Model studies and a new melt polycondensation route to poly-bisphenol a–iso/terephthalate (polyarylate)

Alternate syntheses of polyarylate from dimethyl iso/terephthalate (DMI/DMT) and bisphenol-A (BPA) or bisphenol-A diacetate (BPAOAc) were investigated using a variety of catalysts. The model exchange of DMT with 4-t-butylphenol with loss of methanol proceeded moderately rapidly at rather low temperature (170°C) to produce to mono- and di-t-butylphenyl terephthalates. Dibutyltin oxide is the preferred catalyst. Alkali metal phenoxides are almost as effective but were less soluble. The model reaction of DMT with 4-tert-butylphenyl acetate involving loss of methyl acetate gave comparable results using dibutyltin oxide as catalyst. Based on these model results, polycondensations of DMI/DMT with BPAOAc under optimal conditions, gave polyarylate having an inherent viscosity 0.34 dL g^?1 in quantitative yield and light brown color. Polycondensation with BPA was unsatisfactory in terms of yield, molecular weight, and color.     

Synthesis of novel phosphinic acid-containing polymers

Three arylene difluoride monomers containing phosphine oxide ( 1 ), phosphinic acid ( 2 ), or phosphinate ester ( 3 ) groups were prepared and polymerized with bisphenol A to give novel poly-(arylene ether)s ( 4 , 5 , and 6 ). The polymers obtained had moderate molecular weights (η_inh: 0.14–0.30 dL g⁻¹ in N-methylpyrrolidinone) and glass-transition temperatures (T_g: 102–200 °C), depending on the phosphine group in the main chain. Using bis(4-fluorophenyl)sulfone as a comonomer improved the polymerization to give copolymers with higher solution viscosities. The stoichiometric investigation revealed that 7 mol % excess of fluoride monomer gave the highest molecular weight copolymer 8 with η_inh of 0.78 dL g⁻¹, which had a T_g of 176 °C, a T of 432 °C, and formed a hard film by casting from solution. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1854–1859, 2001     

Synthesis and characterization of aromatic polymers derived from 5‐perfluoroalkylisophthalic acid

A series of polyisophthalamides and polyisophthalates having perfluorinated side chains were prepared from 5‐perfluoroalkylisophthaloyl dichlorides. The aromatic polyamides and polyarylates synthesized by conventional low temperature solution polycondensation and interfacial polycondensation, respectively, had inherent viscosities of 0.19 to 1.28 dL g⁻¹ in yields of 65 to 100%. Solubilies of the resulting polymers were improved by incorporating nonafluorobutyl groups but not improved by incorporating heptadecafluorooctyl groups. Although the effect on the glass transition temperature (T_g) of incorporating perfluoroalkyl groups into the aromatic polyamides or polyarylate backbone is great, the incorporation maintained the thermal stability of the polymers. In spite of the rigid nature of perfluoroalkyl groups, T_gs were decreased by incorporating perfluoroalkyl groups. The value of the contact angle of water on the aromatic polyamides films gradually increased with incorporation of the perfluoroalkyl groups. On the other hand, the value of the contact angle remarkably increased when perfluoroalkyl groups were incorporated into polyarylates. The Owens γs were also calculated for some aromatic polyamides by measuring contact angles of diiodomethane on the polymer films. The γs were estimated at 23‐37 mN m⁻¹ and about 10% of them were contributed by hydrogen bonding. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1135–1141, 1999     

