Mass transfer from theophylline hydrogels of a‐PVA/H2O and a‐PVA/NaCl/H2O system on heating

Theophylline hydrogels of atactic‐poly(vinyl alcohol) (a‐PVA)/H₂O and a‐PVA/NaCl/H₂O systems were prepared followed by cyclic freezing (?30°C for 16 hr)–thawing (at room temperature for 8 hr) and one cycle gelation (at ?20°C for 24 hr) processes, respectively. In order to prepare xerogels (dried hydrogels) of these hydogel systems, an apparently first‐order mass transfer phenomenon of water as evaporation was observed for a‐PVA/H₂O hydrogel system, while heating at 60°C. The rate of evaporation decreased with increasing time in hyperbolic fashion. The total surface area (both lateral and two end surfaces of hydrogel matrix disc) decreased linearly for the first 90 min and thereafter had a tendency towards the steady‐state. The total mass flux showed time dependent linear reduction phenomenon, which is a characteristic physical behavior for these hydrogel systems on heat treatment. When NaCl was included in a‐PVA/H₂O system mass transfer of water followed fourth‐order polynomial. But in consideration of a comparative study, sustained mass transfer was found from the hydrogel matrices of a‐PVA/H₂O/NaCl system (gelation at ?20°C). Copyright © 2003 John Wiley & Sons, Ltd.     

Formation Mechanism of a Silane‐PVA/PVAc Complex Film on a Glass Fiber Surface

Mechanical properties of glass fiber reinforced composite materials are affected by fiber sizing. A complex film formation, based on a silane film and PVA/PVAc (polyvinyl alcohol/polyvinyl acetate) microspheres on a glass fiber surface is determined at 1) the nanoscale by using atomic force microscopy (AFM), and 2) the macroscale by using the zeta potential. Silane groups strongly bind through the Si? O? Si bond to the glass surface, which provides the attachment mechanism as a coupling agent. The silane groups form islands, a homogeneous film, as well as empty sites. The average roughness of the silanized surface is 6.5 nm, whereas it is only 0.6 nm for the non‐silanized surface. The silane film vertically penetrates in a honeycomb fashion from the glass surface through the deposited PVA/PVAc microspheres to form a hexagonal close pack structure. The silane film not only penetrates, but also deforms the PVA/PVAc microspheres from the spherical shape in a dispersion to a ellipsoidal shape on the surface with average dimensions of 300/600 nm. The surface area value S_a represents an area of PVA/PVAc microspheres that are not affected by the silane penetration. The areas are found to be 0.2, 0.08, and 0.03 μm² if the ellipsoid sizes are 320/570, 300/610, and 270/620 nm for silane concentrations of 0, 3.8, and 7.2 μg mL^?1, respectively. The silane film also moves PVA/PVAc microspheres in the process of complex film formation, from the low silane concentration areas to the complex film area providing enough silane groups to stabilize the structure. The values for the residual silane honeycomb structure heights (H_a) are 6.5, 7, and 12 nm for silane concentrations of 3.8, 7.2, and 14.3 μg mL^?1, respectively. The pH‐dependent zeta‐potential results suggest a specific role of the silane groups with effects on the glass fiber surface and also on the PVA/PVAc microspheres. The non‐silanized glass fiber surface and the silane film have similar zeta potentials ranging from ?64 to ?12 mV at pH’s of 10.5 and 3, respectively. The zeta potentials for the PVA/PVAc microspheres on the glass fiber surface and within the silane film significantly decrease and range from ?25 to ?5 mV. The shapes of the pH‐dependent zeta potentials are different in the cases of silane groups over a pH range from 7 to 4. A triple‐layer model is used to fit the non‐silanized glass surface and the silane film. The value of the surface‐site density for Γ_Xglass and Γ_Xsilane, in which X denotes the Al? O? Si group, differs by a factor of 10^?4, which suggests an effective coupling of the silane film. A soft‐layer model is used to fit the silane‐PVA/PVAc complex film, which is approximated as four layers. Such a simplification and compensation of the microsphere shape gives an approximation of the relevant widths of the layers as the follows: 1) the layer of the silane groups makes up 10 % of the total length (27 nm), 2) the layer of the first PVA shell contributes 30 % to the total length (81 nm), 3) the layer of the PVAc core contributes 30 % to the total length (81 nm), and finally 4) the layer of the second PVA shell provides 30 % of the total length (81 nm). The coverage simulation resulted in a value of 0.4, which corresponds with the assumption of low‐order coverage, and is supported by the AFM scans. Correlating the results of the AFM scans, and the zeta potentials sheds some light on the formation mechanism of the silane‐PVA/PVAc complex film.     

