Extraction of HCl,HBr, HNO3, HClO4, H2SO4 and CH3COOH by 4-(5-Nonyl)pyridine and 2-hexylpyridine in benzene and determination of their pKBH+ values

The extraction of HCl, HBr, HNO₃, HClO₄, H₂SO₄ and CH₃COOH into solutions of 4-(5-nonyl)pyridine (NPy) and 2-hexylpyridine (HPy) dissolved in benzene has been studied. The results show that the larger, less basic anions extract better (ClO ₄ ⁻ >CH₃COO⁻≥NO ₃ ⁻ >Br⁻>Cl⁻>HSO ₄ ⁻ ) due to their low aqueous hydration. The ionization constants of NPyH⁺ and HPyH⁺ as determined spectrophotometrically were found to be 5.97±0.06 and 5.94±0.05, respectively, at 25°C.     

Anion-exchange separation of Pt and Pd using perchloric and hydrochloric acid solutions

On Biorad Ag-1X8 anion-exchange resin (200–400 mesh), Pd and Pt may be separated from one another by elution with 0.2M HClO₄, and 5M HClO₄, respectively. If present, Au may be retained by making the elutriants 0.003M in HCl. Alternatively, reduction by H₂SO₃ enables elution of Pt²⁺ with 6M HCl before recovery of Pd²⁺ with 0.2M HClO₄·Ir⁴⁺ is reduced to Ir³⁺ by H₂SO₃ and may be eluted ahead of Pt²⁺ by 2M HCl.     

Determination of inorganic acids by ion chromatography with n-tetradecylphosphocholine (zwitterionic surfactant) as the stationary phase and pure water as the mobile phase

A new ion chromatographic (IC) system, in which n-tetradecylphosphocholine (TDPC, a phosphobetaine type of zwitterionic surfactant) was used as the stationary phase, pure water as the mobile phase, and conductivity as the method of detection, has been developed for the determination of inorganic acids. Five model acids, HCl, HNO₃, HClO₄, H₂SO₄, and H₃PO₄, were separated to baseline and eluted in the order H₃PO₄ > HCl > HNO₃ > H₂SO₄ > HClO₄. When peak areas were plotted against the concentrations of the acids in samples, linear calibration curves were obtained. Ultimate determination limits were approximately 1 mmol L^–1, but the discrimination of the method between solutions of different concentration was better than 10 μmol L^–1 for those model analytes. Salts of divalent cations could also be separated, but they were eluted faster than the acids. No separation was observed for the salts of monovalent cations. This newly proposed approach is applicable to the simultaneous determination of the inorganic acids (produced by reactions of NO_x, SO_x, and HCl with water) in aerosols.     

Extraction of some elements of the groups IV b and VI b with 1-phenyl-3-methyl-4-caproyl-pyrazolone-5 (PMCP) from aqueous mineral acid solutions

Solvent extraction of Cr(VI), Mo(VI), W(VI) and Hf(IV) with 1-phenyl-3-methyl-4-caproyl-pyrazolone-5 (PMCP) in methyl isobutylketone (MIBK), xylene and chloroform (CHCl₃) from mineral acid solutions was studied. Chromium(VI) is not extracted from any of the acids studied (HCl, H₂SO₄ and HClO₄). Molybdenum(VI) is quantitatively extracted by the reagent in xylene and CHCl₃ from HClO₄ and HNO₃ solutions. It is also extracted quantitatively by the reagent in MIBK from HCl, HNO₃ and H₂SO₄ solutions but the participation of the diluent as extractant is considerable. Tungsten(VI) is quantitatively extracted in xylene from 9M HClO₄ solution. MIBK used as diluent also affects its extraction with PMCP. Hafnium(IV) is not extracted from H₂SO₄ solutions while it extracts more than 99% at 3M HNO₃ and above. The extracted species likely are: MoO₂(PMCP)₂, WO₂(PMCP)₂ and Hf(PMCP)₄, respectively.     

