Synthesis and characterization of novel biodegradable folate conjugated polyurethanes

In order to obtain targeting polyurethane micelle drug carriers, a series of biodegradable folate conjugated polyurethanes (FPUs) were synthesized using poly(ethylene glycol) (PEG) and poly(ε-caprolactone) (PCL) as soft segments, L-lysine ethyl ester diisocyanate (LDI) and 1,3-propanediol (PDO) as hard segments, and folic acid-ethylenediamine conjugate (FA-EDA) as an end-capping reagent. The resultant FPUs were fully characterized by (1)H NMR, Fourier-transform infrared (FTIR) spectroscopy, ultraviolet spectrophotometry (UV), gel permeation chromatography (GPC), and differential scanning calorimetry (DSC). These polymers can self-assemble into micelles in aqueous solutions confirmed by dynamic light scattering (DLS), pyrene fluorescence probe techniques, and transmission electron microscopy (TEM). The results indicated that the bulk structures and micellar properties of the prepared polyurethanes could be controlled by varying the PEG content in the soft segments. The present work provides a facile approach to prepare amphiphilic multiblock copolymers with tumor targeting moiety, which is a good candidate as biodegradable carriers for active intracellular drug delivery.     

Phase morphology of hydrolysable polyurethanes derived from aqueous dispersions

Biodegradable polyurethanes are an interesting alternative to many applications that involve plastics since they can minimize environmental problems caused by the low rates of natural degradation of synthetic polymers. In addition, since waterborne polyurethanes are based on aqueous dispersions, they restrict the use of organic solvents during processing and application of the polymer, thus contributing furthermore to reduce environmental damage. In this work, aqueous anionic polyurethane dispersions (PUD) with tailorable susceptibility for hydrolysis were synthesized by progressively replacing polypropylene glycol (PPG) with a biodegradable polycaprolactone diol (PCL) as soft segments. The hard segments were formed by extending isophorone diisocyanate (IPDI) with hydrazine (HZ). Dimethylol propionic acid (DMPA) was used as ionic center and triethyl amine (TEA) as neutralizer. The degree of phase separation was evaluated mainly by infrared spectroscopy (FTIR) and small angle X-ray scattering (SAXS). The results indicated that phase separation between hard and soft segments of poly(ester-urethane) is more significant than that of poly(ether-urethane). Data obtained from SAXS experiments indicated that phase separation within soft domains can also be present in samples containing both polyester and polyether soft segments. Hydrolytic degradation of the polymers in buffer solution of pH 7.4 and alkaline solution was performed as an initial test. The results showed that the fraction of polyester soft segments in the polyurethanes can be used to tailor the susceptibility of the materials to hydrolytic attack. Polyurethanes having higher contents of polyester were more promptly hydrolytically degraded than polyurethanes containing only polyether segments.     

Poly(ester urethane)s with polycaprolactone soft segments: A morphological study

Two series of poly(ester urethane)s were prepared, containing polycaprolactone (PCL) as the soft segment with molecular weights of 530 and 2000. In each series, the soft‐segment/hard‐segment ratio was varied, and the morphological changes were monitored with differential scanning calorimetry, dynamic mechanical thermal analysis, wide‐angle X‐ray scattering, and scanning electron microscopy techniques. The polyurethanes with longer PCL segments retained their crystallinity, whereas those with shorter PCL segments did not. A morphological model is proposed, in which a continuous PCL‐rich matrix contains both PCL crystallites and domains of urethane hard segments. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4117–4130, 2002     

Characterization of Novel Biodegradable Segmented Polyurethanes Prepared from Amino-Acid Based Diisocyanate

Segmented polyurethanes (SPUs) which were expected to yield non-toxic degradation products were synthesized from lysine-based diisocyanate (LDI), 1,3-propanediol (PDO), and polycaprolactone diol (PCL). SPUs were synthesized via a standard two-step prepolymer method. The hard segment fraction was changed in order to tune the mechanical properties and the degradability. The aggregation structures of the SPUs were characterized by infrared spectroscopy and differential scanning calorimetry (DSC), temperature dependence of dynamic viscoelasticity, and small-angle X-ray scattering (SAXS). DSC and dynamic viscoelastic measurements revealed that the glass transition temperature (T_g) of the soft segment increased with an increase in the hard segment fraction. SAXS of SPUs revealed the aggregation states of hard and soft segments. Furthermore, the degradation of SPUs was investigated by exposing the polymers to a buffer solution at 310 K (pH=7.6). The degradation rate of SPUs increased with an increase in the soft segment fraction. This is because the soft segment has the hydrolyzable ester linkages and the ester linkages are susceptible to hydrolysis compared with the urethane linkages. Finally, an electrospray deposition method was used to fabricate biodegradable SPU micro-fibers. FE-SEM images showed that higher concentration of solution favored the formation of uniform biodegradable micro-fibers without beads-like structure.     

