Flow injection spectrophotometric determination of europium using chlortetracycline

A flow injection (FI) spectrophotometric determination of europium (III) is described, based on the complexation between europium (III), and chlortetracycline (CTC) in a Tris-buffer pH 8.0 medium. The resulting yellow-coloured complex is measured at its absorption maximum of 400 nm after 100 μl of sample or standard solution containing europium (III) are injected into the merged streams of CTC and Tris-buffer solutions. Optimum conditions for determining μg amounts of europium (III) are achieved by univariate method. Various types of reactors are also investigated. It is shown that the use of a single bead string reactor gives rise to the enhancement of peak height. A linear calibration curve over the range of 0.10-0.60 μg ml⁻¹ europium (III) is established with the regression equation (n=6) Y=34.93X+0.01 and the correlation coefficient of 0.9994 is obtained. A detection limit (3σ) of 0.01 μg ml⁻¹ of europium (III) and the relative standard deviation (R.S.D.) of 4.32% for determining 1.0 μg ml⁻¹ of europium (III) (n=7) are obtained. The recommended method has been applied to the quantitation of europium (III) in spiked water and stream sediment samples with average recoveries of 99.9 and 97.5%, respectively. The sampling rate is found to be 85 h⁻¹.     

X射线光电子能谱中的分峰处理

文章详细介绍了X射线光电子能谱分峰操作的流程,对谱图中单峰和多峰的荷电位移、数据平滑、背景扣除、谱峰确认和多高斯拟合操作的数学流程进行了图解。我们认为,具有足够连续宽度和强度的峰值处才可以被判定为峰;谱图中可以进行含量定量的谱峰强度应在背景涨落的10倍以上;最后得到的分峰结果,还应进行统计检验。     

二维卷积及其在色谱峰纯度鉴定中的应用

光电二极管阵列检测器与色谱仪的联用 ( HPLC- DAD)为复杂体系中多组分的定性定量分析提供了可能 .Savitzky等 [1]提出了以简单的卷积运算完成数值微分方法 .Gorry等 [2 ]曾以 Gram正交多项式替代幂级数拟合 ,让卷积技术可以覆盖到谱图包括起讫部分的任一点 .Edwards[3]与 Kuo[4 ]等提出的二维卷积法对处理和利用二变量数据矩阵具有普遍意义 ,但理论推导繁琐 .我们曾完善了推求二维卷积整数的普遍方法 [5] ,并研究和解决了一维和二维卷积中的信息丢失问题 [6 ,7] .本文提出了一种简化的求算二维卷积整数的方法 .理论推导表明 ,二维卷积…     

Flow injection analysis of doxycycline or chlortetracycline in pharmaceutical formulations with pulsed amperometric detection

A flow injection with pulsed amperometric detection for determination of doxycycline or chlortetracycline in pharmaceutical formulations is described. Doxycycline or chlortetracycline were studied at a gold rotating disk electrode with cyclic voltammetry as a function of pH of supporting electrolyte solution. The optimized PAD waveform parameters were obtained with a flow injection system. The optimized pulsed conditions of doxycycline were 1150 mV (versus Ag/AgCl reference electrode) detection potential (E_det) for 220 ms (150 ms delay time and 70 ms integration time), 1500 mV (versus Ag/AgCl reference electrode) oxidation potential (E_oxd) for 70 ms oxidation time (t_oxd) and 250 mV (versus Ag/AgCl reference electrode) reduction potentail (E_red) for 400 ms reactivation time (t_red). The optimized pulsed conditions of chlortetracycline were 1050 mV (versus Ag/AgCl reference electrode) detection potential (E_det) for 300 ms (200 ms delay time and 100 ms integration time), 1300 mV (versus Ag/AgCl reference electrode) oxidation potential (E_oxd) for 70 ms oxidation time (t_oxd) and 250 mV (versus Ag/AgCl reference electrode) reduction potentail (E_red) for 400 ms reactivation time (t_red). The optimized PAD waveform was applied to the determination of doxycycline hydrochloride and chlortetracycline hydrochloride standard solution and in pharmaceutical formulations. The linear dynamic ranges of doxycycline hydrochloride and chlortetracycline hydrochloride were 1 μM–0.1 mM. The sensitivity of this method was found to be 23 μA/mM for doxycycline hydrochloride and 33.76 μA/mM for chlortetracycline hydrochloride. The detection limit for both compounds is 1 μM. The doxycycline hydrochloride and chlortetracycline hydrochloride content in commercially available tablet dosage forms by the proposed method was comparable to those specified by the manufacturer.     

