Application of hollow fiber liquid-phase microextraction in identification of oil spill sources

In this study, hollow fiber based liquid-phase microextraction (HF-LPME), coupled with GC, GC–MS and GC–IRMS detections, was employed to determine petroleum hydrocarbons in spilled oils. According to the results, the HF-LPME method collected more low-molecular weight components, such as C₇–C₁₁n-alkanes, naphthalene, and phenanthrene, than those collected in conventional liquid–liquid extraction (LLE). The results also showed that this method had no remarkable effect on the distributions of high-molecular weight compounds such as >C₁₈n-alkanes, C₁–C₃ phenanthrene, and hopanes. Also, the carbon isotopic compositions of individual n-alkanes in the two preparation processes were identical. Accordingly, HF-LPME, as a simple, fast, and inexpensive sample preparation technique, could become a promising method for the identification of oil spill sources.     

Chromatographic study of the organic matter from Moroccan Rif bituminous rocks

The bituminous rocks of the Upper Cretaceous in the Moroccan Rif have been assessed and characterized in detail using organic geochemical techniques and a variety of organic geochemical parameters. The organic matter from 4 sites was studied in order to determine its thermal maturity and its depositional environments. The organic extracts (bitumens) were fractionated on silica-potassium hydroxide column according to the aliphatic hydrocarbons, acid compounds and polar compounds. Aliphatic hydrocarbons were identified by gas chromatography and mass spectrometry (GC/MS).The distribution of the aliphatic hydrocarbon fractions, and the various organic geochemical parameters (pristane/phytane, isoprenoids/n-alkanes, CPI, C₂₇:C₂₈:C₂₉ regular, C₂₉20S/(20S+20R), C₂₉ββ/(ββ+αα), C₂₉/C₃₀ hopanes and Ts/Tm) showed that the studied samples were generally mature. Two of the 4 samples appeared to be derived from source rocks deposited under anoxic conditions while suboxic to oxic conditions seemed to have been dominant for the remaining two samples. Rock–Eval pyrolysis data in addition to GC results suggested types II, III and IV kerogens for the studied samples.     

Tandem mass spectrometry of aminated fullerene derivatives

The products of the reaction between fullerenes (C₆₀/C₇₀) and dimethylamine were investigated by fast atom bombardment (FAB) mass spectrometry and tandem mass spectrometry (MS/MS). The FAB mass spectrum shows peaks corresponding to the addition of up to eight dimethylamine species, exclusively to C₇₀. MS/MS reveals an unusual fragmentation pattern. The mass spectrum of the reaction products, together with a number of tandem mass spectra, are shown.     

Experimental solubility data of various n-alkane waxes: effects of alkane chain length,alkane odd versus even carbon number structures,and solvent chemistry on solubility

Solubility data were measured for eight different n-alkanes ranging from tetracosane to tetratetracontane (C₂₄H₅₀–C₄₄H₉₀). Included are: (1) solubility data in toluene for all the n-alkanes studied and (2) solubility data of n-hexatriacontane (C₃₆H₇₄) in several solvent and solvent mixture systems. Illustrated in the data are the effects on solubility of alkane chain length, alkane odd versus even carbon number structures, and solvent chemistry. The measurements were made to provide fundamental equilibrium data.     

Application of urea adduction technique to polluted urban aerosols for the determination of hydrogen isotopic composition of n-alkanes

We examined an applicability of an improved urea adduction technique for the determination of hydrogen isotopic composition (δD) of homologous series of n-alkanes present in polluted urban aerosols using GC/TC/IRMS. Unresolved complex mixture (UCM) of hydrocarbons that interferes with accurate isotope measurements of n-alkanes was removed from n-alkane fraction by a urea adduction method. Recoveries of C₂₀ to C₃₀ n-alkanes during the urea adduction procedure were greater than 90% when the concentrations of total n-alkanes exceed 6.1?µg?mL^?1. Our compound-specific D/H ratios confirm the absence of significant hydrogen isotope fractionation in n-alkanes during urea adduction and recovery of the purified n-alkane fraction. We applied this technique to the urban aerosols that contain a large quantity of UCM to measure δD of C₂₀ to C₃₅ n-alkanes in urban aerosols from Tokyo and Sapporo with an accuracy less than 10‰. We found that the δD values widely ranged from ?38 to ?179‰. Based on the δD values of individual n-alkanes in aerosol samples, we can obtain further information on the sources of aerosol n-alkanes and their source regions, and the atmospheric processes such as long-range transport and atmospheric mixing of air masses of different origin.     

