A novel method of metal ion removal and recovery from water by complex formation with polyelectrolytes

A novel method of metal removal and recovery and recovery is described. This method may be useful in connection with various types of water pollution. It is based on the fact that metal ions form water-soluble complexes with water-soluble polyelectrolytes, such as polyacids. These complexes can be precipitated with polybases and the metal can be recovered by treating the precipitate with mineral acid. The remaining polymer complex can be used again for further precipitation. Experiments with Cu²⁺ and Co²⁺ ions are given in some detail; general observations concerning other cases are included.     

Simultaneous determination of iron(III) and vanadium(V) with N-phenylcinnamohydroxamic acid and thiocyanate by extraction-spectrophotometry

N-Phenylcinnarnohydroxamic acid (PCHA) reacts with iron(III) and vanadium(V) in the presence of thiocyanate to form water-insoluble orange and green complexes, respectively. The iron(III)-PCHA and vanadium(V)-PCHA-thiocyanate complexes can be quantitatively extracted into toluene and other common organic solvents at pH 1.5–2.0. The absorption spectra and composition of both complexes are described. The effects of foreign ions and of experimental variables on the extraction and determination of the two metal ions are studied. A simple, selective method is described for the simultaneous determination of iron(III) and vanadium(V) by extraction-spectrophotometry; absorbances are measured at 440 and 580 nm. Mixtures can be determined over the range 10^?4–10^?5 M in each metal. The method was applied successfully to the analysis of standard steels for iron and vanadium.     

Determination of the oxygen balance in oxide superconductors by a photometric method

Summary A photometric method is described for determining the oxygen balance in oxide superconductors. It is based on the oxidation of Fe²⁺ to Fe³⁺ by the superconductors and the following determination of the residual Fe²⁺ ions as complex with 1,10-phenanthroline. Hydrobromic acid is used for dissolving the samples. The method has been developed for 10 mg sample weights. Good reliability of the method was verified by comparison with the cerimetric determination using 80 mg samples.     

Coordination Chemical Studies of Some Polymeric Transition Metal Complexes with Neomycin and Their Biological Activity Uses. Indirect Determination of Neomycin by Atomic Absorption Spectroscopy (AAS)

Abstract

A new series of polymeric[M(Neom)H₂ ^O)x]n complexes have been prepared; where M= Co(II), Ni(II), Cu(II) or Zn(II) ions, Neom = neomycin and X = 2–4. The complexes have been characterized by elemental analysis, conductance and magetic moment measurements. IR spectra indicated that the bonding between neomycin and transition metal ions takes place through M-O bonds. Electronic and EPR spectra of the solid complexes are measured in order to gain information about their structurs and geometry. X- ray diffraction patterns indicated that the complexes are amorphous. The biological activity of the complexes formed has been tested towards eight microorganisms and compared with the activity of neomycin itself. A new method is described for the indirect estimation of neomycin by atomic absorption spectroscopy (AAS) using carbonate as an auxiliary ligand. The results obtained either for the pure form or in pharmaceutical formulations are accurate and precise.     

Study of Host-Guest Complexation of Alkaline Earth Metal Ion,Aluminum Ion and Transition Metal Ions with Crown Ethers by Fast Atom Bombardment Mass Spectrometry

Complexations of crown ethers with alkali metal ions have been investigated extensively by FAB mass spectrometry over the past decade, but very little attention has been paid to reactions of crown ethers with other classes of metal ions such as alkaline earth metal ions, transition metal ions and aluminum ions. Although fast atom bombardment ionization mass spectrometry has proven to be a rapid and convenient method to determine the binding interactions of crown ethers with metal ions, problems in reliabilities for quantitative measurements of” binding strength for the host-guest complexes have been described in the literature. Thus, in this paper, applications of FAB/MS for investigating the complexation of crown ethers with various classes of metal ions is discussed. Extensive fragmentations for neutral losses such as C₂H₄O or C₂H₄ molecules from the host-guest complexes could be observed. The reason is attributed to the energetic bombardment processes of FAB occuring in the formation of these complexes. Complexes of cyclen with metal ions also show neutral losses of C₂H₄NH molecules leading to fragment ions. Transition metal ions usually form (Crown + MCl)⁺ type of ions, alkaline earth metal ions can form both (Crown + MCl)⁺ and (Crown + MOH)⁺ type of ions. But for aluminum ions, only (Crown + Al(OH)₂)⁺ type of ions could he observed.     