Electro‐ and photoconductive properties of the PVA/PAN‐I2 blends

The electrical conductivity of poly(vinylalcohol)/polyaniline‐iodine blend (PVA/PAN‐I₂) prepared by solution process was investigated. The FTIR spectroscopy revealed a structural change of both shape and intensity of the polyaniline (PAN) bands after doping with iodine, indicating the formation of a charge transfer complex. The J‐V curves for pure PAN; PAN‐I₂ and PVA/PAN‐I₂ film obey the ohm law at lower voltages, deviate from the linear response at higher voltages and finally display the breakdown behavior. The PVA/PAN‐I₂ exhibit photoconductivity by UV/visible irradiation as well as oscillations that may be attributed to a nonlinear behavior of the blend.     

Synthesis and characterization of new organic–inorganic nanohybrid film (TBA)PWFe/PVA/CTS as an efficient and reusable amphiphilic catalyst for ODS of real fuel

In this work, we report a new catalytic oxidative desulfurization (CODS) system based on (TBA)PWFe/PVA/CTS nanohybrid film as a highly active catalyst. The nanohybrid material was successfully fabricated by the composition of tetra (n‐butyl) ammonium salt of Fe‐substituted phosphotungstate, ((n‐C₄H₉)₄N)₄[PW₁₁Fe(H₂O)O₃₉] abbreviated as (TBA)PWFe, polyvinyl alcohol (PVA), and chitosan (CTS). The composite was characterized using various analytical techniques including FT‐IR, UV–vis, XRD, and SEM. The results revealed the hydrogen‐bonding interaction between inorganic (TBA)PWFe clusters and organic polymers. The catalytic activity of (TBA)PWFe/PVA/CTS was evaluated in the CODS of real gas oil. Also, the solutions of heterocyclic thiophenic compounds (HTCs) in n‐heptane were tasted as simulated fuels. It was found that the removal efficiency of HTCs in the presence of (TBA)PWFe/PVA/CTS catalyst reached as high as 95% at 60 °C after 2 h. The significant catalytic performance of the nanohybrid film might be attributed to its amphiphilicity and multifunctional active sites, which enhances adsorption and oxidation of sulfur compounds. Moreover, the (TBA)PWFe/PVA/CTS composite can be easily recovered and reused by simple filtration, making it a suitable catalyst for cleaner processing.     

Polypyrrole/poly(N‐isopropylacrylamide‐co‐acrylic acid) thermosensitive and electrically conductive composite microgels

The electrically conductive polypyrrole/dodecylbenzene sulfonic acid/poly(N‐isopropylacrylamide‐co‐acrylic acid) (PPy/DBSA/poly(NIPAAm‐co‐AA)) composite microgels were synthesized by a chemical oxidation of pyrrole in the presence of DBSA as the primary dopant, and poly(NIPAAm‐co‐AA) microgels as the polymeric codopant and template, in which APS was used as the oxidant. It was proposed to prepare “intelligent” polymer microgel particles containing both thermosensitive and electrically conducting properties. The polymerization of pyrrole took place directly inside the microgel networks, leading to formation of composite microgels and the morphology was observed by transmission electron microscope. PPy particles interacted strongly with microgels, as the acid groups of microgels acted as the polymeric codopant. The composite microgels thus formed showed electrically conducting behavior dependent on humidity and temperature. At temperatures lower than lower critical solution temperature, the conductivity decreased with increasing the humidity and a small hysteresis phenomenon was observed. The hysteresis became indistinct when temperature was near volume phase transition temperature. However, after the treatment of high temperature and high humidity, the conductivity increased surprisingly due to the structure reorganization inside the composite microgels. The distinctive functionality of the PPy composite microgels was expected to be utilized in many attractive applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1648–1659, 2006     

