodium(II) acetate and the lacunary form of phosphotungstic acid as the catalyst is effective over a wide range of conditions, including pH 2–10. Thus, amperometric detection at a composite in which this complex is immobilized in a sol–gel material does not place restrictions on selection of conditions for separations by reverse-phase HPLC. A demonstration of this point is shown by a study of Met, Met–Phe, Phe–Met, Met–Met, and Gly–Met–Gly (Phe, phenylalanine; Gly, glycine). Using a 0.05 M phosphate buffer at pH 6.7, a C18 column, and a flow rate of 1 ml min⁻¹, capacity factors for Met, Gly–Met–Gly, Met–Met, and Phe–Met were 1.4, 2.1, 5.6, and 34, respectively. Phe–Met and Met–Phe co-eluted.     

Vibrational frequencies and structural determination of 1,3-difluoro-1,2-propadiene

The normal mode frequencies and corresponding vibrational assignments of 1,3-difluoro-1,2-propadiene in are examined theoretically using the GAUSSIAN 98 set of quantum chemistry codes. All normal modes were successfully assigned to one of eight types of motion (CC stretch, C–H stretch, C–F stretch, H–C–F scissors, H–C–F wag, H–C–F rock, H–C–F twist, and CCC bend) predicted by a group theoretical analysis. Comparing the vibrational frequencies with IR and Raman spectra available in the literature, a set of scaling factors are derived. Predicted infrared and Raman intensities are reported.     

Determination of methylmercury fluxes across the air–water and air–soil interfaces by gas chromatography with electron capture detection

A method for the determination of methylmercury (MeHg) fluxes across the air–water and air–soil interfaces was developed using an in situ chamber. The MeHg in the air coming out of the chamber was captured by a column containing sulfhydryl cotton fiber adsorbent. MeHg was then desorbed from the column by using 2 mol L^–1 HCl. The MeHg in the effluent was extracted with benzene, and determined by gas chromatography with electron capture detection. Finally, the MeHg flux was calculated using the chamber. The method was applied to simulated experiments, and the results showed that the MeHg fluxes in the air–water system were higher than those in the air–soil–water system. The method was also successfully applied to the field measurements of an environment polluted by a chemical factory, and the results showed that the MeHg fluxes across the air–soil and air–water interfaces were 0.21–3.09 and 0.14–0.79 ng m^–2 h^–1, respectively. The method will be a useful tool in the environmental study of MeHg.     

Petrographic/geochemical studies of primary and alteration–weathering minerals in garnetiferous ultramafic xenoliths–basanite, Tartous Province, NW Syria

Kimberlitic–pyropic peridotite–xenolites, probably of Jurassic–Cretaceous age, were found mixed with a younger Upper Tertiary basanitic diabase, as flow texture of plagioclase laths and ilmenite rods around those xenoliths indicated. Mafic–ultramafic rocks were crushed, sheared, and cropped along a creek about 15–18 km NE of the town of Dreikeesh, NW Syria. ⁴⁰K–⁴⁰Ar isotopic dating of a pure fresh black cpx sample, collected from the peridotite xenoliths, yielded an age of about 70 Ma. This age is concurrent to the time when Africa, Eurasia, and America were part of the super continent Pangaea. It also suggests that kimberlite–pyropic peridotitic rocks were located within a cratonic pipe prior to their 2000-km eastward journey (starting from the Mid-Atlantic Rift). Sampled outcrops were located within a ring of about 40 km diameter, considered to be a dome consisting of one or more clusters of kimberlitic pipes. The dome structure, mostly covered with Upper Jurassic–Cretaceous carbonate beds, was tilted westward, and rifted and sheared along its eastern edge. Tilting and crushing were accomplished after the opening of the Red Sea in the Miocene, and the counterclockwise movements of the Arabian plate, which folded the carbonate beds to form the N–S-trending Alawite mountain range along the Syrian coast. Olivine, cpx, and pyrope were the major phases in peridotite. Pyrope, including its Cr–Ni-contents, was found to be the best indicator to decipher the temperature–pressure (T–P) conditions for the system. The inferred temperature was found to be about 1460 °C, at a pressure of 62 kb (around 207 km-depth). Petrographic studies revealed many zoned, resorbed, octahedral and non-metasomatized tiny grains, associated with partly to wholly metasomatized and iddingsitized olivines.     