The role of Cherenkov and liquid scintilation counting in evaluating the anion-exchange separation of210Pb−210Bi−210Po

Using as eluent a sequence of 3M HCl, 12M HCl, and 8M HNO₃, a mixture of²¹⁰Pb,²¹⁰Bi, and²¹⁰Po may be clearly separated on a column of Dowex 1×2−100 anion exchange resin. A Cherenkov count in H₂O and the variation in count rate with time confirm that the nuclides emerge in the order²¹⁰Pb→²¹⁰Bi→²¹⁰Po. If 12M HCl is replaced by 1.5M H₂SO₄/2.3 M Na₂SO₄, a clean separation also results, but recovery of²¹⁰Po becomes considerably more difficult. All three nuclides are readily detectable by liquid scintillation counting, with the efficiency for²¹⁰Pb in the 60–70% range. The Cherenkov aqueous counting efficiency for²¹⁰Bi is ∼14–15%.     

Preparation and characterization of ZrWMoO<Subscript>8</Subscript> powders with different morphologies

ZrWMoO₈ powders with different morphologies were obtained using ammonium tungstate, molybdate tungstate and zirconium tungstate as the starting materials by dehydrating the precursor ZrWMoO₇(OH)₂(H₂O)₂. The precursor was studied by thermo-gravimetric and differential scanning calorimetry (TG-DSC). The influence of the gelling agents (HCl, HClO₄, HNO₃, H₂SO₄ and H₃PO₄) on the crystallization process and crystal morphology of the products prepared was investigated by X-ray powder diffraction (XRD), scanning electron micrograph (SEM) and X-ray fluorescence spectrometer (XRF). Results showed that the morphology of the ZrWMoO₈ particles can be simply adjusted by changing the gelling agents, and the thermal expansion coefficients of cubic ZrWMoO₈ prepared in HCl solution are −3.84 × 10⁻⁶ K⁻¹ from 100°C to 700°C. __________ Translated from Chemical Journal of Chinese University, 2007, 28(3): 397–401 [译自: 高等学校化学学报]     

Liquid-liquid extraction of molybdenum(VI) and uranium(VI) by LIX 622

The order of extraction of Mo(VI) from 1M acid solutions by 5% (v/v) LIX 622 (HL) in benzene is HCl>HNO₃>HClO₄>H₂SO₄, and extraction decreases with increasing concentration of HCl and H₂SO₄, and increases slightly with increasing concentration of HNO₃ and HClO₄. The extracted species is shown to be MoO₂L₂ as established by IR data of organic extracts and the extracted species in the solid form. Extraction is almost quantitative at and above 10% LIX 622, and is found to be independent of [Mo(VI)] in the range of 10^–4 to 10^–3 M. The diluents CCl₄, CHCl₃ and C₆H₆ are found to be superior to solvents of high dielectric constant for extraction of Mo(VI). Extraction of uranium(VI) by 10% (v/v) LIX 622 in benzene was found to increase with increasing equilibrium pH (3.0 to 6.0), and becomes quantitative at pH 5.9. Tributyl phosphate acts as a modifier up to 2% (v/v). Thorium(IV) is almost not extracted by LIX 622 or its mixture. Separation of Mo(VI) and U(VI) is feasible.     

Comparison of Sample Digestion Procedures for the Determination of Arsenic in Bottom Sediment Using Hydride Generation AAS

Certified reference materials (JMS-2 and JMS-1 – Marine sediment, LKSD-1 Lake Sediment, and STSD-1 Stream Sediment) and bottom sediment were analysed for arsenic by hydride generation atomic absorption spectrometry (HG-AAS) after digestion by different methods (microwave digestion, digestion in aluminium block, dry digestion) and different combinations of acids (HNO₃, HCl, HClO₄, H₂SO₄). The study revealed that both wet and dry digestion can be used to digest the reference materials and bottom sediment. Exceptionally satisfactory results were produced by the application of aqua regia, HNO₃ + HCl + HClO₄, and HNO₃ + HCl mixtures. Addition of Mg(NO₃)₂ during dry digestion caused an increase in arsenic recovery in the reference materials and improved the accuracy of arsenic determination in the bottom sediments.     

