Determination of ultra trace amounts of cobalt and nickel in water samples by inductively coupled plasma-optical emission spectrometry after preconcentration on modified C18-silica extraction disks

A highly sensitive and accurate method for preconcentration and determination of ultra trace amounts of cobalt and nickel ions in water samples is proposed. The preconcentration is achieved using C₁₈-silica extraction disks modified with 5-(6-methoxy-2-benzothiazoleazo)-8-aminoquinoline (MBTAQ). The retained ions on the prepared solid phase was eluted with 10 ml of 0.01 M nitric acid and measured by inductively coupled plasma-optical emission spectrometry (ICP-OES). The influence of the type and amount of eluent used, pH, sample and eluent flow rates, amount of MBTAQ and the effect of other ions on extraction efficiency were investigated. The limits of detection of the method were 0.08 and 0.06 μg l^− 1 for cobalt and nickel, respectively, and provide an enrichment factor of 100. The results obtained on 10 successive extractions and elution cycles revealed relative standard deviations of 1.5 and 1.0% for cobalt and nickel, respectively. The proposed method has been applied to the determination of ultra trace amounts of cobalt and nickel ions in natural and synthetic water samples with satisfactory results.     

Pre-concentration of ultra trace amounts of copper,zinc, cobalt and nickel in environmental water samples using modified C18 extraction disks and determination by inductively coupled plasma–optical emission spectrometry

A highly sensitive and accurate method for pre-concentration and determination of ultra trace amounts of zinc, copper, cobalt and nickel ions in environmental water samples is proposed. The method is based on the solid phase extraction of these ions on C18-bonded silica extraction disks modified with a novel Schiff base 2,2′-[1,6-hexanediyl bis (nitriloethylidine)]bis-1-naphthol (HDN). The retained ions on the prepared solid phase was eluted with 10 mL 0.01 M nitric acid and measured by inductively coupled plasma–optical emission spectrometry. The extraction efficiency and the influence of the type and least amount of eluent for the stripping of ions from the disks, pH, flow rates of sample solution and eluent, amount of HDN, effect of other ions and breakthrough volume were evaluated. The limits of detection of the method were 0.2, 0.2, 0.8 and 0.6 µg L^?1 for zinc, copper, cobalt and nickel, respectively and an enrichment factor of 100 was obtained. The proposed method was applied for determination of zinc, copper, cobalt and nickel ions in some natural and synthetic water samples with satisfactory results.     

Speciation analysis of mercury contaminants in water samples by RP-HPLC after solid phase extraction on modified C18 extraction disks with 1,3-bis(2-cyanobenzene)triazene

A highly sensitive and accurate method for preconcentration and determination of ultra trace amounts of inorganic mercury and organomercury compounds in different water samples is proposed. The preconcentration is achieved using octadecyl silica (C₁₈) extraction disks modified with 1,3-bis(2-cyanobenzene)triazene (CBT). The retained analytes as their triazenide complexes on the solid phase was eluted with 10 ml acetonitrile and measured by reversed-phase high-performance liquid chromatography (RP-HPLC). Type and amount of eluent, pH, amount of CBT, flow rates of sample solution and eluent have been optimized in order to obtain quantitative recovery of the analytes. The effect of interfering ions, such as Cu²⁺, Mn²⁺, Fe²⁺, Al³⁺, Zn²⁺, Cd²⁺, Ca²⁺, Mg²⁺, Ba²⁺, Pb²⁺, K⁺ and Na⁺ usually present in water samples on the recovery of the analytes has also been investigated. The enrichment factor of 100 was obtained for all mercury species and the analytical detection limits of phenylmercury, methylmercury and Hg²⁺ were found as 0.8, 1.0 and 1.3 ng l^− 1, respectively. Stability of mercury species after extraction on the modified disks was studied and the results showed that complexes collected on the disks were stable for at least 5 days. The proposed method has been applied to the quantitative determination of mercury species in natural and synthetic water samples with recoveries more than 90%.     

Coupling on-line preconcentration by ion-exchange with microwave plasma torch-atomic emission spectrometry for the determination of cobalt and nickel

In the present work, a simple and sensitive preconcentration-microwave plasma torch-atomic emission spectrometric procedure was carried out for the determination of cobalt and nickel. The method was based upon a flow-injection system with on-line preconcentration of the metal ions on a minicolumn of a strong acid cation-exchange resin. The operation parameters including sample acidity, flow rate, loading time, and eluent concentration, flow rate were studied and optimized. Under the optimal experimental conditions the enrichment factors were calculated as 13.58 and 17.65 for cobalt and nickel, respectively. The relative standard deviations, 3.73% for cobalt and 4.23% for nickel (n = 7), and a sample throughput of 40 h^− 1 were obtained. Furthermore, the limits of detection were shown to be 1.28 and 1.80 μg·L^− 1 for cobalt and nickel, respectively. The method was applied to the determination of cobalt and nickel in tea samples and the accuracy was assessed through recovery experiments.     