LCP aromatic polyesters by esterolysis melt polymerization

Polyarylates have previously been synthesized from acetate esters via esterolysis (loss of methyl acetate). This polycondensation can be extended to p‐substituted aromatic monomers for liquid crystal polyesters (LCPs). For AB‐type polymers, methyl p‐acetoxybenzoate and methyl 6‐acetoxynaphthoate were copolymerized to an LCP with reasonable molecular weights. Benzoate esters, methyl 4‐benzoyloxybenzoate (MBB) and methyl 6‐benzoyloxy‐2‐naphthoate (MBN), are also investigated. Several tin and antimony oxide catalysts were effective. The rate of esterolysis polymerization of MBB and MBN is slower than that of the corresponding acidolysis melt polymerization, but fast enough to give relatively high‐molecular‐weight polymers and similar thermal stability as commercial LCP prepared by acidolysis. Using these alternative benzoyloxy groups significantly reduced the color problem, because ketene loss cannot occur. Esterolysis melt polymerizations leading to AB/AABB‐type LCPs were performed using either dimethyl 2,6‐naphthalene dicarboxylate (DMND) or dimethyl terephthalate (DMT) with methyl 4‐acetoxybenzoate and phenylhydroquinone diacetate with tin and antimony catalysts. DMT‐based monomer compositions show much faster polymerization than DMND‐based compositions using antimony oxide catalyst. All these LCPs show a T_g in the 140–170 °C range as a result of the inclusion of the naphthalene and/or phenyl hydroquinone units in the polymer chain. Compositions completely off‐balanced on either side still lead to relatively high‐molecular‐weight copolyesters because either excess monomer can be removed during polymerization. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3586–3595, 2000     

Direct polycondensation in ionic liquids

Ionic liquids (ILs) are subject to an enormous research effort due to their unique properties, such as non-volatility, high solution and reactivity ability, etc. For the first time ILs have been used as a solvent for preparing polymers via direct polycondensation. The influence of IL's nature and reaction parameters upon the polymer formulation has been investigated. It is shown that direct polycondensation is successfully proceeded in ILs and triphenyl phosphite (condensing agent) without any additional extra components, such as LiCl and pyridine, using in similar reactions in ordinary molecular solvents. Various polyamides (η_inh=0.11-1.10 dl/g), polyamide imides (η_inh=0.48-1.41 dl/g), -hydrazides (η_inh=0.56-0.60 dl/g) and polyhydrazides (η_inh=0.71-1.32 dl/g) have been obtained in quantitative yield and high molecular weight.     

Synthesis and properties of poly(sulfone‐arylate) copolymers

Poly(sulfone‐arylate) was synthesized in a reaction between dihydroxy polysulfone prepolymers and either diphenyl terephthalate or terephthaloyl chloride. The dihydroxy polysulfone prepolymers had molecular weights of 2000 and 4000 g/mol. The polymerization with diphenyl terephthalate was carried out at high temperature (280 °C) in the presence of a catalyst, whereas the polymerization with terephthalic chloride was conducted in solution at low temperature in the presence of an acid acceptor. High‐molecular weight copolymers (η_inh ～ 0.60 dL/g) could be obtained through both methods. The copolymers were characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance, DMA, and differential scanning calorimetry measurements and were found to exhibit high T_g values. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3904–3913, 2009     

Synthesis of trans‐4‐hydroxy‐L‐proline‐based telechelic prepolymers and poly(ester‐urethane)

The synthesis of hydroxyproline‐based telechelic prepolymers by the condensation polymerization of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline methyl ester was investigated. All the polymerizations were carried out in the melt with stannous octoate as the catalyst and with different diols. The products were characterized by differential scanning calorimetry, proton nuclear magnetic resonance, infrared spectrophotometry, and inherent viscosity (η_inh). According to the analytic results, the η_inh value of the prepolymers depended on the kind and amount of diols that were added. With an increase in the 1,6‐hexanediol feed from 2 to 10 mol %, there was a decrease in η_inh from 0.78 to 0.41 along with a decrease in the glass‐transition temperature (T_g ) from 63 to 42 °C. When 2 mol % of different kinds of diols were used, η_inh ranged from 0.78 to 0.21, and T_g varied from 70 to 43 °C. These new prepolymers could be linked to poly(ester‐urethane) by the chain extender 1,6‐hexamethylene diisocyanate. The poly(ester‐urethane) was amorphous, and the T_g was 76 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2449–2455, 2000     