The degradation and biocompatibility of waterborne biodegradable polyurethanes for tissue engineering

To better investigate the degradation and biocompatibility of waterborne biodegradable polyurethanes for tissue engineering, a series of new waterborne biodegradable polyurethanes (PEGPUs) with low degree of crosslinking was synthesized using IPDI, BDO and L-lysine as hard segments, PCL and PEG as soft segment. The bulk structures and properties of the prepared polyurethanes were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), tensile mechanical tests and water contact angle (WCA) measurements. The degree of microphase separation was slightly improved because of the lowered crosslinking degree of these PEGPUs in comparison with the high cross-linking degree samples, leading to good mechanical properties, as indicated by DSC and stress-strain data. Moreover, biodegradability of the polyurethanes was evaluated in phosphate buffer solutions (PBS) under different pH values and enzymatic solution at pH 7.4 through weight loss monitoring. The results suggested that the degradation of these PEGPUs was closely related to their bulk and surface properties. And the degradation products didn’t show apparent inhibition effect against fibroblasts in vitro. These studies demonstrated that the waterborne biodegradable polyurethanes could find potential use in soft tissue engineering and tissue regeneration.     

聚氨酯硬链段球晶生长与软硬链锻混容性的关系

线型可溶性聚氨酯的硬链段结晶难以长成球晶 ,然而本实验室已经证明即使从熔体结晶硬链段也是能够长成球晶的 .研究了聚酯与聚醚型聚氨酯硬链段长球晶的规律 ,并发现聚氨酯硬链段长球晶的难易与聚氨酯软硬链段混容性密切相关 .动态力学分析 (DMA)与示差扫描量热 (DSC)实验表明聚ε 已内酯 (PCL)、聚已二酸丁二醇酯 (PTMA)、聚四氢呋喃 (PTMO)及聚环氧丙烷 (PPO)型聚氨酯的软硬链段混容性从前至后递减 .从熔体退火结晶时 ,聚氨酯硬链段长成球晶的退火温度范围是有限的 ,软硬链段混容性越好 ,聚氨酯硬链段能长成球晶的温度范围越窄 ,所需长的时间越长 .聚氨酯硬链段长球晶的下限温度取决于软硬链段间所存在的氢键作用 ,聚氨酯硬链段长球晶的上限温度与软硬链段混容性直接相关 .     

A facile approach to biodegradable poly(ε-caprolactone)-poly(ethylene glycol)-based polyurethanes containing pendant amino groups

A novel biodegradable poly(ε-caprolactone)-poly(ethylene glycol)-based polyurethanes (PCL-PEG-PU) with pendant amino groups was synthesized by direct coupling of PEG ester of NH₂-protected-(aspartic acid) (PEG-Asp-PEG diols) and poly(ε-caprolactone) (PCL) diols with hexamethylene dissocyanate (HDI) under mild reaction conditions and by subsequent deprotection of benzyloxycarbonyl (Cbz) groups. GPC, ¹H NMR, and ¹³C NMR studies confirmed the polymer structures and the complete deprotection. DSC and WXRD results indicated that the crystallinity of the copolymer was enhanced with increasing PCL diols in the copolymer. The content of amino group in the polymer could be adjusted by changing the molar ratio of PEG-Asp-PEG diols to PCL diols. Thus the results of this study provide a good way to prepare polyurethanes bearing hydrophilic PEG segments and reactive amino groups without complicated synthesis.     

Synthesis and degradation of nontoxic biodegradable waterborne polyurethanes elastomer with poly(ε-caprolactone) and poly(ethylene glycol) as soft segment

In this study, in order to obtain waterborne polyurethanes (WBPUs) with biocompatibility, biodegradability as well as good mechanical properties, a series of nontoxic cross-linked waterborne polyurethanes were designed and synthesized with isophorone diisocyanate (IPDI), poly(ε-caprolactone) (PCL), poly(ethylene glycol) (PEG), 1,4-butandiol (BDO) and l-lysine without any other organic agent involved in the whole synthetic process. The bulk structures and properties were characterized by DSC, IR and Instron, mainly focused on the effect of amount of PEG. Their corresponding biodegradability was examined with Lipase AK. The result showed that the prepared waterborne polyurethanes had very good tensile properties, allowing them to be well used as biomaterials. And the change of tensile properties with increasing of amount of PEG in the polymers could be assigned to the change of microphase separation, as indicated by DSC and IR data. A quite good biodegradability was achieved as judged from the change of tensile properties as a function of time. The current work demonstrated a new synthetic approach that can be more promising to prepare both nontoxic and biodegradable polyurethanes for soft tissue engineering applications or drug delivery.     