Reverse flow injection spectrophotometric determination of iron(III) using chlortetracycline reagent

A simple reversed flow injection colourimetric procedure for determining iron(III) was proposed. It is based on the reaction between iron(III) with chlortetracycline, resulting in an intense yellow complex with a suitable absorption at 435 nm. A 200 μl chlortetracycline reagent solution was injected into the phosphate buffer stream (flow rate 2.0 ml min⁻¹) which was then merged with iron(III) standard or sample in dilute nitric acid stream (flow rate 1.5 ml min⁻¹). Optimum conditions for determining iron(III) were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.5–20.0 μg ml⁻¹. The detection limit (3σ) and the quantification limit (10σ) were 0.10 and 0.82 μg ml⁻¹, respectively. The relatives standard deviation of the proposed method calculated from 12 replicate injections of 2.0 and 10.0 μg ml⁻¹ iron(III) were 0.43 and 0.59%, respectively. The sample throughput was 60 h⁻¹. The proposed method has been satisfactorily applied to the determination of iron(III) in natural waters.     

利用电流积分器和峰值保持单元改进固体电极上的多重峰测量和提高记录仪记录伏安图的精确性

本文推荐采用电流积分器和峰值保持(检测)器作为插入单元,以测量积分电量代替峰高测量,改进固体电极上的测量浓度范围。并采用峰值检测器提高记录仪的响应,使之适用于500～1000mV/s扫描速率下的伏安测定。本文以T(Ⅳ)作为例子证明上述优点。     

Simultaneous determination of 16 sulfonamides in animal feeds by UHPLC-MS-MS

A fast and sensitive method was developed for the simutaneous quantitative determination of 16 sulfonamides in animal feeds using ultra-high performance liquid chromatography tandem mass spectrometry (UHPLC-MS-MS). With the developed method, a feed sample can be analyzed in less than 2 h. A solid phase extraction method using acetonitrile and basic alumina column was developed to extract and purify sulfonamides from animal feeds. The analysis time can be greatly reduced with this method compared with previous reports. A linear range of 0.2 approximately 40 ng/mL (R(2) > 0.996) were obtianed for most of the compounds. The limits of quantification for all sulfonamides were in the range of 0.5 approximately 20 μg/kg. The high precision and accuracy of this method were represented by average recoveries ranging from 80% to 120% and coefficients of variation of less than 10% for spiked animal feed samples. The method is suitable for fast determination of sulfonamides in concentrates, premixes, and complete feeds.     

Silica-based monolithic columns versus conventional particle-packed columns for liquid chromatographic analysis of tetracycline, oxytetracycline and chlortetracycline

The rise of monolithic stationary phases offers to routine and research laboratories several advantages. In spite of their recent discovery, they have rapidly become highly popular separation media for liquid chromatography. Time reduction and economic reasons like e.g. a diminished use of mobile phase are the most important ones. At the same time, it was reported that these columns offer a faster and better separation. The aim of this article was to investigate the transferability of methods originally developed on conventional particle-packed C₁₈ columns (XTerra RP18 and Zorbax RX), onto the more recent monolithic columns. Both types, conventional particle-packed and monolithic columns, were able to separate tetracycline, oxytetracycline and chlortetracycline from their respective impurities with sufficient resolution, but showed remarkably shorter analysis times and lower backpressures, improving the lifetime of the column.     

Peak parking technique for the simultaneous determination of anions and cations

An ion chromatography method is described for the simultaneous determination of anions (Cl^–, NO₃^–, and SO₄^2–) and cations (Na⁺, NH₄⁺, K⁺, Mg²⁺, and Ca²⁺) using a single pump, a single eluent and a single detector. An anion-exchange column modified with chondroitin sulfate C facilitated the elution of the above three anions using 5 mM tartaric acid as the eluent in isocratic mode, whereas the same eluent facilitated the separation of the above five cations on a commercially-available cation-exchange column. The separation columns were connected in series via two six-port switching valves, so the required cation-exchange or anion-exchange separation could be carried out by selecting the appropriate positions for the switching valves. The separations were completed in 30 min.     

Development and validation of a liquid chromatographic/ tandem mass spectrometric method for determination of chlortetracycline, oxytetracycline, tetracycline, and doxycycline in animal feeds

A selective and accurate LC/MS/MS method for the simultaneous determination of chlortetracycline (CTC), oxytetracycline (OTC), tetracycline (TC), and doxycycline (DC) in animal feeds was developed. Samples were extracted with Na2EDTA-McIlvaine buffer and further purified with Oasis HLB SPE columns. The purified extract was separated on an Xbridge C18 column and detected by LC/MS/MS with positive electrospray ionization in the multiple reaction monitoring mode. This method provided average recoveries of 80.9 to 119.5%, with CVs of 1.7 to 9.8% in the range of 0.5 to 50 mg/kg CTC, OTC, TC, and DC in feeds, except the average recovery of CTC was 76.0%, with a CV of 14.6% in pig feed spiked with 0.5 mg/kg CTC. The linear ranges for the four TCs determined by LC/MS/MS ranged from 0.005 to 2.5 microg/mL with a linear correlation coefficient (R2) >0.99. The LOD and LOQ for CTC, OTC, TC, and DC in pig and poultry feeds ranged from 0.003 to 0.02 and 0.01 to 0.05 microg/g, respectively. The method was successfully applied for the analysis of 30 real feed samples, and no illegal use was detected.     

