Surface‐enhanced Raman scattering of 4‐mercaptopyridine on sub‐monolayers of α‐Fe2O3 nanocrystals (sphere,spindle, cube)

We report surface‐enhanced Raman scattering (SERS) spectra from 4‐mercaptopyridine (4‐Mpy) adsorbed on sub‐monolayers of α‐Fe₂O₃ nanocrystals (sphere, spindle, cube). The maximum enhancement factor has been estimated to be about 10⁴ compared to that of 4‐Mpy in solution. A possible mechanism has been proposed that the charge transfer between the α‐Fe₂O₃ nanocrystals and the 4‐Mpy molecules is most likely responsible for the observed enhancement of Raman intensity of adsorbed 4‐Mpy molecules as surface plasmon resonances have not occurred. Copyright © 2009 John Wiley & Sons, Ltd.     

Theoretical elucidation of the origin of surface‐enhanced Raman spectra of PCB52 adsorbed on silver substrates

To better understand experimentally observed surface‐enhanced Raman Scattering (SERS) of polychlorinated biphenyls (PCBs) adsorbed on nanoscaled silver substrates, a systematic theoretical study was performed by carrying out density functional theory and time‐dependent density functional theory calculations. 2,2′,5,5′‐tetrachlorobiphenyl (PCB52) was chosen as a model molecule of PCBs, and Ag_n (n = 2, 4, 6, and 10) clusters were used to mimic active sites of substrates. Calculated normal Raman spectra of PCB52–Ag_n (n = 2, 4, 6, and 10) complexes are analogical in profile to that of isolated PCB52 with only slightly enhanced intensity. In contrast, the corresponding SERS spectra calculated at adopted incident light are strongly enhanced, and the calculated enhancement factors are 10⁴ ~ 10⁵. Thus, the experimentally observed SERS phenomenon of PCBs supported on Ag substrates should correspond to the SERS spectra rather than the normal Raman spectra. The dominant enhancement in Raman intensities origins from the charge transfer resonance enhancement between the molecule and clusters. Copyright © 2014 John Wiley & Sons, Ltd.     

Fabrication and characterization of SERS‐active silver clusters on glassy carbon

In this article, a novel technique for the fabrication of surface enhanced Raman scattering (SERS) active silver clusters on glassy carbon (GC) has been proposed. It was found that silver clusters could be formed on a layer of positively charged poly(diallyldimethylammonium) (PDDA) anchored to a carbon surface by 4‐aminobenzoic acid when a drop containing silver nanoparticles was deposited on it. The characteristics of the obtained silver clusters have been investigated by atomic force microscopy (AFM), SERS and an SERS‐based Raman mapping technique in the form of line scanning. The AFM image shows that the silver clusters consist of several silver nanoparticles and the size of the clusters is in the range 80–100 nm. The SERS spectra of different concentrations of rhodamine 6G (R6G) on the silver clusters were obtained and compared with those from a silver colloid. The apparent enhancement factor (AEF) was estimated to be as large as 3.1 × 10⁴ relative to silver colloid, which might have resulted from the presence of ‘hot‐spots’ at the silver clusters, providing a highly localized electromagnetic field for the large enhancement of the SERS spectra of R6G. The minimum electromagnetic enhancement factor (EEF) is estimated to be 5.4 × 10⁷ by comparison with the SERS spectra of R6G on the silver clusters and on the bare GC surface. SERS‐based Raman mapping technique in the form of line scanning further illustrates the good SERS activity and reproducibility on the silver clusters. Finally, 4‐mercaptopyridine (4‐Mpy) was chosen as an analyte and the lowest detected concentration was investigated by the SERS‐active silver clusters. A concentration of 1.6 × 10⁻¹⁰ M 4‐Mpy could be detected with the SERS‐active silver clusters, showing the great potential of the technique in practical applications of microanalysis with high sensitivity. Copyright © 2006 John Wiley & Sons, Ltd.     