Self-healing biodegradable poly(urea-urethane) elastomers based on hydrogen bonding interactions

 Self-healing poly(urea-urethane)s (PUUs) showing a tolerance to mechanical damage are particularly desirable for high-performance elastomeric biomaterials. In this study a kind of biodegradable PUUs was synthesized from poly(ε-caprolactone) diol with L-lysine ethyl ester diisocyanate (LDI) extended with L-lysine ethyl ester dihydrochloride (LEED) in DMF and characterized by using ¹H-NMR, FTIR, DSC, XRD, SEM and tensile tests. Interestingly, they exhibited a self-healing characteristic upon exposure to 37℃ for as short as 30 min with the tensile strength keeping at 4.23 MPa and the elongation at break reaching to 627%. It is revealed that increasing the hard segment content in PUUs benefits the self-healing performance, and on the opposite increasing the soft segment content contributes to the biodegradability.     

Calorimetric and Dielectric Study of the Segmented Biodegradable Poly(ester‐urethane)s Based on Bacterial Poly[(R)‐3‐hydroxybutyrate]

Two series of segmented poly(ester‐urethane)s were synthesized from bacterial poly[(R)‐3‐hydroxybutyrate]‐diol (PHB‐diol), as hard segments, and either poly(ε‐caprolactone)‐diol (PCL‐diol) or poly(butylene adipate)‐diol (PBA‐diol), as soft segments, using 1,6‐hexamethylene diisocyanate as a chain extender. The hard‐segment content varied from 0 to 50 wt.‐%. These materials were characterized using ¹H NMR spectroscopy and GPC. The polymers obtained were investigated calorimetrically and dielectrically. DSC showed that the T_g of either the PCL or PBA soft segments are shifted to higher temperatures with increasing PHB hard‐segment content, revealing that either the PCL or PBA are mixed with small amounts of PHB in the amorphous domains. The results also showed that the crystallization of soft or hard segments was physically constrained by the microstructure of the other crystalline phase, which results in a decrease in the degree of crystallinity of either the soft or hard segments upon increase of the other component. The dielectric spectra of poly(ester‐urethane)s, based on PCL and PHB, showed two primary relaxation processes, designated as α_S and α_H, which correspond to glass–rubber transitions of PCL soft and PHB hard segments, respectively. Whereas in the case of other poly(ester‐urethane)s, derived from PBA and PHB, only one relaxation process was observed, which broadens and shifts to higher temperature with increasing PHB hard‐segment content. It was concluded from these results that our investigated materials exhibit micro‐phase separation of the hard and soft segments in the amorphous domains.     

环氧乙烷-四氢呋喃共聚醚基热塑性聚氨酯弹性体氢键体系的定量研究

氢键为热塑性聚氨酯弹性体内的重要键合力特征。该文基于氢键所引起基团的频移,以FTIR为主要的研究手段,并结合通过动态力学性能（DMA）研究所建立的评估硬段与软段之间混溶的定量方程,对所合成的以环氧乙烷－四氢呋喃无规共聚醚、2,4－甲苯二异氰酸酯以及1,4－丁二醇为原料的热塑性聚醚聚氨酯弹性体的氢键体系进行了定量化研究。结果表明,大约有30％的硬段混溶进入炊段相对软段的醚氧产生氢键作用,主要的氢键包括硬段羰基与硬段氨基之间的氢键以及硬段烷氧与硬段氨基之间的氢键,仍发生在硬段岛区内。     

Hydrogen bonding and crystallization in biodegradable multiblock poly(ester urethane) copolymer

The hydrogen bonding and crystallization of a biodegradable poly(ester urethane) copolymer based on poly(L ‐lactide) (PLLA) as the soft segment were investigated by FTIR. On slow cooling from melt, the onset and the progress of the crystallization of the urethane hard segments were correlated to the position, width, and relative intensity of the hydrogen‐bonded N? H stretching band. The interconversion between the “free” and hydrogen‐bonded N? H and C?O groups in the urethane units in the process was also revealed by 2D correlation analysis of the FTIR data. The crystallization of the PLLA soft segments was monitored by the ester C?O stretching and the skeletal vibrations. It was revealed that the PLLA crystallization was restricted by the phase separation and the urethane crystallization, and at cooling rates of 10 °C/min or higher, the crystallization of the PLLA soft segments was prohibited. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 685–695, 2009     