Py-GC/MS, GC/MS and FTIR investigations on LATE Roman-Egyptian adhesives from opus sectile: New insights into ancient recipes and technologies

An analytical protocol based on optical microscopy, Fourier transforms infrared spectroscopy (FTIR), analytical pyrolysis in the presence of hexamethyldisilazane followed by gas chromatographic/mass spectrometric analysis (Py-GC/MS) and gas chromatography/mass spectrometry after alkaline hydrolysis, solvent extraction and trimethylsilylation (GC/MS) was used in the chemical characterisation of the original adhesives used to fix monochrome and mosaic glass and stone plaques coming from the Late Roman archaeological site of Antinoopolis (Egypt).FTIR analysis demonstrated the presence of calcite fragments, and Py-GC/MS and GC/MS analyses provided detailed molecular compositions, highlighting the presence of a wide range of compound classes including diterpenoid acids, tricyclic abietanes with a high degree of aromatisation, mid- and long-chain monocarboxylic fatty acids, mono- and di-hydroxy acids, α,ω-dicaboxylic fatty acids, n-alkanols, and n-alkanes. Characteristic biomarkers and their distribution patterns indicated the presence of pine pitch in all the adhesives, which in some cases was admixed with beeswax and brassicaceae seed oil.The results provided new insights into the complex recipes used by artisans in ancient Egypt in the production of adhesives and in the sophisticated manufacture of opus sectile decorations.     

Quantitative Analysis of Long Chain Fatty Acids Present in a Type I Kerogen Using Electrospray Ionization Fourier Transform Ion Cyclotron Resonance Mass Spectrometry: Compared with BF3/MeOH Methylation/GC-FID

Long chain fatty acids (LCFAs) are present in various natural samples and are easily detectable using electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI-FT-ICR-MS) in negative ion mode. The capability of the ESI-FT-ICR-MS for quantifying LCFAs was evaluated by performing a standard addition followed by an internal standard methodology to several kerogen extracts using n-C₂₀ fatty acid as standard. As the concentration of the standard increased, the magnitude of its peak (m/z 311.29525) increased linearly but with two separate slopes, leaving the entire mass spectra relatively unchanged, which shows evidence of reproducibility. Response factors of other LCFAs are obtained using a standard addition approach. We employed five LCFA standards (n-C₁₅, n-C₁₉, n-C₂₄, n-C₂₆, and n-C₃₀) with different carbon numbers. This allowed us to determine the response factor of all fatty acids (with carbon number between 15 and 30) by plotting the slope of each standard versus its carbon number. With the observed response factors and use of the internal standard, the concentrations of LCFAs in four kerogen extracts were measured by ESI-FT-ICR-MS and compared with those from GC-FID. The carbon number distribution obtained by ESI-FT-ICR-MS matched well the GC-FID distribution (5%–50%) with the exception of C₁₆ and C₁₈, considering that ESI-FT-ICR-MS does not differentiate between normal and branched LCFAs, whereas GC-FID does. This allows one to quantitatively compare samples with a relatively similar matrix for specific compounds such as LCFAs with no need of time-consuming derivatization procedures. Moreover, the calibration can be extended to higher carbon numbers with ESI-FT-ICR-MS, beyond the capabilities of GC/MS.

Identification of endogenous and anthropogenic hydrocarbons in bottom deposits of peat lakes and evaluation of their contribution to the “hydrocarbon index”

Gas chromatography with mass spectrometric detection was used to analyze bitumens isolated from bottom sediments of peat lakes contaminated with petroleum products. Endogenous hydrocarbons are characterized by the presence of n-alkanes with an odd number of carbon atoms in the molecule in the characteristic region of C₂₃–C₃₃, the absence of a “hump” characteristic of oil products in the chromatogram, and the presence of light hydrocarbons, eluting in the initial part of the chromatogram (light hydrocarbons are usually lost when the sample is dried). The distribution profile of odd n-alkanes is used to assess the contribution of endogenous hydrocarbons to the “hydrocarbon index” with the help of the pattern recognition method. The concentration of light hydrocarbons is from 50 and 300–400 to 3500–5000 mg/kg for a number of samples and even up to 26000 mg/kg in some samples. The concentration of petroleum hydrocarbons and heteroatomic compounds varies from the lowest values of 30–80 mg/kg up to 20000 mg/kg and higher.     