Dynamics of cyclodimerization and viscoelasticity of photo‐crosslinkable PVA

We investigated the interfacial properties of poly(vinyl alcohol) carrying UV‐crosslinkable pendant quaternized stilbazole (styrylpyridinium), PVA‐SbQ. The extent and dynamics of PVA‐SbQ cyclodimerization reactions and crosslinking induced by UV irradiation were monitored in situ and in real time by quartz crystal microgravimetry (QCM). Sensograms reflecting time‐dependent changes in density and viscoelasticity of crosslinking films followed a Boltzmann sigmoidal model, depending on precursor film composition and irradiation power. The shifts in QCM frequency and energy dissipation upon PVA‐SbQ cyclodimerization correlated with three photo‐crosslinking phases involving soft‐to‐rigid transitions, namely, induction (initiation), main crosslinking (interaction), and termination. PVA‐SbQ films crosslinked to different degree were used as protein carriers and a slower release profile was determined for the films that underwent more extensive crosslinking. Overall, this study demonstrates for the first time the dynamics of PVA‐SbQ crosslinking and its impact in system viscoelasticity and protein release. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 345–355     

An analytical method for measuring α‐amylase activity in starch‐containing foods

The quality of starch‐containing foods may be significantly impaired by contamination with very small amounts of α‐amylase, which can enzymatically hydrolyze the starch and cause viscosity loss. Thus, for quality control, it is necessary to have an analytical method that can measure low amylase activity. We developed a sensitive analytical method for measuring the activity of α‐amylase (from Bacillus subtilis) in starch‐containing foods. The method consists of six steps: (1) crude extraction of α‐amylase by centrifugation and filtration; (2) α‐amylase purification by desalting and anion‐exchange chromatography; (3) reaction of the purified amylase with boron‐dipyrromethene (BODIPY)‐labeled substrate, which releases a fluorescent fragment upon digestion of the substrate, thus avoiding interference from starch derivatives in the sample; (4) stopping the reaction with acetonitrile; (5) reversed‐phase solid‐phase extraction of the fluorescent substrate to remove contaminating dye and impurities; and (6) separation and measurement of BODIPY fluorescence by HPLC. The proposed method could quantify α‐amylase activities as low as 10 mU/mL, which is enough to reduce the viscosity of starch‐containing foods. Copyright © 2012 John Wiley & Sons, Ltd.     

Photoregulated Sol‐Gel Transition of Novel Azobenzene‐Functionalized Hydroxypropyl Methylcellulose and Its α‐Cyclodextrin Complexes

Summary: Novel azobenzene‐functionalized hydroxypropyl methylcellulose (AZO‐HPMC) polymers and their α‐cyclodextrin (α‐CD) complexes have been prepared. These polymers show interesting sol‐gel transition behavior in aqueous solutions. In the absence of α‐CD, the gelation temperature increases after UV irradiation, while in the presence of α‐CD, the gelation temperature decreases after UV irradiation. The difference in the gelation temperatures between the trans and cis samples of AZO‐HPMC opens a wide operating window for reversible regulation of the sol‐gel transition behavior by photoirradiation.

The UV‐induced cis/trans isomerism of azobenzene‐functionalized hydroxypropyl methylcellulose and its α‐cyclodextrin complexes.     

Synthesis of thermo‐responsive microgels in supercritical carbon dioxide using ethylene glycol dimethacrylate as a cross‐linker

Herein, we report the preparation of thermo‐responsive polymers in a green medium. The white, dry, fine powders were obtained directly from the cross‐linking polymerization of N‐isopropylacrylamide (NIPA) in supercritical carbon dioxide (scCO₂) at pressures ranging from 10 to 28 MPa utilizing ethylene glycol dimethacrylate (EGDMA) as a cross‐linker. The effects of reaction pressure, cross‐linker ratio, initiator concentration, and reaction time were investigated. In the presence of this cross‐linker (26.4% w/w), much smaller poly(N‐isopropylacrylamide) (PNIPA) microgels (<0.2 µm diameter) were formed, and it was shown that the particle size and the morphology of the polymer were strongly dependent on the cross‐linker ratio in scCO₂. Copyright © 2009 John Wiley & Sons, Ltd.     