Determination of nickel in natural waters by FAAS after sorption on octadecyl silica membrane disks modified with a recently synthesized Schiff's base

A simple, highly sensitive, accurate and selective method for the determination of trace amounts of Ni²⁺ ions in water samples is proposed. The method is based on the separation and preconcentration of Ni²⁺ on an octadecyl-bonded silica (ODBS) membrane disk modified by a recently synthesized Schiff’s base N,N′-bis (3-methylsalicylidene) ortho phenylene diamine (MSOPD) at pH 7. The synthesis of this extractant ligand is also described. The retained nickel on the membrane was eluted with 2×5 ml 0.5 M HNO₃ and measured by flame atomic absorption spectrometry (FAAS) at 232.0 nm. The extraction efficiency and the influence of the type and least amount of eluent for the stripping of Ni²⁺ from the disks, pH, flow rates of sample solution and eluent, amount of MSOPD, effect of other ions, and breakthrough volume were evaluated. The maximum capacity of the membrane disks modified by 3 mg of MSOPD was found to be 146±4 μg Ni²⁺. The 3σ limit of detection of the method was 30 ng per 1000 ml and also an enrichment factor of 250 was obtained. The proposed method has been applied to the determination of nickel in several water samples with satisfactory results.     

Simultaneous extraction of trace amounts of cobalt, nickel and copper ions using magnetic iron oxide nanoparticles without chelating agent

The present study investigates the application of Fe₃O₄ nanoparticles as an adsorbent for solid phase extraction and their subsequent determination of trace amounts of cobalt, nickel and copper from environmental water samples using flame atomic absorption spectrometry. The analyte ions were adsorbed on magnetic nanoparticles in the pH range of 10–12 and then, Fe₃O₄ nanoparticles were easily separated from the aqueous solution by applying an external magnetic field and decantation. Hence, no filtration or centrifugation was needed. After extraction and collection of magnetic nanoparticles, the analyte ions were desorbed using 1.0 M HNO₃. Several factors that may affect the preconcentration and extraction process, including pH, type and volume of eluent, sample volume, salt effect and matrix effect were optimized. Under the optimized conditions, linearity was maintained from 0.005–3.0 μg/mL for cobalt and nickel and 0.001 to 1.25 μg/mL for copper in the initial solution. The detection limits of this method for cobalt, nickel and copper ions were 0.9, 0.7 and 0.3 ng/mL, respectively. Finally, the method was successfully applied to the extraction and determination of the analyte ions in natural waters and reference plant samples.     

Synthesis of amberlite XAD-2-PC resin for preconcentration and determination of trace elements in food samples by flame atomic absorption spectrometry

A new chelating sorbent has been developed using Amberlite XAD-2 resin anchored with pyrocatechol through –N=C– group. This sorbent, characterised by elemental analysis and infrared (IR) spectra, was used as packing for the minicolumn in an on-line system preconcentration system for cadmium, cobalt, copper and nickel determination. Metal ions were sorbed in the minicolumn, from which it could be eluted directly to the nebulizer–burner system of the flame atomic absorption spectrometer (FAAS). Elution of all metals from minicolumn can be made with 0.50 mol L^− 1 HCl or HNO₃. The enrichment factors obtained were 16 (Cd), 24 (Co), 15 (Cu) and 19 (Ni), for 60 s preconcentration time, and 39 (Cd), 69 (Co), 36 (Cu) and 41 (Ni), if used 180 s preconcentration time. Under the optimum conditions, the proposed procedure allowed the determination of cadmium, cobalt, copper and nickel with detection limits of 0.31, 0.32, 0.39 and 1.64 μg L^− 1, respectively, when used preconcentration periods of 180 s. The accuracy of the developed procedure was sufficient and evaluated by the analysis of the certified reference materials NIST 1515 apple leaves and NIST 1570a spinach leaves. The method was applied to the analysis of food samples (spinach, black tea and rice flour).     

Flotation-separation and ICP-AES determination of ultra trace amounts of copper, cadmium, nickel and cobalt using 2-aminocyclopentene-1-dithiocarboxylic acid.