Comparison of different mass spectrometry techniques in the measurement of L‐[ring‐13C6]phenylalanine incorporation into mixed muscle proteins

Precise measurement of low enrichment of stable isotope labeled amino‐acid tracers in tissue samples is a prerequisite in measuring tissue protein synthesis rates. The challenge of this analysis is augmented when small sample size is a critical factor. Muscle samples from human participants following an 8 h intravenous infusion of L‐[ring‐¹³C₆]phenylalanine and a bolus dose of L‐[ring‐¹³C₆]phenylalanine in a mouse were utilized. Liquid chromatography tandem mass spectrometry (LC/MS/MS), gas chromatography (GC) MS/MS and GC/MS were compared to the GC‐combustion‐isotope ratio MS (GC/C/IRMS), to measure mixed muscle protein enrichment of [ring‐¹³C₆]phenylalanine enrichment. The sample isotope enrichment ranged from 0.0091 to 0.1312 molar percent excess. As compared with GC/C/IRMS, LC/MS/MS, GC/MS/MS and GC/MS showed coefficients of determination of R² = 0.9962 and R² = 0.9942, and 0.9217 respectively. However, the precision of measurements (coefficients of variation) for intra‐assay are 13.0%, 1.7%, 6.3% and 13.5% and for inter‐assay are 9.2%, 3.2%, 10.2% and 25% for GC/C/IRMS, LC/MS/MS, GC/MS/MS and GC/MS, respectively. The muscle sample sizes required to obtain these results were 8 µg, 0.8 µg, 3 µg and 3 µg for GC/C/IRMS, LC/MS/MS, GC/MS/MS and GC/MS, respectively. We conclude that LC/MS/MS is optimally suited for precise measurements of L‐[ring‐¹³C₆]phenylalanine tracer enrichment in low abundance and in small quantity samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Analysis of pesticides by gas chromatography/multiphoton ionization/mass spectrometry using a femtosecond laser

Gas chromatography/multiphoton ionization/time-of-flight mass spectrometry (GC/MPI/TOFMS) was utilized for analysis of a standard mixture sample containing 49 pesticides and 4 real samples using the third-harmonic emission (267 nm) of a femtosecond Ti:sapphire laser (100 fs) as the ionization source. A sample of a standard mixture of n-alkane was also measured for calibration of the retention time indices of the pesticides. Two photons are required for the excitation of n-alkane due to an absorption band located in the far ultraviolet region (140 nm). The n-alkane molecule in the excited state was subsequently ionized either directly or by absorbing another photon because of a high ionization potential. Due to a large excess of energy, the molecular ion was decomposed and formed many fragment ions. Compared to n-alkanes, most of the pesticides were softly ionized by the femtosecond laser; one photon was used for excitation and another was used for the subsequent ionization. The pesticides with no conjugated double bond had a lower ionization efficiency. The present analytical instrument was applied to several samples prepared from a variety of vegetables and a single fruit after pretreatment with solid-phase extraction. Three pesticides were found in these samples, although some of them were not detected by conventional GC/EI/MS–MS due to insufficient sensitivity and selectivity.     

Saturated long-chain hydrocarbons from Annona squamosa L. bark

The unsaponified chloroform extract of Annona squamosa L. bark has been analysed by gas chromatography-mass spectrometry (GC–MS) and was shown to consist of the conventional, even carbon number dominant distribution of saturated n-alkane homologues (C₁₄–C₂₆). The heptadecane (5.75%) was the only odd carbon number hydrocarbon. The total amount of hydrocarbons found in the unsaponified chloroform extract was 24.60%.     

Detection of arsenic-containing hydrocarbons in a range of commercial fish oils by GC-ICPMS analysis

The present study describes the use of a simple solid-phase extraction procedure for the extraction of arsenic-containing hydrocarbons from fish oil followed by analysis using gas chromatography (GC) coupled to inductively coupled plasma mass spectrometry (ICPMS). The procedure permitted the analysis of a small sample amount, and the method was applied on a range of different commercial fish oils, including oils of anchovy (Engraulis ringens), Atlantic herring (Clupea harengus), sand eel (Ammodytes marinus), blue whiting (Micromesistius poutassou) and a commercial mixed fish oil (mix of oils of Atlantic herring, Atlantic cod (Gadus morhua) and saithe (Pollachius virens)). Total arsenic concentrations in the fish oils and in the extracts of the fish oils were determined by microwave-assisted acid digestion and ICPMS. The arsenic concentrations in the fish oils ranged from 5.9 to 8.7 mg kg^?1. Three dominant arsenic-containing hydrocarbons in addition to one minor unidentified compound were detected in all the oils using GC-ICPMS. The molecular structures of the arsenic-containing hydrocarbons, dimethylarsinoyl hydrocarbons (C₁₇H₃₈AsO, C₁₉H₄₂AsO, C₂₃H₃₈AsO), were verified using GC coupled to tandem mass spectrometry (MS/MS), and the accurate masses of the compounds were verified using quadrupole time-of-flight mass spectrometry (qTOF-MS). Additionally, total arsenic and the arsenic-containing hydrocarbons were studied in decontaminated and in non-decontaminated fish oils, where a reduced arsenic concentration was seen in the decontaminated fish oils. This provided an insight to how a decontamination procedure originally ascribed for the removal of persistent organic pollutants affects the level of arsenolipids present in fish oils.     

