Isotopic analysis of single uranium and plutonium particles by chemical treatment and mass spectrometry

The isotopic composition of single uranium and plutonium particles was measured with an inductively coupled plasma mass spectrometer (ICP-MS) and a thermal ionization mass spectrometer (TIMS). Particles deposited on a carbon planchet were first analyzed with an energy dispersive X-ray spectrometer (EDX) attached to a scanning electron microscope (SEM) and then transferred on to a silicon wafer using a manipulator. The particle on the silicon wafer was dissolved with nitric acid and the isotopic ratios of U and Pu were measured with ICP-MS and TIMS. The results obtained by both methods for particles of certified reference materials showed good agreement with the certified values within the expected uncertainty. The measurement uncertainties obtained in this study were similar for both mass spectrometric methods. This study was performed to establish the method of particle analysis with SEM, EDX, the particle manipulation and chemical preparation technique, and the measurement of isotopic ratios of U and Pu in a single particle by mass spectrometry.     

Round robin for uranium isotopic measurements by mass spectrometry

A round-robin for uranium isotopic analysis in two solutions with different concentrations prepared and certified by the Institute for Reference Materials and Measurements (IRMM, Geel, Belgium) was organized by CETAMA, a division of the Commissariat à l’énergie Atomique (CEA: French Atomic Energy Commission Fourteen laboratories took part in the program using twenty-five different instruments (ICP-QMS, ICP-SFMS and TIMS). For each solution and each isotopic ratio, a statistical analysis based on standard ISO 5725 was carried out to calculate the mean, the repeatability and reproducibility standard deviations, the z-score and zeta-score, the bias with respect to the target values, and to compare their precision. The mean measurement results for the ²³⁴U/²³⁸U and ²³⁵U/²³⁸U isotopic ratios show no significant biases compared with the target values, whatever is the analytical technique. The results were much less satisfactory for the ²³⁶U/²³⁸U isotopic ratio, for which only the laboratories specialized in traces analyses and/or precise isotopic analyses submitted results in good agreement with the target values. A detailed discussion is given in this article.     

同位素稀释热电离质谱法测定人血清中痕量铜和锌

采用热电离同位素稀释质谱法(ID-TIMS)准确测定了欧盟标准物质与测量研究院(EC-JRC-IRMM)组织的国际测量评估计划IMEP-17人血清样品中的痕量铜和锌。由于锌和铜都是易受污染的元素,本工作建立了仅用少量硝酸消解的低流程本底和适于热电离质谱测量的生物基体血清中痕量铜和锌的样品前处理方法;采用适当比例的硅胶和磷酸作为电离增强剂,在热电离质谱(TIMS)测量时获得了较高强度且稳定的铜和锌离子束;血清中痕量铜和锌的测量结果可直接溯源到国际单位mole。2种人血清样品中铜和锌测量结果的不确定度(k=2)分别为0.94%、0.83%和0.49%,测量值被EC-JRC-IRMM采用作为该样品的标准值。     

Application of laser ablation inductively coupled plasma mass spectrometry for the isotopic analysis of single uranium particles

The paper describes the application of laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) for the isotopic analysis of individual uranium-oxide particles. The procedure developed is suitable for the accurate measurement of ²³⁴U, ²³⁵U, ²³⁶U and ²³⁸U isotopes in single actinide particles with lateral dimensions down to 10 μm. The ²³⁵U/²³⁸U isotope ratios can be obtained with a precision of a few percent relative standard deviation using a single collector ICP-MS instrument. The precision could be improved by the use of slow ablation and by taking several LA-ICP-MS replicate spectra on the same particle investigated. For the minor isotopes use of higher mass resolution (R = 4000) was necessary in some cases to avoid spectral interferences. The technique developed offers a rapid and accurate possibility for the isotopic composition determination of uranium-containing individual particles in environmental and safeguards samples.     

Development of an improved method to perform single particle analysis by TIMS for nuclear safeguards

A method is described that allows measuring the isotopic composition of small uranium oxide particles (less than 1 μm in diameter) for nuclear safeguards purposes. In support to the development of reliable tools for the identification of uranium and plutonium signatures in trace amounts of nuclear materials, improvements in scanning electron microscopy (SEM) and thermal ionization mass spectrometry (TIMS) in combination with filament carburization and multiple ion counting (MIC) detection were investigated. The method that has been set up enables the analysis of single particles by a combination of analytical tools, thus yielding morphological, elemental and isotopic information. Hereby individual particles of certified reference materials (CRMs) containing uranium at femtogram levels were analysed. The results showed that the combination of techniques proposed in this work is suitable for the accurate determination of uranium isotope ratios in single particles with improved capabilities for the minor abundant isotopes.     

