Elucidating surface properties of dry-etched ZnO using H2/CH4 and H2/CH4/Ar plasma

This paper reports a study of reactive ion etching (RIE) of n-ZnO in H₂/CH₄ and H₂/CH₄/Ar gas mixtures. Variables in the experiment were gas flow ratios, radio-frequency (rf) plasma power, and total pressure. Structural and electrical parameters of the etched surfaces and films were determined. Both the highest surface roughness and highest etching rate of ZnO films were obtained with a maximum rf power of 300 W, but at different gas flow ratios and working pressures. These results were expected because increasing the rf power increased the bond-breaking efficiency of ZnO. The highest degree of surface roughness was a result of pure physical etching by H₂ gas without mixed CH₄ gas. The highest etching rate was obtained from physical etching of H₂/Ar species associated with chemical reaction of CH₄ species. Additionally, the H₂/CH₄/Ar plasma treatment drastically decreased the specific contact and sheet resistance of the ZnO films. These results indicated that etching the ZnO film had roughened the surface and reduced its resistivity to ohmic contact, supporting the application of a roughened transparent contact layer (TCL) in light-emitting diodes (LEDs).     

Temperature-dependent photoluminescence spectra of Er-Tm-codoped Al2O3 thin film

Er-Tm-codoped Al₂O₃ thin films with different Tm to Er concentration ratios were synthesized by cosputtering from separated Er, Tm, Si, and Al₂O₃ targets. The temperature dependence of photoluminescence (PL) spectra was studied. A flat and broad emission band was achieved in the 1.4-1.7 μm and the observed 1470, 1533 and 1800 nm emission bands were attributed to the transitions of Tm³⁺: ³H₄ → ³F₄, Er³⁺: ⁴I_13/2 → ⁴I_15/2 and Tm³⁺: ³F₄ → ³H₆, respectively. The temperature dependence is rather complicated. With increasing measuring temperature, the peak intensity related to Er³⁺ ions increases by a factor of five, while the Tm³⁺ PL intensity at 1800 nm decreases by one order of magnitude. This phenomenon is attributed to a complicated energy transfer (ET) processes involving both Er³⁺ and Tm³⁺ and increase of phonon-assisted ET rate with temperature as well. It should be helpful to fully understand ET processes between Er and Tm and achieve flat and broad emission band at different operating temperatures.     

Effect of H2 and O2 plasma etching treatment on the surface of diamond-like carbon thin film

In this study, we investigated the surface properties of diamond-like carbon (DLC) films for biomedical applications through plasma etching treatment using oxygen (O₂) and hydrogen (H₂) gas. The synthesis and post-plasma etching treatment of DLC films were carried out by 13.56 MHz RF plasma enhanced chemical vapor deposition (PECVD) system. In order to characterize the surface of DLC films, they were etched to a thickness of approximately 100 nm and were compared with an as-deposited DLC film. We obtained the optimum condition through power variation, at which the etching rate by H₂ and O₂ was 30 and 80 nm/min, respectively. The structural and chemical properties of these thin films after the plasma etching treatment were evaluated by Raman and Fourier transform infrared (FT-IR) spectroscopy. In the case of as-deposited and H₂ plasma etching-treated DLC film, the contact angle was 86.4° and 83.7°, respectively, whereas it was reduced to 35.5° in the etching-treated DLC film in O₂ plasma. The surface roughness of plasma etching-treated DLC with H₂ or O₂ was maintained smooth at 0.1 nm. These results indicated that the surface of the etching-treated DLC film in O₂ plasma was hydrophilic as well as smooth.     