A matrix method for calculating the magnetic properties of Co2+ complex ions

A matrix method for calculating of the magnetic properties of Co²⁺ complex ions is proposed. The method involves calculations of a full matrix of all interactions existing in the ion. The theoretical results obtained by this method more accurately describe the observed experimental values of magnetic parameters of mononuclear complexes with Co²⁺ ions.     

The electrochemical determination of ammonium based on the selective inhibition of the low-spin iron(II)/(III) system of Prussian blue

A new method is described for the determination of ammonium in aqueous solutions with electrodes modified by Prussian blue (PB). The specific voltammetric response of PB-modified electrodes to ammonium ions is used for their analytical determination. In the presence of ammonium ions, a concentration-dependent inhibition of the low-spin iron(II/III) system of PB occurs. Only thallium and rubidium ions cause similar inhibition. A useful electrochemical determination method is thus available for detecting ammonium ions in the presence of frequently interfering potassium and sodium ions. Paraffin-impregnated graphite electrodes modified with a mechanically transferred PB layer and bulk-modified PB-composite electrodes are studied. The method is applicable within a concentration range which extends from 4 × 10⁻⁵ mol/l to 10⁻² mol/l NH₄ ⁺. The composite electrode is used in an electrochemical flow-through system in conjunction with the Kjeldahl method. Received: 21 April 1997 / Accepted: 28 May 1997     

Preconcentration of Cr(III), Co(II), Cu(II), Fe(III) and Pb(II) as calmagite chelates on cellulose nitrate membrane filter prior to their flame atomic absorption spectrometric determinations

A method for the preconcentration and determination of Cr(III), Co(II), Cu(II), Fe(III) and Pb(II) ions by atomic absorption spectrometry has been described. The method was based the collection of metal-calmagite complexes on a soluble cellulose nitrate membrane filter. The detection of the solution was obtained by flame atomic absorption spectrometry (FAAS) after completely dissolving the membrane with 0.5 ml of nitric acid at 80 degrees C. The metal ions were recovered quantitatively at pH 8. Various factors which affect the collection and determination of metal ions such as, type and size of the membrane filter, solvent for dissolution of the species retained on the filter were investigated. The detection limits were varying 0.06 mug l(-1) for Cu to 2.5 mug l(-1) for Cr. An application of the proposed method for analyte ions in mineral and tap water samples was also described with satisfactory results (recoveries >95%, relative standard deviations <10%).     

Spectrophotometric determination of iron(III) with chrome azurol s or eriochrome cyanine r and some cationic surfactants

Sensitive spectrophotometric methods for the determination of iron(III), based on ternary complexes with a triphenylmethane reagent, chrome azurol S (CAS) or eriochrome cyanine R (ECR), and cetyltrimethylammonium (CTA) or cetylpyridinium (CP) ions, are described. For the system Fe—CAS—CTA, the molar absorptivity is 1.35 × 10⁵ l mol^-1 cm^-1 at 645 nm; for Fe—ECR—CTA it is 1.28 × 10⁵ l mol^-1 cm^-1 at 635 nm. Maximum absorbance is attained (at about pH 4) when the molar ratio (to iron) or CAS or ECR is about 20 and that of CTA or CP is 60–80. Citrate, tartrate, oxalate and EDTA interfere. Interference by metals (e.g. Be, Al, Ga, In, Sc, Zr, Th) can be eliminated by preliminary extraction of iron(III) as thiocyanate complex. The method was successfully applied to determining traces of iron in analytical-grade sodium hydroxide.     

Spectrophotometric study of reactions of scandium,ytrium and lanthanum ions with some triphenylmethane dyes in the presence of cationic surfactants

Optimum conditions for the formation of ternary complexes of scandium, ytrium and lanthanum ions with chrome azurol S, eriochrome cyanine R and pyrocatechol violet in the presence of cetyltrimethylammonium, cetypyridinium and tetradecyldimethylbenzyl-ammonium (zephiramine) ions are described. The spectrophotometric determination of scandium with chrome azurol S and zephiramine exhibits the greatest sensitivity (? = 1.50 × 10⁵ l mol^?1 cm^?1 at 610 nm). In the spectrophotometric determination of scandium with eriochrome cyanine R and cetylpyridinium ion (? = 9.2 × 10⁴ at 600 nm), the interference caused by yttrium is the least. In the best method for yttrium (with pyrocatechol violet and zephiramine), the molar absorptivity is 3.3 × 10⁴ at 660 nm. Lanthanum does not form ternary complexes of analytical interest in these systems. Some aspects of the formation of ternary complexes with cationic surfactants are discussed.     

