LLE for (water + ionic liquid) binary systems using [Cxmim][BF4] (x = 6, 8) ionic liquids

Liquid–liquid equilibrium diagrams were determined for (IL + water) systems using the family of ILs 1-alkyl-3-methylimidazolium tetrafluoroborates, where the alkyl groups are hexyl and octyl ([C_xmim][BF₄] with x = 6 and 8). The gravimetric method was used to determine the equilibrium compositions at temperatures ranging from 278.15 to 340.15 K. Both systems present an upper critical solution temperature (UCST), which increases from [C₆mim][BF₄] to [C₈mim][BF₄]. The experimental data were correlated using the NRTL and eNRTL models. The binary interaction parameters were calculated for each system and model, and good agreement between experimental and calculated equilibrium compositions was obtained. Finally, the apparent Gibbs energy, enthalpy and entropy of water solution in the ILs were calculated using a modified van’t Hoff equation. The three thermodynamic functions were found to be positive for both ILs.     

离子液体型表面活性剂研究

以1-甲基咪唑为原料, 制备了6个常规离子液体: 1-正丁基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[bmim][BF₄]及[bmim][PF₆])、1-正己基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[hmim][BF₄]及[hmim][PF₆])、1-正十六烷基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[C₁₆mim][BF₄]及[C₁₆mim][PF₆])和4个功能化离子液体: 1-(2-羟乙基)-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[2-hemim][BF₄]及[2-hemim][PF₆])、1-乙氧羰基甲基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[eocmmim][BF₄]及[eocmmim][PF₆]). 研究了这两类离子液体的一些物理性能, 旨在挖掘离子液体在香料香精化妆品工业中的应用价值. 分别检测了它们与一般溶剂的互溶性, 并测定了它们的表面张力和发泡性能, 实验结果表明, 仅[C₁₆mim][BF₄]和[C₁₆mim][PF₆]具有发泡性能, 发泡力分别为68和120 mm.     

Phase equilibria of imidazolium ionic liquids and the refrigerant gas, 1,1,1,2-tetrafluoroethane (R-134a)

A number of applications with ionic liquids (ILs) and hydrofluorocarbon gases have recently been proposed. Detailed phase equilibria and modeling are needed for their further development. In this work, vapor–liquid equilibrium, vapor–liquid–liquid equilibrium, and mixture critical points of imidazolium ionic liquids with the hydrofluorocarbon refrigerant gas, 1,1,1,2-tetrafluoroethane (R-134a) was measured at temperatures of 25 °C, 50 °C, 75 °C and pressure up to 143 bar. The ionic liquids include 1-hexyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)amide ([HMIm][Tf₂N]), 1-hexyl-3-methyl-imidazolium hexafluorophosphate ([HMIm][PF₆]), and 1-hexyl-3-methyl-imidazolium tetrafluoroborate ([HMIm][BF₄]). The effects of the anion and cation on the solubility were investigated with the anion having greatest impact. [HMIm][Tf₂N] demonstrated the highest solubility of R-134a. The volume expansion and molar volume were also measured for the ILs and R-134a. The Peng–Robinson Equation of State with van der Waals 2-parameter mixing rule with estimated IL critical points were employed to model and correlate the experimental data. The models predict the vapor–liquid equilibrium and vapor–liquid–liquid equilibrium pressure very well. However, the mixture critical points predictions are consistently lower than experimental values.     

Densities and viscosities for ionic liquids mixtures containing [eOHmim][BF4], [bmim][BF4] and [bpy][BF4]

Densities and viscosities of binary ionic liquids mixtures, 1-(2-hydroxyethyl)-3-methylimidazolium tetrafluoroborate ([eOHmim][BF₄]) + 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), 1-(2-hydroxyethyl)-3-methylimidazolium tetrafluoroborate ([eOHmim][BF₄]) + N-butylpyridinium tetrafluoroborate ([bpy][BF₄]) and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]) + N-butylpyridinium tetrafluoroborate ([bpy][BF₄]) were measured over the entire mole fraction from T = (298.15 to 343.15) K. The excess molar volumes were calculated and correlated by Redlich–Kiser polynomial expansions. The viscosities for pure ionic liquids were analyzed by means of the Vogel–Tammann–Fulcher equation and ideal mixing rules were applied for the ILs mixtures.     