Low energy Ar-ion bombardment effects on the CeO2 surface

The structure and electronic properties of epitaxial grown CeO₂(1 1 1) thin films before and after Ar⁺ bombardment have been comprehensively studied with synchrotron radiation photoemission spectroscopy (SRPES). Ar⁺ bombardment of the surface causes a new emission appearing at 1.6 eV above the Fermi edge which is related to the localized Ce 4f¹ orbital in the reduced oxidation state Ce³⁺. Under the condition of the energy of Ar ions being 1 keV and a constant current density of 0.5 μA/cm², the intensity of the reduced state Ce³⁺ increases with increasing time of sputtering and reaches a constant value after 15 min sputtering, which corresponds to the surface being exposed to 2.8 × 10¹⁵ ions/cm². The reduction of CeO₂ is attributed to a preferential sputtering of oxygen from the surface. As a result, Ar⁺ bombardment leads to a gradual buildup of an, approximately 0.69 nm thick, sputtering altered layer. Our studies have demonstrated that Ar⁺ bombardment is an effective method for reducing CeO₂ to CeO_2−x and the degree of the reduction is related to the energy and amount of Ar ions been exposed to the CeO₂ surface.     

Effect of Ar in the source gas on the microstructure and optoelectronic properties of microcrystalline silicon films deposited by plasma-enhanced CVD

Hydrogenated microcrystalline silicon films have been prepared by plasma-enhanced chemical vapor deposition technique using silane diluted in H₂ or H₂ + Ar. The microstructures for silicon films have been evaluated by Raman scattering spectroscopy, X-ray diffraction and Fourier-transform infrared spectroscopy. Optical characterization has been done by UV-vis spectroscopy. It is found that the addition of Ar in diluent gases efficiently improves the deposition rate and crystallinity due to an enhanced dissociation of the source gas and the energy of deexcitation of Ar* released within the growth zone. Meanwhile, the enhanced crystallinity and the reducing of hydrogen ion bombardment with increasing Ar dilution lead to the polymerization and also a bad passivation of the hydrogen which cause the widening of the optical gap and increase of defect states in the μc-Si films. The absorption coefficient and dark conductivity are found to decrease basically with increasing Ar dilution corresponding to the widening optical gap and more defects. That the activation energy increases with increasing Ar dilution or decreasing hydrogen dilution is due to the fact that more defect states lead to a pulling down of the Fermi level.     

Dependences of the surface and the optical properties on the O2/O2 + Ar flow-rate ratios for ZnO thin films grown on ZnO buffer layers

ZnO active layers on ZnO buffer layers were grown at various O₂/O₂ + Ar flow-rate ratios by using radio-frequency magnetron sputtering. Atomic force microscopy images showed that the surface roughnesses of the ZnO active layers grown on ZnO buffer layers decreased with decreasing O₂ atmosphere, indicative of an improvement in the ZnO surfaces. The type of the ZnO active layer was n-type, and the resistivity of the layer increased with increasing O₂ atmosphere. Photoluminescence spectra from the ZnO active layers grown on the ZnO buffer layers showed dominant peaks corresponding to local levels in the ZnO energy gap resulting from oxygen vacancies or interstitial zinc vacancies, and the peak positions changed significantly with the O₂/O₂ + Ar flow rate. These results can help improve understanding of the dependences of the surface and the optical properties on the O₂/O₂ + Ar ratio for ZnO thin films grown on ZnO buffer layers.     

Significance of the HO2 + CO reaction during the combustion of CO + H2 mixtures at high pressures

