Yttria stabilized zirconia solid electrolyte surface modification with ZrO<Subscript>2</Subscript>, Y<Subscript>2</Subscript>O<Subscript>3</Subscript>, and ZrO<Subscript>2</Subscript> + 9 mol % Y<Subscript>2</Subscript>O<Subscript>3</Subscript> films

The surface of ceramic electrolyte ZrO₂ + 9 mol % Y₂O₃, hereinafter referred to as YSZ (abbreviated yttria stabilized zirconia), was modified with 0.1 to 0.2 μm oxide films of ZrO₂, Y₂O₃, and YSZ (same composition as substrate) by dip coating in alcohol solutions of the relevant salts and further annealing. The results of scanning electronic microscopy and X-ray diffraction evidence epitaxial film growth. By means of impedance spectroscopy at the temperatures of 500 to 600°C, the effect of YZS electrolyte surface modification with ZrO₂, Y₂O₃, and YSZ films to the polarization resistance of silver electrode was studied.     

Synthesis and characterization of La<Subscript>0.8</Subscript>Sr<Subscript>0.2</Subscript>Co<Subscript>0.5</Subscript>Fe<Subscript>0.5</Subscript>O<Subscript>3±δ</Subscript> nanopowders by microwave assisted sol–gel route

Nano-crystalline La_0.8Sr_0.2Co_0.5Fe_0.5O_3±δ powder has been successfully synthesized by microwave assisted sol–gel (MWSG) method. The decomposition and crystallization behavior of the gel-precursor was studied by Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) analysis. From the result of FT-IR and X-ray diffraction patterns, it is found that a perovskite La_0.8Sr_0.2Co_0.5Fe_0.5O_3±δ was formed by irradiating the precursor at 700 W for 3 min, but the well-crystalline perovskite La_0.8Sr_0.2Co_0.5Fe_0.5O_3±δ was obtained at 700 W for 35 min. Morphological and specific area analysis of the powder were done by transmission electron microscopy (TEM), scanning electron microscope (SEM) and Brunauer–Emmett–Teller (BET). The surface areas measured was 38.9 m²/g and the grain size was ∼23 nm. Electrochemical properties of pure LSCF cathode on YSZ electrolyte at intermediate temperatures were investigated by using AC impedance analyzer, which shows a low area specific resistance (0.077 Ω cm² at 1073 K and 0.672 Ω cm² at 953 K). Moreover, the synthesis period of 20 h usually observed for conventional heating mode is reduced to a few minutes. Thus, the MWSG method is proved to be a novel, extremely facile, time-saving and energy-efficient route to synthesize LSCF powders.     

Development of solid–oxide fuel cell for reduced operating temperatures

A technique for formation of electrolyte thin films with the thickness of 6–10 μm of zirconia stabilized by yttria (YSZ) is developed on the basis of the method of chemical deposition from the vapor phase of organometallic compounds (MOCVD). Planar electrochemical cells based on film electrolyte with a supporting anode with the working surface area of 12 cm² were manufactured. A solid-oxide fuel cell (SOFC) based on two fuel cells was developed and its life cycle tests at reduced operating temperatures (<800°C) were carried out for 400 h. The maximum power density reached in the SOFC tests was 316 mW/cm².     

Options for adjustment of microstructure and conductivity of cathodic substrates of La(Sr)MnO<Subscript>3</Subscript>