Ethynyl-terminated polyarylates: Synthesis and characterization

Hydroxy-terminated polyarylates (HTPA) with number-average molecular weights of approximately 2500, 5000, 7500, and 10,000 were synthesized and converted to corresponding 4-ethynylbenzolyloxy-terminated polyarylates (ETPA) by reaction with 4-ethynylbenzoyl chloride. The terminal ethynyl groups were thermally reacted to provide chain extension and crosslinking. The cured ETPA exhibited higher glass transition temperatures (T_g) and better solvent resistance than a high molecular weight linear polyarylate. Solvent resistance was further improved by curing 2,2-bis(4-ethynylbenzoyloxy-4′-phenyl) propane, a coreactant, with ETPA at concentrations of approximately 10% (w/w).     

Amorphous copolyesters based on bibenzoic acids and neopentyl glycol

High T_g amorphous copolyester thermoplastics were synthesized by incorporating 4,4′‐bibenzoate (4,4′BB) and 3,4′‐bibenzoate moieties into the polyester backbone via melt polycondensation. The high levels of crystallinity typically associated with 4,4′BB containing polyesters were suppressed through copolymerization of ethylene glycol, 1,4‐cyclohexane dimethanol, and neopentyl glycol (NPG) diols. NPG was shown to be highly effective in suppressing crystallization and was used to produce amorphous compositions with T_g’s as high as 129 °C. Diol ratios were determined by ¹H NMR spectroscopy and molecular weights were assessed with inherent viscosity (η_inh). Thermogravimetric analysis showed single‐step weight losses in the range of 395 – 419 °C. Differential scanning calorimetry was used to determine melting points and glass transition temperatures over a wide range of copolyester compositions and identified amorphous compositions. Dynamic mechanical analysis confirmed T_g’s and was used to study β‐relaxations below the T_g. Rheological analysis revealed the effect of NPG structures on shear thinning and thermal stability. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 579–587     

Synthesis of polycarbonate from dimethyl carbonate and bisphenol-a through a non-phosgene process

A novel nonphosgene process for producing bisphenol-A polycarbonate (PC) was developed through a transesterification between bisphenol-A (BPA) and dimethyl carbonate (DMC) and a melt-polycondensation of the resulting bisphenol-A bismethylcarbonate (1). The transesterification was carried out by heating bisphenol A in dimethylcarbonate in the presence of Lewis acid catalysts, removing the by-producing methanol using molecular shieves 4A. Among various catalysts, a combination of (Bu₂SnCl)₂O and dimethylaminopyridine gave the best results to produce 1 in 22% yield for 48 h. Using a larger amount of the molecular sieves further improved the yield to 80% in 120 h. The resulting 1 was heated under reduced pressure in the presence of titanium catalysts to produce PC in good yields. The resulting PC had high weight average molecular weight (M_w) of 75,000. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2087–2093, 1999     

Scalings of fluorine‐containing polyimides in cyclopentanone

Eight 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride‐4,4′‐diamino‐3,3′‐dimethylbiphenyl (6FDA‐OTOL) fractions and seven 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy) phenyl] propane dianhydride‐4,4′‐diamino‐3,3′‐dimethylbiphenyl (BISADA‐OTOL) fractions in cyclopentanone at 30 °C were characterized by a combination of viscometry and static and dynamic laser light scattering (LLS). In static LLS, the angular dependence of the absolute scattered intensity led to the weight‐average molar mass (M_w), the z‐average root mean square radius of gyration, and the second virial coefficient. In dynamic LLS, the Laplace inversion of each measured intensity–intensity time correlation function resulted in a corresponding translational diffusion coefficient distribution [G(D)]. The scalings of 〈D〉 (cm²/s) = 8.13 × 10⁻⁵ M_w^−0.47 and [η] (dL/g) = 2.36 × 10⁻³ M_w^0.54 for 6FDA‐OTOL and 〈D〉 (cm²/s) = 3.02 × 10⁻⁴ M_w^−0.60 and [η] (dL/g) = 2.32 × 10⁻³ M_w^0.53 for BISADA‐OTOL were established. With these scalings, we successfully converted each G(D) value into a corresponding molar mass distribution. At 30 °C, cyclopentanone is a good solvent for BISADA‐OTOL but a poor solvent for 6FDA‐OTOL; this can be attributed to an ether linkage in BISADA‐OTOL. Therefore, BISADA‐OTOL has a more extended chain conformation than 6FDA‐OTOL in cyclopentanone. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2077–2080, 2000     