Deswelling comparison of temperature‐sensitive poly(N‐isopropylacrylamide) microgels containing functional ?OH groups with different hydrophilic long side chains

Two monomers containing functional ? OH groups with different hydrophilic long side chains (viz., triethyleneglycol methacrylate (TREGMA) and polyethyleneglycol methacrylate (PEGMA)) were selected to modify the swelling/deswelling behavior of poly(N‐isopropylacrylamide) (pNIPAM) microgels. Dynamic scattering technique, turbidimetric method, and differential scanning calorimetry (DSC) were employed to investigate the deswelling behavior of the microgels. Experimental results show that the two series of microgels are identical in that incorporation of hydrophilic chains containing ? OH groups causes the volume‐phase transition temperature (VPTT) of pNIPAM microgels to shift to higher temperature; the more hydrophilic the side chains, the more the VPTTs shift. Although PEGMA are more effective in elevating the VPTTs of pNIPAM microgels than TREGMA, p(NIPAM‐co‐TREGMA) microgels show better deswelling properties than p(NIPAM‐co‐PEGMA) microgels, i.e., they have much larger deswelling ratios (α) and display less continuous volume‐phase transition. The VPTTs of the modified microgels can be modulated to well close to the normal body temperature of human beings. These characteristics along with the functional ? OH groups they contain make the microgels competitive candidates for biomaterials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3575–3583, 2005     

Charge‐derivatized amino acids facilitate model studies on protein side‐chain modifications by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry

The α‐amino groups of histidine and lysine were derivatized with p‐carboxylbenzyltriphenylphosphonium to form the pseudo dipeptides, PHis and PLys, which can be sensitively detected by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI‐TOFMS) due to the fixed positive charge of the phosphonium group. Detection limits of PHis and PLys by MALDI‐TOFMS were both 30 fmol with a signal‐to‐noise ratio of 5:1. These pseudo dipeptides were excellent surrogates for His‐ or Lys‐containing peptides in model reactions mimicking proteins with reactive electrophiles, prominently those generated by peroxidation of polyunsaturated fatty acids including 4‐hydroxy‐2(E)‐nonenal (HNE), 4‐oxo‐2(E)‐nonenal (ONE), 2(E)‐octenal, and 2(E)‐heptenal. An air‐saturated solution of linoleic acid (d₀:d₅ = 1:1) was incubated in the presence of Fe(II) and ascorbate with these two pseudo dipeptides, and the reaction products were characterized by MALDI‐TOFMS and liquid chromatography/electrospray ionization mass spectrometry (LC/ESI‐MS). By using PHis and PLys, the previously reported ONE‐derived His‐furan adduct was detected along with evidence for a cyclic α,β‐unsaturated ketone. A dimer formed from ONE was found to react with PHis through Michael addition. Alkenals were found to form two novel adducts with PLys. 2(E)‐Octenoic acid–His Michael adduct and N^ε‐pentanoyllysine were identified as potential protein side‐chain adducts modified by products of linoleic acid peroxidation. In addition, when PHis or PLys and AcHis or BocLys were exposed to the linoleic acid peroxidation, an epoxy‐keto‐ocatadecenoic acid mediated His–His cross‐link was detected, along with the observation of a His–ONE/9,12‐dioxo‐10‐dodecenoic acid–Lys derived pyrrole cross‐link. Copyright © 2009 John Wiley & Sons, Ltd.     