The effect of sample preparation on metal determination in soil by FAAS

Different methods for the determination of several metals in soils by flame atomic absorption spectrometry (FAAS) were investigated. Different procedures for total dissolution of soil: I – HF+HClO₄, H₃BO₃, HCl digestion (conventional heating), II – HF+HClO₄, H₃BO₃ digestion followed by fusion with LiBO₂ (conventional heating) and III – HF+HCl+HNO₃, H₃BO₃ digestion (microwave heating), as well as a leaching procedure with HNO₃+HClO₄, HCl were tested and compared. For quality assessment, the certified reference material S-1 soil was used. For most of the investigated metals, the best accuracy and precision were achieved when the procedure I or III were used. The developed procedure was applied to the analysis of soil samples from crude oil refinery and dump of petroleum origin wastes regions. Received: 22 Dezember 1997 / Revised: 9 February 1998 / Accepted: 12 February 1998     

Liquid-liquid extraction of protactinium(V) using tri-iso-octylamine

Solvent extraction of protactinium with tri-iso-octyl-amine (TIOA) in xylene, benzene, carbon tetrachloride and chloroform from HCl, HF, HNO₃, HClO₄ and H₂SO₄ media was studied using ²³³Pa as a radiotracer. The extraction efficiencies of protactinium were determined as a function of shaking time, concentrations of mineral acids in aqueous phase, extractant concentrations and diluents in organic phase. The extraction mechanism was discussed. The results show that the extracted species in the organic phase is [(R₃N⁻H)_nPa(OH)_xCl _y ^5−x−y ].     

Solvent extraction of hafnium(IV) by TBP and topo from acidic organic-aqueous solutions

Tracer concentrations of Hf(IV) were extracted by 60% TBP solution in benzene from 5M HClO₄, 5M HCl, 6M HNO₃ and 8M H₂SO₄ solutions, and by 1·10^?4 M TOPO solution in benzene from 2M HClO₄ and 2M HCl solutions in the presence of a variety of organic solvents miscible with the aqueous phase. Whereas for TBP these solvents caused an increase of HF(IV) extraction, an opposite effect was observed for TOPO. The results were discussed from the point of view of various solute-solvent and solvent-solvent interactions.     

LIX 84 as an extractant for throium(IV), uranium(VI) and molybdenum(VI)

The extraction order of Th(IV), U(VI) and Mo(VI) based on pH_0.5 values is Mo(VI)>U(VI)>Th(IV). Quantitative extraction has been observed for U(VI) by mixture of 10% (v/v) LIX 84 and 0.1M dibenzoylmethane at pH 4.2 and by mixture of 10% LIX 84 and 0.05M HTTA in the pH range 5.5–7.3 and for Mo(VI) by 10% LIX 84 from chloride media at pH 1.5. The order of extraction of Mo(VI) from 1N acid solutions is HCl>H₂SO₄>HNO₃>HClO₄ and extraction decreases very rapidly with increase in the concentration of HCl as compared to that from H₂SO₄, HNO₃ and HClO₄ acid solutions. The diluents C₆H₆, CCl₄ and CHCl₂ are found to be superior ton-butyl alcohol and isoamyl alcohol for extraction of Mo(VI). Influence of concentration of different anions on the extraction of U(VI) and Mo(VI) has been studied. Very little extraction has been observed in case of Th(IV) by LIX 84 or its mixtures with other chelating extractants or neutral donors.     

Extraction of pertechnetate with tetraphenylphosphonium in the presence of various acids, salts and hydroxides

Solvent extraction of pertechnetate anions from aqueous solutions of some mineral acids (HCl, HNO₃, HClO₄, H₂SO₄), (NaCl, NaNO₃, NaClO₄, K₂CrO₄, NaCO₃), NaOH and NH₄OH by tetraphenylphosphonium chloride in chloroform and nitrobenzene was studied. The results are presented in the form of the dependencies of extraction characteristics of TcO ₄ ⁻ (distribution ratio, percentage of extraction) on the (C₆H₅)₄PCl, H⁺ and competitive anion concentrations. The solvent extraction of sub-and super-stoichiometric ratio of TcO ₄ ⁻ : (C₆H₅)₄P⁺ was performed. The extraction constant values of ion pairs TcO ₄ ⁻ −Cl⁻, TcO ₄ ⁻ −NO ₃ ⁻ , TcO ₄ ⁻ −ClO ₄ ⁻ and of individual anions TcO ₄ ⁻ , Cl⁻, NO ₃ ⁻ , ClO ₄ ⁻ were calculated.     