This paper constitutes an experimental and numerical study, using uncertainty analysis of the most important parameters, to evaluate the mechanism for the combustion of CO + H₂ mixtures at high pressures in the range 15-50 bar and temperatures from 950 to 1100 K. Experiments were performed in a rapid compression machine. Autoignition delays were measured for stoichiometric compositions of CO + H₂ containing between 0 and 80% CO in the total fuel mixture. The experimental results showed an unequivocal monotonic increase as the proportion of CO in the mixture was raised. Comparisons were made also with the measured ignition delays in mixtures of H₂ with increasing dilution by N₂, corresponding to the proportions of CO present. These times also increased monotonically, albeit with a greater sensitivity to the extent of dilution than those measured in the CO + H₂ mixtures. By contrast, numerical simulations for the same mixtures, based on a kinetic model derived by Davis et al. displayed a qualitative discrepancy as there was virtually no sensitivity of the ignition delay to the changing ratio of CO + H₂, certainly up to 80% replacement. No exceptions to this trend were found, despite tests being made using seven other kinetic models for CO + H₂ combustion. Global uncertainty analyses were then applied to the Davis et al. model in order to trace the origins of this discrepancy. The analyses took into account the uncertainties in all rate parameters in the model, which is a pre-requisite for evaluation against ignition delay data. It is shown that the reaction rate constant recommended by Baulch et al. for the HO₂ + CO reaction, at T ∼ 1000 K, could be up to a factor of 10 too high and that lowering this rate corrected the qualitative anomaly between experiment and numerical prediction.     

Characteristic properties of Y2SiO5:Ce thin films grown with PLD

Three different gases (nitrogen (N₂), oxygen (O₂) and argon (Ar)) were used as background gases during the growth of pulsed laser deposition (PLD) Y₂SiO₅:Ce thin films. A Krypton fluoride laser (KrF), 248 nm was used for the PLD of the films on silicon (Si) (1 0 0) substrates. The effect of the background gases on the surface morphology, crystal growth and luminescent properties were investigated. All the experimental parameters, the gas pressure (455 mT), the substrate temperature (600 °C), the pulse frequency (8 Hz), the number of pulses (4000) and the laser fluence (1.6±0.2) J/cm² were kept constant. The only parameter that was changed during the deposition was the ambient gas species. The surface morphology and average particle sizes were monitored with scanning electron microscopy (SEM) and atomic force microscopy (AFM). X-ray diffraction (XRD) and Auger electron spectroscopy (AES) were used to determine the crystal structure and composition, respectively. Cathodo- (CL) and photoluminescence (PL) were used to measure the luminescent intensities for the different phosphor thin films. The nature of the particles, ablated on the substrate, is related to the collisions between the ejected particles and the ambient gas particles. The CL and PL intensities also depend on the particle sizes. A 144 h (coulomb dose of 1.4×10⁴ C cm⁻²) electron degradation study on the thin films ablated in the Ar gas environment resulted in a decrease in the main CL intensity peak at 440 nm and to the development of a new very broad luminescent peak spectra ranging from 400 to 850 nm due to the growth of a SiO₂ layer on the surface.     

Comparison of CH4/H2 and C2H6/H2 inductively coupled plasma etching of ZnO

CH₄/H₂-based discharges are attractive for dry etching of single crystal ZnO because of their non-corrosive nature. We show that substitution of C₂H₆ for CH₄ increases the ZnO etch rate by approximately a factor of 2 both with and without any inert gas additive. The C₂H₆/H₂/Ar mixture provides a strong enhancement over pure Ar sputtering, in sharp contrast to the case of CH₄/H₂/Ar. The threshold ion energy for initiating etching is 42.4 eV for C₂H₆/H₂/Ar and 59.8 eV for CH₄/H₂/Ar. The etched surface morphologies were smooth, independent of the chemistry and the Zn/O ratio in the near-surface region was unchanged within experimental error after etching with both chemistries. The plasma etching improved the band-edge photoluminescence intensity and suppressed the deep level emission from the bulk ZnO under our conditions, due possibly to removal of surface contamination layer.     

Effects of H2 ambient annealing in fully 0 0 2-textured ZnO:Ga thin films grown on glass substrates using RF magnetron co-sputter deposition

Gallium doped zinc oxide (ZnO:Ga) thin films were grown on glass substrates using RF magnetron co-sputtering, followed by H₂ ambient annealing at 623 K to explore a possibility of steady and low-cost process for fabricating transparent electrodes. While it was observed that the ZnO:Ga thin films were densely packed c-axis oriented self-textured structures, in the as-deposited state, the films contained Ga₂O₃ and ZnGa₂O₄ which had adverse effect on the electrical properties. On the other hand, post-annealing in H₂ ambient improved the electrical properties significantly via reduction of Ga₂O₃ and ZnGa₂O₄ to release elemental Ga which subsequently acted as substitutional dopant increasing the carrier concentration by two orders of magnitude. Transmittance of the ZnO:Ga thin films were all over 90% that of glass while the optical band gap varied in accordance with the carrier concentrations due to changes in Fermi level. Experimental observation in this study suggests that transparent conductive oxide (TCO) films based on Ga doped ZnO with good electrical and optical properties can be realized via simple low-cost process.     