Characterization of uranium particles produced by hydrolysis of UF6 using SEM and SIMS.

Environmental sampling (ES) is a powerful technique used by safeguards inspectors of the International Atomic Energy Agency and the European Safeguards Office for the detection of undeclared nuclear activities. Since its implementation in the 1990s, ES has proven to be very sensitive and effective. Considering the consequences, the measurements should be carried out under a quality management programme. At the Institute for Reference Materials and Measurements, a new production method is under development for the preparation of reference uranium particles from well-certified UF6, allowing uranium particles with certified isotopic abundances to be prepared that are representative of those found in uranium enrichment facilities. Using an aerosol deposition chamber designed and built for the purpose, particles are formed by the hydrolysis of UF6 and their morphology and (isotopic) composition measured using SEM-EDX and SIMS. The SEM measurements show that by varying the relative humidity of the air in the reaction chamber, the morphology of the particles can be changed. By making a distribution map of the chemical composition of the particles, the relationship between fluorine and uranium as main constituents of the particle could be established. The presence of fluorine is a valuable indicator for the occurrence of nondeclared enrichment activities.     

A novel isotope analysis of oxygen in uranium oxides: comparison of secondary ion mass spectrometry,glow discharge mass spectrometry and thermal ionization mass spectrometry

The natural variation of the oxygen isotopic composition is used among geologists to determine paleotemperatures and the origin of minerals. In recent studies, oxygen isotopic composition has been recognized as a possible tool for identification of the origin of seized uranium oxides in nuclear forensic science. In the last 10 years, great effort has been made to develop new direct and accurate n(¹⁸O)/n(¹⁶O) measurements methods. Traditionally, n(¹⁸O)/n(¹⁶O) analyses are performed by gas mass spectrometry. In this work, a novel oxygen isotope analysis by thermal ionization mass spectrometry (TIMS), using metal oxide ion species (UO⁺), is compared to the direct methods: glow discharge mass spectrometry (GDMS) and secondary ion mass spectrometry (SIMS). Because of the possible application of the n(¹⁸O)/n(¹⁶O) ratio in nuclear forensics science, the samples were solid, pure UO₂ or U₃O₈ particles. The precision achieved using TIMS analysis was 0.04%, which is similar or even better than the one obtained using the SIMS technique (0.05%), and clearly better if compared to that of GDMS (0.5%). The samples used by TIMS are micrograms in size. The suitability of TIMS as a n(¹⁸O)/n(¹⁶O) measurement method is verified by SIMS measurements. In addition, TIMS results have been confirmed by characterizing the n(¹⁸O)/n(¹⁶O) ratio of UO₂ sample also by the traditional method of static vacuum mass spectrometry at the University of Chicago.     

Isotopic analysis of metallic and coated microparticles by laser ablation time-of-flight mass spectrometry (LA-TOF-MS)

A laser ablation time of flight mass spectrometry (LA-TOF-MS) technique was applied to the isotopic analysis of variety of microparticles. Sample with only two Gd₂O₃ particles with ~ 10 μm in diameter, the mixed particles composed of Gd₂O₃, Ni, and Pd, and silica particles coated with few tens of ng of Gd have been analyzed. The ablation of particles was achieved by a second harmonic of a Nd:YAG laser, 532 nm with loading these particles onto various metal matrices such as Ta, Zn, and Cu. Isotopic analysis for adopted sample was successfully carried out with good mass resolution. The loaded two small sized particles (~ 10 μm) were analyzed with reasonable isotopic ratios for enough time to observe the ion signal by the 10 Hz laser. In the case of coated particle, isotopic abundances of Gd (~ 50 ng/particle) were observed and the measured isotopic ratio reasonably agreed to the natural abundance of Gd. As far as the sample loading plates (matrix) are concerned, Ta and Cu plates showed more improved detection sensitivity and mass resolution. Direct analysis of swiped-mixed metal particles onto the cotton textile shows the possibility for an application of environmental sample analysis in nuclear safeguards.     