The controlled release behavior and pH‐ and thermo‐sensitivity of alginate/poly(vinyl alcohol) blended hydrogels

Poly(vinyl alcohol) (PVA) was blended with sodium alginate (Alg) in various ratios and crosslinked with calcium chloride and made into hydrogel membranes. The dependence of the swelling behavior of these Alg‐Ca/PVA hydrogels on pH was investigated. The temperature‐dependent swelling behavior of the semi‐interpenetrating network (semi‐IPN) hydrogels was examined at temperatures from 2 to 45°C and the enthalpy of mixing (ΔH_mix) was determined at various temperatures. The molecular structure of the hydrogels was studied by infrared spectroscopy and their water structure in the semi‐IPN hydrogels was measured by differential scanning calorimetry (DSC). The influence of Ca²⁺ content on the network structure of Alg‐Ca/PVA hydrogels was investigated in terms of the compressive elastic modulus, effective crosslinking density, and the polymer–solvent interaction parameter based on the Flory theory. The loading of alizarin red S (ARS) followed the Langmuir isotherm mechanism and the release kinetics of ARS from the Alg‐Ca/PVA hydrogels followed the Fickian diffusion mechanism. Copyright © 2008 John Wiley & Sons, Ltd.     

Electrochemical Study of the Interactions of DNA with Redox‐Active Molecules Based on the Immobilization of dsDNA on the Sol‐Gel Derived Nano Porous Hydroxyapatite‐Polyvinyl Alcohol Hybrid Material Coating

A novel type of sol‐gel inorganic‐organic hybrid material coated on glassy carbon electrode used for immobilization of double‐stranded DNA (dsDNA) and study of dsDNA with redox‐active molecules was developed. The hybrid material coating was produced by sol‐gel method with nano hydroxyapatite (HAp)‐polyvinyl alcohol (PVA). The optimum composition of the hybrid material was first examined, and the morphology of the nano HAp‐PVA coatings was investigated with the help of Scanning Electron Microscope (SEM). DsDNA was immobilized in/on the nano HAp‐PVA hybrid coatings by adsorption and the characteristics of the dsDNA/HAp‐PVA/GCE were studied by cyclic voltammetry (CV) using the probes of Co(phen) and Fe(CN) . The results indicate that the dsDNA can be immobilized on the nano porous HAp‐PVA coating effectively and its stability can satisfy the necessity of study on the interactions of dsDNA with redox‐active molecules on the electrode surface. Co(bpy) and Co(phen) were used as the model molecule to study the interactions of dsDNA with redox‐active molecules. Information such as ratio (K_Ox/K_Red) of the binding constant for the oxidized and reduced forms of a bound species, interaction mode, including change in the mode of interaction, and “limiting” ratio K /K at zero ionic strength (μ) can be obtained using dsDNA/HAp‐PVA/GCE with about 2 μg of DNA samples.     

Physical properties of diblock methylcellulose derivatives with regioselective functionalization patterns: First direct evidence that a sequence of 2,3,6‐tri‐O‐methyl‐glucopyranosyl units causes thermoreversible gelation of methylcellulose

This article describes detailed structure‐property relationships of 5 regioselectively methylated celluloses and 10 diblock cellulose derivatives with regioselective functionalization patterns: methyl 2,3,6‐tri‐O‐ ( 1 , 236MC), methyl 2,3‐di‐O‐ ( 2 , 23MC), methyl 2,6‐di‐O‐ ( 3 , 26MC), methyl 3‐O‐ ( 4 , 3MC), methyl 6‐O‐methyl‐cellulosides ( 5 , 6MC), methyl β‐D‐glucopyranosyl‐(1→4)‐2,3,6‐tri‐O‐methyl‐ ( 6 , G‐236MC), methyl β‐D‐glucopyranosyl‐(1→4)‐2,3‐di‐O‐methyl‐ ( 7 , G‐23MC), methyl β‐D‐glucopyranosyl‐(1→4)‐2,6‐di‐O‐methyl‐ ( 8 , G‐26MC), methyl β‐D‐glucopyranosyl‐(1→4)‐3‐O‐methyl‐ ( 9 , G‐3MC), methyl β‐D‐glucopyranosyl‐(1→4)‐6‐O‐methyl‐ ( 10 , G‐6MC), methyl β‐D‐glucopyranosyl‐(1→4)‐β‐D‐glucopyranosyl‐(1→4)‐2,3,6‐tri‐O‐methyl‐ ( 11 , GG‐236MC), methyl β‐D‐glucopyranosyl‐(1→4)‐β‐D‐glucopyranosyl‐(1→4)‐2,3‐di‐O‐methyl‐ ( 12 , GG‐23MC), methyl β‐D‐glucopy‐ranosyl‐(1→4)‐β‐D‐glucopyranosyl‐(1→4)‐2,6‐di‐O‐methyl‐ ( 13 , GG‐26MC), methyl β‐D‐glucopyranosyl‐(1→4)‐β‐D‐glucopyranosyl‐(1→4)‐3‐O‐methyl‐ ( 14 , GG‐3MC), and methyl β‐D‐glucopyranosyl‐(1→4)‐β‐D‐glucopyranosyl‐(1→4)‐6‐O‐methyl‐cellulosides ( 15 , GG‐6MC). Surface tension, differential scanning calorimetry, fluorescence, and dynamic light scattering measurements of aqueous solutions of compounds 1 – 15 revealed that there was no relationship between aggregation behaviors and gel formation, gelation occurred only when the hydrophobic environments formed by hydrophobic interactions between the sequences of 2,3,6‐tri‐O‐methyl‐glucopyranosyl units upon heating. The diblock structure consisting of cellobiosyl block and approx. ten 2,3,6‐tri‐O‐methyl‐glucopyranosyl units was of crucial importance for thermoreversible gelation of methylcellulose. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1539–1546, 2011     