A rapid flotation method for separation and enrichment of ultra trace amounts of copper(II), cadmium(II), nickel(II) and cobalt(II) ions from water samples is established. At pH 6.5 and with sodium dodecylsulfate used as a foaming reagent, Cu2+, Cd2+, Ni2+ and Co2+ were separated simultaneously with 2-aminocyclopentene-1-dithiocarboxylic acid (ACDA) added to 1 l of aqueous solution. The proposed procedure of preconcentration is applied prior to the determination of these four analytes using inductivity coupled plasma-atomic emission spectrometry (ICP-AES). The effects of pH, concentration of ACDA, applicability of different surfactants and foreign ions on the separation efficiency were investigated. The preconcentration factor of the method is 1000 and the detection limits of copper(II), cadmium(II), nickel(II) and cobalt(II) ions are 0.078, 0.075, 0.072 and 0.080 ng ml(-1), respectively.     

Column solid-phase extraction with Chromosorb-102 resin and determination of trace elements in water and sediment samples by flame atomic absorption spectrometry

A column, solid-phase extraction (SPE), preconcentration method was developed for determination of Bi, Cd, Co, Cu, Fe, Ni and Pb ions in drinking water, sea water and sediment samples by flame atomic absorption spectrometry. The procedure is based on retention of analytes in the form of pyrrolidine dithiocarbamate complexes on a short column of Chromosorb-102 resin from buffered sample solution and then their elution from the resin column with acetone. Several parameters, such as pH of the sample solution, amount of Chromosorb-102 resin, amount of ligand, volume of sample and eluent, type of eluent, flow rates of sample and eluent, governing the efficiency and throughput of the method were evaluated. The effects of divers ions on the preconcentration were also investigated. The recoveries were >95%. The developed method was applied to the determination of trace metal ions in drinking water, sea water and sediment samples, with satisfactory results. The 3σ detection limits for Cd, Cu, Fe, Ni and Pb and were found to be as 0.10, 0.44, 11, 3.6, and 10 μg l⁻¹, respectively. The relative standard deviation of the determination was <10%. The procedure was validated by the analysis of a standard reference material sediment (GBW 07309) and by use of a method based on coprecipitation.     

Graphene oxide-packed micro-column solid-phase extraction combined with flame atomic absorption spectrometry for determination of lead (II) and nickel (II) in water samples

A sensitive and simple method has been established for simultaneous preconcentration of trace amounts of Pb (II) and Ni (II) ions in water samples prior to their determination by flame atomic absorption spectrometry. This method was based on the using of a micro-column filled with graphene oxide as an adsorbent. The influences of various analytical parameters such as solution pH, adsorbent amount, eluent type and volume, flow rates of sample and eluent, and matrix ions on the recoveries of the metal ions were investigated. Using the optimum conditions, the calibration graphs were linear in the range of 7–260 and 5–85 μg L^?1 with detection limits (3S_b) of 2.1 and 1.4 μg L^?1 for lead and nickel ions, respectively. The relative standard deviation for 10 replicate determinations of 50 μg L^?1 of lead and nickel ions were 4.1% and 3.8%, respectively. The preconcentration factors were 102.5 and 95 for lead and nickel ions, respectively. The adsorption capacity of the adsorbent was also determined. The method was successfully applied to determine the trace amounts of Pb (II) and Ni (II) ions in real water samples. The validation of the method was also performed by the standard reference material.     

Preconcentration of trace amounts of beryllium in water samples on octadecyl silica cartridges modified by quinalizarine and its determination with atomic absorption spectrometry

A simple method has been developed for rapid and selective extraction, preconcentration and determination of trace amounts of beryllium. The extraction is carried out by octadecyl silica cartridge, modified with quinalizarine as a chelating agent. The effect of different parameters, such as sample matrix, flowrates of sample solution and eluent, pH, type and least amount of eluent for elution of Be(+2) ions from cartridge, breakthrough volume and limit of detection, were evaluated. Also, the effects of various cationic and anionic interferences on percent recovery of Be(+2) were studied. Be(+2) was extracted from solution at pH 6-6.6 and was eluted from modified cartridge with 5 ml of 0.5 M HNO(3). Extraction efficiencies >99% were obtained by elution of the cartridges with minimal amount of eluent. A preconcentration factor of 200 and a detection limit of 200 ng per 1000 ml were obtained. The method was applied to the recovery and determination of Be(+2) in different water and alloy samples.     