Solubility of CO2 in imidazolium-based tetrafluoroborate ionic liquids

The solubility of CO₂ in imidazolium ionic liquids (ILs), 1-butyl-3-methyl imidazolium tetrafluoroborate ([bmim][BF₄]), 1-hexyl-3-methyl imidazolium tetrafluoroborate ([hmim][BF₄]) and 1-octyl-3-methyl imidazolium tetrtafluoroborate ([omim][BF₄]) was determined at 305-25 K and pressures from 1 to 9 MPa. The influence of chain length of alkyl substituents on the imidazolium cation on the solubility of CO₂ was investigated. The differences in solubility with chain length are in the sequence [omim][BF₄] > [hmim][BF₄] > [bmim][BF₄]. The solubility data were correlated by the extended Henry's law, and enthalpy, Gibbs free energy and entropy changes were obtained.     

Kinetic study of the oxidative addition of methyl iodide to Vaska’s complex in ionic liquids

Oxidative addition of methyl iodide to Vaska’s complex in the ionic liquids 1-butyl-3-methylimidazolium triflate [C₄mim][OTf], [C₄mim] bis(trifluormethylsulfonyl)imide [Tf₂N], and N-hexylpyridinium [C₆pyr][Tf₂N] occurred cleanly to give the expected Ir(III) oxidative addition product. Pseudo-first order rate constants were determined for the oxidative addition reaction in each solvent ([Vaska’s] = 0.25 mM, [CH₃I] = 37.5 mM). The observed rate constants under these conditions were 5-10 times slower than the rate seen in DMF. At high methyl iodide concentrations (>23 mM), the expected first order dependence on methyl iodide was not observed. In each ionic liquid, there was no change in the reaction rates within experimental error over the methyl iodide concentration range of 23-75 mM. At lower methyl iodide concentration, a decrease in rate was observed in [C₄mim][Tf₂N] with decreasing concentration of methyl iodide.     

The physicochemical properties of some imidazolium-based ionic liquids and their binary mixtures

The density, viscosity and conductivity of ionic liquids (ILs), 1-octyl-3-methylimidazolium tetrafluoroborate ([omim][BF4]), 1-octyl-3-methylimidazolium chloride ([omim][Cl]), 1-hexyl-3-methylimidazolium tetrafluoroborate ([hmim] BF4]), 1-hexyl- 3-methylimidazolium chloride ([hmim][Cl]), 1-hexyl-3-methylimidazolium hexafluorophosphate ([hmim][PF6]), and the [omim][BF4] + [omim][Cl], [hmim][BF4] + [hmim][Cl], and [hmim][PF6] + [hmim][Cl] binary mixtures were studied at dif- ferent temperatures. It was demonstrated that the densities of both the neat ILs and their mixtures varied linearly with temper- ature. The density sensitivity of a binary mixture is between those of the two components. The excess molar volumes (VE) of [hmim][BF4] + [hmim][Cl] and [hmim][PF6] + [hmim][Cl] mixtures are positive in the whole composition range. For [omim][BF4] + [omim][Cl], the VE is also positive in the [omim][Cl]-rich region, but is negative in the [omim][BF4]-rich re- gion. The viscosity or conductivity of a mixture is in the intermediate of those of the two neat ILs. For all the neat ILs and the binary mixtures studied, the order of conductivity is opposite to that of the viscosity. The Vogel-Tammann-Fulcher (VTF) equations can be used to fit the viscosity and conductivity of all the neat ILs and the binary mixtures. The neat ILs and their mixtures obey the Fractional Walden Rule very well, and the values of the Walden slopes are all smaller than unit, indicating obvious ion associations in the neat ILs and the binary mixtures.     

