Solid‐state modification of polypropylene (PP): grafting of styrene on atactic PP

Grafting of unsaturated vinyl monomers onto polypropylene (PP) is a convenient route to develop new polymeric materials with synergistic properties. Particular attention must be paid to the formation of graft copolymer relative to the formation of homopolymer, since the final properties are dependent both on the dispersion of the new polymer into the iPP matrix, which is controlled by the degree of grafting, as well as on the chemical nature of the in‐situ formed polymer chains. In the present work the grafting reaction of styrene on atactic PP (aPP), considered as good model system for the more studied solid‐state modification of isotactic PP (iPP), has been investigated in the presence of two different radical initiators in order to get a first insight into the grafting reactions onto PP. Several grafting reactions were carried out by changing the chemical compositions of the starting polymerization mixture, whose homogeneity was accurately investigated by Raman spectroscopy. Infrared‐spectroscopy (FT‐IR) was used for qualitative and quantitative characterization of the reaction product. A quantitative separation procedure, based on the concept of selective solvent extraction, has been established which enables the determination of the grafting efficiency (Φ) as well as the exact chemical composition of the final product. Finally, all products were characterized by means of Differential Scanning Calorimetry (DSC) in order to study their thermal behaviour.     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004     

TIME-DEPENDENT MORPHOLOGY OF POLYETHYLENE-POLYPROPYLENE BLENDS

The effect of time-temperature treatment on morphology of polyethylene-polypropylene (PE-PP) blends wasstudied to establish a relationship between thermal history, morphology and mechanical properties. Polypropylene (PP)homopolymers were used to blend with various polyethylenes (PE), including high density polyethylene (HDPE), lowdensity polyethylene (LDPE), linear low density polyethylene (LLDPE), and very and ultra low density polyethylene(VLDPE and ULDPE). The majority of the blends were prepared at a ratio of PE:PP = 80:20, while blends of PP and LLDPEwere prepared at various compositions. Thermal treatment was carried out at temperatures between the crystallizationtemperatures of PP and PEs to allow PP to crystallize first from the blends. On cooling further, PE crystallized too. A verydiffuse PP spherulite morphology in the PE matrix was formed in some partially miscible blends when PP was less than 20%by mass. Droplet-matrix structures were developed in other blends with either PP or PE as dispersed domains in a continuousmatrix, depending on the composition ratio. The scanning electron microscopy (SEM) images displayed a fibrillar structureof PP spherulite in the LLDPE-PP (80:20) and large droplets of PP in the HDPE-PP (80:20) blend, providing larger surfacearea and better bonding in the LLDPE-PP (80:20) blends. This explains why the blends with diffuse spherulite morphologyshowed greater improvement in tensile properties than droplet-matrix morphology blends after time-temperature treatment.     

Enhanced mechanics in injection molded isotactic polypropylene/polypropylene random copolymer blends via introducing network-like crystal structure

The crystallization behavior, rheological behavior, mechanical properties and microstructures of injection molded isotactic polypropylene(i PP), polypropylene random copolymer(co-PP) and i PP/co-PP blends were investigated. Differential scanning calorimetry(DSC) and dynamic rheological analysis illustrated that i PP and co-PP were compatible in the blends and co-PP uniformly dispersed in the i PP phase. Polarizing optical microscope(POM) was adopted to observe the crystal size and morphology evolution. The results of mechanical properties and scanning electron microscopy(SEM) indicated that the crystal size of i PP in i PP/co-PP blends(10 wt% co-PP + 90 wt% i PP and 30 wt% co-PP + 70 wt% i PP) radically decreased after the incorporation of co-PP. During crystallization, the molecular chain segments of co-PP could penetrate i PP spherulites and form a network-like crystalline structure. The network-like crystal structure could effectively transmit stress and consume more energy to overcome intermolecular forces to resist stretching. In this way, the strength would improve to a certain degree. The impact fracture mechanism of i PP/co-PP blends is quasi ductile fracture by multiple crazes. Our work discovered that the blends containing 10 wt% and 30 wt% of co-PP exhibited prominent toughness and reinforcement.     

