PS colloidal particles stabilized by graphene oxide

Exfoliated graphene oxide (GO) sheets with hydrophilic functional groups on the surface were prepared by the oxidation of graphite. Because of the hydrophilic groups on the sheets and the hydrophobic carbon surface, GO sheets were located at the oil-water interface and could be used as a stabilizer in Pickering emulsions. After the Pickering emulsion polymerization of styrene, PS colloidal particles with GO sheets on the surface were prepared. The size of the GO sheets exerts an important influence on the preparation of PS colloidal particles. Small GO sheets located at the liquid-liquid interface and GO-stabilized PS colloidal particles were prepared; however, for large GO sheets, smaller PS colloidal particles prepared on the GO surface were observed. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) were used to characterize the structure and morphology of the colloidal particles. TEM, SEM, and XPS results all suggest the successful preparation of GO-stabilized PS colloidal particles.     

pH dependent stability of aqueous suspensions of graphene with adsorbed weakly ionisable cationic polyelectrolyte

Stable graphene suspensions were prepared through ultrasonic exfoliation followed by surface modification with the cationic polyelectrolyte poly(ethyleneimine) (PEI). The stability of the suspensions was found to be dependent upon the pH of the solution and the molecular weight of the PEI adsorbed. For the graphene sheets with adsorbed PEI with a molecular weigh of 600 Da, the particles were stabilised through an increased electrostatic repulsion at low pH inferred from in an increase in the measured zeta potential of the particles. However, the graphene with higher molecular weight PEI (70 kDa) was stable over a comparatively larger pH range through a combination of electrostatic repulsion at low pH and steric repulsion at elevated pH. Thus, solution conditions allowing the control of the colloidal sized graphene particles can be easily tuned through judicious management of solution conditions as well as polymer layer properties.     

Covalent polymeric modification of graphene nanosheets via surface‐initiated single‐electron‐transfer living radical polymerization

Graphene nanosheets offer intriguing electronic, thermal, and mechanical properties and are expected to find a variety of applications in high‐performance nanocomposite materials. Dispersal of graphene nanosheets in polymer hosts and precise interface control are challenging due to their strong interlayer cohesive energy and surface inertia. Here, an efficient strategy is presented for growing polymers directly from the surface of reduced graphene oxide (GO). This method involves the covalent attachment of Br‐containing initiating groups onto the surface of hydrazine hydrate reduced GO via a diazonium addition and the succeeding linking of poly(tert‐butyl methacrylate) (PtBMA) chains (71.7 wt % grafting efficiency) via surface‐initiated single‐electron‐transfer living radical polymerization (SET‐LRP) to graphene nanosheets. The resulting materials were characterized by using a range of testing techniques and it was proved that polymer chains were successfully introduced to the surface of exfoliated graphene sheets. After grafting with PtBMA, the modified graphene sheets still maintained the separated single layers, and the dispersibility was improved significantly. The method is believed to offer possibilities for optimizing the processing properties and interface structure of graphene–polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Electrically conductive nanocomposites with segregated structure based on poly(vinylidene fluoride-<Emphasis Type="Italic">co</Emphasis>-tetrafluoroethylene) and reduced graphene oxide

An approach was described to obtaining polymer composites with segregated structure that have high electrical conductivity at low concentrations of an electrically conductive filler. According to this approach, thin layers of electrically nonconductive nanodispersed graphene oxide are applied to the surface of polymer particles and conduction is produced by heat and chemical treatments. Hot pressing of the modified powder leads to combination of layers of the graphene-like filler to form a single electrically conductive network. For the first time, reduction of graphene oxide on the surface of polymer particles with hydrazine vapor at room temperature was performed. Comparison of the electrical conductivities of composites obtained by the thermal and chemical methods of graphene oxide reduction showed that the chemical reduction method gives composites with higher conductivities than the thermal method does. The maximum conductivity (0.5 S/m) was reached in a composite containing 0.6% chemically reduced graphene oxide.     