Extraction,complex formation and spectrophotometric determination of iron(III) with 2-carbethoxy-5-hydroxy-1-(4-tolyl)-4-pyridone

Summary The extraction of iron(III) from aqueous HCl, H₂SO₄, HClO₄, HNO₃ solutions by 2-carbethoxy-5-hydroxy-1-(4-tolyl)-4-pyridone (HA) dissolved in CHCl₃ has been studied. Quantitative extraction of iron(III) is achieved if the concentration of the acids does not exceed 1N. The composition of the iron (III)—HA complex formed in the organic phase was investigated spectrophotometrically, radiometrically and by analysis of the isolated species. In the aqueous phase iron (III) and HA form three different complexes, depending on the initial iron: HA concentration ratio and the pH of the solution. They are the violet FeA²⁺, the orange-red FeA₂ ⁺ and the orange-yellow FeA₃. The latter is identical with the complex found in the organic phase, which was isolated as a solid crystalline material and characterized by elemental analysis and infrared spectroscopy. A spectrophotometric method for the determination of iron(III) in the aqueous phase and in the chloroform solution, by extraction with HA, is described.

---

Zusammenfassung Die Extraktion von Fe(III) aus wäßrigen Lösungen von HCl, H₂SO₄, HClO₄ oder HNO₃ mit 2-Carbäthoxy-5-hydroxy-1-(4-tolyl)-4-pyridon (HA) in chloroformischer Lösung wurde untersucht. Sie verläuft quantitativ, wenn die Konzentration der Säure nicht größer ist als 1-n. Die Zusammensetzung des Fe(III)-HA-Komplexes in der organischen Phase wurde spektrophotometrisch, radiometrisch und durch Analyse der isolierten Substanz untersucht. In wäßrigem Milieu bilden Eisen(III) und HA drei verschiedene Komplexe je nach dem anfänglichen Konzentrationsverhältnis Fe(III): HA und je nach dem pH der Lösung. FeA²⁺ ist violett, FeA₂ ⁺ ist orange-rot und FeA₃ orangegelb. Diese Verbindung ist mit dem in der organischen Phase gefundenen Komplex identisch, der in kristallisierter Form isoliert und durch Elementaranalyse und IR-Spektrometrie charakterisiert wurde. Eine spektrophotometrische Methode zur Eisen(III)-Bestimmung in wäßriger Phase und in chloroformischer Lösung durch Extraktion mit HA wurde beschrieben.

     

Liquid-liquid extraction of 233Pa(V) with Aliquat 336</p> </p>

Summary The extraction of protactinium with Aliquat 336 (methyl-tri-caprylyl ammonium chloride) in toluene, cyclohexane and chloroform from HCl, HNO₃, H₂SO₄, HClO₄, HF and mixed HCl-HF media was investigated by radioactive tracer technique. Distribution ratios of protactinium between the aqueous solution and the organic phase were determined as a function of shaking time, concentrations of acid in aqueous solution phase, extractant concentration and type of diluents in the organic phase. Aliquat 336 can almost quantitatively extract protactinium from strong HCl solution. At the same time, small amounts of HF in HCl solutions have a strong effect on Pa distribution.</p> </p>     

Extraction of U(VI) by cyanex-272

Extraction of U(VI) from HNO₃, HCl and HClO₄ media using cyanex-272 (bis[2,4,4 trimethyl pentyl] phosphinic acid)/n-dodecane has been carried out. In the case of HNO₃ and HClO₄ media, the distribution ratio (D) value first decreases and then increases, whereas from HCl medium it first decreases and then remains constant with increase in H⁺ ion concentration. At lower acidities, U(VI) was extracted as UO₂(HA₂)₂ by an ion exchange mechanism, whereas at higher acidities as UO₂(NO₃)₂ ^.2(H₂A₂) following a solvation mechanism. The D for U(VI) by cyanex-272, PC-88A and DEHPA at low acidities follows the order cyanex-272 > PC-88A > DEHPA. Also, cyanex-272 was found to extract U(VI) more efficiently than TBP at 2M HNO₃. The effect of diluents on the extraction of U(VI) by cyanex-272 followed the order cyclohexane > n-dodecane > CCl₄ > benzene. The loading of U(VI) into cyanex-272/n-dodecane from 2M HNO₃ has shown that at saturation point, cyanex-272 was 78% loaded. No third phase was observed at the saturation level. The stripping of U(VI) from the loaded organic phase was not possible with water, it was poor with acetic acid and sodium acetate but quantitative with oxalic acid, ammonium carbonate and sodium carbonate.     