An inter-calibration campaign using various selected Pu spike isotopic reference materials

In nuclear safeguards, precise and accurate isotopic analyses are needed for two major elements from the nuclear fuel cycle: uranium and plutonium. This can be achieved by Isotope Dilution Mass Spectrometry (IDMS), which is one of the most reliable analytical techniques for the determination of plutonium amount content to a high level of accuracy. In order to achieve reliable isotope measurements isotopic reference materials with certified amount of plutonium and isotopic composition are required. At the Institute for Reference Materials and Measurements (IRMM) various plutonium spike reference materials for isotopes ²³⁹Pu, ²⁴⁰Pu, ²⁴²Pu and ²⁴⁴Pu are available. This enabled the setup of an inter-calibration campaign inter-linking selected plutonium spikes on a metrological basis applying state-of-the-art measurement procedures. The aim of this campaign is threefold: firstly to perform measurements on selected plutonium spike isotopic reference materials for quality control purposes, secondly to verify the amount content and the isotopic composition of the recently produced IRMM-1027m large sized dried (LSD) spikes and thirdly to demonstrate IRMM’s measurement capabilities for plutonium analysis via external quality tools. The obtained results using various spike isotopic reference materials will be presented and discussed in this paper. The measurement uncertainties of the IDMS results were calculated according to the guide to the expression of uncertainty in measurement (GUM).     

Comparison of ICP-MS and SIMS techniques for determining uranium isotope ratios in individual particles

The determination of uranium isotope ratios in individual particles is of great importance for nuclear safeguards. In the present study, an analytical technique by inductively coupled plasma mass spectrometry (ICP-MS) with a desolvation sample introduction system was applied to isotope ratio analysis of individual uranium particles. In ICP-MS analysis of individual uranium particles with diameters ranging from 0.6 to 4.2 μm in a standard reference material (NBL CRM U050), the use of the desolvation system for sample introduction improved the precision of ²³⁴U/²³⁸U and ²³⁶U/²³⁸U isotope ratios. The performance of ICP-MS with desolvation was compared with that of a conventionally used method, i.e., secondary ion mass spectrometry (SIMS). The analysis of test swipe samples taken at nuclear facilities implied that the performance of ICP-MS with desolvation was superior to that of SIMS in a viewpoint of accuracy, because the problems of agglomeration of uranium particles and molecular ion interferences by other elements could be avoided. These results indicated that ICP-MS with desolvation has an enough ability to become an effective tool for nuclear safeguards.     

Performance of laser ablation: quadrupole-based ICP-MS coupling for the analysis of single micrometric uranium particles

In this paper we describe the application of laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) coupling to particle analysis, i.e., the determination of the isotopic composition of micrometric uranium particles. The performances of this analysis technique are compared with those of the two reference particle analysis techniques: secondary ion mass spectrometry (SIMS) and fission track-thermo-ionization mass spectrometry (FT-TIMS), based on the measurement of the isotopic ratios of ²³⁵U/²³⁸U in particles present in an inter-comparison particulate sample. The agreement of the results obtained using LA-ICP-MS with target values and with the results obtained using FT-TIMS and SIMS was good. Accuracy was equivalent to that of the other two techniques (±3 % deviation). However, relative experimental uncertainties present with LA-ICP-MS (7 %) were higher than those present with FT-TIMS (4.5 %) and SIMS (3 %). Furthermore, measurement yield of LA-ICP-MS coupling was close to that obtained with the same quadrupole ICP-MS for the measurement of a liquid sample (~10^?4), but lower than that obtained with FT-TIMS and SIMS, respectively, by a factor of 10 and 20, although the particles analyzed using LA-ICP-MS were most likely smaller (diameter ~0.6 μm, containing 4–7 fg of ²³⁵U). Nevertheless, thanks to the brevity of the signals obtained, the detection capacity for low isotopic concentrations by LA-ICP-MS coupling is equivalent to that of FT-TIMS, although it remains well below that of SIMS (×15). However, with more sensitive double focusing ICP-MS, performances equivalent to those achieved using SIMS could be obtained.     

Determination of ultratrace boron concentrations in uranium oxide by isotope dilution-thermal ionization mass spectrometry using a simplified separation procedure

Boron was determined at sub-ppm levels in uranium oxide by ID-TIMS. Following nitric acid dissolution, a solvent extraction method was adapted for extraction of boron by 5% 2-ethylhexane-1,3-diol in chloroform followed by evaporation of the extractant in presence of sodium carbonate and mannitol. This procedure allowed TIMS analysis of boron by monitoring the Na₂BO ₂ ⁺ ions formed from the sodium borate salt in the ion source. Reproducibility of about 1% was obtained for boron determination in the three different uranium oxide samples containing sub-ppm amounts of boron.     