Selenium‐Modified Microgels as Bio‐Inspired Oxidation Catalysts

Active colloidal catalysts inspired by glutathione peroxidase (GPx) were synthesized by integration of catalytically active selenium (Se) moieties into aqueous microgels. A diselenide crosslinker (Se X‐linker) was successfully synthesized and incorporated into microgels through precipitation polymerization, along with the conventional crosslinker N,N′‐methylenebis(acrylamide) (BIS). Diselenide bonds within the microgels were cleaved through oxidation by H₂O₂ and converted to seleninic acid whilst maintaining the intact microgel microstructure. Through this approach catalytically active microgels with variable amounts of seleninic acid were synthesized. Remarkably, the microgels exhibited higher catalytic activity and selectivity at low reaction temperatures than the molecular Se catalyst in a model oxidation reaction of acrolein to acrylic acid and methyl acrylate.     

Physicochemical characterization and drug release properties of PDMAEMA/OSA Semi‐IPN hydrogels with microporous structure

A new poly(2‐(dimethylamino) ethyl methacrylate)/oxidized sodium alginate (PDMAEMA) semi‐interpenetrating network (Semi‐IPN) hydrogel with microporous structure was prepared by using PDMAEMA microgels as an additive during the polymerization/crosslinking process. The interior morphology characterized by scanning electron microscopy showed the Semi‐IPN hydrogels have different pore sizes by changing the amount of microgels. The hydrogels were also characterized by using Fourier transform infrared and DSC. The swelling behaviors of hydrogels indicated that the hydrogels have excellent pH and temperature sensitivity. Bovine serum albumin was entrapped in the hydrogels and the in vitro drug release profiles were established in different buffer solutions at various temperatures. The release behaviors of the model drug were dependent on the pore size of the hydrogels and environmental temperature/pH, which suggested that these materials have potential application as intelligent drug carriers. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis,characterization, and swelling behaviors of chitosan‐g‐poly(acrylic acid)/poly(vinyl alcohol) semi‐IPN superabsorbent hydrogels

A series of granulated semi‐interpenetrating polymer network (semi‐IPN) superabsorbent hydrogels composed of chitosan‐g‐poly(acrylic acid) (CTS‐g‐PAA) and poly(vinyl alcohol) (PVA) were prepared by solution polymerization using ammonium persulfate (APS) as an initiator and N,N′‐methylenebisacrylamide (MBA) as a crosslinker. The effects of reaction conditions such as the concentration of MBA, the weight ratio of AA to CTS, and the content of PVA on water absorbency were investigated. Infrared (IR) spectra and differential scanning calorimetry (DSC) analyses confirmed that AA had been grafted onto CTS backbone, and PVA semi‐interpenetrating into CTS‐g‐PAA networks. SEM analyses indicated that CTS‐g‐PAA/PVA has improved porous surface and PVA was uniformly dispersed in CTS‐g‐PAA network. The semi‐IPN hydrogel containing 10 wt% PVA shows the highest water absorbency of 353 and 53 g g^?1 in distilled water and 0.9 wt% NaCl solution, respectively. Swelling behaviors revealed that the introduction of PVA could improve the swelling rate and enhance the pH stability of the superabsorbent hydrogel. Copyright © 2009 John Wiley & Sons, Ltd.     