Thiocyanate-selective electrode based on N-salicylidene-benzylamineato copper(II) complex

Highly selective poly(vinyl chloride) (PVC) membrane electrode based on N-salicylidene-benzylamineato copper(II) complexes [Cu(SBA)₂] as new carriers towards thiocyanate-selective electrode was reported. The influence of membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. The resulting electrode exhibits anti-Hofmeister selectivity sequence: SCN⁻ > ClO₄⁻ > Sal⁻ > I⁻ > Br⁻ > NO₃⁻ > NO₂⁻ > SO₃²⁻ > H₂PO₄⁻ > Cl⁻ > SO₄²⁻, and a near-Nernstian potential linear range for thiocyanate from 1.0 × 10⁻¹ to 9.0 × 10⁻⁷ M with a detection limit of 7.0 10⁻⁷ M and a slope of , over a wide pH range of 3.0–9.0 in phosphate buffer solution at 20°C. The proposed electrode has a fast response time of about 5–10 s and can be used for at least 3 months without any considerable divergence in potential. The electrode was successfully applied to the determination of thiocyanate in waste water and human urine and saliva samples. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 3, pp. 293–299. The text was submitted by the authors in English.     

Kinetics of the Formation of the Blue Complex CrO(O2)2 Formed by Dichromate and H2O2 in Acid Solutions. A Stopped-Flow Investigation Using Rapid-Scan UV-VIS Detection

 The kinetics of the CrO(O₂)₂ formation by H₂O₂ and Cr₂O₇ ²⁻ in aqueous acidic media was measured at 293 ± 2 K in a pH range between 2.5 and 3.3. Using the stopped-flow method with rapid scan UV-VIS detection, the rate law of the formation of CrO(O₂)₂ was determined. For the media HClO₄, HNO₃ and CH₃COOH, the reaction order in the Cr₂O₇ ²⁻ concentration was found to be 0.5. For [H₂O₂] as well as for [H⁺], the reaction was first order in all acids used. In HCl and H₂SO₄ media the reaction was first order in Cr₂O₇ ²⁻. At T = 293 ± 2 K the rate constant for the formation of Cr(O)(O₂)₂ was found to be (7.3 ± 1.9) · 10² M^−3/2 s⁻¹ in HClO₄.     

Reduction of the photoexcited uranyl ion by water

Photooxidation of water by the uranyl ion was studied. Solutions of uranyl in 0.01–4.0M H₂SO₄, HClO₄, or 0.1–1.0M Na₂SO₄ and NaClO₄ containing “lacunary” heteropolytungstate (HPT) K₁₀P₂W₁₇O₆₁ or K₈SiW₁₁O₃₉ were irradiated with a nitrogen laser, a mercury or xenon lamp, or visible light. Spectrophotometric analysis showed that the irradiation results in the accumulation of U^IV. Simultaneously the formation of H₂O₂ proceeds. The quantum yield Φ of the reaction increases as the concentration of the acid or salt increases. For aerated solutions of 1M H₂SO₄ or 1M HClO₄, irradiation by light with λ=337.1 Φ is close to (1.5–2)·10⁻³. The irradiation of solutions with pH −4 for many days leads to an almost quantitative transformation of UO₂ ²⁺ into U^IV. When the irradiation was carried out in the absence of HPA, U^IV was not detected, although hydrogen peroxide was observed in the solution. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya. No. 2, pp. 282–287, February, 2000.     

Kinetics of the Formation of the Blue Complex CrO(O2)2 Formed by Dichromate and H2O2 in Acid Solutions. A Stopped-Flow Investigation Using Rapid-Scan UV-VIS Detection

Summary.  The kinetics of the CrO(O₂)₂ formation by H₂O₂ and Cr₂O₇ ²⁻ in aqueous acidic media was measured at 293 ± 2 K in a pH range between 2.5 and 3.3. Using the stopped-flow method with rapid scan UV-VIS detection, the rate law of the formation of CrO(O₂)₂ was determined. For the media HClO₄, HNO₃ and CH₃COOH, the reaction order in the Cr₂O₇ ²⁻ concentration was found to be 0.5. For [H₂O₂] as well as for [H⁺], the reaction was first order in all acids used. In HCl and H₂SO₄ media the reaction was first order in Cr₂O₇ ²⁻. At T = 293 ± 2 K the rate constant for the formation of Cr(O)(O₂)₂ was found to be (7.3 ± 1.9) · 10² M^−3/2 s⁻¹ in HClO₄. Corresponding author. E-mail: grampp@ptc.tu-graz.ac.at Received January 30, 2002; accepted (revised) June 5, 2002