Effect of surface morphology on surface‐enhanced Raman scattering of 4‐aminobenzenethiol adsorbed on gold substrates

The substrate‐dependent surface‐enhanced Raman scattering (SERS) of 4‐aminobenzenethiol (4‐ABT) adsorbed on Au surfaces has been investigated. 4‐ABT is one of the very unique adsorbate molecules whose SERS spectral patterns are known to be noticeably dependent on the relative contribution of chemical enhancement mechanism vs electromagnetic enhancement mechanism. The SERS spectral patterns of 4‐ABT adsorbed on gold substrates with various surface morphology have thus been analyzed in terms of the symmetry types of the vibrational modes. Almost invisibly weak b₂ type vibrational bands were observed in the SERS spectra of the 4‐ABT adsorbed on Au colloidal sol nanoparticles or commercially available Au micro‐powders because of the weak contribution of the chemical enhancement. However, greatly enhanced b₂ vibrational bands were observed in the spectra of the 4‐ABT molecules adsorbed on the synthesized Au(Zn) sponge or the electrochemically roughened Au(ORC) foil caused by the strong contribution of the chemical enhancement mechanism. Copyright © 2008 John Wiley & Sons, Ltd.     

Raman scattering of L‐tryptophan enhanced by surface plasmon of silver nanoparticles: vibrational assignment and structural determination

Vibrational bands of L ‐tryptophan which was adsorbed on Ag nanoparticles (∼10 nm in diameter) have been investigated in the spectral range of 200–1700 cm⁻¹ using surface‐enhanced Raman scattering (SERS) spectroscopy. Compared with the normal Raman scattering (NRS) of L ‐tryptophan in either 0.5 M aqueous solution (NRS‐AS) or solid powder (NRS‐SP), the intensified signals by SERS have made the SERS investigation at a lower molecular concentration (5 × 10⁻⁴ M ) possible. Ab initio calculations at the B3LYP/6‐311G level have been carried out to predict the optimal structure and vibrational wavenumbers for the zwitterionic form of L ‐tryptophan. Facilitated with the theoretical prediction, the observed vibrational modes of L ‐tryptophan in the NRS‐AS, NRS‐SP, and SERS spectra have been analyzed. In the spectroscopic observations, there are no significant changes for the vibrational bands of the indole ring in either NRS‐AS, NRS‐SP, or SERS. In contrast, spectral intensities involving the vibrations of carboxylate and amino groups are weak in NRS‐AS and NRS‐SP, but strong in SERS. The intensity enhancement in the SERS spectrum can reach 10³–10⁴‐fold magnification. On the basis of spectroscopic analysis, the carboxylate and amino groups of L ‐tryptophan are determined to be the preferential terminal groups to attach onto the surfaces of Ag nanoparticles in the SERS measurement. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface enhanced Raman scattering from tris (bipyridine) ruthenium (II) adsorbed on silver-modified p-GaAs

Both surface enhanced Raman scattering (SERS) and surface enhanced resonant Raman scattering (SERRS) have been observed from Ru(bpy)₃²⁺ adsorbed on p-GaAs (1 0 0) after the electrodeposition of Ag particles onto the semiconductor surface. For the enhancement factor for SERS a lower limit of 10⁴ has been determined.     

Visible light response of silver 4‐aminobenzenethiolate and silver 4‐dimethylaminobenzenethiolate probed by Raman scattering spectroscopy

Silver thiolate is a layered compound with a Raman spectrum that is known to change with time, becoming the same as the surface‐enhanced Raman scattering (SERS) spectrum of the parent thiol molecule adsorbed on Ag nanoparticles. On this basis, the Raman scattering characteristics of silver 4‐aminobenzenethiolate (Ag‐4ABT) compounds were investigated to determine whether certain peaks that are identifiable in the SERS spectrum of 4‐aminobenzenethiol (4‐ABT) but absent in its normal Raman spectrum were also apparent in the Ag salt spectrum. For comparative purposes, the Raman scattering characteristics of silver 4‐dimethylaminobenzenethiolate (Ag‐4MABT) were also examined. Raman spectra acquired while spinning the sample were typified by only a₁‐type vibrational bands of Ag‐4ABT and Ag‐4MABT, whereas in the static condition, several non‐a₁‐type bands were identified. The spectral patterns acquired in the static condition were similar to the intrinsic SERS spectra of 4‐ABT or 4‐dimethylaminobenzenethiol (4‐MABT) adsorbed on pure Ag nanoparticles. Notably, the CH₃ group vibrational bands were observable for Ag‐4MABT irrespective of the sample rotation. In addition, no decrease in intensity during irradiation with a visible laser was observed for any of the bands, suggesting that no chemical conversion actually took place in either 4‐ABT or 4‐MABT. The preponderance of evidence led to the conclusion that the non‐a₁‐type bands observable in the SERS spectra must be associated with the chemical enhancement mechanism acting on the Ag nanoparticles. The chemical enhancement effect was more profound at 514.5 nm than at 632.8 nm, and was more favorable for 4‐ABT than 4‐MABT at both wavelengths. Copyright © 2012 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman spectroscopy of 4‐tert‐butylpyridine on a silver electrode