Propagation rate coefficients of isobornyl acrylate,tert‐butyl acrylate and 1‐ethoxyethyl acrylate: A high frequency PLP‐SEC study

Pulsed laser polymerization (PLP) coupled to size exclusion chromatography (SEC) is considered to be the most accurate and reliable technique for the determination of absolute propagation rate coefficients, k_p. Herein, k_p data as a function of temperature were determined via PLP‐SEC for three acrylate monomers that are of particular synthetic interest (e.g., for the generation of amphiphilic block copolymers). The high‐T_g monomer isobornyl acrylate (iBoA) as well as the precursor monomers for the synthesis of hydrophilic poly(acrylic acid), tert‐butyl acrylate (tBuA), and 1‐ethoxyethyl acrylate (EEA) were investigated with respect to their propagation rate coefficient in a wide temperature range. By application of a 500 Hz laser repetition rate, data could be obtained up to a temperature of 80 °C. To arrive at absolute values for k_p, the Mark‐Houwink parameters of the polymers have been determined via on‐line light scattering and viscosimetry measurements. These read: K = 5.00 × 10⁵ dL g⁻¹, a = 0.75 (piBoA), K = 19.7 × 10⁵ dL g⁻¹, a = 0.66 (ptBA) and K = 1.53 × 10⁵ dL g⁻¹, a = 0.85 (pEEA). The bulky iBoA monomer shows the lowest propagation rate coefficient among the three monomers, while EEA is the fastest. The activation energies and Arrhenius factors read: (iBoA): log(A/L mol⁻¹ s⁻¹) = 7.05 and E_A = 17.0 kJ mol⁻¹; (tBuA): log(A/L mol⁻¹ s⁻¹) = 7.28 and E_A = 17.5 kJ mol⁻¹ and (EEA): log(A/L mol⁻¹ s⁻¹) = 6.80 and E_A = 13.8 kJ mol⁻¹. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6641–6654, 2009     

Rechargeable Sodium-Ion Battery Based on Polyazaacene Analogue Anode

The high theoretical specific capacity, strong structural designability and relatively inexpensive manufacturing cost make the exploration of organic electrode materials more attractive in recent years. In this article, owing to the large π-conjugated structure, plenty of nitrogen heteroatoms and multiring aromatic system, polyazaacene analogue poly(1,6-dihydropyrazino[2,3 g]quinoxaline-2,3,8-triyl-7-(2H)-ylidene-7,8-dimethylidene) (PQL) was applied as the anode in sodium-ion batteries (SIBs). PQL was almost insoluble in conventional liquid organic electrolyte (1 M NaClO₄ in ethylene carbonate (EC)/dimethyl carbonate (DMC) (v:v=1 : 1) with 5 % fluoroethylene carbonate (FEC)), which strongly improved its cycle stability. The initial discharge capacity was obtained to be 1825 mAh g⁻¹ at the current density of 100 mA g⁻¹ and stabilized at 317 mAh g⁻¹ after 400 cycles with the coulombic efficiency as high as 97 %. It not only showed good rate capability at high current densities (202, 183 mAh g⁻¹ at 1 A g⁻¹ and 1.5 A g⁻¹) but also had a superior energy density around 290 Wh kg⁻¹.     