Correlation between optical properties and Si nanocrystal formation of Si-rich Si oxide films prepared by plasma-enhanced chemical vapor deposition

We have investigated the phase separation and silicon nanocrystal (Si NC) formation in correlation with the optical properties of Si suboxide (SiO_x, 0 < x < 2) films by thermal annealing in high vacuum. The SiO_x films were deposited by plasma-enhanced chemical vapor deposition at different nitrous oxide/silane (N₂O/SiH₄) flow ratios. The as-deposited films show increased Si concentration with decreasing N₂O/SiH₄ flow ratio, while the deposition rate and surface roughness have strong correlations with the flow ratio in the N₂O/SiH₄ reaction. After thermal annealing at temperatures above 1000 °C, Fourier transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy manifest the progressive phase separation and continuous growth of crystalline-Si (c-Si) NCs in the SiO_x films with increasing annealing temperature. We observe a transition from multiple-peak to single peak of the strong red-range photoluminescence (PL) with increasing Si concentration and annealing temperature. The appearance of the single peak in the PL is closely related to the c-Si NC formation. The PL also redshifts from ∼1.9 to 1.4 eV with increasing Si concentration and annealing temperature (i.e., increasing NC size). The good agreements of the PL evolution with NC formation and the PL peak energy with NC size distribution support the quantum confinement model.     

Determination of the rate of H + O2 + M → HO2 + M (M = N2, Ar, H2O) from ignition of syngas at practical conditions

In H₂ and H₂/CO oxidation, the H + O₂ + M termination step is one of the most important reactions at elevated pressures. With the recent, increased interest in synthetic fuels, an accurate assessment of its rate coefficient becomes increasingly important, especially for real fuel/air mixtures. Ignition delay times in shock-tube experiments at the conditions selected in this study are only sensitive to the rates of the title reaction and the branching reaction H + O₂ = OH + O, the rate of which is known to a high level of accuracy. The rate coefficient of the title reaction for M = N₂, Ar, and H₂O was determined by adjusting its value in a detailed chemical kinetics model to match ignition delay times for H₂/CO/O₂/N₂, H₂/CO/O₂/Ar, and H₂/CO/O₂/N₂/H₂O mixtures with fuel/air equivalence ratios of ? = 0.5, 0.9, and 1.0. The rate of H + O₂ + N₂ = HO₂ + N₂ was measured to be 2.7 (−0.7/+0.8) × 10¹⁵ cm⁶/mol² s for T = 916-1265 K and P = 1-17 atm. The present determination agrees well with the recent study of Bates et al. [R.W. Bates, D.M. Golden, R.K. Hanson, C.T. Bowman, Phys. Chem. Chem. Phys. 3 (2001) 2337-2342], whose rate expressions are suggested herein for modeling the falloff regime. The rate of H + O₂ + Ar = HO₂ + Ar was measured to be 1.9 × 10¹⁵ cm⁶/mol² s for T = 932-965 K and P = 1.4 atm. The rate of H + O₂ + H₂O = HO₂ + H₂O was measured to be 3.3 × 10¹⁶ cm⁶/mol² s for T = 1071-1161 K and P = 1.3 atm. These are the first experimental measurements of the rates of the title reactions in practical combustion fuel/air mixtures.     