We report the observation of large surface‐enhanced Raman scattering (SERS) (10⁶) for 4‐tert‐butylpyridine molecules adsorbed on a silver electrode surface in an electrochemical cell with electrode potential set at − 0.5 V. A decrease in electrode potential to − 0.3 V was accompanied by a decrease in relative intensities of the vibrational modes. However, there were no changes in vibrational wavenumbers. Comparison of both normal solution Raman and SERS spectra shows very large enhancement of the intensities of a₁, a₂, and b₂ modes at laser excitation of 488 nm. Enhancement of the non‐totally symmetric modes indicates the presence of charge transfer as a contributor to the enhancement. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman scattering from gold‐coated germanium oxide nanowires

We utilized bulk‐synthesized nanowires (NWs) of germanium dioxide as nanoscale structures that can be coated with noble metals to allow the excitation of surface plasmons over a broad frequency range. The NWs were synthesized on substrates of silicon using gold‐catalyst‐assisted vapor–liquid–solid (VLS) growth mechanism in a simple quartz tube furnace setup. The resulting NWs have diameters of ∼100–200 nm, with lengths averaging ∼10–40 µm and randomly distributed on the substrate. The NWs are subsequently coated with thin films of gold, which provide a surface‐plasmon‐active surface. Surface‐enhanced Raman scattering (SERS) studies with near‐infrared (NIR) excitation at 785 nm show significant enhancement (average enhancement > 10⁶) with good uniformity to detect submonolayer concentrations of 4‐methylbenzenethiol (4‐MBT), trans‐1,2‐bis(4‐pyridyl)ethylene (BPE), and 1,2‐benzendithiol (1,2‐BDT) probe molecules. We also observed an intense, broad continuum in the Raman spectrum of NWs after metal coating, which tended to diminish with the analyte monolayer formation. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman scattering of 4‐aminobenzenethiol on silver: confirmation of the origin of b2‐type bands

In order to resolve the dispute on the origin of the b₂‐type bands in the surface‐enhanced Raman scattering (SERS) of 4‐aminobenzenethiol (4‐ABT), we have measured its SERS spectra under a variety of conditions, including variable temperature and rotation, electrochemistry, and pH, as well as in the presence of a reducing agent. For comparison, the SERS spectra of 4‐nitrobenzenethiol (4‐NBT) and methyl orange (MO), a prototype azo compound, were also measured. First, we found that 4‐ABT on Ag is not subjected to photoreaction, although 4‐NBT is highly photoreactive on a silver surface. In the electrochemical environment, b₂‐type bands of 4‐ABT lost their intensity at very negative potentials, but the intensity recovered immediately upon raising the potential. In addition, b₂‐type bands were observed under rotation even after lowering the potential. The disappearance and reappearance of the b₂‐type bands could also be observed by bringing the sample of 4‐ABT on Ag into contact consecutively with a borohydride solution and water. This is because the surface potential of Ag is lowered by contact with a borohydride solution. Besides, we found that not only the normal Raman but also the SERS spectral features of 4‐ABT are hardly affected by pH variation, while the spectral features of MO are greatly affected, especially in the region of the NN stretching vibration, suggesting that the possibility of a photoconversion of 4‐ABT to an azo compound is low. Altogether, the b₂‐type bands were attributed to 4‐ABT, appearing in conjunction with the chemical enhancement mechanism in SERS. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman scattering sensing on black silicon

