Synthesis of poly(β‐pinene)‐g‐poly(meth)acrylate by the combination of living cationic polymerization and atom transfer radical polymerization

New graft copolymers of β‐pinene with methyl methacrylate (MMA) or butyl acrylate (BA) were synthesized by the combination of living cationic polymerization and atom transfer radical polymerization (ATRP). β‐Pinene polymers with predetermined molecular weights and narrow molecular weight distributions (MWDs) were prepared by living cationic polymerization with the 1‐phenylethyl chloride/TiCl₄/Ti(OiPr)₄/nBu₄NCl initiating system, and the resultant polymers were brominated quantitatively by N‐bromosuccinamide in the presence of azobisisobutyronitrile, yielding poly(β‐pinene) macroinitiators with different bromine contents (Br/β‐pinene unit molar ratio = 1.0 and 0.5 for macroinitiators a and b , respectively). The macroinitiators, in conjunction with CuBr and 2,2′‐bipyridine, were used to initiate ATRP of BA or MMA. With macroinitiator a or b , the bulk polymerization of BA induced a linear first‐order kinetic plot and gave graft copolymers with controlled molecular weights and MWDs; this indicated the living nature of these polymerizations. The bulk polymerization of MMA initiated with macroinitiator a was completed instantaneously and induced insoluble gel products. However, the controlled polymerization of MMA was achieved with macroinitiator b in toluene and resulted in the desired graft copolymers with controlled molecular weights and MWDs. The structures of the obtained graft copolymers of β‐pinene with (methyl)methacrylate were confirmed by ¹H NMR spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1237–1242, 2003     

2‐[(Diphenylphosphino)methyl]pyridine as ligand for iron‐based atom transfer radical polymerization

2‐[(Diphenylphosphino)methyl]pyridine (DPPMP) was successfully used as a bidentate ligand in the iron‐mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) with various initiators and solvents. The effect of the catalytic system on ATRP was studied systematically. Most of the polymerizations with DPPMP ligand were well controlled with a linear increase in the number‐average molecular weights (M_n) versus conversion and relatively low molecular weight distributions (M_w/M_n = 1.10–1.3) being observed throughout the reactions, and the measured molecular weights matched the predicted values. Initially added iron(III) bromide improved the controllability of the polymerization reactions in terms of molecular weight control. The ratio of ligand to metal influenced the controllability of ATRP system, and the optimum ratio was found to be 2:1. It was shown that ATRP of MMA with FeX₂/DPPMP catalytic system (X = Cl, Br) initiated by 2‐bromopropionitrile (BPN) was controlled more effectively in toluene than in polar solvents. The rate of polymerization increased with increasing the polymerization temperature and the apparent activation energy was calculated to be 56.7 KJ mol^?1. In addition, reverse ATRP of MMA was able to be successfully carried out using AIBN in toluene at 80 °C. Polymerization of styrene (St) was found to be controlled well by using the PEBr/FeBr₂/DPPMP system in DMF at 110 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2922–2935, 2008     

Synthesis and characterization of well‐defined ABC‐type triblock copolymers via atom transfer radical polymerization and stable free‐radical polymerization

An asymmetric difunctional initiator 2‐phenyl‐2‐[(2,2,6,6 tetramethylpiperidino)oxy] ethyl 2‐bromo propanoate ( 1 ) was used for the synthesis of ABC‐type methyl methacrylate (MMA)‐tert‐butylacrylate (tBA)‐styrene (St) triblock copolymers via a combination of atom transfer radical polymerization (ATRP) and stable free‐radical polymerization (SFRP). The ATRP‐ATRP‐SFRP or SFRP‐ATRP‐ATRP route led to ABC‐type triblock copolymers with controlled molecular weight and moderate polydispersity (M_w/M_n < 1.35). The block copolymers were characterized by gel permeation chromatography and ¹H NMR. The retaining chain‐end functionality and the applying halide exchange afforded high blocking efficiency as well as maintained control over entire routes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2025–2032, 2002     

Synthesis of a novel liquid crystal rod–coil star block copolymer consisting of poly(methyl methacrylate) and poly{2,5‐bis[(4‐methoxy‐phenyl)oxycarbonyl] styrene} via atom transfer radical polymerization