Effect of composition and deposition temperature on the characteristics of Ga doped ZnO thin films

ZnO films doped with Ga (GZO) of varying composition were prepared on Corning glass substrate by radio frequency magnetron sputtering at various deposition temperatures of room temperature, 150, 250 and 400 °C, and their temperature dependent photoelectric and structural properties were correlated with Ga composition. With increasing deposition temperature, the Ga content, at which the lowest electrical resistivity and the best crystallinity were observed, decreased. Films with optimal electrical resistivity of 2-3 × 10⁻⁴ Ω cm and with good crystallinity were obtained in the substrate temperature range from 150 to 250 °C, and the corresponding C_Ga/(C_Ga + C_Zn) atomic ratio was about 0.049. GZO films grown at room temperature had coarse columnar structure and low optical transmittance, while films deposited at 400 °C yielded the highest figure of merit (FOM) due to very low optical absorption despite rather moderate electrical resistivity slightly higher than 4 × 10⁻⁴ Ω cm. The optimum Ga content at which the maximum figure of merit was obtained decreased with increasing deposition temperature.     

Luminescent characteristics of CaTiO3:Pr thin films prepared by pulsed laser deposition method with various substrates

CaTiO₃:Pr³⁺ films were deposited on different substrates such as Al₂O₃ (0 0 0 1), Si (1 0 0), MgO (1 0 0), and fused silica using pulsed laser deposition method. The crystallinity and surface morphology of these films were investigated by XRD and SEM measurements. The films grown on the different substrates have different crystallinity and morphology. The FWHM of (2 0 0) peak are 0.18, 0.25, 0.28, and 0.30 for Al₂O₃ (0 0 0 1), Si (1 0 0), MgO (1 0 0), and fused silica, respectively. The grain sizes of phosphors grown on different substrates were estimated by using Scherrer's formula and the maximum crystallite size observed for the thin film grown on Al₂O₃ (0 0 0 1). The room temperature PL spectra exhibit only the red emission peak at 613 nm radiated from the transition of (¹D₂ → ³H₄) and the maximum PL intensity for the films grown on the Al₂O₃ (0 0 0 1) is 1.1, 1.4, and 3.7 times higher than that of the CaTiO₃:Pr³⁺ films grown on MgO (1 0 0), Si (1 0 0), and fused Sillica substrates, respectively. The crystallinity, surface morphology and luminescence spectra of thin-film phosphors were highly dependent on substrates.     

Infrared optical properties of Ba(Zr0.20Ti0.80)O3 and Ba(Zr0.30Ti0.70)O3 thin films prepared by sol-gel method

Ba(Zr_xTi_1−x)O₃ (BZT) (x = 0.20 and 0.30) thin films are deposited on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrate by sol-gel method. X-ray diffraction patterns show that the thin films have a good crystallinity. Optical properties of the films in the wavelength range of 2.5-12 μm are studied by infrared spectroscopic ellipsometry (IRSE). The optical constants of the BZT thin films are determined by fitting the IRSE data using a classical dispersion formula. As the wavelength increases, the refractive index decreases, while the extinction coefficients increase. The effective static ionic charges are derived, which are smaller than that in a purely ionic material for the BZT thin films.     

Crystalline and photoluminescence characteristics of YVO4:Sm thin films grown by pulsed laser deposition under oxygen pressure

YVO₄:Sm³⁺ films were deposited on Al₂O₃ (0 0 0 1) substrates at various oxygen pressures changing from 13.3 to 46.6 Pa by using the pulsed laser deposition method. The crystallinity and surface morphology of these films were investigated by means of X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. The XRD pattern confirmed that YVO₄:Sm³⁺ film has zircon structure and the AFM study revealed that the films consist of homogeneous grains ranging from 100 to 400 nm. The room temperature photoluminescence (PL) spectra showed that the emitted radiation was dominated by a reddish-orange emission peak at 602 nm radiating from the transition of (⁴G_5/2→⁶H_7/2). The crystallinity, surface morphology, and photoluminescence spectra of thin-film phosphors were highly dependent on the deposition conditions, in particular, the substrate temperature. The surface roughness and photoluminescence intensity of these films showed similar behavior as a function of oxygen pressure.     