Reactive ion etching was used to fabricate black‐Si over the entire surface area of 4‐inch Si wafers. After 20 min of the plasma treatment, surface reflection well below 2% was achieved over the 300–1000 nm spectral range. The spikes of the black‐Si substrates were coated by gold, resulting in an island film for surface‐enhanced Raman scattering (SERS) sensing. A detection limit of 1 × 10^?6 M (at count rate > 10² s^?1 . mW^?1) was achieved for rhodamine 6G in aqueous solution when drop cast onto a ～ 100‐nm‐thick Au coating. The sensitivity increases for thicker coatings. A mixed mobile‐on‐immobile platform for SERS sensing is introduced by using dog‐bone Au nanoparticles on the Au/black‐Si substrate. The SERS intensity shows a non‐linear dependence on the solid angle (numerical aperture of excitation/collection optics) for a thick gold coating that exhibits a 10 times higher enhancement. This shows promise for augmented sensitivity in SERS applications.     

Surface‐enhanced Raman scattering‐based approach for DNA detection at low concentrations via polyvinyl alcohol‐protected silver grasslike patterns

A simple method is demonstrated to detect DNA at low concentrations on the basis of surface‐enhanced Raman scattering (SERS) via polyvinyl alcohol‐protected silver grasslike patterns (PVA‐Ag GPs) grown on the surface of the common Al substrate. By the SERS measurements of sodium citrate and thymine, the PVA‐Ag GPs are shown to be an excellent SERS substrate with good activity, stability and reproducibility. With the use of the tested molecule of thymine, the enhancement factor of the PVA‐Ag GPs is up to ~1.4 × 10⁸. The PVA‐Ag GPs are also shown to be an excellent SERS substrate with good biocompatibility for DNA detection, and the detection limit is down to ~10⁻⁵ mg/g. Meanwhile, the assignations of the Raman bands and the adsorption behaviors of the DNA molecules are also analyzed. In this work, the geometry optimization and the wavenumber analysis of adenine–Ag and guanine–Ag complexes for the ground states are performed using density functional theory, B3LYP functional and the LanL2DZ basis set. The transition energies and the oscillator strengths of adenine–Ag and guanine–Ag for the lowest six singlet excited states were calculated by using the time‐dependent density functional theory method with the same functional and basis set. The results show that the charge transfer in the adenine–Ag and guanine–Ag complexes should be the chemical factor for the SERS of the DNA molecules. Lastly, this method may be employed in large‐scale preparation of substrates that have been widely applied in the Raman analysis of DNA because the fabrication process is simple and inexpensive. Copyright © 2011 John Wiley & Sons, Ltd.     

Silver‐decorated carbon nanotube networks as SERS substrates

We report on investigations upon a surface‐enhanced Raman scattering (SERS) substrate produced from a two‐dimensional single‐walled carbon nanotube (SWNT) network decorated with Ag nanoparticles. Using the strong and unique Raman spectrum of SWNTs as a reference, the SWNT/Ag nanostructure can be considered to provide two regions: one with an ultrasensitive SERS response for single‐molecule SERS (SMSERS) study; and another with uniform SERS enhancement over an area of several square millimeters for general SERS measurements. We report the appearance of an anomalous Raman feature at around 2180 cm⁻¹ in the high‐sensitivity region which exhibits the characteristics of SMSERS. The SERS performance of the uniform area was characterized using pyridine vapor adsorbed onto the substrate. The presence of the SWNT/Ag nanostructure enhanced the Raman intensity by over seven orders of magnitude, a factor comparable to or exceeding that obtained on SERS substrates reported by other groups. The results indicate great potential to produce highly sensitive, uniform SERS substrates via further fine‐tuning of the nanostructure. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface enhanced Raman spectroscopic (SERS) behavior of substituted propenoic acids used in heterogeneous catalytic asymmetric hydrogenation