The electrodes of solid-oxide fuel cells (SOFCs) must be characterized by high conductivity to decrease ohmic losses and sufficient porosity to provide high gas diffusion rate. In the cases, when the SOFC electrodes are substrates, they must be synthesized at the temperature above the temperature of formation of their solid-electrolyte coating. Herewith, manufacturing of supporting electrodes with the required micro-structure is rather complicated. The present paper studies the effect of the method of manufacturing of the initial La_0.6Sr_0.4MnO₃ (LSM) powders, their degree of dispersion, introduction of sintering additives and pore agents on their microstructure, conductivity, and possibility of adjusting the temperature of SOFC cathodic substrate formation at which the required characteristics are reached. It is shown that sintering of cathodic substrates to the relative density of 65–70% can be carried out at the temperatures from 1050 to 1350–1400°C, which would allow obtaining electrolyte films of powders with different sintering ability on such substrates. The average pore size in cathodic substrates can be varied in the range of 0.4 to 2.5 μm by using the initial LSM powder with different dispersion degree and by employing graphite as a pore agent. At 900°C, conductivity of cathodic substrates of LSM grows at an increase in their relative density from 50% to 70% approximately from 50 to 100 S/cm and weakly depends on the dispersion degree of the initial powders.     

Sintering behavior and ionic conductivity of Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>1.9</Subscript> with a small amount of MnO<Subscript>2</Subscript> doping

A 20% GdO_1.5 doped ceria solid solution with a small amount of MnO₂ doping (≤5% molar ratio) was prepared via the mixed oxide method from high-purity commercial powders with grain size around 0.2–0.5 μm. X-ray diffraction analysis indicated that all the samples exhibited the fluorite structure, and no new phase was found. The data from dilatometeric measurements and scanning electron microscopy observations revealed that 1% Mn doping reduced the sintering temperature by over 150 °C, and enhanced the densification and grain growth. Mn doping has little effect on grain interior conductivity, but a marked deterioration in grain boundary behavior is observed. This leads to a lower total conductivity in comparison with the undoped Ce_0.8Gd_0.2O_2–δ. Therefore, for solid oxide fuel cells (SOFCs) with Mn-containing compounds as electrodes, optimization of electrode fabrication conditions is needed to prevent the formation of a lower conductivity layer at the electrode/electrolyte interface since Mn will diffuse from the electrode side to the electrolyte during fabrication and operation of SOFCs. Electronic Publication     

Non-isothermal studies on crystallization kinetics of tellurite 20Li<Subscript>2</Subscript>O-80TeO<Subscript>2</Subscript> glass

Structural and thermal properties of the 20Li₂O-80TeO₂ glass were studied using X-ray diffraction analysis and differential scanning calorimetry techniques to understand and control the crystallization process on this glass. The γ-TeO₂, α-TeO₂ and α-Li₂Te₂O₅ phases were identified during the crystallization in this glass. Activation energies and Avrami exponent n were calculated from non-isothermal measurements for glasses with different particle size. The mean values of Avrami exponent were obtained for glasses with 63–75 and 45–63 μm particle sizes such as , but glasses with particle size 38–45 μm and smaller than 38 g,m presented .     

Silicon nitride nanofibers produced by the pyrolysis of SiCl<Subscript>4</Subscript> in H<Subscript>2</Subscript> and N<Subscript>2</Subscript> media

The synthesis of fibrous Si₃N₄ nanostructures by gas-phase chemical deposition during the pyrolysis of silicon tetrachloride in a hydrogen and nitrogen atmosphere was investigated. It was shown that the products contained both amorphous Si₃N₄ nanofibers and their α and β phases both with and without a silicon coating. In addition to the Si₃N₄ nanofibers the products also contained nanoribbons. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 2, pp. 81–84, March–April, 2007.     

Improved sintering and electrical properties of La-doped CeO<Subscript>2</Subscript> buffer layer for intermediate temperature solid oxide fuel cells using doped LaGaO<Subscript>3</Subscript> film prepared by screen printing process

Effects of a sintering agent for La-doped ceria (LDC) as a buffer layer to prevent a chemical reaction between Ni in anode and Sr- and Mg-doped lanthanum gallate (LSGM) electrolyte during sintering were studied for improving sintering and electrical properties. Electrochemical performance of anode-supported solid oxide fuel cells (SOFCs) using LDC and LSGM films prepared by screen printing and co-sintering (1,350 °C) was also investigated. The prepared cell with dense LDC (ca. 17 μm) and LSGM electrolyte (ca. 60 μm) films showed an open circuit voltage close to the theoretical value of 1.10 V and a high maximum power density (0.831 W cm^–2) at 700 °C. The addition of 1 wt.% LSGM to porous LDC buffer layer was effective for improving the sintering density and electrical conductivity, resulting in the high power density due to the decreased internal resistance loss.     

