可见光响应碳掺杂的光催化剂涂覆于塞流反应器上分解气态芳香化合物(英文)

A plug‐flow reactor coated with carbon‐doped TiO2 (C‐TiO2 ) powder was investigated for the control of vaporous aromatics (benzene, toluene, ethylbenzene, and o‐xylene (BTEX)) under a range of experimental conditions. The characteristics of the as‐prepared C‐TiO2 and a reference Degussa P25 TiO2 powder were examined using X‐ray diffraction, scanning electron microscopy, diffuse‐reflectance ultraviolet‐visible‐near infrared spectroscopy, and Fourier transform infrared spectroscopy. The experimental conditions for the photocatalytic performance of the as‐prepared C‐TiO2 photocatalyst were controlled using three operational parameters, relative humidity, flow rate, and input concentration. Unlike other target compounds, very little benzene was removed by the C‐TiO2 photocatalyst under visible‐light irradiation. In contrast, the C‐TiO2 exhibited higher removal efficiencies for the other three target compounds (toluene, ethylbenzene, and xylene) compared with those achieved using unmodified TiO2 under visible‐light irradiation. The highest removal efficiency was obtained at a relative humidity value of 45%. Specifically, the toluene removal efficiency determined at a relative humidity of 45% was 78%, whereas it was close to 0%, 7.2%, and 5.5% for relative humidity values of 20%, 70%, and 95%, respectively. In addition, the removal efficiencies for the three target compounds decreased as the flow rate or input concentration increased. These findings indicate that the as‐prepared C‐TiO2 photocatalyst could be used for the removal of toxic vaporous aromatics under optimized operating conditions.     

Ag2S-石墨烯/TiO2的声化学法合成及可见光催化活性（英文）

Ag2S‐graphene/TiO2 composites were synthesized by a facile sonochemical method.The products were characterized by X‐ray diffraction,scanning electron microscopy,energy dispersive X‐ray spectroscopy,transmission electron microscopy,and UV‐Vis diffuse reflectance spectrophotometry.During the synthesis reaction,the reduction of graphene oxide and loading of Ag2S and TiO2 particles were achieved.The Ag2S‐graphene/TiO2 composites possessed a large adsorption capacity for dyes,an extended light absorption range,and efficient charge separation properties.Hence,in the photodegradation of rhodamine B,a significant enhancement in the reaction rate was observed with the Ag2S‐graphene/TiO2 composites as compared to pure TiO2.The generation of reactive oxygen species was detected by the oxidation of 1,5‐diphenyl carbazide to 1,5‐diphenyl carbazone.The high activity was attributed to the synergetic effects of high charge mobility and the red shift in the absorption edge of the Ag2S‐graphene/TiO2 composites.     

超声辅助法合成的石墨烯-TiO2复合材料声催化降解罗丹明B（英文）

A series of graphene-TiO2 composites was fabricated from graphene oxide and titanium n-butoxide(TNB) by an ultrasonic-assisted method.The structure and composition of the nanocomposites were characterized by Raman spectroscopy,BET surface area measurements,X-ray diffraction,transmission electron microscopy,and ultraviolet-visible absorption spectroscopy.The average size of the TiO2 nanoparticles on the graphene nanosheets was controlled at around 10-15 nm without using surfactant,which is attributed to the pyrolysis and condensation of dissolved TNB into TiO2 by ultrasonic irradiation.The catalytic activity of the composites under ultrasonic irradiation was determined using a rhodamine B(RhB) solution.The graphene-TiO2 composites possessed a high specific surface area,which increased the decolorization rate for RhB solution.This is because the graphene and TiO2 nanoparticles in the composites interact strongly,which enhances the photoelectric conversion of TiO2 by reducing the recombination of photogenerated electron-hole pairs.     