The strength and geometry of adsorption of substituted propenoic acids on silver surface were studied by means of surface enhanced Raman spectroscopy (SERS) using silver sol. Based on their SERS behavior, two classes of phenylpropenoic acids studied were distinguished. The first class of propenoic acids (atropic acid, (E)‐2,3‐diphenylpropenoic acid, (E)‐2‐(2‐methoxyphenyl)‐3‐phenylpropenoic acid, (E)‐2,3‐di‐(4‐methoxyphenyl)phenylpropenoic acid and (E)‐2‐(2‐methoxyphenyl)‐3‐(4‐fluorophenyl)propenoic acid) has shown strong charge transfer (CT) effect. We suggest bidentate carboxyl bonded species based on the SERS enhanced bands of νCOO⁻ around 1394 cm⁻¹ and νC―C of the ―C―COO⁻ moiety at 951 cm⁻¹. In these series the plane of the α‐phenyl group (γCH out‐of‐plane vibrations at 850–700 cm⁻¹) is almost parallel to the silver surface, while the β‐phenyl group is in tilted position depending on the type and the position of substituent(s) showing strong SERS enhanced bands of νCC + βCH (in‐plane mode) at 1075 cm⁻¹, νCC (ring breathing mode, in‐plane) at 1000 cm⁻¹ and γCCC (out‐of‐plane mode) around 401 cm⁻¹. The other class of propenoic acids (cinnamic acid, (E)‐2‐phenyl‐3‐(4‐methoxyphenyl)propenoic acid) has shown weak electromagnetic (EM) enhancement (CC bands is enhanced in cinnamic acid). In this case no significant carboxyl enhancement was observed, so we suggest that adsorbed species lie parallel to the surface. The two types of adsorption can be related to the dissociation ability of the carboxylic group. In the first case the carboxylic H dissociates, while in the second case it does not, as indicated also by the characteristic νCO band at 1686 cm⁻¹ in the FT‐Raman spectra of methanolic solutions. Copyright © 2015 John Wiley & Sons, Ltd.     

Design of plasmonic bowtie nanoring array with high sensitivity and reproducibility for surface‐enhanced Raman scattering spectroscopy

A metallic bowtie nanoring array is designed to gain high sensitive and reproducible substrate for surface‐enhanced Raman scattering (SERS) spectroscopy. The localized surface plasmon resonance (LSPR), the electric field enhancement factors (EFs) and the electric field distribution of the bowtie and bowtie nanoring array are numerically investigated by means of the finite‐difference time domain (FDTD) method. After the optimization of the particle size and the array period, the maximum electromagnetic field EF approaches 153, and the corresponding SERS electromagnetic enhancement factor (EMEF) reaches 5.4 × 10⁸. This highly sensitive and reproducible substrate can be a good candidate for SERS applications. Copyright © 2011 John Wiley & Sons, Ltd.     

A hybrid substrate for surface‐enhanced Raman scattering spectroscopy: coupling metal nanoparticles to strong localised fields on a micro‐structured surface

Electromagnetic coupling between localised plasmons on metal nanoparticles and the strong localised fields on a micro‐structured surface is demonstrated as a means to increase the enhancement factor in surface‐enhanced Raman scattering (SERS) spectroscopy. Au nanoparticles of diameter 20 nm were deposited on a micro‐structured Au surface consisting of a periodic array of square‐based pyramidal pits (Klarite). The spectra of 4‐aminothiophenol (4‐ATP) were compared before and after deposition of Au nanoparticles on the micro‐structured surface. The addition of Au nanoparticles is shown to provide significantly higher signal intensities, with improvements of the order of ∼10³ per molecule compared with spectra obtained from the micro‐structured substrate alone. This hybrid approach offers promise for combining nanoparticles with micro‐ and nano‐structured surfaces in order to design SERS substrates with higher sensitivities. Copyright © 2011 John Wiley & Sons, Ltd.     