Synthesis and electrospinning of ε-polycaprolactone-bioactive glass hybrid biomaterials via a sol-gel process

Strategies of bone tissue engineering and regeneration rely on bioactive scaffolds to mimic the natural extracellular matrix (ECM) as templates onto which cells attach, multiply, migrate, and function. For this purpose, hybrid biomaterials based on smart combinations of biodegradable polymers and bioactive glasses (BGs) are of particular interest, since they exhibit tailored physical, biological, and mechanical properties, as well as predictable degradation behavior. In this study, hybrid biomaterials with different organic-inorganic ratios were successfully synthesized via a sol-gel process. Poly(ε-caprolactone) (PCL) and tertiary bioactive glass (BG) with a glass composition of 70 mol % SiO(2), 26 mol % CaO, and 4 mol % of P(2)O(5) were used as the polymer and inorganic phases, respectively. The polymer chains were successfully introduced into the inorganic sol while the networks were formed. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analyses (TGA), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX) were used to investigate the presence of different chemical groups, structural crystallinity, thermal property, elemental composition, and homogeneity of the synthesized hybrid biomaterials. Identification of chemical groups and the presence of molecular interaction by hydrogen bonding between the organic and inorganic phases was confirmed by FTIR. The XRD patterns showed that all PCL/BG hybrids (up to 60% polymer content) were amorphous. The TGA study revealed that the PCL/BG hybrid biomaterials were thermally stable, and good agreement was observed between the experimental and theoretical organic-inorganic ratios. The SEM/EDX results also revealed a homogeneous elemental distribution and demonstrated the successful incorporation of all the elements in the hybrid system. Finally, these synthesized hybrid biomaterials were successfully electrospun into 3D scaffolds. The resultant fibers have potential use as scaffolds for bone regeneration.     

In situ preparation of hetero-polymers/clay nanocomposites by CUAAC click chemistry

A series of polymer/clay nanocomposites containing mechanistically two different polymers, poly(ethylene glycol) (PEG) and poly(epsilon caprolactone) (PCL), were prepared by simultaneous copper(I)-catalyzed alkyne-azide cycloaddition click reactions. Both clickable polymers, PEG-Alkyne and PCL-Alkyne, were simultaneously clicked on to azide-functional montmorillonite (MMT-N₃) nanoclay to get corresponding PEG-PCL/MMT nanocomposites. The chemical structures of the resulting nanocomposites were verified by following azide and silicone-oxygen bands using FT-IR and characteristic bands of PEG and PCL segments using ¹H-NMR spectroscopy. The combined XRD and TEM analysis confirmed that all PEG-PCL/MMT nanocomposites had partially exfoliated/intercalated morphologies. In addition, the increase of MMT-N₃ loading not only improved the onset and maximum degradation temperatures of the nanocomposites but also their char yields. Furthermore, the incorporation of MMT-N₃ in the polymer matrix did not significantly influence the crystallization behavior of both PEG and PCL segments.     

Synthesis and characterization of poly(ɛ-caprolactone)/Fe3o4 nanocomposites by in situ polymerization

A series of magnetic nanocomposites based on poly(?-caprolactone) (PCL) and Fe₃O₄ nanoparticles were prepared using a facile in situ polymerization method. The chemical structures of the PCL/Fe₃O₄ nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy. Results of wide-angle X-ray diffraction (WAXD) showed that the incorporation of the Fe₃O₄ nanoparticles did not affect the crystallization structure of the PCL. Both scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the morphology and dispersion of the Fe₃O₄ nanoparticles within the as-synthesized nanocomposites. Results of differential scanning calorimetry (DSC) and polarizing optical microscopy (POM) showed that the crystallization temperature was raised and the spherulites size decreased by the presence of Fe₃O₄ nanoparticles in the nanocomposites due to the heterogeneous nucleation effect. The thermal stability of the PCL was depressed by incorporation of Fe₃O₄ nanoparticles from thermogravimetric analysis (TGA). The superparamagnetic behavior of the PCL/Fe₃O₄ nanocomposites was testified by the superconducting quantum interference device (SQUID) magnetometer analysis. The obtained biodegradable nanocomposites will have a great potential in magnetic resonance imaging contrast and targeted drug delivery.     