A bromine capped star‐shaped poly(methyl methacrylate) (S‐PMMA‐Br) was synthesized with CuBr/sparteine/PT‐Br as a catalyst and initiator to polymerize methyl methacrylate (MMA) according to atom transfer radical polymerization (ATRP). Then, with S‐PMMA‐Br as a macroinitiator, a series of new liquid crystal rod–coil star block copolymers with different molecular weights and low polydispersity were obtained by this method. The block architecture {coil‐conformation of the MMA segment and rigid‐rod conformation of 2,5‐bis[(4‐methoxyphenyl)oxycarbonyl] styrene segment} of the four‐armed rod–coil star block copolymers were characterized by ¹H NMR. The liquid‐crystalline behavior of these copolymers was studied by differential scanning calorimetry and polarized optical microscopy. We found that the liquid‐crystalline behavior depends on the molecular weight of the rigid segment; only the four‐armed rod–coil star block copolymers with each arm's M_n,_GPC of the rigid block beyond 0.91 × 10⁴ g/mol could form liquid‐crystalline phases above the glass‐transition temperature of the rigid block. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 733–741, 2005     

Cuso4‐amine redox‐initiated radical polymerization of methyl methacrylate mediated by a CuCl2 complex: Homogeneous reverse ATRP

Kinetic results of CuSO₄/2,2'‐bipyridine(bPy)‐amine redox initiated radical polymerization of methyl methacrylate (MMA) at 70 to 90 °C in dimethylsulfoxide suggest that such initiation is characteristic of a slow rate and a low initiator efficiency, but tertiary amines exhibit a relatively higher rate. UV‐Vis spectroscopy confirms the alpha‐amino functionality of PMMA chains. CuCl₂/bPy successfully mediates the redox‐initiated radical polymerization of MMA with aliphatic tertiary amines in a fashion of slow‐initiated reverse atom transfer radical polymerization (ATRP), i.e. both the initiator efficiency of aliphatic tertiary amines and the average molecular weight of PMMA increase gradually, while the molecular weight distribution remains narrow but become broader with the conversions. As the PMMA chains contain alpha amino and omega C‐Cl moieties, UV‐induced benzophenone‐initiated radical polymerization and Cu^ICl/bPy‐catalyzed ATRP initiated from PMMA lead to block copolymers from terminal functionalities. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2562‐2578     

Synthesis and characterization of amphiphilic heterograft copolymers with PAA and PS side chains via “Grafting from” approach

The amphiphilic heterograft copolymers poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate)‐graft‐(poly(acrylic acid)/polystyrene) (P(MMA‐co‐BIEM)‐g‐(PAA/PS)) were synthesized successfully by the combination of single electron transfer‐living radical polymerization (SET‐LRP), single electron transfer‐nitroxide radical coupling (SET‐NRC), atom transfer radical polymerization (ATRP), and nitroxide‐mediated polymerization (NMP) via the “grafting from” approach. First, the linear polymer backbones poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate) (P(MMA‐co‐BIEM)) were prepared by ATRP of methyl methacrylate (MMA) and 2‐hydroxyethyl methacrylate (HEMA) and subsequent esterification of the hydroxyl groups of the HEMA units with 2‐bromoisobutyryl bromide. Then the graft copolymers poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate)‐graft‐poly(t‐butyl acrylate) (P(MMA‐co‐BIEM)‐g‐PtBA) were prepared by SET‐LRP of t‐butyl acrylate (tBA) at room temperature in the presence of 2,2,6,6‐tetramethylpiperidin‐1‐yloxyl (TEMPO), where the capping efficiency of TEMPO was so high that nearly every TEMPO trapped one polymer radicals formed by SET. Finally, the formed alkoxyamines via SET‐NRC in the main chain were used to initiate NMP of styrene and following selectively cleavage of t‐butyl esters of the PtBA side chains afforded the amphiphilic heterograft copolymers poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate)‐graft‐(poly(t‐butyl acrylate)/polystyrene) (P(MMA‐co–BIEM)‐g‐(PtBA/PS)). The self‐assembly behaviors of the amphiphilic heterograft copolymers P(MMA‐co–BIEM)‐g‐(PAA/PS) in aqueous solution were investigated by AFM and DLS, and the results demonstrated that the morphologies of the formed micelles were dependent on the grafting density. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Controlled/living free‐radical copolymerization of 4‐(azidocarbonyl) phenyl methacrylate with methyl acrylate under 60Co γ‐ray irradiation