The mechanism of fluidization of concentrated calcium carbonate slurries by poly(oxyethylene) diphosphonates

Nonionic poly(oxyethylene) polymers having a diphosphonate group at one chain end strongly adsorb onto CaCO₃ particles. The main consequence is a considerable lowering of the viscosity of concentrated slurries. This effect occurs because of the break up and redispersion of aggregates of flocculated CaCO₃ particles by the polymer adsorption. The mechanism of colloidal stabilization is steric, the particles becoming uncharged as the polymer adsorbs at their surface. As a consequence, the colloidal suspensions remain stable and fluid at high volume fractions and at high ionic strengths. On the other hand, because of the strong affinity of these polymers for CaCO₃ surfaces, the larger part of the polymer is adsorbed until the coverage of the particles reaches completion. The easy to handle polymer-to-solid weight ratio can then be used as a formulation parameter. The depletion flocculation by the nonadsorbed polymer is avoided. Received: 12 March 1999 Accepted in revised form: 2 July 1999     

Colloid surface engineering via deposition of multilayered thin films from polyelectrolyte blend solutions

Multilayer thin films were constructed on polystyrene colloidal particles by depositing alternating layers of poly(allylamine hydrochloride) (PAH) at pH 7.5 and varying composition blends of poly(acrylic acid) (PAA) and poly(styrenesulfonate) (PSS) at pH 3.5. Following the deposition of each layer, microelectrophoresis experiments showed alternating zeta-potentials, suggesting the formation of multilayered films on the particles. Scanning and transmission electron microscopy were used to examine the surface morphology of the colloidal particles, with homogeneous surface coatings apparent for films deposited from PAA/PSS blend solutions containing up to 90 wt % PAA. The colloidal stability of these particles is greater than those coated with individual PAH and PAA layers. In the case of the blend PAA/PSS = 25:75 wt %, up to 20 layers were assembled without compromising the colloidal stability of the dispersion. The results demonstrate that the deposition of layers from PE blend solutions containing a strong and weak PE can be used as a facile method for controlling the surface properties and hence the colloidal stability of core-shell particles, as well as the thickness and morphology of the coatings. Control of these parameters is important for subsequent processing and application of these particles in controlled delivery, photonics, catalytic, and separation applications.     

Synthesis of polystyrene nanoparticles “armoured” with nanodimensional graphene oxide sheets by miniemulsion polymerization

Polystyrene particles “armoured” with nanosized graphene oxide (GO) sheets have been prepared by aqueous miniemulsion polymerization of styrene, exploiting the amphiphilic properties of GO in the absence of conventional surfactants. The nanoscale GO sheets were prepared from graphite nanofibers of diameter approximately 100 nm based on a novel procedure, thus effectively ensuring the absence of larger sheets. Polymerization proceeded to high conversion with minor coagulation, with final number‐average particle diameters of approximately 500 nm, but relatively broad particle size distributions. Scanning electron microscopy analysis revealed particles with a textured surface, consistent with the expected morphology. Interestingly, analysis of GO sheets recovered from the polymerization revealed that the GO sheets are partially reduced during the polymerization—approximately 50% of the initial carboxyl groups of the GO were lost, consistent with some loss in colloidal stability at high conversion. The overall approach offers a convenient and attractive synthetic route to novel graphene‐based polymeric nanostructures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Interfacial rheology and structure of tiled graphene oxide sheets

The hydrophilic nature of graphene oxide sheets can be tailored by varying the carbon to oxygen ratio. Depending on this ratio, the particles can be deposited at either a water-air or a water-oil interface. Upon compression of thus-created Langmuir monolayers, the sheets cover the entire interface, assembling into a strong, compact layer of tiled graphene oxide sheets. With further compression, the particle layer forms wrinkles that are reversible upon expansion, resembling the behavior of an elastic membrane. In the present work, we investigate under which conditions the structure and properties of the interfacial layer are such that free-standing films can be obtained. The interfacial rheological properties of these films are investigated using both compressional experiments and shear rheometry. The role of surface rheology in potential applications of such tiled films is explored. The rheological properties are shown to be responsible for the efficiency of such layers in stabilizing water-oil emulsions. Moreover, because of the mechanical integrity, large-area monolayers can be deposited by, for example, Langmuir-Blodgett techniques using aqueous subphases. These films can be turned into transparent conductive films upon subsequent chemical reduction.     