显微镜图像分析研究聚丙烯/尼龙1010共混物相结构及其性能

用扫描电子显微镜图像分析研究了聚丙烯/聚酰胺1010共混物及其部分相容体系的相形态结构,计算了表征相结构和尺寸的结构参数,如分散相的平均直径、平均弦长和分散相的质心相关距等.并分别讨论了聚丙烯/聚酰胺1010共混物及其部分相容体系的相形态以及其结构参数与共混物组成的关系.测定了聚合物及其共混物体系的力学性能,讨论了共混物组成与力学性能的关系.聚丙烯/聚酰胺1010共混物的拉伸模量与组成的关系较为复杂,但其部分相容体系的拉伸模量与组成呈线性关系.聚丙烯/聚酰胺1010及其共混物体系的屈服强度与共混物组成均呈线性关系.表征相结构的两相平均弦长比(l-1/-l2)与组成以及共混物体系力学性能与组成的关系,二者相似.同时讨论了体系力学性能随相尺寸等的变化规律.     

Electrical properties and conductive mechanisms of immiscible polypropylene/Novolac blends filled with carbon black

Carbon black (CB)-filled immisicible thermoplastic/thermosetting polymer blends consisting of polypropylene (PP) and Novolac resin were reported in this paper. The PP/Novolac/CB blends with varied compositions and different processing sequences were prepared by melt-mixing method. The CB distribution, conductive mechanism and the relationship between morphology and electrical properties of the PP/Novolac/CB blends were investigated. Scanning electron microscopy (SEM), optical microscopy and extraction experiment results showed that in PP/Novolac blends CB particles preferentially localized in the Novolac phase, indicating CB has a good affinity with Novolac resin. The incorporation of CB changed the spherical particles of the dispersed Novolac phase into elongated structure. With increasing Novolac content, the elongation deformation of Novolac phase became more obvious and eventually the blends developed into co-continuous structure, which form double percolation and decrease the percolation threshold. When CB was initially blended with PP and followed by the addition of Novolac resin, the partial migration of CB from PP to the Novolac phase was possibly occurred. The addition of Novolac to PP evidently increases the storage modulus G′, loss modulus G″ and complex viscosity η^∗. The addition of CB to PP/Novolac blends further increase η^∗, and it increases with increasing CB loading, which was related to the change of composite morphology.     

Fracture studies of polypropylene/nanoclay composite. Part I: Effect of loading rates on essential work of fracture

Polypropylene (PP)/Montmorillonite (MMT) nanoclay based composite was prepared by melt compounding with maleic anhydride grafted polypropylene (MA-g-PP) as a compatibilizer in a twin-screw extruder, and the test specimens were injection molded. Mechanical properties such as tensile modulus, flexural modulus, yield strength and maximum percent strains were measured for pure PP and PP based nanocomposite to establish the effect of clay platelet reinforcement. The fracture properties were measured by using the essential work of fracture (EWF) method. PP/clay nanocomposite shows 25% improvement in specific EWF compared to pure PP. The variation of EWF parameters with loading rate is discussed, whilst the mechanisms of fracture are considered in a subsequent paper.     

AGSE: A Novel Grape Seed Extract Enriched for PP2A Activating Flavonoids That Combats Oxidative Stress and Promotes Skin Health

Environmental stimuli attack the skin daily resulting in the generation of reactive oxygen species (ROS) and inflammation. One pathway that regulates oxidative stress in skin involves Protein Phosphatase 2A (PP2A), a phosphatase which has been previously linked to Alzheimer’s Disease and aging. Oxidative stress decreases PP2A methylation in normal human dermal fibroblasts (NHDFs). Thus, we hypothesize agents that increase PP2A methylation and activity will promote skin health and combat aging. To discover novel inhibitors of PP2A demethylation activity, we screened a library of 32 natural botanical extracts. We discovered Grape Seed Extract (GSE), which has previously been reported to have several benefits for skin, to be the most potent PP2A demethylating extract. Via several fractionation and extraction steps we developed a novel grape seed extract called Activated Grape Seed Extract (AGSE), which is enriched for PP2A activating flavonoids that increase potency in preventing PP2A demethylation when compared to commercial GSE. We then determined that 1% AGSE and 1% commercial GSE exhibit distinct gene expression profiles when topically applied to a 3D human skin model. To begin to characterize AGSE’s activity, we investigated its antioxidant potential and demonstrate it reduces ROS levels in NHDFs and cell-free assays equal to or better than Vitamin C and E. Moreover, AGSE shows anti-inflammatory properties, dose-dependently inhibiting UVA, UVB and chemical-induced inflammation. These results demonstrate AGSE is a novel, multi-functional extract that modulates methylation levels of PP2A and supports the hypothesis of PP2A as a master regulator for oxidative stress signaling and aging in skin.     