Synthesis of ammonia from natural gas at atmospheric pressure with doped ceria–Ca<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>–K<Subscript>3</Subscript>PO<Subscript>4</Subscript> composite electrolyte and its proton conductivity at intermediate temperature

A new type of oxide–salt composite electrolyte, yttrium doped ceria YDC–Ca₃(PO₄)₂–K₃PO₄, was developed and demonstrated for its promising use for ammonia synthesis. Using this composite electrolyte, ammonia was synthesized from nitrogen and natural gas at atmospheric pressure in the solid-state proton conducting cell reactor, and the optimal condition for ammonia production was determined . The evolved rate of ammonia is up to 6.95×10⁻⁹ mol s⁻¹ cm⁻².     

Multifunctional performances of nanocomposite SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> doped cationic EBODAC film coated on natural cellulose matrix

Reverse micellar microemulsions were utilised to synthesise stable lead titanate colloids from typical sol–gel type molecular precursors. The particles of a few nanometres in diameter that formed by hydrolysis in the micelle cores demonstrated a nanocrystalline texture without the need for thermal treatment. In a chemical solution deposition routine based on the nanoparticle dispersions, ferroelectric PbTiO₃ thin films showing excellent remanent polarisation of more than 50 μC cm⁻² were derived. The electrical characteristics of the layers were correlated to their microstructure which was controlled by the precursor composition and the annealing conditions. A columnar morphology that was realised by spinning on coatings of up to 100 nm in individual thickness proved most favourable with respect to the ferroelectric performance of the films.     

LaNi<Subscript>0.5</Subscript>Ti<Subscript>0.5</Subscript>O<Subscript>3</Subscript>/CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>-based sensor for sensitive determination of paracetamol

A novel electrochemical sensor based on LaNi_0.5Ti_0.5O₃/CoFe₂O₄ nanoparticle-modified electrode (LNT–CFO/GCE) for sensitive determination of paracetamol (PAR) was presented. Experimental conditions such as the concentration of LNT–CFO, pH value, and applied potential were investigated. Under the optimum conditions, the electrochemical performances of LNT–CFO/GCE have been researched on the oxidation of PAR. The electrochemical behaviors of PAR on LNT–CFO/GCE were investigated by cyclic voltammetry. The results showed that LNT–CFO/GCE exhibited excellent promotion to the oxidation of PAR. The over-potential of PAR decreased significantly on the modified electrode compared with that on bare GCE. Furthermore, the sensor exhibits good reproducibility, stability, and selectivity in PAR determination. Linear response was obtained in the range of 0.5 to 901 μM with a detection limit of 0.19 μM for PAR.     

Facile preparation and electrochemical properties of large-scale Li<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> nanobelts

Large-scale Li_1+x V₃O₈ nanobelts were successfully fabricated using filter paper as deposition substrate through a simple surface sol–gel method. The nanobelts were as long as tens of micrometers with widths of 0.4–1.0 μm and thickness of 50–100 nm. The nanobelts were characterized by X-ray diffration (XRD), Fourier infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM). The formation mechanism of the nanobelts was investigated, showing that the morphology of the nanobelts is mainly determined by the calcination temperature. Electrochemical properties of the Li_1+x V₃O₈ nanobelts were characterized by charge–discharge experiments, and the results demonstrate that the Li_1+x V₃O₈ nanobelts exhibit a high discharge capacity (278 mAh g⁻¹) and excellent cycling stability.     