Flotation separation of hafnium(IV) from aqueous solutions

A simple, rapid method for the separation of hafnium from aqueous solutions has been investigated using^(175+181)Hf tracer. Cationic hafnium complex ions were floated from dilute acid solutions with sodium lauryl sulfate (SLS) and anionic hafnium complexes were floated from basic and oxalic acid solutions with hexadecyltrimethyl ammonium bromide (HTMAB). The conditions necessary for quantitative recovery of the metal and mechanisms of flotation are described.Author to whom correspondence should be addressed.     

Monothiourea-3-nitrophthalic acid as a new reagent for spectrophotometric analyses: I. Determination of palladium(II) ions

The results of the examination of the reaction between a new reagent, MT3NF acid, and palladium(II) ions, as well as the composition of the formed complexes have been discussed. The new extraction-spectrophotometric method for the determination of palladium(II) ions by using MT3NF acid was presented. Beer's law is obeyed over the range 0.1 to 3 μg of Pd/cm³. Molar absorptivity is 2.9 × 10⁴ liter mol^?1 cm^?1 at the absorption maximum of 306 nm. The influence of different ions has been described.     

Separation and microdetermination of rare earth metals with N-phenylbenzohydroxamic acid and Xylenol Orange

A simple, sensitive and selective method for solvent extraction and spectrophotometric determination of lanthanum(III), praseodymium(III), neodymium(III) and samarium(III) is described. The rare earth metals are extractable into chloroform solution of N-phenylbenzohydroxamic acid (PBHA) at pH9–10. Various parameters are studied to optimize the extraction conditions. Stoichiometry of the complexes and the effect of various ions is discussed. The molar absorptivity is found to increase from 65,000 to 93,000 1·mol^–1· cm^–1 with the increase in atomic number of the rare earths. The stability constants of the complexes, separation factors and pH_{5 0} are discussed.     

Spectrophotometric Determination of Copper in Natural Waters and Pharmaceutical Samples with Chloro(Phenyl) Glyoxime

A simple method for the determination of trace amounts of copper by spectrophotometry is described based on the formation of the copper‐chloro‐(phenyl) glyoxime complex. The molar absorptivities of the complexes at pH 4.0 at 290.5 nm were 0.8 × 10⁴l/mol cm. Optimal conditions such as reagent amounts and pH for the copper determination were reported. The effects of the foreign ions were also investigated. The method was successfully applied for determinations of copper in some natural waters and pharmaceutical samples.     

Selective detection of specific protein-ligand complexes by electrosonic spray-precursor ion scan tandem mass spectrometry

A novel mass spectrometric method for the selective detection of specific protein-ligand complexes is presented. The new method is based on electrosonic spray ionization of samples containing protein and ligand molecules, and mass spectrometric detection using the precursor ion scanning function on a triple quadrupole instrument. Mass-selected intact protein-ligand complex ions are subjected to fragmentation by means of collision-induced dissociation in the collision cell of the instrument, while the second mass analyzer is set to the m/z of protonated ligand ions or their alkali metal adducts. The method allows for the detection of only those ions which yield ions characteristic of the ligand molecules upon fragmentation. Since the scan range of first analyzer is set well above the m/z of the ligand ion, and the CID conditions are established to permit fragmentation of only loosely bound, noncovalent complexes, the method is specific to the detection of protein-ligand complexes under described conditions. Behavior of biologically specific and nonspecific complexes was compared under various instrumental settings. Parameters were optimized to obtain maximal selectivity for specific complexes. Specific and nonspecific complexes were found to show markedly different fragmentation characteristics, which can be a basis for selective detection of complexes with biological relevance. Preparation of specific and nonspecific complexes containing identical building blocks was attempted. Complex ions with identical stoichiometry but different origin showed the expected difference in fragmentation characteristics, which gives direct evidence for the different mechanism of specific versus nonspecific complex ion formation.     

