基于层层自组装的CuTsPc/DPDCH纳米管的制备

在阳极多孔氧化铝模板中利用层层自组装技术制备出了高度有序的聚电解质磺化酞菁铜(CuTsPc)/4,4′-联吡啶盐酸盐(DPDCH)纳米管, 并对其组装过程用UV-Vis, XRD和FT-IR进行了分析, 纳米管的微观形貌通过SEM和TEM进行表征. 结果表明, 第一层 CuTsPc和第二层DPDCH在AAO模板上的沉积平衡时间均约为60 min, 沉积过程主要有三个阶段: 模板孔外的吸附过程、孔内扩散控制的沉积过程和孔内表面沉积控制过程. CuTsPc主要以磺酸根吸附于AAO模板上. CuTsPc/DPDCH纳米管为非晶态体系. CuTsPc/DPDCH纳米管的外径和壁厚分别为200和20 nm, 外径受控于AAO模板的孔径, 壁厚与组装的层数有关, 利用此方法还可以制备其他带有相反电荷的有机小分子对纳米管或纳米线.     

Preparation of Polyelectrolyte Nanotubes by a Pressure filter-template Technique Using Microporous Anodic Aluminum Oxide (AAO) as the Template

Polyelectrolyte nanotubes of poly(sodium 4‐styrene‐sulfonate) (PSS) with cationic poly(diallyl dimethyl ammonium chloride) (PDDA) (PSS/PDDA) were fabricated by a pressure‐filter‐template technique using microporous anodic aluminum oxide (AAO) as the template. UV‐Vis spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD) and infrared spectroscopy (FT‐IR) were applied to characterize the obtained PSS/PDDA nanotubes. The results have shown that the PSS/PDDA nanotubes exhibit an amorphous structure and have the outer diameter of 200 nm and length of 25 µm respectively, which are in good agreement with the dimensions of the AAO template pores. The wall thickness of the nanotubes may be controlled by the number of the self‐assembled layers. Formation of the nanotubes follows a layer‐by‐layer (LbL) mechanism due to the electrostatic interactions, where the SO^?₃ groups of PSS are first adsorbed on the Lewis acid sites of AAO template pores.     

Free-standing, erect ultrahigh-aspect-ratio polymer nanopillar and nanotube ensembles

Free-standing polymer (poly(methyl methacrylate) or cyclic olefin copolymer) nanopillar and nanotube ensembles with previously unreported, ultrahigh aspect ratios (300 to >1600) were fabricated via anodic aluminum oxide (AAO) template-based methods that utilize a dilute, aqueous H3PO4 template etchant followed by freeze drying removal of the aqueous medium. Good replication of the AAO template by either solutions of the polymeric materials or molten polymer was achieved by using ultrasonic degassing and vacuum conditions. Classical surface wetting and viscoelastic fluid rheology theories were applied to explain the formation of polymer nanopillars and nanotubes in the aluminum oxide templates. The utilization of dilute H3PO4 for etching the AAO template and freeze-drying removal of the environmental liquid allows for the preparation of free-standing, erect, and ordered polymeric nanopillars or nanotubes that show much promise for use in biological microelectromechanical systems that target biological analyses.     

氧化铝模板上定向纳米碳管的快速生长及超声切短

在阳极氧化铝（AAO）模板上电沉积催化剂,快速生长了定向纳米碳管,纳米碳管以顶部生长模式生长.采用了超声的方法来切短露头于AAO模板的纳米碳管,增加纳米碳管膜的定向性.结果显示随着超声时间的增加,纳米碳管的定向性增加.位于纳米碳管膜顶部的催化剂在碳管切短的同时被去除,得到了顶部开口的纳米碳管.解释了纳米碳管被超声切短的机理.     

Nanoporous carbon nanotubes synthesized through confined hydrogen-bonding self-assembly

We report a simple and direct synthetic method for the preparation of nanoporous carbon nanotubes with larger pores (>10 nm) on the tube wall. The method combines the use of anodic aluminum oxide (AAO) as a template for the tube diameter and block copolymer/carbohydrates self-assembly within thin films confined inside AAO pore channels to form nanopores. It involves coating the AAO inner pore channel surface with block copolymer (polystyrene-co-poly(vinylpyridine)) and carbohydrates in dimethylformamide (DMF) solution. Drying of DMF induced microphase separation of PS-PVP and formation of ordered PS and PVP/carbohydrate domains. Within the coating, the carbohydrates stay specifically only in the pyridine domains surrounding PS domains due to the hydrogen bonding between carbohydrates and pyridine blocks. After carbonization at high temperature (>460 degrees C) in argon, PS was removed, forming the nanopores and carbohydrates, and PVP was carbonized, forming the framework of nanoporous carbon tubes within AAO channels. Removal of AAO led to the formation of individual monodisperse nanoporous carbon nanotubes with a tube wall of approximately 16 nm. The ease with which these nanoporous carbon nanotubes can be fabricated, and the ability to tune tube nanostructures and surface chemistry through the choice of block copolymers used and carbonization temperature, should facilitate investigations of their scope for practical applications.     