Synthesis and colour properties of pigments based on terbium-dopped Mg<Subscript>2</Subscript>SnO<Subscript>4</Subscript>

The main aim of this work was to synthesize the magnesium orthostannate doped by terbium cations and tested whether these materials can be used for colouring of the different materials, e.g. organic binder and ceramic glazes. Initial composition of pigments was counted according the general formula 2MgO(1 − x)SnO₂–xTbO₂, where values of x varied from 0.1 to 0.5 in 0.1 steps. The simultaneous TG/DTA measurements of mixture containing tin oxide, magnesium carbonate hydroxide and terbium oxide showed that the formation of a new compound started at temperature 1,029 °C, but single-phase system was not prepared. Granulometric compositions of samples that were prepared by calcining at temperatures 1,300–1,400 °C are characterized by values of median (d ₅₀) in range 4–8 μm. The calcining temperature 1,500 °C caused the increase of the particle sizes at around 12 μm. The composition of sample 2MgO–1.5SnO₂–0.5TbO₂ and heating temperature 1,500 °C are the most suitable conditions for preparation of colourfully interesting pigment that can be recommended also for colouring of ceramic glazes. Especially, for colouring of decorative lead containing glaze G 07091 containing 5 wt% of PbO and 8 wt% of Al₂O₃.     

Low-temperature processing of sol-gel derived Pb(Zr,Ti)O<Subscript>3</Subscript> thick films using CO<Subscript>2</Subscript> laser annealing

Fabrication of ferroelectric Pb(Zr_0.52Ti_0.48)O₃ (PZT) thick films on a Pt/Ti/SiO₂/Si substrate using powder-mixing sol-gel spin coating and continuous wave CO₂ laser annealing technique to treat the specimens with at a relatively low temperature was investigated in the present work. PZT fine powders were prepared by drying and pyrolysis of sol-gel solutions and calcined at temperatures from 400 to 750°C. After fine powder-containing sol-gel solutions were spin-coated on a substrate and pyrolyzed, CO₂ laser annealing was carried out to heat treat the specimens. The results show that laser annealing provides an extremely efficient way to crystallize the materials, but an amorphous phase may also form in the case of overheating. Thicker films absorb laser energy more effectively and therefore melt at shorter periods, implying a significant volume effect. A film with thickness of 1 μm shows cracks and rough surface morphology and it was difficult to obtain acceptable electrical properties, indicating importance of controlling interfacial stress and choosing appropriate size of the mixing powders. On the other hand, a thick film of 5 μm annealed at 100 W/cm² for 15 s exhibits excellent properties (P _r = 36.1 μC/cm², E _c = 19.66 kV/cm). Films of 10 μm form a melting zone at the surface and a non-crystallized bottom layer easily at an energy density of 100 W/cm², showing poor electrical properties. Besides, porosity and electrical properties of thick films can be controlled using appropriate processing parameters, suggesting that CO₂ laser annealing of modified sol-gel films is suitable for fabricating films of low dielectric constants and high crystallinity.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Synthesis and structure of the polymeric complex [Ag<Subscript>2</Subscript>(Ph<Subscript>3</Subscript>P)<Subscript>2</Subscript>B<Subscript>10</Subscript>H<Subscript>10</Subscript>]<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>

A method for the synthesis of the silver(I) complex with the closo-decaborate anion and triphenylphosphine [Ag₂(Ph₃P)₂B₁₀H₁₀] _n was developed and the structure of this complex was studied. The polymeric chain of the complex is formed with participation of Ag(I) atoms, which coordinate the B₁₀H₁₀²⁻ anions through the apical (B(1)–B(2), B(9)–B(10)) and equatorial (B(3)–B(6), B(5)–B(8)) edges, the metalligand bonding occurring through three-center two-electron bonds (MHB). The P atoms of two triphenylphosphine molecules are also incorporated in the inner coordination sphere of the metal: the CN of the silver atom is 4 + 1.     