Morphology, crystallization behavior and properties of impact-modified polypropylene copolymer with or without sodium benzoate as a nucleating agent

 The morphology, crystallization behavior, and properties of an impact-modified polypropylene (PP) copolymer with or without sodium benzoate were investigated. The contents of ethylene–propylene rubber (EPR) in the reactor-made PP copolymer is about 15 wt%. For comparison, blends of PP and EPR containing the same EPR composition were prepared by melt-mixing. Morphological studies by scanning probe microscopy indicated that the impact-modified copolymer consists of three different phases, i.e., polyethylene, PP, and EPR phases, which is considerably different from the morphology of the conventional PP/EPR blend of the corresponding composition. The impact-modified PP copolymer exhibited a higher crystallization rate in terms of the lower crystallization half-time and thus higher thermal and mechanical properties, such as impact strength and hardness, than the PP/EPR blend did. The addition of sodium benzoate as a nucleating agent to the copolymer increased the crystallization rate and the mechanical properties. Received: 4 June 2001 Accepted: 31 October 2001     

Characterization of PP/HDPE blend-based nanocomposites using different maleated polyolefins as compatibilizers

Nanocomposites based on a polypropylene (PP)/high density polyethylene (HDPE) blend were prepared using an organo-montmorillonite (15A) as a nano-filler and two maleated polyolefins (PE-MA and PP-MA) as compatibilizers. The phase morphology and typical physical properties of the prepared samples were examined. The nano-filler 15A was intercalated and/or partially exfoliated in the blend when PE-MA or PP-MA was present. The PE-MA facilitated the dispersibility of 15A to a better degree. The nano-filler 15A accelerated the crystallization of PP in the blends, whereas it hardly influenced the crystallization of HDPE. Moreover, at a slow cooling rate (i.e., 1 °C/min) the PP-MA induced a higher crystallization temperature for PP in the composite, while PE-MA impeded PP crystallization. On the other hand, the crystallization of HDPE in the composite was only slightly influenced by the presence of PE-MA or PP-MA. The thermal stability of PP/HDPE blend was enhanced after the addition of 15A regardless of the inclusion or not of PE-MA or PP-MA. The enhancement was more evident when the samples were scanned under an air environment than a N2 environment. The stiffness of PP/HDPE blend increased marginally after adding 15A and was slightly altered with the further inclusion of PP-MA. The presence of PE-MA in the composite caused a slight decline in the stiffness. The impact strength of PP/HDPE blend declined after the formation of nanocomposites, especially for the sample incorporating PP-MA.     

Morphology and mechanical behavior of isotactic polypropylene with different stereo‐defect distribution in injection molding

Large amount of work has been published on the isotacticity–properties relationship of isotactic polypropylene (iPP). However, the stereo‐defect distribution dependence of morphology and mechanical properties of iPP injection molding samples is still not clear. In this study, two different isotactic polypropylene (iPP) resins (PP‐A and PP‐B) with similar average isotacticity but different stereo‐defect distribution were selected to investigate the morphology evolution and mechanical properties (tensile and notching) of their injection molding samples using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), 2D wide angle X‐ray diffraction (2D‐WAXD), and scanning electron microscope (SEM). The results of DMA showed that the molecular movement ability of PP‐A (with less uniform distribution of stereo‐defect) was stronger than that of PP‐B, meanwhile the analysis of DSC and SEM suggested that after injection molding, smaller spherullites, and crystals with higher perfection had formed in the specimens of PP‐A. The resulting of tensile properties of PP‐A were found to be better than that of PP‐B. The results of morphology evolution by SEM observation and 2D‐WAXD showed that PP‐A is more likely to occur interspherulite deformation and can disperse the tensile stress more efficiently, and therefore, its crystal structure can withstand a greater force when tensile stress is applied. On the other hand, PP‐B has larger spherulites and boundaries, and low perfection of lamellaes, and the intraspherulte deformation tend to take place. It is easier for the crystal of PP‐B to be broken up and reoriented along the tensile direction. Copyright © 2014 John Wiley & Sons, Ltd.     