A new vinyl acyl azide monomer, 4‐(azidocarbonyl) phenyl methacrylate, has been synthesized and characterized by NMR and FTIR spectroscopy. The thermal stability of the new monomer has been investigated with FTIR and thermal gravimetry/differential thermal analysis (TG/DTA), and the monomer has been demonstrated to be stable below 50 °C in the solid state. The copolymerizations of the new monomer with methyl acrylate have been carried out at room temperature under ⁶⁰Co γ‐ray irradiation in the presence of benzyl 1H‐imidazole‐1‐carbodithioate. The results show that the polymerizations bear all the characteristics of controlled/living free‐radical polymerizations, such as the molecular weight increasing linearly with the monomer conversion, the molecular weight distribution being narrow (<1.20), and a linear relationship existing between ln([M]₀/[M]) and the polymerization time. The data from ¹H NMR and FTIR confirm that no change in the acyl azide groups has occurred in the polymerization process and that acyl azide copolymers have been obtained. The thermal stability of the polymers has also been investigated with TG/DTA and FTIR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2609–2616, 2007     

Macromolecular brushes synthesized by “grafting from” approach based on “click chemistry” and RAFT polymerization

Well‐defined macromolecular brushes with poly(N‐isopropyl acrylamide) (PNIPAM) side chains on random copolymer backbones were synthesized by “grafting from” approach based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization. To prepare macromolecular brushes, two linear random copolymers of 2‐(trimethylsilyloxy)ethyl methacrylate (HEMA‐TMS) and methyl methacrylate (MMA) (poly(MMA‐co‐HEMA‐TMS)) were synthesized by atom transfer radical polymerization and were subsequently derivated to azide‐containing polymers. Novel alkyne‐terminated RAFT chain transfer agent (CTA) was grafted to polymer backbones by copper‐catalyzed 1,3‐dipolar cycloaddition (azide‐alkyne click chemistry), and macro‐RAFT CTAs were obtained. PNIPAM side chains were prepared by RAFT polymerization. The macromolecular brushes have well‐defined structures, controlled molecular weights, and molecular weight distributions (M_w/M_n ≦ 1.23). The RAFT polymerization of NIPAM exhibited pseudo‐first‐order kinetics and a linear molecular weight dependence on monomer conversion, and no detectable termination was observed in the polymerization. The macromolecular brushes can self‐assemble into micelles in aqueous solution. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 443–453, 2010     

Thermoresponsive PPEGMEA‐g‐PPEGEEMA well‐defined double hydrophilic graft copolymer synthesized by successive SET‐LRP and ATRP

A series of well‐defined double hydrophilic graft copolymers containing poly[poly(ethylene glycol) methyl ether acrylate] (PPEGMEA) backbone and poly[poly(ethylene glycol) ethyl ether methacrylate] (PPEGEEMA) side chains were synthesized by the combination of single electron transfer‐living radical polymerization (SET‐LRP) and atom transfer radical polymerization (ATRP). The backbone was first prepared by SET‐LRP of poly(ethylene glycol) methyl ether acrylate macromonomer using CuBr/tris(2‐(dimethylamino)ethyl)amine as catalytic system. The obtained comb copolymer was treated with lithium diisopropylamide and 2‐bromoisobutyryl bromide to give PPEGMEA‐Br macroinitiator. Finally, PPEGMEA‐g‐PPEGEEMA graft copolymers were synthesized by ATRP of poly(ethylene glycol) ethyl ether methacrylate macromonomer using PPEGMEA‐Br macroinitiator via the grafting‐from route. The molecular weights of both the backbone and the side chains were controllable and the molecular weight distributions kept narrow (M_w/M_n ≤ 1.20). This kind of double hydrophilic copolymer was found to be stimuli‐responsive to both temperature and ion (0.3 M Cl^? and SO). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 647–655, 2010     

Atom transfer radical polymerization of methyl methacrylate via reversibly supported catalysts on silica gel via self‐assembly