CoS2-碳(C60,石墨,碳纳米管)/TiO2复合光敏剂光降解有机染料（英文）

CoS2,CoS 2-C60 /TiO2,CoS2-CNT/TiO2,and CoS2-Graphene/TiO2 were prepared.The TiO2 products had the anatase phase structure and interesting surface compositions.X-ray diffraction patterns of the CoS2-carbon/TiO2 composites showed a single and clear anatase phase and the CoS2 structure.Scanning electron microscopy characterization of the texture on the CoS 2-carbon/TiO2 composites showed a homogenous composition.Energy-dispersive X-ray spectra for elemental identification showed the presence of C and Ti with strong Co and S peaks from the CoS2-carbon/TiO2 composites.The composites obtained were also characterized by transmission electron microscopy and UV-Vis spectroscopy.CoS2-carbon/TiO2 composites showed excellent photocatalytic activity for the degradation of methylene blue under visible light irradiation.This was attributed to both photocatalysis on the TiO2 support and charge transfer by the carbon nanomaterial,and the introduction of CoS2 to enhance transfer of photogenerated electrons.     

Effect of Binder on the Structure and Properties of Silicon Powder-supported TiO_2 Photocatalysis Material

Recoverable TiO2 photocatalysis material supported by silicon powder was prepared with sol-gel method, afterwards the silica gol and sodium silicate were used as molding binder respectively to investigate their effects （including binder type and binder addition quantity） on the crystal structure and catalysis properties of photocatalyst. In this work, the catalysis activity was defined as the degradation rate of methyl orange solution upon ultraviolet lamp irradiation, and the specific areas were determined with nitrogen desorption method. TiO2 crystal form was measured with X-ray powder diffraction and their micro-morphology was observed with SEM. Experimental results indicate that these two binders do not affect the crystal form transformation of TiO2, but silica gol can increase the specific surface area of TiO2 photocatalyst obviously and the addition of sodium silicate can decrease it. In all, silica gol is a better candidate than sodium silicate for higher catalysis property. In conclusion, 6% silica gol is the optimal addition concentration. Under this condition, the ratio of anatase to rutile TiO2 is 64：36, the specific area is 29.67 m^2/g, and as expected, the degradation rate of methyl orange could be as high as 90% after irradiation for 5 days.     

可见光下具有高光子效应和光催化活性的CuS-石墨烯氧化物/TiO2复合材料的制备（英文）

CuS-graphene oxide/TiO2 composites were prepared using a sol-gel method to improve the photocatalytic performance of the photocatalyst. The composites were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, and transmission electron microscopy. The photocatalytic activities were examined by the degradation of methylene blue (MB) under visible-light irradiation. The photodegradation of MB under visible-light irradiation reached 90.1% after 120 min. The kinetics of MB degradation was plotted alongside the values calculated from the Langmuir-Hinshelwood equation. The CuS-graphene oxide/TiO2 sample prepared using 0.2 mol of TiO2 showed the best photocatalytic activity. This was attributed to a cooperative reaction as a result of increased photoabsorption by graphene oxide and an increased photocatalytic effect by CuS.     

Properties of TiO2-SiO2 Mixed Oxides and Photocatalytic Oxidation of Heptane and Sulfur Dioxide

A series of TiO2-XSiO2[X denotes the molar fraction(%) of silica in the mixed oxides] with different n(Ti)/n(Si) ratios was prepared with ammonia water as a hydrolysis catalyst. The photocatalysts prepared were characterized by XRD, thermal analysis, FTIR, UV-Vis and SPS. The characterization results of FTIR and UV-Vis spectra show that Ti atoms were gradually changed from octahedral coordination to tetrahedral coordination with the addition of silica, which is not beneficial for obtaining strong Bronsted acidity and higher photocatalytic activity. The photocatalytic activity experiments, which were conducted by using heptane (or SO2) as the model reactant, showed that TiO2-SiO2 containing a suitable amount of silica can exhibit much higher photocataiytic activity than pure TiO2. The enhanced photocatalytic activity can be attributed tothree following factors.. (1) smaller crystalline size;(2) higher thermal stability; (3) the new strong Broensted acidity.     