Characterization of low-molecular weight peptides in champagne wine by liquid chromatography/tandem mass spectrometry

This paper reports the use of an on-line LC–ESI–MS/MS method for the identification and quantification of di- and tripeptides in champagne wine without laborious sample pretreatment. The identification of these compounds, in their underivatised form, is based on identical retention times and ESI–MS spectra to those of reference standards. The presence of nine dipeptides (Arg–Ile, Ile–Arg, Ile–Val, Lys–Phe, Lys–Tyr, Phe–Lys, Tyr–Gln, Tyr–Lys, Val–Ile) and the absence of two tripeptides (Phe–Arg–Arg and Lys–Met–Asn) have been evidenced in the matrix. Calibration curves for each analyte were established using Phe–Arg as internal standard. The calibration curves were linear in the concentration range 0.1–10 mg L⁻¹ with a determination coefficient, r², better than 0.992. The accuracy for the calibration standard was estimated at between 92 and 102%. This method allows high recovery and satisfies the necessary requirements with respect to accuracy, repeatability and sensitivity. The first application of this analytical method to the measurement of di- and tri-peptides in different vintages of champagne wine is reported. Compositional changes in the peptides occurred depending on the vintage.     

Sizes and Conformation of the Molecules of DNA–Surfactant Complexes in Dilute Solutions and on the Atomic Smooth Substrates

The conformations of the molecules of DNA–surfactant complexes in dilute solutions and on the atomic smooth surfaces of mica and highly oriented pyrolytic graphite were comparatively studied by the methods of isothermal diffusion, electric birefringence, and atomic force microscopy. The DNA–surfactant complexes were deposited onto the substrates from a chloroform solution. The number of particles of the DNA–surfactant complex on the substrate was changed by varying the concentration of the initial solution within three orders of magnitude. The particles of a shape close to ellipsoidal, 25–70 nm in diameter and 2–4 nm high, were observed at the lowest concentration of DNA–surfactant solution on the mica substrate. The shape and size of these particles correspond to those of a single DNA–surfactant complex, calculated from its translational diffusion coefficient and the time of orientational relaxation in dilute solutions. An increase in the number of molecules deposited onto the substrate leads to an increase in the characteristic sizes of DNA–surfactant complex particles observed by the atomic force microscopy. This may be associated with the aggregation of DNA–surfactant complexes.     

Self-assembly and branching of sucrose stabilized silver nanoparticles by microwave assisted synthesis: From nanoparticles to branched nanowires structures

Silver nanostructures were synthesized under microwave irradiation from a solution of silver nitrate and sucrose, with any other reducing or capping agent. The size and morphology of nanostructures changed continuously during the irradiation time. The obtained nanostructures at the different irradiation time were characterized by X-Ray diffraction, UV–vis spectroscopy, scanning and transmission electron microscopy and selected area diffraction pattern. It was evidenced that initially Ag nanoparticles were formed, which, as reaction time elapsed, self-assembled and fused with each other to yield nanowires and further branched nanowires. The formation of the silver branched nanostructures can be explained as a process of initial reduction–nucleation–adsorption–growth–branching growth.     

Fabrication and electrochemical properties of novel ternary Sb–Co–P alloy electrodes for lithium-ion batteries

A novel ternary Sb–Co–P alloy electrode was prepared by electroplating on copper current collector as a promising negative electrode material for lithium-ion batteries. The structural and morphological features of the Sb–Co–P alloy were characterized by powder X-ray diffraction (XRD) and scanning electron microscope (SEM). The as-prepared alloy electrode exhibits a high specific capacity and an excellent cycleability. The initial discharge and charge capacities of the Sb–Co–P alloy anode were measured 700 and 539 mA h g⁻¹, respectively. The results suggest that the Sb–Co–P alloy material obtained by the electrodeposition shows a good candidate anode material for lithium-ion batteries.     

Vibrational frequencies and structural determinations of tetraisocyanatogermane

The normal mode frequencies and corresponding vibrational assignments of Ge(NCO)₄ are examined theoretically using the 98 set of quantum chemistry codes. Each of the vibrational modes was assigned to one of six types of motion predicted by a group theoretical analysis (Ge–N stretch, N–C–O symmetric stretch, N–C–O asymmetric stretch, N–C–O bend, Ge–N–C bend, and N–Ge–N bend) utilizing the T_d symmetry of the molecule. Uniform scaling factors were derived for each type of motion. Predicted infrared and Raman intensities are reported.     

Spectrophotometric determination of cationic and anionic surfactants with anionic dyes in the presence of nonionic surfactants,part II: Development of batch and flow injection methods

On the basis of the changes in absorption spectra of azo dyes on the addition of an organic onium ion, spectrophotometric methods for the determination of organic onium salts and anionic surfactants were developed, and applied to flow injection method. Propyl orange (PO^–) was used for the determination of organic onium ions. Pairs of PO^– and Zeph⁺ (tetradecyldimethyl-benzylammonium ion) or PO^– and nC₁₈TMA⁺ (n-octadecyltrimethylammonium ion) were used for the determination of anionic surfactants. The determination range of organic onium ions were (0–3) × 10^–5 M by a batch method and were (0–2) × 10^–5 M by a flow injection method. The determination ranges of anionic surfactants were (0–2) × 10^–5 M by the batch method, and were (0–5) × 10^–5 M by the flow injection method, and the detection limit corresponding toS/N = 3 was 3 × 10^–7 M by the flow injection method. By the proposed flow injection method, anionic surfactants in water samples were determined.     