A reversible catalyst immobilization system via self‐assembly of hydrogen bonding between thymine anchored on silica gel support and 2,6‐diaminopyridine functionalized with a catalyst (copper bromide‐N,N,N′,N′‐tetraethyldiethylenetriamine (TEDETA) complex) was developed for the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA). At elevated temperatures, the hydrogen bonding disassociated and released the catalyst as free small molecules for catalysis, which effectively mediated a living polymerization of MMA, producing PMMA with controlled molecular weight and narrow molecular weight distribution (<1.3). At room temperature, the catalyst assembled on the silica gel support by hydrogen bonding, and thus could be recovered and reused for a second run of ATRP. The recovered catalyst still mediated a living polymerization of MMA with reduced activity (54–64%), but had much improved control of the polymerization. The resulting PMMA had molecular weights very close to theoretical vales. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 22–30, 2004     

Facile synthesis of AB2‐type miktoarm star polymers through the combination of atom transfer radical polymerization and ring‐opening polymerization

A novel miktofunctional initiator ( 1 ), 2‐hydroxyethyl 3‐[(2‐bromopropanoyl)oxy]‐2‐{[(2‐bromopropanoyl)oxy]methyl}‐2‐methyl‐propanoate, possessing one initiating site for ring‐opening polymerization (ROP) and two initiating sites for atom transfer radical polymerization (ATRP), was synthesized in a three‐step reaction sequence. This initiator was first used in the ROP of ?‐caprolactone, and this led to a corresponding polymer with secondary bromide end groups. The obtained poly(?‐caprolactone) (PCL) was then used as a macroinitiator for the ATRP of tert‐butyl acrylate or methyl methacrylate, and this resulted in AB₂‐type PCL–[poly(tert‐butyl acrylate)]₂ or PCL–[poly(methyl methacrylate)]₂ miktoarm star polymers with controlled molecular weights and low polydispersities (weight‐average molecular weight/number‐average molecular weight < 1.23) via the ROP–ATRP sequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2313–2320, 2004     

Atom transfer radical polymerization of methyl methacrylate catalyzed by ion exchange resin immobilized Co(II) hybrid catalyst

Ion exchange resin immobilized Co(II) catalyst with a small amount of soluble CuCl₂/Me₆TREN catalyst was successfully applied to atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in DMF. Using this catalyst, a high conversion of MMA (>90%) was achieved. And poly(methyl methacrylate) (PMMA) with predicted molecular weight and narrow molecular weight distribution (M_w/M_n = 1.09–1.42) was obtained. The immobilized catalyst can be easily separated from the polymerization system by simple centrifugation after polymerization, resulting in the concentration of transition metal residues in polymer product was as low as 10 ppm. Both main catalytic activity and good controllability over the polymerization were retained by the recycled catalyst without any regeneration process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1416–1426, 2008     

Atom transfer radical polymerization of functional monomers employing Cu‐based catalysts at low concentration: Polymerization of glycidyl methacrylate

Initiators for continuous activator regeneration atom transfer radical polymerization (ICAR ATRP) of an epoxide‐containing monomer, glycidyl methacrylate (GMA), was successfully carried out using low concentration of catalyst (ca. 105 ppm) at 60 °C in anisole. The copper complex of tris(2‐pyridylmethyl)amine was used as the catalyst, diethyl 2‐bromo‐2‐methylmalonate as the initiator, and 2,2′‐azobisisobutyronitrile as the reducing agent. When moderate degrees of polymerization were targeted (up to 200), special purification of the monomer, other than removal of the polymerization inhibitor, was not required to achieve good control. To synthesize well‐defined polymers with higher degrees of polymerization (600), it was essential to use very pure monomer, and polymers of molecular weights exceeding 50,000 g mol^?1 and M_w/M_n = 1.10 were prepared. The developed procedures were used to chain‐extend bromine‐terminated poly(methyl methacrylate) macroinitiator prepared by activators regenerated by electron transfer (ARGET) ATRP. The Sn^II‐mediated ARGET ATRP technique was not suitable for the polymerization of GMA and resulted in polymers with multimodal molecular weight distributions. This was due to the occurrence of epoxide ring‐opening reactions, catalyzed by Sn^II and Sn^IV. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of well‐defined pH‐responsive PPEGMEA‐g‐P2VP double hydrophilic graft copolymer via sequential SET‐LRP and ATRP