In situ FTIR Investigation of Magnetic Field Effect on Heterogeneous Photocatalytic Degradation of Benzene over Pt/TiO2

In situ FTIR spectroscopy was utilized to investigate the magnetic field effect on the heterogeneous photocatalytic degradation of benzene over platinized titania （Pt/TiO2）. The results revealed that the employment of magnetic field may not change the mechanism of photocatalytic degradation of benzene, however, it greatly facilitate the conversion of benzene to phenol and quinone, as well as the transformation from phenol to quinone, resulting in opening the benzene ring easily and promoting the production of CO2.     

Preparation and Photocatalytic Properties of Ti1-xZrxO2 Solid Solution

A series of Ti1-xZrxO2 materials were synthesized through a multistep sol-gel process. The structural characteristics were investigated using X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS） and Raman measurements. The experimental results showed that a solid solution could be obtained at low Zr/（Ti＋Zr） molar ratios （x ≤0.319）. Raman measurements exhibited that the presence of zirconium in the solid solutions greatly retarded the amorphous-anatase and anatase-rutile transitions. The diffuse reflectance UV-Vis spectra revealed that the bandgap of the solid solution was enlarged gradually with the increment of incorporated zirconium content. The Ti1-xZrxO2 solid solutions exhibited higher photocatalytic activity than pure TiO2 for the degradation of 4-chlorophenol aqueous solution.     

邻二甲苯选择氧化V-Ti-O复合氧化物超细微粒催化剂

The structure and catalytic properties of V Ti O ultrafine particle catalyst for selective oxidation of o xylene have been studied. TEM and XRD results show that the particle size is in the range of 20～40 nm, and vanadium oxide is highly dispersed in TiO 2 (anatase). The catalytic activity of the V Ti O ultrafine particle catalyst for selective oxidation of o xylene to phthalic anhydride(PA) is higher than that of the larger oxide particles with the same catalyst composition prepared by impregnation and coprecipitation methods, indicating that the ultrafine V Ti O oxide particles are potentially new catalytic materials for the selective oxidation of o xylene to phthalic anhydride.     

Photocatalysis of low-concentration gaseous organic pollutants over electrospun iron-doped titanium dioxide nanofibers

In this study, iron-doped titania (Fe–TiO₂) nanoparticles were prepared and then coupled to a polymer material as a support to synthesize Fe–TiO₂ nanofibers for photocatalytic degradation of gaseous pollutants (benzene, toluene, ethyl benzene, and o-xylene (BTEX)) at environmental sub-ppm levels. The characteristics of as-prepared photocatalysts were determined by SEM, XRD, and FTIR analyses. Spectral analysis of the as-prepared photocatalysts revealed that they were closely associated with the characteristics of Fe ions for Fe–TiO₂ nanofibers. The photocatalytic degradation efficiencies (PDEs) of BTEX determined via Fe–TiO₂ nanofibers varied with the ratios of Fe to Ti, suggesting the presence of an optimal Fe-to-Ti ratio. In addition, the PDEs of BTEX determined via two Fe–TiO₂ nanofibers with low Fe-to-Ti ratios (0.001 and 0.004) were higher than those obtained from the undoped Fe–TiO₂ nanofibers, whereas those of the other two Fe–TiO₂ nanofibers with high Fe-to-Ti ratios (0.008 and 0.012) were lower. The average PDEs of BTEX decreased from 34 to 9%, 68 to 28%, 83 to 45%, and 90 to 55%, respectively, as the stream flow rates increased from 1 to 4 L min⁻¹. These values also decreased with increasing initial concentration (IC). Specifically, at the lowest IC of 0.1 ppm, the average PDEs of BTEX were 33, 68, 83, and 91%, respectively, while they were 5, 8, 12, and 23%, respectively, at the highest IC of 2.0 ppm. Similarly, the PDEs of BTEX decreased significantly as the RH increased. Overall, the electrospun Fe–TiO₂ nanofibers could be used to effectively decompose low-concentration gaseous organic pollutants when operational conditions were optimized.     