Sub-critical water extraction of bitumen from Huadian oil shale lumps

Three sizes of Huadian oil shale lumps from 1 cm to 10 cm were extracted by sub-critical water at 350 °C and 16 MPa for 2–70 h. The oil shale lumps were fractured alone the shale texture in sub-critical water that greatly improved the extraction efficiency of bitumen from the large- and middle-sized sample. The extract yields of bitumen from different sized samples were similar when the extraction time is longer than 20 h and stabilized at about 18 wt.% (ad) after 50 h duration. With the increase of extraction time, asphaltene and preasphaltene extracts were gradually decomposed to maltene. The gas chromatography–mass spectrometry (GC–MS) analysis of the extracts showed that n-alkanes, n-alk-1-enes, isoprenoids, n-alk-2-ones and n-alkanoic acids were the major components. In contrast, aromatic extracts were rare and most of them were remained in the shale residue. The pyrolysis gas chromatography–mass spectrometry (Py-GC–MS) analysis of the spent shale showed that the final undecomposed organics in kerogen were some macromolecular linear hydrocarbon, n-alk-2-ones and n-alkanoic acids fragments. The comparison of the classical pyrolyzate and the sub-critical water extracts showed that the water extracts contained more long-chain alkanes than anhydrous pyrolysis and the alkene extracts could transform to alkanes in sub-critical water. Moreover, the n-alkanoic acids could be decomposed to short-chain compounds through the cleavage of carbon carbon bonds.     

An international round-robin study for the analysis of particulate semi-volatile organics by thermal desorption gas chromatography mass spectrometry

Thermal desorption gas chromatography mass spectrometry (TD-GC/MS) is becoming more commonly used for the quantification and identification of organic compounds in particulate matter (PM), including ambient and source PM such as diesel particulate matter (DPM). It has been proven as an alternative to the traditional solvent extraction (SE) method and liquid injection gas chromatograph mass spectrometry (LI-GC/MS). However, little information is available on how different types of TD-GC/MS systems compare to each other for analysis of real-world PM samples or to direct LI-GC/MS for analysis of PM components in a test solution. To address this, CanmetENERGY Characterization Laboratory initiated a round robin with the participation of 10 laboratories worldwide. Three sample types were analysed: (i) a test solution with a suite of pure compounds commonly found in PM, analysed by TD-GC/MS and LI-GC/MS; (ii) a DPM sample, analysed by TD-GC/MS and SE; and (iii) an ambient PM sample, analysed by TD-GC/MS. The first part of the study showed good overall performance and comparability between the different TD-GC/MS systems and LI-GC/MS method for the analysis of PM components in a test solution, with some variability of results due to system types and parameters used, concentration of calibration standards, and whether or not an internal standards was used. The analysis of the DPM sample showed greater variability between laboratories and methods as many PM components were present near the detection limit and matrix effects particularly affected the TD-GC/MS analysis of heavier n-alkanes. In the last part of the study, for the analysis of an ambient PM sample by TD-GC/MS, the analysis of variance showed good comparison between labs for polycyclic aromatic hydrocarbons (94% non-significant), but slightly lower for n-alkanes (68%) and biomarkers (57%).     

Prediction of molecular weight and density of n-alkanes (C6-C44)

Heavy n-alkanes and their mixtures were characterized by high temperature-simulated distillation using gas chromatography with a capillary column. In this work, the atmospheric boiling point is determined by the HT-SimDis GC method. In this study, molecular weights and density of n-alkanes were evaluated with this method by using retention times and normal boiling points as input data. ASTM D2887 calibration mixture containing 17 n-alkanes in the C₆-C₄₄ range were used for qualitative analyses. Retention times (t_R) of n-alkanes were measured with this method. The other input data that normal boiling points (T_b) and molecular weight (M) had been taken in the literature. Experimental densities (at 20 °C) of n-alkanes were obtained from API Research Projects. Empirical molecular weight and density correlations were developed by using the nonlinear and multiple regressions with correlation coefficients. The results of calculations were compared with experimental data. Normal boiling point predictions were obtained as an average absolute deviation of 1.07%. Molecular weight and density results were evaluated as average absolute deviations of 0.68% and 0.21%, respectively.     