Some analytical applications of aromatic sulfonyl haloamines: Determination of thiocyanate and cyanide ions in metal complexes and salts and thiosemicarbazide in metal complexes with bromamine-T

A simple, rapid, and accurate method for the determination of thiocyanate and cyanide ions in metal complexes and salts, and thiosemicarbazide (TSC) in Zn, Cd, Hg, Ni, Pt, and Pd metal complexes with excess of bromamine-T has been developed. The oxidation involves eight- and two-electron changes, respectively, with NCS^? and CN^? ions and a 12-electron stoichiometry per TSC molecule, in 0.1–0.2 N NaOH medium. The proposed method could be employed for computing the number of thiocyanate, cyanide, and TSC ligands in the respective complexes. The aromatic sulfonyl haloamine, bromamine-T, has been prepared and characterized by uv, ir, and FT NMR ¹H and ¹³C spectral data and its mass spectrum.     

Investigation of complex formation between poly(N-vinyl imidazole) and various metal ions using the molar ratio method

The complex formation of poly(N-vinyl imidazole) (PVIm) with various metal ions was studied. UV-vis spectroscopy was employed to study the interaction of PVIm and metal ions in aqueous solution. Formation constants of PVIm-metal complexes were calculated by applying a “mole ratio” method. The stoichiometric ratios between polymer and metal ions were found to be␣4. The stability constants for the complexes of PVIm with bivalent transition metal ions were in agreement with the Irving-William series. The biggest formation constant was found for the PVIm-Cu²⁺ complex system. Received: 4 January 1999 Accepted in revised form: 1 February 1999     

A post-column photochemical detector for use in the determination of trace metals with n-butyl-2-naphthylmethyldithiocarbamate by high-performance liquid chromatography

The determination of traces of metals by high-performance liquid chromatography of their n-butyl-2-naphthylmethyldithiocarbamate (BNMDTC) complexes on a nonpolar stationary phase, with a post-column photochemical detector is described. Metal complexes of this ligand are thermodynamically stable and kinetically inert towards dissociation. To provide low detection limits, a photochemical reactor was developed to generate a fluorescent product. A major product of the photolysis of BNMDTC complexes is identified as the highly fluorescent n-butyl-2-naphthyl-methylamine. Detection of metal ions as BNMDTC complexes at the 10^?8 M level is feasible. Iron, nickel, mercury and cobalt complexes are readily determined.     

Monothiourea-3-nitrophthalic acid as a new reagent for spectrophotometric analyses : II. Determination of ruthenium(III) ions

The results of the examination of the reaction between a new reagent, MT3NF acid, and palladium(II) ions, as well as the composition of the formed complexes have been discussed. The new extraction-spectrophotometric method for the determination of palladium(II) ions by using MT3NF acid was presented. Beer's law is obeyed over the range 0.1 to 3 μg of Pd/cm³. Molar absorptivity is 2.9 × 10⁴ liter mol⁻¹ cm⁻¹ at the absorption maximum of 306 nm. The influence of different ions has been described.     

On-Line Solid Phase Extraction and Simultaneous Determination of Hafnium and Zirconium by ICP–Atomic Emission Spectroscopy

A new simple flow injection analysis (FIA) system is described for on-line preconcentration by solid phase extraction and simultaneous determination of Hf and Zr in different samples using inductively coupled plasma atomic emission spectroscopy with a charge coupling detector (CCD). Quinalizarin (QA) was loaded on an octadecyl silica-polyethylene mini-column for the retention of Hf and Zr ions in complexed form. A 0.3 M ammonium acetate was used as buffer for providing suitable conditions for complexation and increasing reproducibility. Retained ions on the solid phase were then eluted by a solution containing 3.0 M HCl and 0.5 M HNO₃. In this work, for reducing bandwidths of eluted ions, elution of minicolumn was carried out from opposite direction. The same solution was used as both carrier and eluent, in order to increase the reproducibility. The eluted ions were introduced into the conventional nebulizer of ICP–AES instrument. Effects of different parameters, including instrumental parameters of ICP and FIA were optimized. An enrichment factor of 330 for each analyte ion was obtained at a concentration level of 80 ppb. The detection limits of the proposed method for Hf and Zr were 0.16 ng mL⁻¹ and 0.04 ng mL⁻¹ respectively. The ability of the method for the recovery of Hf and Zr ions was tested in the presence of several diverse metal ions in a synthetic mixture and some real matrices. It was also applied to the determination of Zr and Hf ions in a standard soil and in a standard alloy as real samples.