Pyrimidine based carboxylic acid terminated aromatic and semiaromatic hyperbranched polyamide-esters: synthesis and characterization

Carboxylic acid terminated aromatic and semiaromatic hyperbranched polyamide-esters (HBPAEs) containing pyrimidine moieties were prepared by polycondensation of 4-hydroxy-2,6-diaminopyrimidine (CBB′) to a double molar ratio of various diacid chlorides (A₂) without any catalyst. The products were soluble in organic solvents, such as N,N-dimethylformamide, N-methyl-2-pyrrolidone and displayed glass transition temperature (T_g) between 180 and 244 °C. The polymerization products have been investigated with FTIR, ¹H and ¹³C NMR analyses and the degree of branching was higher than 60%. Amorphous polymers had inherent viscosity (η_inh) ranging between 0.21-0.28 dL/g and had excellent thermal stability with 10% weight loss at 346-508 °C.     

Chemoselective synthesis of polyamides containing hydroxyl and amino substituents by direct polycondensation

A convenient method for the synthesis of polyamides containing hydroxyl and amino substituents on the aromatic rings of the backbones was developed. These polymers were prepared readily by the chemoselective polycondensation of dicarboxylic acids with diamines with hydroxyl and amino functional groups via the activating agent diphenyl(2,3‐dihydro‐2‐thioxo‐3‐bezoxazolyl)phosphonate. The model reactions were studied in detail to demonstrate the feasibility of chemoselective polycondensation. The direct polycondensation of 5‐hydroxy or 5‐aminoisophthalic acid with 4,4′‐diamino‐4″‐hydroxytriphenylmethane proceeded smoothly under mild conditions and produced the desired polyamides with inherent viscosities up to 0.73 dL · g⁻¹. The polymers obtained were characterized by IR, ¹H NMR, and ¹³C NMR spectroscopies. The polymers were readily soluble in aprotic polar solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethyl formamide, and dimethyl sulfoxide. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3875–3882, 2000     

Metallocene‐mediated cationic ring‐opening polymerization of 2‐methyl‐ and 2‐phenyl‐oxazoline

The cationic ring‐opening polymerization of 2‐methyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline was efficiently used using bis(η⁵‐cyclopentadienyl)dimethyl zirconium, Cp₂ZrMe₂, or bis(η⁵‐tert‐butyl‐cyclopentadienyl)dimethyl hafnium in combination with either tris(pentafluorophenyl)borate or tetrakis(pentafluorophenyl)borate dimethylanilinum salt as initiation systems. The evolution of polymer yield, molecular weight, and molecular weight distribution with time was examined. In addition, the influence of the initiation system and the monomer on the control of the polymerization was studied. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 000: 000–000, 2011     

pH‐Responsive ampholytic terpolymers of acrylamide,sodium 3‐acrylamido‐3‐methylbutanoate,and (3‐acrylamidopropyl)trimethylammonium chloride. I. Synthesis and characterization

Low-charge-density ampholytic terpolymers composed of acrylamide, sodium 3-acrylamido-3-methylbutanoate (NaAMB), and (3-acrylamidopropyl)trimethylammonium chloride were prepared via free-radical polymerization in 0.5 M NaCl to yield terpolymers with random charge distributions. NaOOCH was used as a chain-transfer agent during the polymerization to eliminate the effects of the monomer feed composition on the degree of polymerization (DP) and to suppress gel effects and broadening of the molecular weight distribution. The terpolymer compositions were obtained via ¹³C NMR spectroscopy, and the residual counterion content was determined via elemental analysis for Na⁺ and Cl⁻. The molecular weights (MWs) and polydispersity indices (PDIs) were determined via size exclusion chromatography/multi-angle laser light scattering (SEC–MALLS); the terpolymer MWs ranged from 1.3–1.6 × 10⁶ g/mol, corresponding to DPs of 1.6–1.9 × 10⁴ repeat units, with all terpolymers exhibiting PDIs of less than 2.0. Intrinsic viscosities determined from SEC–MALLS data and the Flory–Fox relationship were compared to intrinsic viscosities determined via low-shear dilute-solution viscometry and were found to agree rather well. Data from the SEC–MALLS analysis were used to analyze the radius of gyration/molecular weight (R_g–M) relationships and the Mark–Houwink–Sakurada intrinsic viscosity/molecular weight ([η]–M) relationships for the terpolymers. The R_g–M and [η]–M relationships revealed that most of the terpolymers exhibited little or no excluded volume effects under size exclusion chromatography conditions. Potentiometric titration of terpolymer solutions in deionized water showed that the apparent pK_a value of the poly[acrylamide-co-sodium 3-acrylamido-3-methylbutanoate-co-(3-acrylamidopropyl)trimethylammonium chloride] terpolymers increased with increasing NaAMB content in the terpolymers and increasing ratios of anionic monomer to cationic monomer at a constant terpolymer charge density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3236–3251, 2004     