Preparation of TiO<Subscript>2</Subscript>/activated carbon with Fe ions doping photocatalyst and its application to photocatalytic degradation of reactive brilliant red K2G

Titanium dioxide coated on activated carbon (AC) with Fe ions doping (Fe-TiO₂/AC) composite was prepared by an improved sol-gel method. The photocatalytic activities were tested by photocatalytic degradation of reactive brilliant red K2G in solution. The results show that in comparison with the agglomeration of pure TiO₂, the TiO₂ nanoparticles are well dispersed in the AC matrix, of which sizes are decreased with Fe ions doping. Additionally, the iron species on TiO₂ of composite are Fe₂O₃ and FeO, which do not affect the crystalline structures of TiO₂ nanoparticles. The AC matrix and iron doping content influence the fluorescence intensity of composite due to their effects on recombination probability of hole-electron pairs. Compared with TiO₂, 0.3% Fe-TiO₂, TiO₂/AC, 0.5% Fe-TiO₂/AC and 0.1% Fe-TiO₂/AC, the 0.3% Fe-TiO₂/AC shows the highest photoactivity with the complete mineralization of K2G for finite time due to the optimum Fe ions content and AC matrix. Furthermore, the kinetic constant (k = 0.0229 min⁻¹) of 0.3% Fe-TiO₂/AC composite is more than the sum of both TiO₂/AC (0.0154 min⁻¹) and 0.3% Fe-TiO₂ (0.0057 min⁻¹) because coexistence of the AC and Fe ions has an enlarging effect on improving the photoactivity of TiO₂. Supported by the Education Department Foundation of Hunan Province (Grant No. 08B063) and Science and Natural Science Foundation of Hunan Province (Grant No. 09JJ6101)     

Titanium dioxide nanotube fiber using in headspace solid-phase microextraction with GC–MS for BTEX detection

Anodized TiO₂ nanotube fibers using in-headspace solid-phase microextraction (SPME) with gas chromatography–mass spectrometry (GC–MS) have been exploited as an analytical method for volatile organic compounds such as benzene, toluene, ethylbenzene, and xylenes (BTEX) detection. The factors of anodizing time and annealing temperature for TiO₂ nanotube production are studied and the adsorption factors (time, ionic strength, and temperature) and desorption factors (time and temperature) for BTEX analysis are optimized. The limit of detections (LODs) for benzene, toluene, ethylbenzene o-xylene, and m, p-xylene are 0.5, 0.1, 1.0, 1.0, and 2.0 μg L⁻¹, respectively. The linear ranges for BTEX (0.5–15,000 μg L⁻¹) and satisfactory linearity (R² ≥ 0.9954) are obtained. This method is successfully applied in real samples with the recoveries ranging from 92% to 97%. TiO₂ nanotube fiber is a promising technique for BTEX analysis.     

Photocatalytic activity of polyaniline/Fe-doped TiO2 composites by in situ polymerization method

This study was focused on the photocatalytic activity of polyaniline (Pani)/iron doped titanium dioxide (Fe–TiO₂) composites for the degradation of methylene blue as a model dye. TiO₂ nanoparticles were doped with iron ions (Fe) using the wet impregnation method and the doped nanoparticles were further combined with Pani via an in situ polymerization method. For comparison purposes, Pani composites were also synthesized in the presence undoped TiO₂. The photocatalyst and the composites were characterized by standard analytical techniques such as FTIR, XRD, SEM, EDX and UV–Vis spectroscopies. Fe–TiO₂ and its composites exhibited enhanced photocatalytic activity under ultraviolet light irradiation. Improved photocatalytic activity of Fe–TiO₂ was attributed to the dopant Fe ions hindering the recombination of the photoinduced charge carriers. Pani/Fe–TiO₂ composite with 30?wt.% of TiO₂ nanoparticles achieved 28% dye removal and the discoloration rate of methylene blue for the sample was 0.0025?min^?1. FTIR, XRD, SEM, EDX and UV–Vis spectroscopies supported the idea that Fe ions integrated into TiO₂ crystal structure and Pani composites were successfully synthesized in the presence of the photocatalyst nanoparticles. The novelty of this study was to investigate the photocatalytic activity of Pani composites, containing iron doped TiO₂ and to compare their results with that of Pani/TiO₂.     