Application of a thiourea‐containing task‐specific ionic liquid for the solid‐phase extraction cleanup of lead ions from red lipstick,pine leaves,and water samples

Here, task‐specific ionic liquid solid‐phase extraction is proposed for the first time. In this approach, a thiourea‐functionalized ionic liquid is immobilized on the solid sorbent, multiwalled carbon nanotubes. These modified nanotubes packed into a solid‐phase extraction column are used for the selective extraction and preconcentration of ultra‐trace amounts of lead(II) from aqueous samples prior to electrothermal atomic absorption spectroscopy determination. The thiourea functional groups act as chelating agents for lead ions retaining them and so, give the selectivity to the sorbent. Elution of the retained ions can be performed using an acidic thiourea solution. The effects of experimental parameters including pH of the aqueous solution, type and amount of eluent, and the flow rates of sample and eluent solutions on the separation efficiency are investigated. The linear dependence of absorbance of lead on its concentration in the initial solution is in the range of 0.5–40.0 ng/mL with the detection limit of 0.13 ng/mL (3s_b/m, n = 10). The proposed method is applicable to the analysis of red lipstick, pine leaves, and water samples for their lead contents.     

Preconcentration of cobalt using Amberlyst 36 as a solid-phase extractor and its determination in various environmental samples by flame atomic absorption spectrometry

A new and simple column-solid-phase extraction method has been developed to separate and preconcentrate trace cobalt in water and soil prior to its determination by flame atomic absorption spectrometry (FAAS). Different factors such as pH of sample solution, sample volume, amount of resin, flow rate of aqueous solution, volume and concentration of eluent, and matrix effects for preconcentration were optimized. Under optimized experimentally established conditions, an analytical detection limit of 0.44?µg?L^?1, precision (RSD) of 1.9%, enrichment factor of 200, and capacity of resin of 82?mg?g^?1 were obtained. The method was applied for cobalt determination by FAAS in tap water, natural drinking water, soil, and roadside dust samples. The accuracy of the method is confirmed by analysing standard reference material (Montana Soil, SRM 2711).     

Solid-phase extraction and determination of ultra trace amounts of lead,mercury and cadmium in water samples using octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid) and atomic absorption spectrometry

A simple and fast method for preconcentration and determination of ultra trace amounts of lead(II), mercury(II) and cadmium(II) in water samples is presented. Lead, mercury and cadmium adsorbed quantitatively during passage of water samples (pH?=?7, flow rate?=?20 mL min^?1) through octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid). The retained lead, mercury and cadmium are then stripped from the disk with a minimal amount of 1 M hydrochloric acid solution as eluent, and determined by atomic absorption spectrometry. The influence of flow rates of the eluent and sample solution, the amount of ligand, type and least amount of eluent, pH of sample, effect of other ions and breakthrough volume are determined. The breakthrough volume of the method is greater than 2000 mL for lead and greater than 1500 mL for mercury and cadmium, which results in an enrichment factor of 200 for lead and an enrichment factor of 150 for both mercury and cadmium. The limit of detection of the proposed method is 177, 2 and 13 ng l^?1 for lead, mercury and cadmium, respectively.     

Application of Graphene as a Sorbent for Simultaneous Preconcentration and Determination of Trace Amounts of Cobalt and Nickel in Environmental Water and Vegetable Samples

A new method using a column packed with graphene as adsorbent was developed for the preconcentration of trace amounts of cobalt (Co) and nickel (Ni) prior to their determinations by flame atomic absorption spectrometry. Several factors influencing the extraction efficiency of Co and Ni and their subsequent determinations, such as pH, amounts of the chelating agent, flow rates of sample and eluent solution, eluent type and its volume, breakthrough volume, and adsorption capacity were established. Under the optimum conditions, the calibration graphs were linear in the range of 4.0‐200.0 μg L^?1 and 5.0‐200.0 μg L^?1 with detection limits of 0.36 μg L^?1 and 0.51 μg L^?1 for Co and Ni, respectively. Good relative standard deviations for ten determinations of 100.0 μg L^?1 of Co and Ni were 3.2 and 3.6%, respectively. The results for determination of Co and Ni in tap water, river water, sea water, vegetable and spiked samples have demonstrated the accuracy and applicability of the proposed method. To validate the proposed method, three certified reference materials of environment water (GSBZ 50030‐94 and GSB 07‐1186‐2000) and tomato leaf (GSBZ 51001‐94) were analyzed, and the determined values were in good agreement with the certified values.     

Determination of trace amounts of cadmium,copper and nickel in environmental water and food samples using GO/MgO nanocomposite as a new sorbent

A solid phase extraction method based on graphene oxide (GO) modified with magnesium oxide (MgO) nanoparticles was developed for the preconcentration and determination of trace amounts of cadmium, copper and nickel ions. The adsorbed analytes were eluted by 4.0 mL of 0.1 M (EDTA) and injected to flame atomic absorption spectrometer. The factors influencing the complex formation and extraction of these heavy metals were optimized. Studies on potential interference by various anions and cations showed the method to be highly selective. The preconcentration factor was about 11 with relative standard deviation of <4.0 for 8 replication determination. The detection limits for the Cd, Cu, Ni were found to be 0.5, 3.4 and 25 µg L^?1, respectively. The method was successfully applied for the determination of cadmium, copper and nickel in tap water, well water, sea water, rice and macaroni samples with spike recoveries ranging 93–105 %.     