Fabrication of poly(vinyl alcohol)‐graphene quantum dots coated with poly(3,4‐ethylenedioxythiophene) for supercapacitor

Conducting nanofiber composed of poly(vinyl alcohol) (PVA), graphene quantum dots (GQDs) and poly(3,4‐ethylenedioxythiophene) (PEDOT) was prepared for symmetrical supercapacitor through electrospinning and electropolymerization techniques. The formation of PVA nanofibers with the addition of GQDs was excellently prepared with the average diameter of 55.66 ± 27 nm. Field emission scanning electron microscopy images revealed that cauliflower‐like structure of PEDOT was successfully coated on PVA‐GQD electrospun nanofibers. PVA‐GQD/PEDOT nanocomposite exhibited the highest specific capacitance of 291.86 F/g compared with PVA/PEDOT (220.73 F/g) and PEDOT (161.48 F/g). PVA‐GQD/PEDOT also demonstrated a high specific energy and specific power of 16.95 and 984.48 W/kg, respectively, at 2.0 A/g current density. PVA‐GQD/PEDOT exhibited the lowest resistance of charge transfer (R_ct) and equivalent series resistance compared with PEDOT and PVA/PEDOT, indicating that the fast ion diffusion between the electrode and electrolyte interface. PVA‐GQD/PEDOT nanocomposite also showed an excellent stability with retention of 98% after 1000 cycles. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 50–58     

Thermosensitive and control release behavior of poly (N‐isopropylacrylamide‐co‐acrylic acid) latex particles

In this work, poly(N‐isopropylacrylamide‐co‐acrylic acid) (poly(NIPAAm‐AA)) copolymer latex particles (microgels) were synthesized by the method of soapless emulsion polymerization. Poly(NIPAAm‐AA) copolymer microgels have the property of being thermosensitive. The concentration of acrylic acid (AA) and crosslinking agent N,N′‐methylenebisacrylamide were important factors to influence the lower critical solution temperature (LCST) of poly(NIPAAm‐AA) microgels. The effects of AA and crosslinking agent on the swelling behavior of poly(NIPAAm‐AA) microgels were also studied. The poly(NIPAAm‐AA) copolymer microgels were then used as a thermosensitive drug carrier to load caffeine. The effects of concentration of AA and crosslinking agent on the control release of caffeine were investigated. How the AA content and crosslinking agent influenced the morphology and LCST of the microgels was discussed in detail. The relationship of morphology, swelling, and control release behavior of these thermosensitive microgels was established. A new scheme was proposed to interpret the control release of the microgels with different morphological structures. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5734–5741, 2008     

Screening and separation of α‐amylase inhibitors from Solanum nigrum with amylase‐functionalized magnetic graphene oxide combined with high‐speed counter‐current chromatography

A screening method using α‐amylase‐functionalized magnetic graphene oxide combined with high‐speed counter‐current chromatography was proposed and utilized to screen and separate α‐amylase inhibitors from extract of Solanum nigrum . The α‐amylase‐functionalized magnetic graphene oxide was characterized and found to demonstrate satisfactory structure, magnetic response (24.5 emu/g), and reusability (retained 90% of initial activity after five cycles). The conditions for the screening with α‐amylase functionalized magnetic graphene oxide were optimized and set at pH 7.0 and 25°C. As a result, two potent flavonoid compounds, apigenin‐7‐O‐glucuronide ( 1 ) and astragalin ( 2 ), were separated and collected through high‐speed counter‐current chromatography and subjected to high‐performance liquid chromatography analysis with purity higher than 90% (according to HPLC data), which were identified as α‐amylase inhibitors. These results suggested that utilization of α‐amylase functionalized magnetic graphene oxide in the rapid screening and isolation bioactive compounds from complex natural products is a feasible and environmentally friendly method.