铝板为基础的S掺杂TiO_2催化分解有毒有机气体(英文)

S-doped TiO2(S-TiO2) films were immobilized on flexible low-cost aluminum sheets(S-TiO2-AS) using a sol-gel dipping process and low post-processing temperatures. The photocatalytic degradation of toxic organic vapors using the prepared films was evaluated using a continuous-flow glass tube under visible light exposure. The surface properties of the S-TiO2-AS and TiO2-AS films were examined by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, and ultraviolet-visible spectroscopy. The photolysis of benzene, toluene, ethyl benzene, and xylene(BTEX) did not occur on the bare AS. In contrast, the photocatalytic degradation efficiencies of the target pollutants using S-TiO2-AS were higher than those obtained using reference TiO2-AS photocatalyst. In particular, the average photocatalytic degradation efficiencies of BTEX using S-TiO2-0.8-AS(S/Ti ratio = 0.8) over a 3-h process were 34%, 78%, 91%, and 94%, respectively, whereas those of TiO2-AS were 2%, 11%, 21%, and 36%, respectively. The photocatalytic decompo-sition efficiencies of BTEX under visible irradiation using S-TiO2-AS increased with increasing S/Ti ratios from 0.2 to 0.8, but decreased when the ratio further increased to 1.6. Thus, S-TiO2-AS can be prepared using optimal S/Ti ratios. The degradation of BTEX over S-TiO2-AS depended on the air flow rates and initial concentrations of the target chemical. Overall, under optimal conditions, S-TiO2-AS can be effectively applied for the purification of toxic organic vapors.     

Structure,Magnetic and Photochemical Properties of Fe–TiO<Subscript>2</Subscript> Nanoparticles Stabilized in Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Matrix

Fe–TiO₂ nanoparticles with Fe concentration from 0.24 to 5 wt % were synthesized in a Al₂O₃ matrix through multiple impregnations from organic solutions of Ti n-butoxide and Fe acetylacetonate. Microstructure, morphology and magnetic properties of the composites were studied using X-ray analysis, transmission electron microscopy, energy-dispersive analysis, Mössbauer spectroscopy and magnetic susceptibility. It was shown that the deposition of the solution with low concentration of Ti n-butoxide leads to the formation of mostly extensive Fe–TiO₂ films with a small fraction of individual Fe–TiO₂ nanoparticles. On the contrary, the increase of Ti n-butoxide concentration results in the formation of a great number of individual Fe–TiO₂ nanoparticles on Al₂O₃. The size of these particles increases from 2–3 nm to 5–8 nm with the increase of Fe content in the samples from 0.24 to 1.0 (wt %). Mössbauer spectroscopy revealed two types of magnetic ions. The first type of paramagnetic Fe³⁺ demonstrate spin–lattice relaxation properties while another one substitutes Ti⁴⁺ in the TiO₂ structure thus forming Fe–TiO₂ stabilized particles in the matrix. According to the magnetic data antiferromagnetic and ferromagnetic types of exchange spin coupling occur in Fe–TiO₂/Al₂O₃ composites. The increase of Fe concentration in the composites from 1 to 5 wt % results in the narrowing of the TiO₂ band gap from 3.2 to 2.7 eV and shifting the absorption edge in visual spectrum from 350–400 to 450–500 nm.     