Preconcentration of trace amounts of cobalt (II) ions in water and agricultural products samples using of 5-(4-dimethylaminobenzylidene) rhodanin modified SBA-15 sorbent prior to FAAS determination

In the present study, the ?5-(4-dimethylaminobenzylidene)rhodanin-modified SBA-15? was applied as stable solid sorbent for the separation and preconcentration of trace amounts of cobalt ions in aqueous solution. SBA-15 was modified by ?5-(4-dimethylaminobenzylidene)rhodanin reagent. The sorption of Co²⁺ ions was done onto modified sorbent in the pH range of 6.8–7.9 and desorption occurred in 5.0 mL of 3.0 mol L^?1 HNO₃. The results exhibit a linear dynamic range from 0.01 to 6.0 mg L^?1 for cobalt. Intra-day (repeatability) and inter-day (reproducibility) for 10 replicated determination of 0.06 mg L^?1 of cobalt was ±1.82% and ?±1.97%?. Detection limit was 4.2 µg L^?1 (3S_b, n = 5) and preconcentration factor was 80. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type and interference ions were studied for the preconcentration of Co²⁺. The proposed method was applied for the determination of cobalt in standard samples, water samples and agricultural products.     

Determination of Trace Amounts of Cobalt in Natural Water Samples as 4-(2-Thiazolylazo) Recorcinol Complex After Adsorptive Preconcentration

ABSTRACT

A chromatographic method has been established for the determination of trace amounts of cobalt by preconcentration on Amberlite XAD-16 resin as cobalt/4-(2-Thiazolylazo) resorcinol (TAR) complexes. The conditions (e.g. pH, resin amounts, matrix ions) affecting the recovery of cobalt from aqueous solution were studied. The method has been employed for the determination of cobalt in natural water samples.     

Flow Injection Semi-online Sorbent Extraction Preconcentration for Graphite Furnace Atomic Absorption Spectrometry

A micro-flow injection sorbent extraction preconcentration system was combined with a graphite furnace atomic absorption spectrometer. The combination results in an integrated system for the determination of trace amounts of heavy metals. Silica bonded with octadecyl functional groups (C₁₈) was used as a sorbent in a 15-μL conical microcolumn. The metals to be determined were preconcentrated as diethyl dithiocarbamate chelates onto the column for 60 s and then rinsed with deionized water and eluted with 40 μL of ethanol. Compared with direct injection of 40 μL of aqueous sample solution, enrichment factors of 30, 32, and 29 and detection limits (3ς) of 7.8, 12.8, and 3.9 ng/L for cobalt, nickel, and lead, respectively, were obtained with 60-s sample loading at 3.0 mL/min for sorbent extraction, 40 μL of eluate injection, and peak area measurement. The results obtained for trace amounts of cobalt, nickel, and lead in reference materials showed that there were no significant differences between the certified and determined values.     

Flame atomic absorption spectrometric determination of trace amounts of lead, cadmium and nickel in different matrixes after solid phase extraction on modified multiwalled carbon nanotubes

The potential of modified multiwalled carbon nanotubes (a solid-phase extraction sorbent), for the simultaneous separation and preconcentration of lead, cadmium and nickel; has been investigated. Lead, cadmium and nickel, were adsorbed quantitatively; on modified multiwalled carbon nanotubes (in the pH range of 2–4). Parameters influencing, the simultaneous preconcentration of Pb(II), Ni(II) and Cd(II) ions (such as pH of the sample, sample and eluent flow rate, type and volume of elution solution and interfering ions), have been examined and optimized. Under the optimum experimental conditions, the detection limits of this method. for Pb(II), Ni(II) and Cd(II) ions, were 0.32, 0.17 and 0.04 ng mL⁻¹ in original solution, respectively. Seven replicate determinations, of a mixture of 2.0 μg mL⁻¹ lead and nickel, and 1.0 μg mL⁻¹ cadmium; gave a mean absorbance of 0.074, 0.151 and 0.310, with relative standard deviation 1.7%, 1.5% and 1.2%, respectively. The method has been applied, to the determination of trace amounts of lead, cadmium and nickel; in biological and water samples, with satisfactory results.