Isotopic abundance measurements on solid nuclear-type samples by glow discharge mass spectrometry

A double-focusing Glow Discharge Mass Spectrometer (GDMS) installed in a glovebox for nuclear sample screening has been employed for isotopic measurements. Isotopic compositions of zirconium, silicon, lithium, boron, uranium and plutonium which are elements of nuclear concern have been determined. Interferences arising from the matrix sample and the discharge gas (Ar) for each of these elements are discussed. The GDMS results are compared with those from Thermal Ionization Mass Spectrometry (TIMS). For boron and lithium at microg/g-ng/g levels, the two methods gave results in good agreement. In samples containing uranium the isotopic composition obtained by GDMS was in agreement with those from TIMS independently of the enrichment. Attempts for the determination of plutonium isotopic composition were also made. In this case, due to the interferences of uranium at mass 238 and americium at mass 241, the GDMS raw data are complementary with those values obtained from physical non-destructive techniques.     

Comparison of AMS,TIMS, and SIMS techniques for determining uranium isotope ratios in individual particles

The determination of isotope ratios in individual uranium particles is very important for nuclear safeguards. In this work, accelerator mass spectrometry (AMS), thermal ionization mass spectrometry (TIMS), and secondary ion mass spectrometry (SIMS) were applied to isotope ratio analysis of individual uranium particles and compared in terms of background, measurement accuracy, and efficiency. Several individual uranium particles (1–7 μm) from certified reference materials were used as samples. The results show that the average values of blank counting rate of ²³⁵U for AMS, FT-TIMS (FT: fission track), SEM-TIMS (SEM: scanning electron microscope), and SIMS were 7.3, 7.8, 2.7 and 2.2 cps, respectively. The relative error of ²³⁴U/²³⁵U and ²³⁴U/²³⁶U isotope ratios of the particles from U200 for AMS were within 10% and 20%, whereas the results of FT-TIMS and SIMS were within 5% and 10%, respectively. The relative error and external precision of ²³⁴U/²³⁸U and ²³⁵U/²³⁸U of the particles from U850 for the method of AMS, SEM-TIMS, and SIMS were within 10% and 5%, respectively. For ²³⁶U/²³⁸U, the average values of the relative error and external precision measured by AMS were within 5%, which measured by SEM-TIMS and SIMS were all within 10%. AMS has advantages in measuring ²³⁶U/²³⁸U. The measurement time of AMS and SEM-TIMS was shorter than that of FT-TIMS and longer than that of SIMS. It is considered that AMS and SEM-TIMS have a certain development prospect, and it is necessary to research deeply.     

Isotopic abundance measurements on solid nuclear-type samples by glow discharge mass spectrometry

A double-focusing Glow Discharge Mass Spectrometer (GDMS) installed in a glovebox for nuclear sample screening has been employed for isotopic measurements. Isotopic compositions of zirconium, silicon, lithium, boron, uranium and plutonium which are elements of nuclear concern have been determined. Interferences arising from the matrix sample and the discharge gas (Ar) for each of these elements are discussed. The GDMS results are compared with those from Thermal Ionization Mass Spectrometry (TIMS). For boron and lithium at g/g-ng/g levels, the two methods gave results in good agreement. In samples containing uranium the isotopic composition obtained by GDMS was in agreement with those from TIMS independently of the enrichment. Attempts for the determination of plutonium isotopic composition were also made. In this case, due to the interferences of uranium at mass 238 and americium at mass 241, the GDMS raw data are complementary with those values obtained from physical non-destructive techniques.     

Development in fission track-thermal ionization mass spectrometry for particle analysis of safeguards environmental samples

An improved method of fission track (FT) sample preparation was developed, in which the detector of fission track and the layer containing particles are separated, in order to apply the FT-thermal ionization mass spectrometry (TIMS) for particle analysis of safeguards environmental samples. The developed FT sample enabled us to detect the particle of interest simply by observing the fission tracks. The process of particle identification was difficult due to the discrepancy between the position of the particles and fission tracks, which were observed in the conventional FT sample. The proposed method has significantly resolved this problem.     