Reusable thin film photocatalyst of Fe‐doped TiO2 deposited by ECR plasma

The paper presents an improved method of depositing nanocrystalline thin films of Fe‐doped TiO₂ to be used as a reusable cyclic photocatalyst for degrading the organic pollutants. The technique of electron cyclotron resonance plasma‐enhanced chemical vapor deposition was employed with titanium tetra‐isopropoxide (C₁₂H₂₈O₄Ti) and ferrocene (C₁₀H₁₀Fe) as precursors of Ti and Fe, respectively. Optical emission spectroscopy was used to identify the reactive species, to determine the electron temperature and the ion density during deposition. The films were characterized using optical absorption and photoluminescence spectra, whereas the morphological analysis was carried out with scanning electron microscopy. Strong adhesion of the deposited films with the substrate ruled out any possibility of TiO₂ particles being leached out. It was confirmed by observing the degradation rate of the same film repeatedly. Cyclic use of the film for the catalytic reactions thus makes the process much user friendly for the water treatment. Copyright © 2014 John Wiley & Sons, Ltd.     

Photodegradation of Direct Blue-199 in carpet industry wastewater using iron-doped TiO2 nanoparticles and regenerated photocatalyst

Fe-doped TiO_2, Ti_1–xFe_xO₂ (x = 0.00, 0.02, 0.04, 0.06, 0.08, and 0.10), photocatalysts have been successfully synthesized via citric acid–assisted autocombustion method. The synthesized photocatalysts were characterized using different characterization techniques, such as X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), Fourier transform infrared (FT-IR), transmission electron microscopy (TEM), energy dispersive x-ray spectroscopy (EDX), and x-ray photoelectron spectroscopy (XPS). The XRD diffraction patterns revealed that synthesized photocatalysts have the anatase phase of TiO₂. The DRS analysis indicates a slight increment in absorbance in the visible light region by the Fe doping in TiO₂. The FT-IR spectra reveal the various stretching and bending vibrational bands of the Ti–O lattice. The XPS spectra confirm the presence of elements titanium, oxygen, and iron in the synthesized samples and determine binding energy of elements. TEM analysis shows the shape of the synthesized photocatalyst, and it was used to calculate the average particle sizes of undoped and Fe-doped TiO₂ (Ti_0.96Fe_0.04O₂) photocatalysts using a histogram. The photocatalytic activities of synthesized photocatalysts were determined by photodegradation of dye (Direct Blue 199), contaminating carpet industry wastewater in the photochemical reactor and open pan reactor. The maximum photodegradation activity was shown by the Ti_0.96Fe_0.04O₂ photocatalyst among all the synthesized undoped and Fe-doped photocatalysts. The synthesized photocatalyst (Ti_0.96Fe_0.04O₂) had better photocatalytic activity when compared to both, undoped TiO₂ and Aeroxide (Degussa) P-25. The used Fe-doped TiO₂ photocatalyst (Ti_0.96Fe_0.04O₂) was regenerated five times and investigated for its photocatalytic activity.     

Electrochemical Fabrication and Properties of Highly Ordered Fe‐Doped TiO2 Nanotubes

Highly‐ordered Fe‐doped TiO₂ nanotubes (TiO₂nts) were fabricated by anodization of co‐sputtered Ti–Fe thin films in a glycerol electrolyte containing NH₄F. The as‐sputtered Ti–Fe thin films correspond to a solid solution of Ti and Fe according to X‐ray diffraction. The Fe‐doped TiO₂nts were studied in terms of composition, morphology and structure. The characterization included scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, UV/Vis spectroscopy, X‐ray photoelectron spectroscopy and Mott–Schottky analysis. As a result of the Fe doping, an indirect bandgap of 3.0 eV was estimated using Tauc’s plot, and this substantial red‐shift extends its photoresponse to visible light. From the Mott–Schottky analysis, the flat‐band potential (E_fb) and the charge carrier concentration (N_D) were determined to be ?0.95 V vs Ag/AgCl and 5.0 ×10¹⁹ cm^?3 respectively for the Fe‐doped TiO₂nts, whilst for the undoped TiO₂nts, E_fb of ?0.85 V vs Ag/AgCl and N_D of 6.5×10¹⁹ cm^?3 were obtained.