Stabilization of graphene sheets by a structured benzene/hexafluorobenzene mixed solvent

Applications requiring pristine graphene derived from graphite demand a solution stabilization method that utilizes an easily removable media. Using a combination of molecular dynamics simulations and experimental techniques, we investigate the solublization/suspension of pristine graphene sheets by an equimolar mixture of benzene and hexafluorobenzene (C(6)H(6)/C(6)F(6)) that is known to form an ordered structure solidifying at 23.7 °C. Our simulations show that the graphene surface templates the self-assembly of the mixture into periodic layers extending up to 30 ? from both sides of the graphene sheet. The solvent structuring is driven by quadrupolar interactions and consists of stacks of alternating C(6)H(6)/C(6)F(6) molecules rising from the surface of the graphene. These stacks result in density oscillations with a period of about 3.4 ?. The high affinity of the 1:1 C(6)H(6)/C(6)F(6) mixture with graphene is consistent with observed hysteresis in Wilhelmy plate measurements using highly ordered pyrolytic graphite (HOPG). AFM, SEM, and TEM techniques verify the state of the suspended material after sonication. As an example of the utility of this mixture, graphene suspensions are freeze-dried at room temperature to produce a sponge-like morphology that reflects the structure of the graphene sheets in solution.     

Polymer sheets with a thin nanocomposite layer acting as a UV filter

A surface layer (thickness 1–10 μm) containing colloidal TiO₂ or ZnO particles was prepared in EVA (a copolymer of ethylene and vinyl acetate). The inorganic particles were formed in situ by hydrolysis of incorporated titanium tetrachloride or diethyl zinc. The resulting materials were analyzed with UV spectroscopy, electron microscopy, X-ray diffraction, thermogravimetric analysis and atomic emission spectroscopy. The average diameter of the embedded TiO₂ particles was 70 nm; these particles absorb UV radiation but also induce opacity in the polymer sheets in the visible wavelengths range. The ZnO particles were smaller (average diameter 15 nm); with a surface layer of embedded ZnO, transparent polymer sheets can be obtained that absorb UV radiation. © 1997 John Wiley & Sons, Ltd.     

Theoretical study of cooperativity in multivalent polymers for colloidal stabilization

Multivalent polymers, i.e., copolymers with multiple binding sites, have been proposed recently for stabilization of fusogentic liposomes and other liposomal colloids useful for drug delivery. The performance of such polymers critically depends on their molecular architecture, in particular the strength and frequency of surface anchoring sites along the backbone of a highly soluble polymer. In this work, we investigate the adsorption and surface forces due to multivalent polymers based on coarse-grained polymer models. We find that for W-type polymers that form dangling tails when all anchoring segments are attached to a surface, increasing the chain length at fixed polymer composition leads to a stronger repulsive barrier in the polymer-mediated surface forces thereby increasing the ability of the polymer to stabilize colloidal particles. This prediction conforms to an earlier experiment indicating that increasing the number of hydrophobic anchors along poly(ethylene glycol) polymers results in the cooperative behavior for both surface adsorption and steric stabilization. For M-type multivalent polymers that have weakly anchoring sites placed at the ends, however, addition of binding sites at fixed polymer composition could lead to negative cooperativity, i.e., the more binding sites, the less the amount of adsorption or the weaker the ability of surface protection. The theory also predicts that polymers with two anchoring sites (e.g., telechelic copolymers) are most efficient for colloidal stabilization.     

Electrochemical interfacial capacitance in multilayer graphene sheets: Dependence on number of stacking layers

We engineered the number of stacking layers of multilayer graphene sheets by selective post-treatments. The most probable number of layers of graphene was determined according to specific surface area. The interfacial capacitance of multilayer graphene sheets relates to the number of layers. This result is attributed to the dependence of space charge layer capacitance on the number of layers.     

Langmuir-Blodgett assembly of graphite oxide single layers

Single-layer graphite oxide can be viewed as an unconventional type of soft material and has recently been recognized as a promising material for composite and electronics applications. It is of both scientific curiosity and technical importance to know how these atomically thin sheets assemble. There are two fundamental geometries of interacting single layers: edge-to-edge and face-to-face. Such interactions were studied at the air-water interface by Langmuir-Blodgett assembly. Stable monolayers of graphite oxide single layers were obtained without the need for any surfactant or stabilizing agent, due to the strong electrostatic repulsion between the 2D confined layers. Such repulsion also prevented the single layers from overlapping during compression, leading to excellent reversibility of the monolayers. In contrast to molecular and hard colloidal particle monolayers, the single layers tend to fold and wrinkle at edges to resist collapsing into multilayers. The monolayers can be transferred to a substrate, readily creating a large area of flat graphite oxide single layers. The density of such films can be continuously tuned from dilute, close-packed to overpacked monolayers of interlocking single layers. For size-mismatched single layers, face-to-face interaction caused irreversible stacking, leading to double layers. The graphite oxide monolayers can be chemically reduced to graphene for electronic applications such as transparent conducting thin films.     