Polycaprolactone based biodegradable polyurethanes

Two series of segmented polyurethanes were prepared with systematic variation in soft and hard segment length. The soft segment was constituted by polycaprolactone (PCL) blocks of molecular masses 530 or 2000 and the hard segment (HS) by urethane blocks, in a concentration that varied from 12% to 44% in weight of the whole polyurethane. Morphological analyses indicated that the amount of crystallinity of copolymers was strongly dependent on the PCL molar mass and hard segment content. The copolymers with longer PCL soft segments (Mn=2000) were semicrystalline, but those with shorter PCL segment (Mn=530) were unable to crystallize. The primary factor affectingthe biodegradability of copolymers as evaluated by Sturm tests was the extent of the phase separation, and that the segmental blending of the less biodegradable polyurethane (HS) blocks with PCL in the amorphous phase had a critical unfavorable consequence, which may be attributed to the size of the accessible area by microorganisms.     

Synthesis,characterization and effects of arm number on properties of amphiphilic polyurethanes as drug delivery carriers

Amphiphilic polyurethanes based on methoxy poly(ethylene glycol) (mPEG) and poly(?-caprolactone) diol (PCL) with different arm numbers such as two, three and four were successfully synthesized. Their structures were confirmed by Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (¹H NMR) and gel permeation chromatography (GPC). The effects of arm number on properties of amphiphilic polyurethanes were studied. Pyrene fluorescence probe technique and dynamic light scattering (DLS) analyses showed that the CMC value and the micellar size of the resultant amphiphilic polyurethanes decreased and the micellar stability against dilution enhanced with increasing the arm number of polyurethane. Using indometacin (IMC) as a model drug, the results indicated that the drug loading capacity and in vitro drug sustained release effect of polyurethane with four arms were better than those of polyurethanes with two and three arms.     

Functionalization of polyurethanes by incorporation of alkyne side-groups to oligodiols and subsequent thiol–yne post-modification

A versatile and upscalable method for the synthesis of polyurethanes (PUs) bearing pendant functionalities at the hard–soft segment interface from easily accessible commercial oligodiols is described. Reactive alkyne groups were introduced to polytetrahydrofuran (PTHF), poly(ε-caprolactone) (PCL) and polydimethylsiloxane (PDMS) diols by cationic ring-opening polymerization of glycidyl propargyl ether using these oligodiols as macroinitiators. The resulting oligodiols, with alkyne side groups located at both chain ends, were subsequently reacted with 1,4-butanediol and hexamethylene diisocyanate for the synthesis of PUs, containing several pendant alkyne groups between the soft and hard segments. The functionalized PUs based on different soft segments (PTHF, PCL or PDMS) have been further modified via metal-free thiol–yne chemistry. Proper reaction conditions were found for quantitative radical thiol–yne coupling reactions with benzyl mercaptan and thioglycerol.     

Effect of molecular orientation on the biodegradability of aliphatic polyester

The effect of morphological microstructure on the biodegradability of aliphatic polyester, poly(ϵ -caprolactone) (PCL) was studied in terms of crystallite size, crystallinity and amorphous and crystalline orientation factors. Microstructural changes during hydrolysis/biodegradation of the drawn PCL films were investigated by the conventional small and wide angle X-ray scattering methods. The lower was the draw ratio, the higher the hydrolytic degradability or biodegradability. With the increase of the hydrolysis time, the long period, at earlier stage, decreased; then slightly recovered and the crystallinity increased while the lamellar thickness remained unchanged. The amorphous orientation factors start to decrease at earlier stage and gradually go down to zero before the end of hydrolysis. In the case of crystalline orientation factor, although the values decrease with increasing hydrolysis time, they do not reach zero point. After the biodegradation for 60 days, crystallinity, crystal lateral size and lamellar thickness in all drawn PCL films decreased, and then it was confirmed that even crystalline regions were degraded for long term biodegradation test.     

脂肪族水性聚氨酯的动态力学行为研究

合成了一系列脂肪族水性聚氨酯 .考察了软段的组成、软段分子量及DMPA用量对产物动态力学性能的影响作用 .实验结果表明 ,软段的化学结构对水性聚氨酯的相态结构影响很大 .聚醚型水性聚氨酯具有较低的软段玻璃化转变温度 (Tgs) .聚醚型产物的微相分离程度高于聚酯型产物 .当采用聚酯和聚醚二元醇为混合软段时 ,Tgs随软段中聚醚含量的提高而逐渐降低 .提高DMPA用量 ,软段玻璃化转变温度Tgs移向低温区 ,硬段玻璃化转变温度Tgh移向高温区 ,说明体系的微相分离程度加大 .当软段分子量较低时 ,产物为半相容结构 ,只有一个主转变峰 ,软段的玻璃化转变以肩峰的形式出现 ;当软段分子量较高时 ,产物的微相分离程度较高 ,可以分别观察到软段及硬段的玻璃化转变 .总之 ,通过改变软段的种类、组成和分子量以及DMPA用量 ,可以大幅度地改变水性聚氨酯的形态结构 .