Ionic Liquid-Induced Structural and Activity Changes in Hen Egg White Lysozyme

Lysozyme crystals in the presence of 1-butyl-3-methylimidazolium tetrafluoroborate ([C₄mim]BF₄), 1-butyl-3-methylimidazolium chloride ([C₄mim]Cl), 1-butyl-3-methylimidazolium bromide([C₄mim]Br), and 1,3-dimethylimidazolium iodine([dmim]I) were prepared, and the influence of ionic liquids (ILs) on the structure and activity change of lysozyme was investigated. Fourier transform infrared spectroscopy revealed the major secondary structures of α-helix and β-sheet for lysozyme. It was interesting to note that increases of the band near 2,935 and 1,656 cm^?1 from Raman spectroscopy are attributed to the unfolding of lysozyme molecules. A shift in amide III from 1,230 to 1,270 cm^?1 in adding [dmim]I occurs, indicating a transformation from β-sheet to random coil. With regard to adding [C₄mim]BF₄, [C₄mim]Cl, and [C₄mim]Br, α-helix and β-sheet are the predominant structures for lysozyme. The activity study showed that the ILs used brought a positive effect. Especially, [dmim]I leads to a drastic increase in relative activity, and its value reaches 50 %.     

Study of the behaviour of the azeotropic mixture ethanol–water with imidazolium-based ionic liquids

In this work, experimental data of isobaric vapour–liquid equilibria for the ternary system ethanol + water + 1-hexyl-3-methylimidazolium chloride ([C₆mim][Cl]) and for the corresponding binary systems containing the ionic liquid (ethanol + [C₆mim][Cl], water + [C₆mim][Cl]) were carried out at 101.300 kPa. VLE experimental data of binary and ternary systems were correlated using the NRTL equation. In a previous work [N. Calvar, B. González, E. Gómez, A. Domínguez, J. Chem. Eng. Data 51 (2006) 2178–2181], the VLE of the ternary system ethanol + water + [C₄mim][Cl] was determined and correlated, so we can study the influence of different ionic liquids in the behaviour of the azeotropic mixture ethanol–water.     

Solubility of H2S in 1-(2-hydroxyethyl)-3-methylimidazolium ionic liquids with different anions

The solubility of hydrogen sulfide in a series of 1-(2-hydroxyethyl)-3-methylimidazolium ([HOemim]⁺)-based ionic liquids (ILs) containing different anions, viz. hexafluorophosphate ([PF₆]⁻), trifluoromethanesulfonate ([OTf]⁻), and bis-(trifluoromethyl)sulfonylimide ([Tf₂N]⁻) at temperatures ranging from 303.15 to 353.15 K and pressures of up to about 1.8 MPa was measured by a volumetric based static apparatus. The solubility data were correlated using two models: (1) the Krichevsky–Kasarnovsky equation and (2) the extended Henry's law combined with the Pitzer's virial expansion for the excess Gibbs energy. Henry's law constants (at zero pressure) in mole-fraction and molality scales were obtained at different temperatures by means of these two models. Using the solubility data, the partial molar thermodynamic functions of solution, i.e. Gibbs energy, enthalpy, and entropy were calculated. Comparison showed that the solubility of H₂S is greater than that of CO₂ in the corresponding ILs studied in this work and that the solubility of both gases increases as the number of trifluoromethyl (–CF₃) groups in the anion increases, i.e. the solubility behavior of both gases follows the order [HOemim][Tf₂N] ≥ [HOemim][OTf] > [HOemim][PF₆] > [HOemim][BF₄].     

Effect of imidazolium-based ionic liquids on the aggregation behavior of twin-tailed cationic gemini surfactant in aqueous solution

Micellization behavior of the twin-tailed surfactants can be modulated by the addition of various modifiers. Ionic liquids (ILs) are one of them and are documented here. The beauty of these environmentally benign neoteric molecules lies in their structural versatility. Here, we have investigated the effect of three ILs: 1-butyl-3-methylimidazolium bromide ([C₄mim][Br]), 1-hexyl-3-methylimidazolium bromide ([C₆mim][Br]), and 1-octyl-3-methylimidazolium bromide ([C₈mim][Br]) on the aggregation and surface adsorption behavior of cationic gemini surfactant, bis(hexadecyldimethyl ammonium)propane dibromide (16-3-16) through experimentally measured electrical conductivities, surface tensions, and by spectral methods (UV-vis absorbance and fluorescence measurements). The main focus of the study is to observe the effect of added ILs on the critical micelle concentration (cmc), various surface parameters, aggregation number, and size of the aggregates of gemini surfactant. The results show that the more hydrophobic ILs, that is, [C₆mim][Br] and [C₈mim][Br] behave as electrolyte at lower concentration and cosurfactant at higher concentration, whereas moderately hydrophobic IL [C₄mim][Br] acts as an electrolyte at all concentration ranges studied. The modulating effects of ILs were also compared with conventional electrolyte (NaBr) at similar conditions.     