Stabilization of magnetorheological suspensions by polyacrylic acid polymers

This work is devoted to the synthesis and stabilization of magnetorheological suspensions constituted by monodisperse micrometer-sized magnetite spheres in aqueous media. The electrical double-layer characteristics of the solid/liquid interface were studied in the absence and presence of adsorbed layers of high molecular weight polyacrylic acids (PAA; Carbopol). Since the Carbopol-covered particles can be thought of as "soft" colloids, Ohshima's theory was used to gain information of the surface potential and the charge density of the polymer layer. The effect of the pH of the solution on the double-layer characteristics is related to the different conformations of the adsorbed molecules provoked by the dissociation of the acrylic groups present in polymer molecules. The stability of the suspensions was experimentally studied for different pH and polymer concentrations, and in the absence or presence of a weak magnetic field applied. The stability of the suspensions was explained using the classical DLVO theory of colloidal stability extended to account for hydration, steric, and magnetic interactions between particles. Diagrams of potential energy vs interparticle distance show the predominant effect of steric, hydrophilic/hydrophobic, and magnetic interactions on the whole stability of the system. The best conditions to obtain stable suspensions were found when strong steric and hydrophilic repulsions hinder the coagulation between polymer-covered particles, simultaneously avoiding sedimentation by the thickening effect of the polymer solution. When a not too high molecular weight PAA was employed in a low concentration, the task of a long-time antisettling effect compatible with the desired magnetic response of the fluid was achieved.     

Influence of added particles on the phase behavior of polymer solutions. Analysis by mean-field lattice theory

The influence of added colloidal particles on the phase stability of polymer solutions is investigated theoretically. The polymer has an affinity to the particle surface. A mean-field lattice theory based on the Flory-Huggins theory is used to calculate the phase behavior in solutions containing a single polymer component and particles. The particles are described in two different ways. The first approach considers the surface free energy associated with added solid particles and the mixing entropy of the particles. In the second approach, the particles are simply modeled as large polymers. Both ways of describing the added particles show that the added particles decrease the stability of the polymer solution when the polymer-particle attraction is strong. A higher particle concentration enhances the effect. Experiments where polystyrene latex particles are added at different concentrations to aqueous dispersions of ethyl(hydroxyethyl)cellulose (EHEC) support the theoretical findings.     

Stable aqueous dispersion of reduced graphene nanosheets via non-covalent functionalization with conducting polymers and application in transparent electrodes

We developed a simple and facile method of producing a stable aqueous suspension of reduced graphene oxide (RGO) nanosheets through the chemical reduction of graphene oxide in the presence of a conducting polymer dispersant, poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). This approach involves the cooperative interactions of strong π- π interactions between a two-dimensional graphene sheet and a rigid backbone of PEDOT and the intermolecular electrostatic repulsions between negatively charged PSS bound on the RGO sheets, which impart the colloidal stability of the resulting hybrid nanocomposite of RGO/PEDOT. Moreover, our one-step solution-based method allows preserving the intrinsic chemical and electronic properties of both components, yielding a hybrid film of RGO nanosheets of high conductivity of 2.3 kΩ/sq with a transmittance of 80%. By taking advantage of conducting network structure of conducting polymers which provides an additional flexibility and mechanical stability of RGO nanosheets, we demonstrate the potential application of hybrid RGO/PEDOT as highly flexible and transparent electrodes.     