Phase equilibria of the ternary system vinyl acetate/(R,S)-1-phenylethanol/carbon dioxide at high pressure conditions

Phase equilibrium measurements, correlations and predictions are presented for the binary systems (R,S)-1-phenylethanol/CO₂ and vinyl acetate/CO₂ and for the ternary system vinyl acetate/(R,S)-1-phenylethanol/CO₂. Experiments for the ternary system were performed in the temperature range of 323–343 K and in the pressure range of 7–12 MPa, using a high pressure phase equilibrium apparatus with a high pressure visual variable volume cell. Phase compositions were determined by taking samples of each phase and analysing them by gas chromatography. Equilibrium data were correlated with the Peng–Robinson equation of state combined with the Mathias–Klotz–Prausnitz mixing rule. A good correlation of both phases behaviour was obtained with an average absolute deviation (AAD) of 6.80%. Predictions for the binary sub-systems and for the ternary system were performed using the Peng–Robinson and the Soave–Redlich–Kwong equation of state, with the predictive mixing rule MHV1.     

Determination of Antimony in Environmental Samples by ETAAS Using Different Permanent Modifiers

Single noble metal permanent modifiers such as, Rh, Ir, and Ru, as well as mixed tungsten plus noble metal (W–Rh, W–Ru, W–Ir) permanent modifiers thermally deposited on the integrated platform of a transversally heated graphite atomizer (TGA) were employed for the determination of antimony in sludge, soil, sediment, coal, ash and water samples by electrothermal atomic absorption spectrometry (ETAAS).Microwave digests of solid samples and water samples were directly introduced into different pre-treated platforms of graphite tubes. The performance of the modifiers for accurate antimony determination in real samples depended strongly on the type of permanent modifier chosen. The single noble metal (Rh, Ir and Ru) permanent modifiers were suitable for analyte determinations in simpler matrices, such as waters (recoveries of certified values 95–105%), but the analyte recoveries of certified values in sludge, soil, sediment, coal, and ash samples were always lower than 90%. On the other hand, for the determination of antimony, using W–Rh, W–Ru, and W–Ir permanent modifiers presented recoveries of certified values within 95–105% for all the samples.Long-term stability curves obtained for the determination of antimony in environmental samples with different permanent modifiers (Rh, Ir, Ru, W–Rh, W–Ir, W–Ru) showed that the improvement in tube lifetime depends on the tungsten deposit onto the platform. The tungsten plus noble metal permanent modifier presents a tube lifetime of at least 40% longer compared to a single permanent modifier.     

Neutron activation analysis of asbestos from Canada

Concentrations of Al, Au, Br, Ce, Cl, Co, Cr, Fe, K, La, Mg, Mn, Na, Ni, Sb, Sc, Sm, Srm and V were determined in 6 samples of asbestos from Canada. They were equal to (in ppm): Al 1660–3430; Au 0.03–0.04; Br 3.1–11.7; Ce 1.7–4.8; Cl 116–331; Co 35–83; Cr 200–2060; Fe 29300–42200; K 125–867; La 0.28–1.03; Mg 24–25.9%; Mn 418–545; Na 364–1610; Sb 0.65–1.46; Sc 3.73–5.57; Sm 0.09–0.3; Sr 26.7–41.4; V 8.4–14.3. Five toxic elements were found in asbestos; Cr, Mn, Ni, Sb and V.     

Synthesis and absorption spectra of 3,5-diaryl-1,2,4-triazoles

1,2,4-Triazoles with symmetrical tolyl substituents were obtained from the corresponding 1,3,4-oxadiazoles by reaction with formamide and subsequent hydrolysis of the resulting formyl derivatives; 1,2,4-triazoles with unsymmetrical substituents were obtained from iminoesters and hydrazides of acids. A set of bands of the triazole ring at 1470–1480, 1390, 1270–1290, 1140–1150, and 725–750 cm^–1 and of NH vibrations at 2400–3200, 1580–1620, and 830–900 cm^–1 are characteristic for the IR spectra of these triazoles. The UV spectra of the triazoles are characterized by phenyl ring absorption at about 200 nm and a band of electron transitions between the phenyl and triazole rings at 230–290 nm.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 12, pp. 1682–1685, December, 1977.