含气量对空泡脉动特性影响的理论研究

分析了含气量对粘性液体中球形单空泡脉动特性的影响。研究结果表明：随着泡内初始含气量的增加,空泡达到最大泡半径的时间延长;空泡膨胀的最大泡半径、收缩的最小泡半径和脉动周期均随初始含气量的增加而增加;同时,空泡膨胀和溃灭时泡壁的运动速度均随空泡初始含气量的变化而变化。无论含气量如何,在空泡收缩到最小泡半径附近,泡壁运动速度（收缩或膨胀）要明显快于其在最大泡半径附近;此外,受液体粘性影响,空泡膨胀和收缩过程明显变缓。     

固壁面附近激光产生空泡脉动过程的实验研究

采用自行研制的光纤传感器研究了激光等离子体空泡在固壁面附近的脉动特性。实验获得了激光空泡三次膨胀到最大位置对应的波形图;并据此判定了激光空泡在脉动过程中对应的最大泡半径和溃灭周期;在此基础上结合空泡溃灭理论,计算了激光泡溃灭周期的延长因子κ。结果表明:随着脉动次数的增加,最大泡半径依次减小;随着作用激光能量的增大,最大泡半径,空泡溃灭周期的延长因子κ均增大;而无量纲参量的增大将导致延长因子的减小。所得到的延长因子同样可用于无限域流场。     

黏性液体中激光空泡脉动特性的理论和实验研究

通过自行研制的光偏转测试系统对黏性液体中激光空泡脉动特性进行了实验，获得了激光等离子体空泡前两次脉动全过程，从而判定了空泡在脉动过程中对应的最大和最小泡半径；并将不同黏性系数下空泡脉动结果与基于空泡溃灭理论的计算结果进行了对比.结果表明：液体黏性对空泡生存周期、空泡半径，以及泡壁的运动速度等均有影响.受液体黏性影响，空泡膨胀或收缩过程明显变缓，其相应的生存周期也越长.这一研究结果不仅可促进空化研究的深入，也可为合理利用空化现象提供参考. 关键词： 激光泡 脉动特性 黏性 光纤传感器     

表面张力对固壁旁空泡运动特性影响的理论和实验研究

表面张力是影响空泡脉动及空蚀的一个重要因素.对五种不同表面张力液体中空泡脉动（膨胀和收缩）过程进行了研究,并将实验结果与基于空泡生长和溃灭理论的计算结果进行了对比.实验中,用激光作为测试光源,采用光偏转测试系统研究了不同表面张力液体中空泡泡壁运动规律及泡壁速度的变化.结果表明：表面张力对空泡膨胀过程起抑制作用,故液体表面张力愈大,空泡能达到的最大直径越小;表面张力对空泡的收缩过程则起加速作用,液体表面张力愈大,收缩越迅速,空泡泡壁运动速度越大,其所产生的瞬时溃灭压强越大,空化效果越好. 关键词： 表面张力 空泡 光偏转     

含气量对黏性液体中空泡脉动特性的影响

采用自行研制的高灵敏度光偏转测试系统,研究黏性液体中激光空泡脉动特性.判定了空泡两次脉动对应的最大和最小泡半径,进而计算了激光空泡在前两次脉动过程中泡内的含气量.研究表明：泡内含气量对泡脉动特性有较大影响.随着脉动次数的增加,空泡泡内含气量增大.空泡最大泡半径随含气量的增加而增大.此外,受液体黏性影响,空泡膨胀和收缩过程明显变缓. 关键词： 含气量 黏性 激光空泡 脉动特性     

含气量对激光空泡在刚性壁面空蚀的影响

采用强脉冲激光器设计液体环境下刚性壁面空蚀实验平台,改变液体中含气量,利用高速相机观察不同含气量条件下激光空泡在壁面附近的脉动过程,并对刚性壁面造成的空蚀结果进行了观测。实验研究发现,随着液体中相对空气含量的提高,激光空泡脉动的最大尺寸增大,空泡的膨胀运动变剧烈,溃灭运动速度降低,空泡的溃灭强度降低,从而影响到溃灭冲击波和壁面微射流对刚性壁面的冲击速度,减弱了壁面空蚀,而液体中含气量的提高能够降低激光空泡对刚性壁面的空蚀程度。     

激光烧蚀水下金属产生冲击波和空泡效应的研究

采用自行研制的高灵敏度光束偏转测试系统,对脉冲激光烧蚀水下金属产生的等离子体冲击波和空泡效应进行了实验研究。实验得到了激光等离子体冲击波的传播规律、冲击波与激光空泡的分离过程、空泡的脉动特性以及空泡溃灭冲击波的形成机制。结果表明,空泡最大和最小泡径、振荡周期均随着脉动次数的增加呈减小趋势,且减小幅度较大。最小收缩泡径由泡能和腔内含气量共同决定。在同一次脉动过程中,空泡膨胀所需的时间明显大于收缩所需的时间。     

壁面附近激光空泡溃灭的空蚀特性

为分析空泡在壁面附近溃灭导致的冲击波和射流特性,提出将激光空化、高速摄影技术应用于激光空泡的空蚀研究。建立了壁面附近激光空泡的产生、微调控制及高速摄影测量实验平台。采用高速摄影技术对不同液体、不同γ参量条件下空泡脉动的外形特征、溃灭冲击波和溃灭射流等参量进行了测量。结果表明,壁面的存在弱化了空泡溃灭时的收缩程度,空泡溃灭时的冲击波和射流对壁面的破坏作用存在着此消彼长,相互竞争的关系;空泡在壁面附近脉动时,回弹泡的溃灭对壁面也可产生较强的破坏作用;液体的粘性增大有助于空泡表面维持稳定,减缓空泡溃灭时泡壁的运动速度。     

含气量对液体中空泡声波频谱特性的影响

通过压电陶瓷（PZT）水听器获取了液体中激光空泡脉动辐射的声波,并计算了激光空泡在第1次脉动过程中泡内的含气量,结合空泡含气量对空泡最大半径及脉动周期影响的分析,进而分析了含气量对空泡声波频谱特性的影响。分析结果表明:激光空泡第1次脉动过程中泡内的含气量随着作用激光能量的增加而增加,含气量的多少将直接影响空泡运动的剧烈程度;含气量越多,空泡脉动越缓慢,脉动周期越长,空泡脉动辐射声波的峰值频率有向低频移动的趋势。     

10-6-10-4m2/s黏度液体中靶受力学作用的测试与分析

通过自行研制的光纤传感器对不同黏度液体中材料靶后的力学作用进行研究,获得了液体黏度变化对等离子体烧蚀力、射流冲击力及空泡生存周期的影响. 实验结果表明:液体黏度相同时,靶材所受冲击力幅值随作用激光能量的增加单调上升;液体黏度增加时,靶材所受的冲击力减小,靶材的空化空蚀程度亦减小;受液体黏度增大的影响,空泡膨胀或收缩过程减缓,相应的生存周期也增大. 此外,对空泡溃灭周期公式进行修正,结果表明修正后的理论估算值与实验值的一致性较好.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.