Temperature dependence of the microstructure of 1-butyl-3-methylimidazolium tetrafluoroborate in aqueous solution

Many applications of ionic liquids (ILs) are closely related with their microstructure in mixtures. For example, morphology and pore size of the MCM-41 prepared in aqueous ILs are greatly dependent on the aggregation behavior of the ILs in water. Therefore, the study on the microstructure of ILs in aqueous solutions is of great importance. In this work, ¹H NMR, dynamic light scattering and attenuated total reflection infrared spectroscopy have been used to investigate the temperature effect on the structures of aqueous 1-butyl-3-methylimidazolium tetrafluoroborate ([C₄mim][BF₄]) solutions. It was shown that the size of the IL aggregates becomes larger with decreasing temperature. When the system temperature is below the upper critical solution temperature (UCST) of the binary mixture at about 4 °C, the aggregate size of the IL is larger than 1000 nm. Additionally, the two-dimensional IR results reveal that at low IL concentrations, H₂O can interact with [BF₄]⁻ prior to the CH groups of the imidazolium ring, whereas cation and anion of the IL tend to form aggregate at high IL concentrations. With the decrease of temperature, the interactions between cation and anion of the IL become stronger, but those between the IL and water become weaker, thereby resulting in the growth of the aggregate of cation with anion of the IL. This result may give a reasonable explanation for the origin of the UCST behavior of aqueous [C₄mim][BF₄] solution.     

Ionic liquids extraction of Para Red and Sudan dyes from chilli powder, chilli oil and food additive combined with high performance liquid chromatography

A simple analytical method, based on the coupling of ionic liquid-based extraction with high performance liquid chromatography (HPLC), is developed for the determination of Sudan dyes (I, II, III and IV) and Para Red in chilli powder, chilli oil and food additive samples. Two ionic liquids (ILs), 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄mim][PF₆]) and 1-octyl-3-methylimidazolium hexafluorophosphate ([C₈mim][PF₆]), were compared as extraction solvents; experiments indicated that the latter possesses higher recoveries for each analyte. Parameters related to extraction of Sudan dyes and Para Red were also optimized. Under the optimal conditions, good reproducibility of extraction performance was obtained, with the relative standard deviation (RSD) values ranging from 2.0% to 3.5%. The detection limits of Sudan dyes and Para Red (LOD, S/N = 3) were in the range of 7.0-8.2 μg kg⁻¹ for chilli powder and 11.2-13.2 μg L⁻¹ for chilli oil and food additive. The recoveries were in the range of 76.8-109.5% for chilli powder samples and 70.7-107.8% for chilli oil and food additive samples.     

Extraction and high performance liquid chromatographic determination of 3-indole butyric acid in pea plants by using imidazolium-based ionic liquids as extractant

In this paper, imidazolium-based ionic liquids [C₄mim][PF₆], [C₆mim][PF₆], [C₈mim][PF₆], [C₆mim][BF₄] and [C₈mim][BF₄] were tested as extracting solvents for removal of 3-indole butyric acid (IBA) from aqueous media with subsequent determination using HPLC. Percent extraction of IBA was strongly affected by pH of aqueous phases and the chemical structures of ionic liquids (ILs). Extraction of IBA was quantitative in the pH values lower than pK_a of IBA. Considering both extraction and stripping efficiencies of IBA, [C₄mim][PF₆] was found to act more efficient than other studied ILs. Capacity of [C₄mim][PF₆] was 17.6 × 10⁻⁴ mmol IBA per 1.0 mL of IL. Ionic strength of aqueous phase and temperature had shown no serious effects on extraction efficiency of IBA. A preconcentration factor of 100 and a relative standard deviation of 1.16% were obtained. It was found that ionic liquid phase was reusable almost five times for extraction/stripping purposes. 3-Indole acetic acid showed interferential effect in the extraction step. In order to assess the applicability of the method, extraction and stripping of IBA from pea plants and some other samples were studied.     