使用发射光谱对H2稀释情况下的感应耦合H2/C4F8等离子体中碳氟基团的研究

在射频输入功率为400W，气压为0.8Pa的条件下，使用光强标定的发射光谱方法研究了感应耦合H₂/C₄F₈等离子体中CF, CF₂, H和F基团的相对密度随流量比R=H₂/(H₂+C₄F₈)的变化情况，而HF基团相对密度的变化由四级质谱仪探测得到。结果表明等离子体活性先随着R的增加而升高，然后随着R的进一步增加而下降。在流量比从0逐渐上升到0.625的过程中，CF和CF₂基团的相对密度不断降低。实验中测得的CF基团的相对密度[CF]与理论计算得到的[CF]有很好的一致性说明了电子与CF2基团的碰撞反应是CF基团产生的主要原因。文中还讨论了HF基团。     

Structure, magnetic and optical properties of polycrystalline Co-doped TiO2 films

Co-doped TiO₂ films were fabricated under different conditions using reactive facing-target magnetron sputtering. Co doping improves the transformation of TiO₂ from anatase phase to rutile phase. The chemical valence of doped Co in the films is +2. All the films are ferromagnetic with a Curie temperature above 340 K. The average room-temperature moment per Co of the Co-doped TiO₂ films fabricated at 1.86 Pa decreases from 0.74 μ_B at x=0.03 to 0.02 μ_B at x=0.312, and decreases from 0.54 to 0.04 μ_B as x increases from 0.026 to 0.169 for the Co-doped TiO₂ films fabricated at 0.27 Pa. The ferromagnetism originates from the oxygen vacancies created by Co²⁺ dopants at Ti⁴⁺ cations. The optical band gaps value (E_g) of the Co-doped TiO₂ films fabricated at 1.86 Pa decreases linearly from 3.35 to 2.62 eV with the increasing x from 0 to 0.312. For the Co-doped TiO₂ films fabricated at 1.86 Pa, the E_g decreases linearly from 3.26 to 2.53 eV with increasing x from 0 to 0.350.     

Photocatalytic property of TiO2 thin films sputtered-deposited on unheated substrates

TiO₂ films deposited on unheated substrates of alumina silicate glass by rf. (13.56 MHz) magnetron sputtering in the mixture of O₂ and Ar gases have been studied with X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and optical spectroscopy. Structural and optical properties of TiO₂ films deposited at different O₂ concentrations and total pressures have been analyzed. Photocatalytic properties of TiO₂ films were characterized by following the degradation of methylene blue molecules under UV irradiation. It was found that the rate of methylene blue decomposition strongly depends on morphology and crystallinity of the deposited films, namely on the content of the anatase phase and on the size of the anatase grains. The best photocatalytic activity was found on TiO₂ films consisting of pure anatase phase with the size of grains of about 450 Å. With the help of those films a thin film reactor for water purification has been designed and tested.     

Formation of silicon nanodots from dysprosium-doped amorphous SiCxOy films grown by hot-filament assisted chemical vapor deposition of CH3SiH3 and Dy(DPM)3 gas jets

We report on Si nanodot formation by chemical vapor deposition (CVD) of ultrathin films and following oxidation. The film growth was carried out by hot-filament assisted CVD of CH₃SiH₃ and Dy(DPM)₃ gas jets at the substrate temperature of 600 °C. The transmission electron microscopy observation and X-ray photoelectron spectroscopy analysis indicated that ∼35 nm Dy-doped amorphous silicon oxycarbide (SiC_xO_y) films were grown on Si(1 0 0). The Dy concentration was 10-20% throughout the film. By further oxidation at 860 °C, the smooth amorphous film was changed to a rough structure composed of crystalline Si nanodots surrounded by heavily Dy-doped SiO₂.