A series of well‐defined double hydrophilic graft copolymers containing poly(poly(ethylene glycol) methyl ether acrylate) (PPEGMEA) backbone and poly(2‐vinylpyridine) (P2VP) side chains were synthesized by successive single electron transfer living radical polymerization (SET‐LRP) and atom transfer radical polymerization (ATRP). The backbone was first prepared by SET‐LRP of poly(ethylene glycol) methyl ether acrylate (PEGMEA) macromonomer using CuBr/tris(2‐(dimethylamino)ethyl)amine as catalytic system. The obtained homopolymer then reacted with lithium diisopropylamide and 2‐chloropropionyl chloride at ?78 °C to afford PPEGMEA‐Cl macroinitiator. poly(poly(ethylene glycol) methyl ether acrylate)‐g‐poly(2‐vinylpyridine) double hydrophilic graft copolymers were finally synthesized by. ATRP of 2‐vinylpyridine initiated by PPEGMEA‐Cl macroinitiator at 25 °C using CuCl/hexamethyldiethylenetriamine as catalytic system via the grafting‐ from strategy. The molecular weights of both the backbone and the side chains were controllable and the molecular weight distributions kept relatively narrow (M_w/M_n ≤ 1.40). pH‐Responsive micellization behavior was investigated by ¹H NMR, dynamic light scattering, and transmission electron microscopy and this kind of double hydrophilic graft copolymer aggregated to form micelles with P2VP‐core while pH of the aqueous solution was above 5.0. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

In situ‐generated Ru(III)‐mediated ATRP from the polymeric Ru(III) complex in the absence of activator generation agents

Past research has examined the atom transfer radical polymerization (ATRP) with high oxidation state metal complexes and without the need for any additives such as reducing agent or free radical initiator. To extend this research, half‐metallocene ruthenium(III) (Ru(III)) catalysts were used for the polymerization of methyl methacrylate (MMA) for the first time. These catalysts were generated in situ simply by mixing phosphorus‐containing ligand and pentamethylcyclopentadienyl (Cp*) Ru(III) polymer ((Cp*RuCl₂)_n). The complexes in their higher oxidation state such as Cp*RuCl₂(PPh₃) were air‐stable, highly active, and removable catalysts for the ATRPs of MMA with both precision control of molecular weight and narrow polydispersity index. The addition of ppm amount of metal catalyst contributed to the formation of very well‐defined homopolymers and copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

“Living”/controlled free radical polymerization of MMA in the presence of cobalt(II) 2‐ethylhexanoate: A switch from RAFT to ATRP mechanism

A metal complex, cobalt(II) 2‐ethylhexanoate (CEH), was added to the system of thermal‐initiated reversible addition‐fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN) as the RAFT agent at 115 °C. The polymerization rate was remarkably enhanced in the presence of CEH in comparison with that in the absence of CEH, and the increase of the CPDN concentration also accelerated the rate of polymerization. The polymerization in the concurrence of CPDN and CEH demonstrated the characters of “living”/controlled free radical polymerization: the number‐average molecular weights (M_n) increasing linearly with monomer conversion, narrow molecular weight distributions (M_w/M_n) and obtained PMMA end‐capped with the CPDN moieties. Meanwhile, CEH can also accelerate the rate of RAFT polymerization of MMA using the PMMA as macro‐RAFT agent instead of CPDN. Similar polymerization profiles were obtained when copper (I) bromide (CuBr)/N,N,N′,N′′,N′′‐pentamethyldiethylenetriamine was used instead of CEH. Extensive experiments in the presence of butyl methacrylate, bis(cyclopentadienyl) cobalt(II) and cumyl dithionaphthalenoate were also conducted; similar results as those of MMA/CPDN/CEH system were obtained. A transition of the polymerization mechanism, from RAFT process without CEH addition to atom transfer radical polymerization in the presence of CEH, was possibly responsible for polymerization profiles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5722–5730, 2007     

Simultaneous control of the stereospecificity and molecular weight in the ruthenium‐catalyzed living radical polymerization of methyl and 2‐hydroxyethyl methacrylates and sequential synthesis of stereoblock polymers