Electrochemistry of water in 1-butyl-3-methylimidazolium tetrafluoroborate at nickel electrode: application to hydrogen peroxide production and water sensing

The electrochemistry of water dissolved in 1-butyl-3-methylimidazolium tetrafluoroborate ([C₄mim][BF₄]) was studied by cyclic voltammetry and electrochemical impedance spectroscopy using a nickel electrode. Hydrogen peroxide is being produced by direct electrolysis of water in a cooperative process between the nickel electrode and [C₄mim][BF₄]. There is linear response between the concentration of water and the oxidation peak current at 1.60 V. Impedance decreases significantly with increasing concentration of water. The findings resulted in two promising applications: The first is the production of hydrogen peroxide, and the second is in water sensing. Both methods are environmentally friendly and convenient.     

Theoretical study of interactions between 1-alkyl-3-methyimidazolium tetrafluoroborate and dibenzothiophene: DFT,NBO, and AIM analysis

Density functional theory is employed to study the interaction energies between dibenzothiophene (DBT) and 1-alkyl-3-methylimidazolium tetrafluoroborate ([C _n mim]⁺[BF₄]^?). The structures of DBT, 1-ethyl-3-methylimidazolium tetrafluoroborate ([C₂mim]⁺[BF₄]^?), 1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim]+[BF₄]?), 1-hexyl-3-methylimidazolium tetrafluoroborate ([C₆mim]⁺[BF₄]^?), 1-octyl-3-methylimidazolium tetrafluoroborate ([C₈mim]⁺[BF₄]^?), [C₂mim]⁺[BF₄]^?–DBT, [C₄mim]⁺[BF₄]^?–DBT, [C₆mim]⁺[BF₄]^?–DBT and [C₈mim]⁺[BF₄]^?–DBT systems are optimized systematically at the B3LYP/6-31G(d,p) level, and the most stable geometries are obtained by NBO and AIM analyses. The results indicate that DBT and imidazolium rings of ionic liquids are parallel to each other. It is found that the [BF₄]^? anion prefers to be located close to a C1–H9 proton ring in the vicinity of the imidazolium ring and the most stable gas-phase structure of [C _n mim]⁺[BF₄]^? has four hydrogen bonds between [C _n mim]+ and [BF₄]?. There are hydrogen bonding interactions, π–π and C–H–π interactions between [C₈mim]⁺[BF₄]^? and DBT, which is confirmed by NBO and AIM analyses. The calculated interaction energies for the studied ionic liquids can be used to interpret a better extracting ability of [C₈mim]⁺[BF₄]^? to remove DBT, due to stronger interactions between [C₈mim]⁺[BF₄]^? and DBT, in agreement with the experimental results of dibenzothiophene extraction by [C _n mim]⁺[BF₄]^?.     

A new disposable ionic liquid based coating for headspace solid-phase microextraction of methyl tert-butyl ether in a gasoline sample followed by gas chromatography-flame ionization detection

A new ionic liquid (IL) based solid-phase microextraction (SPME) fiber was investigated and used for headspace (HS) extraction of methyl tert-butyl ether (MTBE) in a gasoline sample. Using the new IL coated HS-SPME fiber with the combination of gas chromatography-flame ionization detection (GC-FID); sub-to-low μg L⁻¹ concentrations of MTBE were detected. Four different ILs including 1-butyl-3-methylimidazolium tetraflouroborate ([C₄C₁IM] [BF₄]), 1-octyl-3-methylimidazolium tetraflouroborate ([C₈C₁IM] [BF₄]), 1-octyl-3-methylimidazolium hexaflourophosphate ([C₈C₁IM] [PF₆]) and 1-ethyl-3-methylimidazolium ethylsulphate ([C₂C₁IM] [ETSO₄]) were synthesized and examined for extraction, preconcentration and determination of MTBE. It was observed that [C₈C₁IM] [BF₄] showed the highest extraction efficiency and possessed the best extractability for MTBE. The fiber coating takes up the compounds from the sample by absorption in the case of liquid coatings. The calibration graph was linear in a concentration range of 1-120 μg L⁻¹ (R² > 0.994) with the detection limit of 0.09 μg L⁻¹ level. The new IL-coated fiber was applied successfully for the determination of MTBE in a gasoline sample with good recoveries between 90 and 95%.     