Synthesis of Various Metal/TiO2 Core/shell Nanorod Arrays

We present a general approach to fabricate metal/TiO₂ core/shell nanorod structures by two-step electrodeposition. Firstly, TiO₂ nanotubes with uniform wall thickness are prepared in anodic aluminum oxide (AAO) membranes by electrodeposition. The wall thickness of thenanotubes could be easily controlled by modulating the deposition time, and their outer diameter and length are only limited by the channel diameter and the thickness of the AAO membranes, respectively. The nanotubes' tops prepared by this method are open, while the bottoms are connected directly with the Au film at the back of the AAO membranes. Secondly, Pd, Cu, and Fe elements are filled into the TiO₂ nanotubes to form core/shell structures. The core/shell nanorods prepared by this two-step process are high density and free-standing, and their length is dependent on the deposition time.     

化学修饰阳极氧化铝模板法合成小尺寸聚苯胺纳米线

利用表面活性剂对阳极氧化铝(AAO)模板进行化学修饰，发展了模板合成法，从而得到更小尺寸的聚苯胺纳米管、线.在表面活性剂十八烷基脂肪酸(R18)修饰下，在14 nm孔径的AAO模板中合成7 nm的纳米线.对不同表面活性剂的比较后发现,通过改变修饰表面活性剂上烷基链长可以对所制备的聚合物纳米管、线的直径进行调控.     

贫水电解质体系制备多孔阳极氧化铝模板的研究

在有机溶剂为主的含草酸电解质中,研究了大孔径有序度高的阳极氧化铝(AAO)的一步法电化学制备.实验证实,电解质中水含量的降低能够有效抑制铝的电氧化速率和溶解速率,使得其氧化膜孔道的生长能够稳定进行,所得到的六方孔道排列有序度明显高于纯水溶剂制备的电解质体系下的产物.考察了水含量、有机溶剂种类以及电解质浓度对AAO模板孔道形貌的影响.结果表明,有机溶剂贫水电解质体系使得电氧化电压的选取范围比水溶液电解质体系更宽,孔径连续可调,反应条件温和.该方法适合于制备均匀大孔径的AAO模板.     

Atomic layer deposition as pore diameter adjustment tool for nanoporous aluminum oxide injection molding masks

The wetting properties of polypropylene (PP) surfaces were modified by adjusting the dimensions of the surface nanostructure. The nanostructures were generated by injection molding with nanoporous anodized aluminum oxide (AAO) as the mold insert. Atomic layer deposition (ALD) of molybdenum nitride film was used to control the pore diameters of the AAO inserts. The original 50-nm pore diameter of AAO was adjusted by depositing films of thickness 5, 10, and 15 nm on AAO. Bis(tert-butylimido)-bis(dimethylamido)molybdenum and ammonia were used as precursors in deposition. The resulting pore diameters in the nitride-coated AAO inserts were 40, 30, and 20 nm, respectively. Injection molding of PP was conducted with the coated inserts, as well as with the non-coated insert. Besides the pore diameter, the injection mold temperature was varied with temperatures of 50, 70, and 90 degrees C tested. Water contact angles of PP casts were measured and compared with theoretical contact angles calculated from Wenzel and Cassie-Baxter theories. The highest contact angle, 140 degrees , was observed for PP molded with the AAO mold insert with 30-nm pore diameter. The Cassie-Baxter theory showed better fit than the Wenzel theory to the experimental values. With the optimal AAO mask, the nanofeatures in the molded PP pieces were 100 nm high. In explanation of this finding, it is suggested that some sticking and stretching of the nanofeatures occurs during the molding. Increase in the mold temperature increased the contact angle.     