Comparison of UPLC and HPLC for Determination of trans-10-Hydroxy-2-Decenoic Acid Content in Royal Jelly by Ultrasound-Assisted Extraction with Internal Standard

Two well-known derivatization procedures, H₂SO₄–butanol and H₂SO₄–methanol esterification, were compared for application to GC–MS identification of organic acids in Bayer process liquors. H₂SO₄–butanol and H₂SO₄–methanol derivatization must be combined for analysis of carboxylic acids. Twenty organic acids were identified by gas chromatography–mass spectrometry. Heptanedioic, 3-methylhexanedioic, octanedioic, 1,3-benzenedicarboxylic, nonanedioic, decanedioic, hexadecanoic, 9,12-octadecadienoic, octadecanoic, and phthalic acids were identified for the first time in Bayer liquors. The retention times (y) and carbon numbers (x) of these seven n-dicarboxylic acids (C₄–C₁₀) were fit to a linear relationship by use of Microsoft Excel. These dicarboxylic acids and two benzenedicarboxylic acids were quantified by use of the internal standard method.     

Temperature dependence of the free energy of sorption ofn-alkanes and energy contribution of their methylene groups on columns with fullerene C60

The partial molar free energy, enthalpy, and entropy of sorption of C₁₁−C₂₃ n-alkanes were calculated on the basis of the GC data obtained on the glass capillary column coated with fullerene C₆₀ (Ful-60) as stationary phase. The thermodynamic parameters ofn-alkane sorption on a column with Ful-60 and a fused silica capillary column with polydimethylsiloxane OV-1 were determined and compared. The enthalpy-entropy compensation effect for the sorption ofn-alkanes on Ful-60 and OV-1 was found. A linear dependence of the partial molar free energy ofn-alkane sorption on the temperature of analysis and carbon chain length was found. The free energy contributions of the methylene groups were calculated, and their temperature dependences were studied. The differences in the temperature dependences of the energy contributions of methylene groups ofn-alkanes on Ful-60 and OV-1 were revealed. The entropy contribution is 68–82% of the enthalpy contribution which indicates a substantial role of the number of contacts with Ful-60 in retention ofn-alkanes. The ability of Ful-60 for dispersive interactions is similar to those of nonpolar liquid phases and substantially differs from that for carbon adsorbents. Fullerene columns were shown to be convenient for analysis of highly boiling organic substances in aqueous and organic solutions. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1490–1495, August, 1999.     

Structural Characterization of Lipopeptides from Brevibacillus brevis HOB1

Brevibacillus brevis HOB1 was isolated from the formation water of an oil field and found to produce lipopeptides. The separation of lipopeptides was successfully achieved by reversed-phase high-performance liquid chromatography (HPLC) leading to nine separated peaks. The chemical structures of these lipopeptides were studied by means of electrospray ionization mass spectrometry (ESI-MS), gas chromatography-mass spectrometry (GC/MS), HPLC and electrospray ionization tandem mass spectrometry (ESI-MS/MS). As the results, all the lipopeptides had peptide parts with the same amino acid composition of Asp, Glu, Val, and Leu in the molar ratio 1:1:1:4, while the lipid part was composed of C₁₃–C₁₅ β-hydroxy fatty acids. As the sequence of fraction 1 was determined to be N-Glu-Leu-Leu-Val-Asp-Leu-Leu-C, the same as surfactin, they were proposed to be surfactin isoforms. Fraction 4 (C₁₅ surfactin) exhibited a good surface activity of 26.8 mN/m with CMC of 9?×?10^?6 M. Surfactin is a powerful biosurfactant possessing biological activities. As far as we know, Br. brevis is a new surfactin-producing species.     

N-Alkanes in Air Particulates of the Eastern Province of Saudi Arabia

Abstract

Oil hydrocarbons represent a great proportion of organic compounds in the atmosphere. Information about these compounds in the atmosphere of the Eastern Province of Saudi Arabia is lacking. In this study, n-alkanes and polynuclear aromatic hydrocarbons in air particulates were determined. The highest median concentration levels of n-alkanes in three urban areas and three areas near oil production centers were 121 ng/m³ and 42.9 ng/m³, respectively. Polynuclear aromatic hydrocarbons were also detected, although they are present in too low concentration for reliable quantitative measurement by GC and GC/MS techniques. A positive correlation was found between the concentration levels of n-alkanes in air particulates and the total suspended particulates measured at most locations. The carbon preference index (CPI) and the presence of the unresolved complex envelope suggested an anthropogenic origin for the n-alkanes.