Solubility of H2S in ionic liquids [hmim][PF6], [hmim][BF4], and [hmim][Tf2N]

The solubility of hydrogen sulphide in three ionic liquids, viz. 1-hexyl-3-methylilmidazolium hexafluorophosphate ([hmim][PF₆]), 1-hexyl-3-methylimidazolium tetrafluoroborate ([hmim][BF₄]), and 1-hexyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([hmim][Tf₂N]), at temperatures ranging from 303.15 K to 343.15 K and pressures up to 1.1 MPa were determined. The solubility values were correlated using the Krichevsky–Kasarnovsky equation and Henry’s constants were obtained at different temperatures. Partial molar thermodynamic functions of solvation such as standard Gibbs free energy, enthalpy, and entropy were calculated from the solubility results. Comparison of the values obtained show that the solubility of H₂S in these three ionic liquids was in the sequence: [hmim][BF₄] > [hmim][PF₆] ≈ [hmim][Tf₂N].     

Solubilities of ammonia in basic imidazolium ionic liquids

Solubilities of ammonia in four conventional imidazolium ionic liquids: [C_nmim][BF₄] (n = 2, 4, 6, 8) have been measured. Isothermally fixed temperatures are 293.15, 303.15, 313.15, 323.15 and 333.15 K; the pressure is from 0 to 1.0 MPa. High solubilities of ammonia are found, and it is also found that the solubilities of ammonia increase when the length of cations’ alkyl increases (the ILs have the same anion), that is: [C₈mim]⁺ > [C₆mim]⁺ > [C₄mim]⁺ > [C₂mim]⁺. The solubility data have been correlated by the Krichevisky–Kasarnovsky equation, and then Henry's constants and partial molar volumes of NH₃ at infinite dilution are obtained. The thermodynamic properties such as solution enthalpy (Δ_solH), solution Gibbs free energy (Δ_solG), solution entropy (Δ_solS), and solution heat capacity (Δ_solC_p) of these systems are obtained.     

Phase behaviour of 1-hexyloxymethyl-3-methyl-imidazolium and 1,3-dihexyloxymethyl-imidazolium based ionic liquids with alcohols,water, ketones and hydrocarbons: The effect of cation and anion on solubility

The liquid–liquid equilibrium (LLE), or solid–liquid equilibrium (SLE) of more than 20 binary systems containing 1-hexyloxymethyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)-imide [C₆H₁₃OCH₂MIM][Tf₂N] with alcohol (butan-1-ol, or hexan-1-ol, or octan-1-ol), water and ketone (3-pentanone, or cyclopentanone) and of 1-hexyloxymethyl-3-methyl-imidazolium tetrafluoroborate [C₆H₁₃OCH₂MIM][BF₄] with alcohol (methanol, or ethanol, or butan-1-ol, or hexan-1-ol, or octan-1-ol), water and ketone (3-pentanone, or cyclopentanone) have been measured. The solubility of dialkoxy-imidazolium salts: (1) 1,3-dihexyloxymethyl-imidazolium bis(trifluoromethylsulfonyl)-imide [(C₆H₁₃OCH₂)₂IM][Tf₂N] in alcohol (butan-1-ol, or hexan-1-ol, or octan-1-ol, or decan-1-ol), in water and hydrocarbon (benzene, hexane and cyclohexane); (2) 1,3-dihexyloxymethyl-imidazolium tetrafluoroborate [(C₆H₁₃OCH₂)₂IM][BF₄] in alcohol (hexan-1-ol, or octan-1-ol, or decan-1-ol) and water have been measured. Measurements were carried out by using a dynamic method from T = 275 K to the boiling point of the solvent. In this work a systematic study of the impact of different factors on the phase behaviour of hexyloxy-imidazolium-based ionic liquids with polar and nonpolar solvents has been presented. Most of the examined systems showed immiscibility in the liquid phase with an upper critical solution temperature (UCST), or complete solubility of the ionic liquid at room temperature in many solvents. An increase in the alkyl chain length of alcohol resulted in an increase in the UCST. The choice of anion was shown to have large impact on the solubility: by changing the anion [Tf₂N]⁻ to [BF₄]⁻, the solubility dramatically decreased and the UCST increased. By contrast, increasing hydrogen bonding opportunities with the solvent by replacing a methyl group with the second alkoxy-group on the imidazolium ring results in an increase of the solubility.