Raman spectroscopy of dipyrrins: nonresonant,resonant and surface‐enhanced cross‐sections and enhancement factors

Detailed studies of the mechanism of surface‐enhanced (resonance) Raman spectroscopy (SE(R)RS), and its applications, place a number of demands on the properties of SERS scatterers. With large Raman cross‐sections, versatile synthetic chemistry and complete lack of fluorescence, free dipyrrins meet these demands but the Raman and SE(R)RS spectroscopy of free dipyrrins is largely unknown. The first study of the Raman spectroscopy of free dipyrrins is therefore presented in this work. The nonresonant Raman, resonant Raman and surface‐enhanced Raman spectra of a typical meso aryl‐substituted‐dipyrrin are reported. Absolute differential cross‐sections are obtained for excitation wavelengths in the near infrared and visible region, in solution phase and for dipyrrin adsorbed on the surface of silver nanoparticles. Raman enhancement factors for SERRS and resonance Raman are calculated from the observed differential cross‐sections. The magnitudes of the resonantly enhanced cross‐sections are similar to those recently reported for strong SERS dyes such as Rhodamine 6G and Crystal Violet. Free dipyrrins offer the advantages of existing SERS dyes but without the drawback of strong fluorescence. Free dipyrrins should therefore find applications in all areas of Raman spectroscopy including fundamental studies of the mechanisms of SERS and bioanalytical and environmental applications. Copyright © 2011 John Wiley & Sons, Ltd.     

A three‐dimensional surface‐enhanced Raman scattering substrate: Au nanoparticle supramolecular self‐assembly in anodic aluminum oxide template

A three‐dimensional surface‐enhanced Raman scattering (SERS) substrate via the self‐assembly of properly sized Au nanoparticles in anodic aluminum oxide templates was designed and prepared. Au nanoparticles first underwent hydrophobic surface modification. Then, the hydrophobic Au nanoparticles self‐assembled, aggregated and formed many hot spots in the anodic aluminum oxide templates through a supramolecular interaction. We chose thiophenol as a probe molecule to evaluate the SERS enhancement ability of this three‐dimensional substrate. The enhancement factor was calculated to be 4.6 × 10⁶ under the radiation of a 785‐nm laser. By further comparing SERS signals from different points on the same substrate, we confirmed that this substrate possessed good reproducibility and could be applied for SERS detection. Copyright © 2011 John Wiley & Sons, Ltd.     

Comparison of SERS effectiveness of copper substrates prepared by different methods: what are the values of enhancement factors?

Surface‐enhanced Raman scattering (SERS) spectroscopy is an analytical method for the detection of low amounts of analytes adsorbed on an appropriate coinage metal (Au, Ag, Cu) surface. Generally, the values of the enhancement factor are the highest on silver, lower on gold and relatively very low on copper. In this study, we have focused on the estimation of the enhancement factors of copper surface/substrates formed by different preparation procedures. The SERS activity of large electrochemically prepared substrates and colloidal systems is compared. The surface morphology of the large substrates was studied using scanning electron microscopy and atomic force microscopy. The size distribution of colloidal nanoparticles was monitored by dynamic light scattering. The values of enhancement factor are in both cases more than 10⁵ for the FT‐SERS spectra, demonstrating the fundamental role of nanostructured copper as a substrate material at the excitation wavelength (1064 nm) used. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman spectroscopy of DNA from leaves of in vitro grown apple plants

Ultrasensitive Raman measurements of nucleic acids are possible by exploiting the effect of surface‐enhanced Raman scattering (SERS). In this work, the vibrational spectra of eight genomic DNAs from in vitro grown apple leaf tissues (Malus domestica Borkh., Fam Rosaceae, cvs. Florina, Idared, Rebra, Goldrush, Romus 3, Romus 4 and the rootstocks M9 and M26) were analyzed using surface‐enhanced Raman spectroscopy, in the wavenumber range 200–1800 cm⁻¹. SERS signatures, spectroscopic band assignments and structural interpretations of these plant genomic DNAs are reported. Strong dependences of the SERS spectra on genomic DNA amount in the measured sample volume and on time were observed. Similarities of the SERS signals of DNAs from Rebra and Romus 3 leaves were detected. To our knowledge, this is the first SERS study on genomic DNA from leaf tissues. The present work provides a basis for future use of surface‐enhanced Raman spectroscopy to analyze specific plant DNA–ligand interactions or DNA structural changes induced by plants' stress conditions associated with their natural environment. Besides, this study will generate information that is valuable in the development of low‐level plant DNA‐based analytical sensors. Copyright © 2010 John Wiley & Sons, Ltd.