Spontaneous Ring‐Opening Polymerization of Macrocyclic Aromatic Thioether Ketones under Transient High‐Temperature Conditions

Summary: Spontaneous ring‐opening polymerization of macrocyclic aromatic thioether ketones [ 1,4‐SC₆H₄COC₆H₄ ]_n (n = 3 and 4), in which the thioether linkages are para to the ketone, occurs during rapid, transient heating to 480 °C, to afford a soluble, semi‐crystalline poly(thioether ketone) of high molar mass (η_inh > 1.0 dL · g⁻¹). Corresponding macrocyclic ether ketones, and a macrocyclic thioether ether ketone in which the thioether linkage is para to the ether rather than to the ketone, show no evidence of polymerization under analogous conditions.

The uncatalysed ring‐opening polymerization of macrocycle 1 , within the pores of an alumina microfiltration membrane, leads to formation of polymer 3 with the microstructure shown in the above scanning electron micrograph.     

Synthesis and characterization of new AB-type poly(etherimide)s containing bisphenol moieties

A series of new AB-type poly(etherimide)s having bisphenol-type moiety was prepared by the one-pot polyimidization using triphenylphosphite(TPP) in N-methyl-2-pyrrolidone(NMP)/pyridine solution at 150°C. Complete cyclodehydration was observed in the polymerizations as well as in model reactions. Polymers were obtained with inherent viscosities in the 0.27–0.49 dL/g range. The M_n and M_w/M_n of poly[4-(1,4-phenyleneoxy-1,4-phenylenehexafluoro-isopropylidene-1,4-phenylene)oxyphthalimide] (4d) with η_inh = 0.49 dL/g were 73,400 g/mol and 1.5, respectively. Most polymers could readily be dissolved in common organic solvents such as DMAc, NMP, and m-cresol. The polymer 4d was soluble even in chloroform. These polymers had glass transition temperatures between 205 and 235°C, and 5% weight loss temperatures in the range of 511–532°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3530–3536, 1999     

Determination of propagation rate coefficients for an α‐substituted acrylic ester: Pulsed laser polymerization of dimethyl itaconate

Pulsed laser polymerization experiments have been performed on the bulk polymerization of dimethyl itaconate over the temperature range 20–50 °C. The activation energy and frequency factor were calculated as 24.9 kJ/mol⁻¹ and 2.15 × 10⁵ L/mol⁻¹s⁻¹, respectively. The activation energy is comparable with the methacrylate series of monomers. The frequency factor is relatively small and reflects steric hindrance in the transition state caused by the bulky 1,1, disubstitution in the monomer (and consequently the radical). The Mark–Houwink–Kuhn–Sakurada constants were also determined for poly(dimethyl itaconate) in tetrahydrofuran, these are reported as 46 × 10⁻⁵ dL/g (K) and 0.51 (α). The influence of penultimate units (γ‐substituents) on homopropagation reactions is discussed particularly for polymerizations leading to significant 1,3 interactions in the resultant polymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2192–2200, 2000