大长径比有序多孔阳极氧化铝模板的制备及用于镍纳米线阵列

报道一种恒电流二次氧化制备大长径比(>1000)阳极氧化铝(AAO)模板的方法,研究氧化时间和氧化电流密度分别对制备的AAO模板的表面形貌、孔径大小、厚度等的影响.结果表明,AAO模板的表面形貌及厚度n受m氧、厚化度电约流为密2度00及μ氧m、化长时径间比的为影10响0;-当13氧00化的电高流质密量度A为AO8模m板A·.c采m用-2电时化,氧学化沉1积8方h能法在制制备备出的孔A径A为O模15板0-的20孔0中成功制备了Ni纳米线阵列,分别用扫描电镜(SEM)、高分辨透射电镜(HRTEM)、X射线衍射(XRD)和X射线能量散射光谱(EDS)对其进行了表征;结果显示,制备的Ni纳米线排列整齐有序,每根Ni纳米线直径几乎相同,约150nm,长度约为180-200μm,长径比为1200-1300,与AAO模板的参数一致.研究了Ni纳米线阵列的长径比对其磁性能的影响,发现大长径比的Ni纳米线阵列具有明显的磁各向异性,而长径比约为200的Ni纳米线阵列未表现出明显的磁各向异性.本文结果表明,恒电流二次氧化方法能制备大长径比的AAO模板,并能用于制备大长径比的一维纳米材料阵列,可望在制备具有特殊光学、磁学等性能材料方面得到应用.     

一种新的WO3纳米管的制备方法

一维纳米材料因可用来构造高性能纳米器件的结构单元而成为纳米材料研究的热点．目前的研究重点集中在材料的制备和结构性能表征方面,已发展了多种制备方法,主要有模板法、V-L-S法、L-L-S法和V-S法等,其中阳极氧化铝(AAO)模板法是制备一维材料的好方法．AAO模板的制备工艺已相当成熟,     

In situ synthesis and characterization of TiO<Subscript>2</Subscript> nanoarray films

Based on anodic aluminum oxide (AAO) templates prepared in different acidic solutions, highly ordered aligned titania nanotubes array films have been successfully prepared by the liquid phase deposition method. The effect of AAO template type on the microstructure of titania film have been studied. Using the template with a certain volume fraction of Al₂O₃ (less than 0.71), ordered aligned titania nanotubes were obtained, characterized with an outer diameter of 200 nm and an inner diameter of 100 nm, respectively. However, titania existed as ordered aligned nanorods with the diameter of 100 nm when the template with large volume fraction of Al₂O₃ (larger than 0.71) was used. TiO₂ thin films calcined at 400°C for 4 h have an anatase phase and exhibit good photocatalytic activity, i.e., 75% methylene blue could be degraded under ultraviolet irradiation for 2 h.     

模板合成法制备金纳米线的研究

近年来,利用化学和物理方法制备各种高度有序的纳米结构材料已经成为学术界的研究热点之一．其中,在特定的模板中沉积各种材料而构建纳米点阵的方法,具有制备简便,成本较低等优点,而且在尺度上可以突破刻蚀技术的局限性,具有广泛的应用前景［１］．常用的模板有阳极氧化多孔铝（ＡＡＯ）、多孔硅和聚合物等,其中ＡＡＯ模板具有耐高温,绝缘性好,孔洞分布均匀有序,而且大小可控等特点［２］,是使用较为广泛的一种．利用阳极氧化铝为模板,采用电化学方法［３～７］或压差注入法［８］制备有序的纳米粒子点阵,已经在润滑［９］、电…     

利用AAO模板合成纳米材料

利用AAO模板合成纳米材料;氧化铝;纳米结构;综述     

Preparation of well-aligned carbon nanotubes/silicon nanowires core-sheath composite structure arrays in porous anodic aluminum oxide templates

The well-aligned carbon nanotubes (CNTs) arrays with opened ends were prepared in ordered pores of anodic aluminum oxide (AAO) template by the chemical vapor deposition (CVD) method. After then, silicon nanowires (SiNWs) were deposited in the hollow cavities of CNTs. By using this method, CNTs/SiNWs core-sheath composite structure arrays were synthesized successfully. Growing structures and physical properties of the CNTs/SiNWs composite structure arrays were analyzed and researched by the scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction spectrum (XRD), respectively. The field emission (FE) behavior of the CNTs/SiNWs composite structure arrays was studied based on Fowler-Nordheim tunneling mechanism and current-voltage (/-V) curve. And the photoluminescence (PL) was also characterized. Significantly, the CNTs/SiNWs core-sheath composite structure nanowire fabricated by AAO template method is characteristic of a metal/semiconductor (M/S) behavior and can be     