Application of Inductively Coupled Plasma Mass Spectrometry to the determination of uranium isotope ratios in individual particles for nuclear safeguards

The capability of inductively coupled plasma mass spectrometry (ICP-MS) for the determination of uranium isotope ratios in individual particles was determined. For this purpose, we developed an experimental procedure including single particle transfer with a manipulator, chemical dissolution and isotope ratio analysis, and applied to the analysis of individual uranium particles in certified reference materials (NBL CRM U050 and U350). As the result, the ²³⁵U/²³⁸U isotope ratio for the particle with the diameter between 0.5 and 3.9 μm was successfully determined with the deviation from the certified ratio within 1.8%. The relative standard deviation (R.S.D.) of the ²³⁵U/²³⁸U isotope ratio was within 4.2%. Although the analysis of ²³⁴U/²³⁸U and ²³⁶U/²³⁸U isotope ratios gave the results with inferior precision, the R.S.D. within 20% was possible for the measurement of the particle with the diameter more than 2.1 μm. The developed procedure was successfully applied to the analysis of a simulated environmental sample prepared from a mixture of indoor dust (NIST SRM 2583) and uranium particles (NBL CRM U050, U350 and U950a). From the results, the proposed procedure was found to be an alternative analytical tool for nuclear safeguards.     

Polyaniline-functionalized porous adsorbent for Sr2+ adsorption

To support the nuclear safeguards particle analysis, a method was developed to produce micrometer-sized uranium oxide microspheres with a known uranium content and isotope ratio, which are intended to be characterized as certified reference material. To simplify handling of the produced particles, the collected particles have been transferred into ethanol suspensions. In addition to a demonstration of the suitability and new capabilities of such particle suspensions, such as the preparation of particle mixtures, the stability of the particles has been investigated and demonstrated with regard to dissolution and isotopic exchange.     

Combined application of alpha-track and fission-track techniques for detection of plutonium particles in environmental samples prior to isotopic measurement using thermo-ionization mass spectrometry

The fission track technique is a sensitive detection method for particles which contain radio-nuclides like ²³⁵U or ²³⁹Pu. However, when the sample is a mixture of plutonium and uranium, discrimination between uranium particles and plutonium particles is difficult using this technique. In this study, we developed a method for detecting plutonium particles in a sample mixture of plutonium and uranium particles using alpha track and fission track techniques. The specific radioactivity (Bq/g) for alpha decay of plutonium is several orders of magnitude higher than that of uranium, indicating that the formation of the alpha track due to alpha decay of uranium can be disregarded under suitable conditions. While alpha tracks in addition to fission tracks were detected in a plutonium particle, only fission tracks were detected in a uranium particle, thereby making the alpha tracks an indicator for detecting particles containing plutonium. In addition, it was confirmed that there is a linear relationship between the numbers of alpha tracks produced by plutonium particles made of plutonium certified standard material and the ion intensities of the various plutonium isotopes measured by thermo-ionization mass spectrometry. Using this correlation, the accuracy in isotope ratios, signal intensity and measurement errors is presumable from the number of alpha tracks prior to the isotope ratio measurements by thermal ionization mass spectrometry. It is expected that this method will become an effective tool for plutonium particle analysis. The particles used in this study had sizes between 0.3 and 2.0 μm.     

New methodology for uranium analysis in swipe samples for nuclear safeguards purposes

Environmental swipe sampling for safeguards purpose has been used by International Atomic Energy Agency since 1997, being a powerful tool to detect undeclared materials and activities. This work describes a new methodology for swipe samples analysis based on ultrasound-assisted acid leaching and compares it with traditional total digestion bulk analysis. The proposed method requires few preparation steps, decreasing the risk of contamination, reduced amounts of reagents and a good option to extract uranium from swipe sample. In a real case study, the swipe samples were collected in a conversion plant at IPEN/CNEN, Brazil. The measurements were carried out by ICP-MS and the results showed relative error lower than 0.96 % for uranium isotopic ratios for the certified reference material (NBS U200). The uncertainties were estimated by following the ISO GUM, with a confidence level of 95 %. The uncertainties percentage for n(²³⁵U)/n(²³⁸U) ratio of the samples ranged from 2.5 to 4.3 %. The values of uranium isotopic ratio obtained for each method demonstrate the viability of using the methodology proposed in this work.