Recent advances in sample preparation techniques for effective bioanalytical methods

This paper reviews the recent developments in bioanalysis sample preparation techniques and gives an update on basic principles, theory, applications and possibilities for automation, and a comparative discussion on the advantages and limitation of each technique. Conventional liquid-liquid extraction (LLE), protein precipitation (PP) and solid-phase extraction (SPE) techniques are now been considered as methods of the past. The last decade has witnessed a rapid development of novel sample preparation techniques in bioanalysis. Developments in SPE techniques such as selective sorbents and in the overall approach to SPE, such as hybrid SPE and molecularly imprinted polymer SPE, have been addressed. Considerable literature has been published in the area of solid-phase micro-extraction and its different versions, e.g. stir bar sorptive extraction, and their application in the development of selective and sensitive bioanalytical methods. Techniques such as dispersive solid-phase extraction, disposable pipette extraction and micro-extraction by packed sorbent offer a variety of extraction phases and provide unique advantages to bioanalytical methods. On-line SPE utilizing column-switching techniques is rapidly gaining acceptance in bioanalytical applications. PP sample preparation techniques such as PP filter plates/tubes offer many advantages like removal of phospholipids and proteins in plasma/serum. Newer approaches to conventional LLE techniques (salting-out LLE) are also covered in this review article.     

The effects of reprocessing cycles on the structure and properties of isotactic polypropylene/cloisite 15A nanocomposites

The effects of reprocessing cycles on the structure and properties of isotactic polypropylene (PP)/Cloisite 15A (OMMT) (5 wt. %) nanocomposites was studied in presence of maleic anhydride-grafted-polypropylene (PP-g-MA) (20 wt. %) used as the compatibiliser to improve the clay dispersion in the polymer matrix. The various nanocomposite samples were prepared by direct melt intercalation in an internal mixer, and further they were subjected to 4 reprocessing cycles. For comparative purposes, the neat PP was also processed under the same conditions. The nanocomposite structure and the clay dispersion have been characterized by wide angle X-ray scattering (WAXS), transmission electron microscopy (TEM) and rheological measurements. Other characterization techniques such as Fourier transform infrared spectroscopy (FT-IR), tensile measurements, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) have also been used to evaluate the property changes induced by reprocessing. The study showed through XRD patterns that the repetitive reprocessing cycles modified the initial morphology of PP/OMMT nanocomposites by improving the formation of intercalated structure, especially after the fourth cycle. Further, the addition of PP-g-MA promoted the development of intercalated/exfoliated silicate layers in the PP matrix after the second cycle. These results are in agreement with TEM observations indicating an improved silicate dispersion in the polymer matrix with reprocessing cycles displaying a morphology with both intercalated/exfoliated structures. The initial storage modulus (G′) of the nanocomposites, which was highly improved in presence of PP-g-MA seems to be less affected by reprocessing cycles at very low frequencies exhibiting a quasi-plateau compared to pristine PP/OMMT and PP. In contrast, the complex viscosity was found to decrease for the whole samples indicating that the main effect of reprocessing was a decrease in the molecular weight. Moreover, the thermal and mechanical properties of the nanocomposites were significantly reduced after the first cycle; nevertheless they remained almost unchanged during recycling. No change in the chemical structure was observed in the FT-IR spectra for both the nanocomposites and neat PP samples after 4 cycles.     

共混过程中EPDM/PP共混热塑弹性体的结构、形态和性能的变化

用SEM,TEM,DSC,WAXD和有效网链密度(v_e)测定,研究了共混时间长短和返炼对EPDM/PP共混物结构和性能的影响。两相分散随共混时间和返炼而更趋均匀。随共混时间,PP结晶度(x_c)先行降低然后升高,抗张强度正相反,v_e则降低x_e和v_e返炼后总是较一次共混降低。影响强度的因素主要是两相分散均匀和两相界面的相互渗透。     

Catalytic action of phospho-tungstic acid in the synthesis of melamine salts of pentaerythritol phosphate and their synergistic effects in flame retarded polypropylene