Surface chemistry and rheology of polysulfobetaine-coated silica

We have measured the viscosity of suspensions of colloidal silica particles (d = 300 nm) and the properties of silica surfaces in solutions of a polymer consisting of zwitterionic monomer groups, poly(sulfobetaine methacrylate), polySBMA. This polymer has potential use in modifying surface properties because the polymer is net uncharged and therefore does not generate double-layer forces. The solubility of the polymer can be controlled and varies from poor to good by the addition of sodium chloride salt. Ellipsometry was used to demonstrate that polySBMA adsorbs to silica and exhibits an increase in surface excess at lower salt concentration, which is consistent with a smaller area per molecule at low salt concentration. Neutron reflectivity measurements show that the adsorbed polymer has a thickness of about 3.7 nm and is highly hydrated. The polymer can be used to exercise considerable control over suspension rheology. When silica particles are not completely covered in polymer, the suspension produces a highly viscous gel. Atomic force microscopy was used to show this is caused by bridging of polymer between the particles. At higher surface coverage, the polymer can produce either a high or very low viscosity slurry depending on the sodium chloride concentration. At high salt concentration, the suspension is stable, and the viscosity is lower. This is probably because the entrainment of many small ions renders the polymer film highly hydrophilic, producing repulsive surface forces and lubricating the flow of particles. At low salt concentrations, the polymer is barely soluble and more densely adsorbed. This produces less stable and more viscous solutions, which we attribute to attractive interactions between the adsorbed polymer layers.     

Synthesis and immobilization of micro-scale drug particles in cellulosic films

The anti-solvent synthesis of micron-scale particles, their stabilization, and subsequent self-assembly into polymer films suitable for drug delivery is presented. The colloidal particles were stabilized using low molecular weight hydroxypropyl methylcellulose (HPMC), while drug encapsulation was carried out with high molecular weight HPMC and polyvinylpyrrolidone (PVP). Griseofulvin (GF) was used as the model drug compound, and the polymer films were evaluated in terms of their surface morphology, mechanical properties and in vitro drug release. In general, the release rates were best described by first-order and Hixson-Crowell kinetic models, and in a typical film containing 57% HPMC, 100% of GF was released within 50 min.     

Functional colloidal particles stabilized by layered silicate with hydrophilic face and hydrophobic polymer brushes

In this study, we describe a new strategy for producing narrowly dispersed functional colloidal particles stabilized by a nanocomposite with hydrophilic clay faces and hydrophobic polystyrene (PS) brushes on the edges. This method involves preparation of polymer brushes on the edges of clay layers and Pickering suspension polymerization of styrene in the presence of the nanocomposites. PS brushes on the edges of clay layers were prepared by atom transfer radical polymerization. X‐ray diffraction and thermogravimetric analysis results indicated that PS chains were grafted to the edges of clay platelets. Transmission electron microscope results showed that different morphologies of clay‐PS particles could be obtained in different solvents. In water, clay‐PS particles aggregated together, in which PS chains collapsed forming nanosized hydrophobic domains and hydrophilic clay faces stayed in aqueous phase. In toluene, clay‐PS particles formed face‐to‐face structure. Narrowly dispersed PS colloidal particles stabilized by clay‐PS were prepared by suspension polymerization. Because of the negatively charged clay particles on the surface, the zeta potential of the PS colloidal particles was negative. Positively charged poly(2‐vinyl pyridine) (P2VP) chains were adsorbed to the surface of PS colloidal particles in aqueous solution at a low pH value, and gold nanoparticles were prepared in P2VP brushes. Such colloidal particles may find important applications in a variety of fields including waterborne adhesives, paints, catalysis of chemical reactions, and protein separation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1535–1543, 2009     

Interaction of cationic liposomes with cell membrane models

The colloidal dispersion stability of nano-sized graphene sheets in supercritical fluid (SCF) media is very important for developing SCF-based exfoliation and dispersion technologies for stabilization and solubilization of graphenes. We carried out molecular dynamics simulations to elucidate the stability mechanism of graphene in supercritical CO(2) (scCO(2)). The potential of mean force (PMF) between two graphene nanosheets in scCO(2) was simulated, and the effect of scCO(2) density and temperature on the PMF behavior has been investigated. The simulation results demonstrate that there exists a free energy barrier between graphenes in the scCO(2) fluid, possibly obstructing the aggregation of graphenes. The single-layer confined CO(2) molecules between the graphene sheets can induce a dominating repulsion interaction between graphene sheets. At higher scCO(2) fluid density, there are more confined CO(2) molecules within the interplate regions, resulting in a stronger repulsive free energy barrier. The effect of temperature on the PMF is relatively minor. The scCO(2) solvent structure shows layered confined arrangement in the interfacial region near the graphene nanosheets, which is correlated well with the PMF profile curve.