Protein nanotubes with an enzyme interior surface

This report describes the synthesis and enzyme activities of multilayered protein nanotubes with an α-glucosidase (αGluD) interior surface. The nanotubes were prepared by using an alternating layer-by-layer (LbL) assembly of human serum albumin (HSA) and oppositely charged poly-L-arginine (PLA) into a track-etched polycarbonate (PC) membrane (pore size=400 nm) followed by addition of αGluD as the last layer of the wall. Subsequent dissolution of the PC template yielded (PLA/HSA)(2)PLA/αGluD nanotubes. SEM measurements revealed the formation of uniform hollow cylinders with (413±17) nm outer diameter and (52±3) nm wall thickness. In aqueous media, the nanotubes captured a fluorogenic glucopyranoside, 4-methyl-umbelliferyl-α-D-glucopyranoside (MUGlc), into their one-dimensional pore space and hydrolyzed the substrate efficiently to form α-D-glucose. We determined the enzyme parameters (Michaelis constant, K(M), and catalytic constant, k(cat), values) of the protein nanotubes. The several-micrometers-long cylinders were of sufficient length to be spun down by centrifugation at 4000 g, so the product could therefore be easily separated. Similar biocatalysts were prepared by complexation of biotinylated-αGluD into HSA-based nanotubes bearing a single avidin layer as an internal surface. The obtained hybrid nanotubes also exhibited the same enzyme activity for the MUGlc hydrolysis.     

4-(Dimethylamino)pyridine as a powerful auxiliary reagent in the electroless synthesis of gold nanotubes

Gold nanotubes of small particle sizes down to 5 nm and high aspect ratios were synthesized in ion track etched polycarbonate following a rational reaction design. 4-(Dimethylamino)pyridine (DMAP) was employed to adjust the electroless deposition by interfering with the autocatalytically active gold surface. Modification of the pH value and DMAP concentration led to a wide range of products which were characterized by SEM, TEM, and EDS. Filigree nanotubes of 10-15 nm wall thickness and 5.0 ± 2.1 nm grain size were obtained as well as robust and free-standing structures proving homogeneous deposition along the whole template length of 30 μm. Template-supported gold nanotubes were applied in the UV-vis monitored reduction of 4-nitrophenol by sodium borohydride under pseudo-first-order conditions. They proved to be a reliable microfluidic system of excellent catalytic activity coming up with an apparent rate constant of 1.3 × 10(-2) s(-1). Despite a high flow rate, the reaction showed 99% conversion after a distance of just 60 μm.     

Nanoparticle films as a conducting layer for anodic aluminum oxide template-assisted nanorod synthesis

A simple, inexpensive, and robust methodology was developed to fabricate conductive film substrates by mechanically packing nanoparticles (NPs) on one side of anodic aluminum oxide (AAO). Gold, silver NPs, and carbon nanotubes were used as building blocks in the synthesis of conductive film substrates, upon which perpendicular nanorod arrays and colloidal free-standing nanorods were easily constructed. Characterizations by field emission scanning electron microscopy (FE-SEM) and optical dark-field microscopy confirmed the validity of the conductive NP film substrates on the AAO template. This contribution could provide a convenient and low-cost means for the fabrication of various conductive substrates on AAO.     

低频交流电沉积金纳米线阵列的AFM研究

迄今,人们已采用许多方法制备纳米材料,如刻蚀技术、化学法和模板法等［1]．其中,引起科学界广泛兴趣的模板法,在合成有序纳米材料上占有极其重要的地位．常用的模板有两种,一种是有序孔洞阳极氧化铝（Anodic Aluminum Oxide,AAO）模板[2],另一种是含有孔洞无序分布的高分子模板．AAO模板具有耐高温,绝缘性好,孔洞分布均匀有序,而且大小可控等特点［3]．可以利用 AAO模板来制备各种纳米纤维和纳米管,如导电聚合物［4]、金属［5]、半导体［6]、碳［7]和其它一些材料．由于纳米材料的应用具有广阔的前景,如光催化、电化学、酶固定等方面,因而不同材料纳米线的制备备受关     

模板表面对间规聚苯乙烯在纳米模板中结晶取向的影响

以偏振显微红外光谱方法研究间规聚苯乙烯（sPS）在阳极氧化铝（AAO）模板孔洞内的结晶取向行为。 以正己基三甲氧基硅烷修饰AAO模板孔洞表面,使其烷基化,探索表面性质对不同尺寸孔洞内sPS结晶取向的影响。 结果表明,sPS在255 ℃温度下结晶,而且随孔洞尺寸的减小,纳米孔洞内sPS分子链的垂直取向程度均降低,并且相同孔径尺寸下在表面烷基化的孔洞内sPS晶区分子链的垂直取向程度更低。 这些现象可归因于分子链与孔壁间相互作用的不同导致孔壁表面对晶核取向的诱导。