A solid acid, phospho-tungstic acid (PTA), has been used to catalyze the pentaerythritol-melamine phosphate (PER-MP) reaction to synthesize intumescent flame retardant, melamine salt of pentaerythritol phosphate (MPP) used in flame retardant polypropylene (PP). This novel and environmentally friendly synthesis technology well solves the problems of conventional preparation methods. PTA plays a double-role: on one hand, it remarkably enhances the conversion of the above reaction and decreases the reaction temperature; on the other hand, it acts as an effective synergist with MPP and greatly improves the flame retardancy; accordingly, no additional process is needed to remove PTA after the reaction, and the products of the catalyzed reaction were directly incorporated with PP to prepare high-performance flame retardant materials. The catalytic and synergistic effects of PTA, as well as the flame retardancy and mechanical properties of the corresponding flame retardant PP were investigated.     

In situ surface-enhanced IR absorption spectroscopy on CO adducts of iron protoporphyrin IX self-assembled on a Au electrode

The surface coordination chemistry of carbon monoxide with the reduced form (Fe(II)PP) of iron(III) protoporphyrin IX (Fe(III)PP) monolayer self-assembled on a Au electrode in 0.1 M HClO4 was studied for the first time by using in situ ATR-surface-enhanced infrared absorption spectroscopy (ATR-SEIRAS). Both mono- and biscarbonyl adducts [simplified as Fe(II)(CO)PP and Fe(II)(CO)2PP, respectively] were detected, depending on the history of potential control. Initially, the Fe(II)(CO)PP predominates, and the intermediate transition potential for the conversion of Fe(II)(CO)PP to Fe(III)PP and CO was spectrally determined to be ca. 0.09 V (vs SCE). The ratio of Fe(II)(CO)2PP and Fe(II)(CO)PP increases after a potential excursion to a sufficiently positive value. Fe(II)(CO)2PP is much more stable against its electro-oxidation to Fe(III)PP than its counterpart Fe(II)(CO)PP with increasing potential. The observed change of coordination properties may be ascribed to an irreversible structural reorganization of the FePP adlayer caused by the potential excursion.     

Effect of Phosphorus-Nitrogen Intumescent Flame Retardant on Structure and Properties of Poly(propylene)

Summary : Phosphorus-nitrogen intumescent product (R₂₀₀₀) was filled into polypropylene (PP) as a flame retardant. The neat PP and flame-retarded PP blends were studied for their structural and mechanical properties after verification of the flame retardancy character of blends. In this paper, the influence of incorporation of different amount (5%, 10%, 15%, 20%, and 25%) of R₂₀₀₀ was studied. The flame retardancy is evaluated by limiting oxygen index (LOI) value, which is enhanced from 17.5 for pure PP to 22.7 for the blend comprising 15% intumescent product, phosphorus-nitrogen based (R₂₀₀₀). The thermal degradation behaviour of the PP/R₂₀₀₀ blends was investigated using thermogravimetric analysis (TGA) under nitrogen (N₂) and oxygen (O₂) atmospheres. The influence of the R₂₀₀₀ on the PP crystallization was examined by X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Further, the mechanical properties of the materials were studied by dynamic mechanical analysis (DMA). The incorporation of the flame retardant had no effect on the crystallization of the neat polymer and the mechanical properties of the materials remained unaffected.     

无机刚性粒子增韧聚丙烯的影响因素

简要介绍了无机刚性粒子对聚丙烯(PP)的增韧机理,并着重介绍了利用无机刚性粒子增韧PP时,PP基体、无机刚性粒子的性质及用量、无机刚性粒子在PP基体中的分散情况、无机刚性粒子与PP基体间的界面相互作用等因素对增韧效果的影响。     

Polypropylene-polysilsesquioxane blends

This paper deals with the preparation of PP/polysilsesquioxane blends and their study to investigate silsesquioxane dispersion, mechanical properties, thermal stability and combustion properties by means of a number of techniques, such as SEM, XRD, Rheology, TGA, DSC, Cone Calorimeter tests and LOI.Polysilsesquioxane with different organic groups (methyl, vinyl or phenyl) were used; both dispersion and final properties were found to be dependent on the silsesquioxane organic fraction type.The PP/polysilsesquioxane blends showed an increased thermoxidative stability and combustion resistance, in terms of lower rate of heat release.Higher mechanical performances were also achieved with PP/vinyl polysilsesquioxane, with higher elastic modulus as well as higher elongation at break.