Broad specificity indirect competitive immunoassay for determination of nitrofurans in animal feeds

A generic hapten of nitrofurans was synthesized by derivatization of 5-nitrofurfural with diamine, and the hapten was coupled to carrier protein to prepare different immunogens and coating antigens by using diazotization method and glutaraldehyde method. The obtained novel polyclonal antibodies from immunized rabbits showed broad cross reactivity among seven nitrofurans. After assessment of four coating antigen/antibody combinations, an indirect competitive immunoassay was developed to simultaneously detect the seven nitrofurans in animal feeds. The limits of detection for these analytes were in the range of 5-16 μg kg⁻¹ depending on the compound. Recoveries from nitrofurans fortified blank feeds at levels of 30 and 100 ng g ⁻¹ were in a range of 82.6-108.4% with coefficients of variation lower than 11.4%. The immunoassay was further validated by a HPLC method and the two methods showed good correlation (r = 0.9924). Therefore, the proposed immunoassay could be used as a practical method to monitor the illicit use of nitrofurans in animal feeds.     

Simple screening method for the fast determination of clenbuterol in animal feeds

Summary A simple method for the determination of clenbuterol is described. It is extracted from the sample at pH 3 and then at pH 11, followed by partitioning the analyte into water at pH 3 and reextraction into ethyl acetate at pH 9. Clenbuterol is oxidized with KMnO₄ to clenbuteron for GC-determination. Recoveries for 0.01– 1.0 mg/kg were between 70% and 110% (standard deviation ±14%, n = 18).

---

Eine einfache Screening-Methode zur schnellen Bestimmung von Clenbuterol in tierischen Futtermitteln

     

A calculation method for the prediction of effective plate height in capillary gas chromatography

The effective plate height, h_eff, is considered to be a better measure of the efficiency of capillary column than the conventional plate height, h, in isothermal conditions. By using experimental data of 1-alcohols and n-alkanes, 2-ketones and 1-alkenes measured on capillary columns coated with non-polar stationary phases in isothermal and isobaric conditions, the peak width at half height is predicted with a function similar at that of adjusted retention time. The results obtained under different analytical conditions as the head pressure and the temperature of the column confirm the validity of the model, whose parameters are linear, and as a consequence a unique solution is obtained.     

Automated aflatoxin analysis of foods and animal feeds using immunoaffinity column clean-up and high-performance liquid chromatographic determination

A commercially available system is described for the fully automated clean-up and high-performance liquid chromatographic (HPLC) analysis of aflatoxins in foods and animal feeds. The system marketed primarily for handling solid-phase extraction columns has modified software to facilitate use with immunoaffinity columns. Sample extract clean-up followed by injection onto an HPLC column with post-column iodination and fluorescence detection is carried out completely unattended. A coefficient of variation of 5.1% for aflatoxin B1 analysis was obtained, and the accuracy of the system was demonstrated by the analysis of peanut butter certified reference material.     

Influence of the peak height distribution on separation performances: Discrimination factor and effective peak capacity

Summary A new index of performance of the chromatographic separation between two adjacent peaks, the discrimination factor, d₀, is defined. It is normalized between 0 and 1 and is directly and easily determined from the chromatogram. It does not depend on any assumption regarding peak shape, except that the peak profiles of individual sample components have a single mode. Its value depends on the relative heights of the two peaks as well as on their separation. The separation power of a chromatographic system is classically measured by its peak capacity, defined on the basis of constant resolution between adjacent peaks. A previously developed statistical theory of the composition of mixtures makes it possible to extend the concept of peak capacity by taking into account the peak height distribution in typical average chromatograms. A new parameter, the effective peak capacity, is defined for this purpose on the basis of a constant discrimination factor between adjacent peaks. It allows to take into account the distribution of peak heights in statistical theories of the evaluation of complex chromatograms and in the measurement of the limit of determination in quantitative analysis. The characteristics of the two new parameters, the discrimination factor and effective peak capacity, are discussed and compared with those of their classical homologs, resolution and peak capacity, in the case of gaussian component peaks of equal widths.     

Flow-injection chemiluminescence determination of chlortetracycline using on-line electrogenerated [Cu(HIO(6))(2)](5-) as the oxidant

A novel chemiluminescence (CL) flow system for the determination of chlortetracycline is described. It is based on the direct CL reaction of chlortetracycline and [Cu(HIO₆)₂]⁵⁻ in KOH medium. The unstable [Cu(HIO₆)₂]⁵⁻ was on-line electrogenerated by constant-current electrolysis. The CL intensity was linear with chlortetracycline concentration in the range of 0.1–100 μg ml⁻¹. The determination limit was 5.3×10⁻⁸ g ml⁻¹. The whole process could be completed in 1 min. The proposed method is suitable for automatic and continuous analysis, and has been applied satisfactorily to analysis of chlortetracycline in biological fluid.