Constant current anodic stripping chronopotentiometric determination of uranium in uranium mineral ores via accumulation of K<Subscript>2</Subscript>UO<Subscript>2</Subscript>[Fe(CN)<Subscript>6</Subscript>] on the palladium plated aluminum electrode

In the present work the uranyl hexacyanoferrate (K₂UO₂[Fe(CN)₆]) is deposited on the palladized aluminum (Pd-Al) electrode from a \textUO₂^{2 +} + \textFe( \textCN )₆ ^{- 3} {\text{UO}}_{2}^{2 + } + {\text{Fe}}\left( {\text{CN}} \right)_{6}^{ - 3} solution. Then the anodic stripping chronopotentiometry (ASCP) was used to strip the K₂UO₂[Fe(CN)₆] from the Pd-Al surface. The operational conditions including: pH, K₃Fe(CN)₆ concentration, deposition potential, deposition time and stripping current were optimized. The ASCP calibration graph was linear in concentration range 10–460 μM. of \textUO₂^{2 +} {\text{UO}}_{2}^{2 + } and the detection limit was 8.5 μM. The interference of some concomitant ions during the deposition process of K₂UO₂[Fe(CN)₆] was studied. The proposed method was successfully applied for analysis of some uranium mineral ores.     

Inductively Coupled Plasma Synthesis of CeO<Subscript>2</Subscript>-based Powders from Liquid Solutions for SOFC Electrolytes

Doped cerium oxide (CeO₂) based electrolytes are attractive alternative materials to replace the existing yttria-stabilized zirconia (YSZ) used as electrolyte for SOFC (solid oxide fuel cells). Cerium oxide electrolytes offer a similar performance to YSZ electrolytes at a lower cell operating temperature (~600--800 ^°C), therefore reducing thermal stresses and solid state reactions among the cell components.Doped Ce_1-xMe_xO_2-x/2(Me = Gd, Sm or Y) fine \hbox{powders} were synthesized from nitrate salts dissolved in water using a radio frequency inductively coupled plasma reactor. It was demonstrated that the relative concentrations of Ce and dopants fed in the solutions were retained in the synthesized powders. The products were all nano-crystalline with the basic crystal structure of CeO₂ and the crystal size of the products was essentially independent of the dopant used. The particle size distributions obtained were multimodal and in most cases trimodal. The results obtained differ from a previously reported mechanism of particle synthesis from liquid precursors.     

Electrochemical deposition of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> for thermoelectric microdevices

The electrolyses of solutions of bismuth oxide and tellurium oxide in nitric acid with molar ratios of Bi:Te=3:3–4:3 lead to cathodic deposits of films of bismuth telluride (Bi₂Te₃), an n-type semiconductor. Current densities of 2–5 mA/cm² were applied. Voltammetric investigations showed that Bi₂Te₃ deposition occurred at potentials more negative than −0.125 V (Ag/AgCl, 3 M KCl). The deposit was identified as bismuth telluride (γ-phase) by X-ray analysis. Hall-effect measurements verified the n-type semiconducting behaviour. The films can be deposited in microstructures for thermoelectric microdevices like thermoelectric batteries or thermoelectric sensors.     

The electrochemical behavior of the LaSrCuO<Subscript>4 − δ</Subscript>/Ce<Subscript>0.9</Subscript>Gd<Subscript>0.1</Subscript>O<Subscript>2 − δ</Subscript> interface

The electrochemical behavior of the LaSrCuO_{4 − δ}/Ce_0.9Gd_0.1O_{2 − δ} interface is studied by impedance spectroscopy and cyclic voltammetry methods. By analyzing the dependence of the impedance frequency spectra on the oxygen partial pressure, the rate-determining stages of oxygen exchange are determined in the temperature interval of 500–900°C. For temperatures above 700°C, the adsorption of oxygen molecules and their dissociation to oxygen atoms are shown to make a substantial contribution to the polarization resistance of the overall electrode process, besides the charge-transfer resistance.