The stereospecific living radical polymerizations of methyl methacrylate (MMA) and 2‐hydroxyethyl methacrylate (HEMA) were achieved with a combination of ruthenium‐catalyzed living radical and solvent‐mediated stereospecific radical polymerizations. Among a series of ruthenium complexes [RuCl₂(PPh₃)₃, Ru(Ind)Cl(PPh₃)₂, and RuCp*Cl(PPh₃)₂], Cp*–ruthenium afforded poly(methyl methacrylate) with highly controlled molecular weights [weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.08] and high syndiotacticity (r = 88%) in a fluoroalcohol such as (CF₃)₂C(Ph)OH at 0 °C. On the other hand, a hydroxy‐functionalized monomer, HEMA, was polymerized with RuCp*Cl(PPh₃)₂ in N,N‐dimethylformamide and N,N‐dimethylacetamide (DMA) to give syndiotactic polymers (r = 87–88%) with controlled molecular weights (M_w/M_n = 1.12–1.16). This was the first example of the syndiospecific living radical polymerization of HEMA. A fluoroalcohol [(CF₃)₂C(Ph)OH], which induced the syndiospecific radical polymerization of MMA, reduced the syndiospecificity in the HEMA polymerization to result in more or less atactic polymers (mm/mr/rr = 7.2/40.9/51.9%) with controlled molecular weights in the presence of RuCp*Cl(PPh₃)₂ at 80 °C. A successive living radical polymerization of HEMA in two solvents, first DMA followed by (CF₃)₂C(Ph)OH, resulted in stereoblock poly(2‐hydroxyethyl methacrylate) with syndiotactic–atactic segments. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3609–3615, 2006     

ATRP of methyl methacrylate initiated with a bifunctional initiator bearing bromomethyl functional groups: Synthesis of the block and graft copolymers

This article reports the synthesis of the block and graft copolymers using peroxygen‐containing poly(methyl methacrylate) (poly‐MMA) as a macroinitiator that was prepared from the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in the presence of bis(4,4′‐bromomethyl benzoyl peroxide) (BBP). The effects of reaction temperatures on the ATRP system were studied in detail. Kinetic studies were carried out to investigate controlled ATRP for BBP/CuBr/bpy initiating system with MMA at 40 °C and free radical polymerization of styrene (S) at 80 °C. The plots of ln ([M_o]/[M_t]) versus reaction time are linear, corresponding to first‐order kinetics. Poly‐MMA initiators were used in the bulk polymerization of S to obtain poly (MMA‐b‐S) block copolymers. Poly‐MMA initiators containing undecomposed peroygen groups were used for the graft copolymerization of polybutadiene (PBd) and natural rubber (RSS‐3) to obtain crosslinked poly (MMA‐g‐PBd) and poly(MMA‐g‐RSS‐3) graft copolymers. Swelling ratio values (q_v) of the graft copolymers in CHCl₃ were calculated. The characterizations of the polymers were achieved by Fourier‐transform infrared spectroscopy (FTIR), ¹H‐nuclear magnetic resonance (¹H NMR), gel‐permeation chromatography (GPC), differential scanning calorimetry (DSC), thermogravimetric analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), and the fractional precipitation (γ) techniques. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1364–1373, 2010     

PPEGMEA‐g‐PDEAEMA: Double hydrophilic double‐grafted copolymer stimuli‐responsive to both pH and salinity

A series of well‐defined double hydrophilic double‐grafted copolymers, consisting of polyacrylate backbone, hydrophilic poly(2‐(diethylamino)ethyl methacrylate) and poly(ethylene glycol) side chains, were synthesized by successive atom transfer radical polymerization. The backbone, poly[poly(ethylene glycol) methyl ether acrylate] (PPEGMEA) comb copolymer, was firstly prepared by ATRP of PEGMEA macromonomer via the grafting‐through route followed by reacting with lithium diisopropylamide and 2‐bromopropionyl chloride to give PPEGMEA‐Br macroinitiator of ATRP. Finally, poly[poly(ethylene glycol) methyl ether acrylate]‐g‐poly(2‐(diethylamino)ethyl methacrylate) graft copolymers were synthesized by ATRP of 2‐(diethylamino)ethyl methacrylate using PPEGMEA‐Br macroinitiator via the grafting‐from route. Poly(2‐(diethylamino)ethyl methacrylate) side chains were connected to polyacrylate backbone through stable C? C bonds instead of ester connections, which is tolerant of both acidic and basic environment. The molecular weights of both backbone and side chains were controllable and the molecular weight distributions kept relatively narrow (M_w/M_n ≤ 1.39). The results of fluorescence spectroscopy, dynamic laser light scattering and transmission electron microscopy showed this double hydrophilic copolymer was stimuli‐responsive to both pH and salinity. It can aggregate to form reversible micelles in basic surroundings which can be conveniently dissociated with the addition of salt at room temperature. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3142–3153, 2009