Living radical graft polymerization of methyl methacrylate to polyethylene film with typical and reverse atom transfer radical polymerization

Nickel‐mediated atom transfer radical polymerization (ATRP) and iron‐mediated reverse ATRP were applied to the living radical graft polymerization of methyl methacrylate onto solid high‐density polyethylene (HDPE) films modified with 2,2,2‐tribromoethanol and benzophenone, respectively. The number‐average molecular weight (M_n) of the free poly(methyl methacrylate) (PMMA) produced simultaneously during grafting grew with the monomer conversion. The weight‐average molecular weight/number‐average molecular weight ratio (M_w/M_n) was small (<1.4), indicating a controlled polymerization. The grafting ratio showed a linear relation with M_n of the free PMMA for both reaction systems. With the same characteristics assumed for both free and graft PMMA, the grafting was controlled, and the increase in grafting ratio was ascribed to the growing chain length of the graft PMMA. In fact, M_n and M_w/M_n of the grafted PMMA chains cleaved from the polyethylene substrate were only slightly larger than those of the free PMMA chains, and this was confirmed in the system of nickel‐mediated ATRP. An appropriate period of UV preirradiation controlled the amount of initiation groups introduced to the HDPE film modified with benzophenone. The grafting ratio increased linearly with the preirradiation time. The graft polymerizations for both reaction systems proceeded in a controlled fashion. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3350–3359, 2002     

Synthesis of well-defined, polymer-grafted silica nanoparticles via reverse ATRP

The surface grafting onto ultrafine silica via reverse ATRP of methyl methacrylate initiated by peroxide groups introduced onto the surface and conventional ATRP of Styrene initiated by the hybrid nanoparticles were investigated. The introduction of peroxide groups onto the silica surface was achieved by the reaction of hydrogen peroxide with chlorosilyl groups, which were introduced by the treatment of silica with thionyl chloride. Well-defined polymer chains were grown from the nanoparticle surfaces to yield individual particles composed of a silica core and a well-defined, densely grafted outer polymer layer. The polymerization was closely controlled in solution at quite low temperature such as 70 °C. In both cases, linear kinetic plots, linear plots of molecular weight (M_n) versus conversion, in hydrodynamic diameter with increasing conversion, and narrow molecular weight distributions (M_w/M_n) for the grafted polymer samples were observed. Hydrolysis of silica cores by hydrofluoric acid treatment enabled characterization of cleaved polymer using GPC. Ultrathin films of hybrid nanoparticles were examined using TEM and AFM.     

Graft polymerization from pore wall of three-dimensionally ordered macroporous cross-linked polystyrene via atom transfer radical polymerization

The surface-initiated atom-transfer radical polymerization (ATRP) technique was applied to the graft polymerization of methyl methacrylate (MMA) and N-isopropylacrylamide (NIPAm) from three-dimensionally ordered macroporous cross-linked polystyrene (3DOM CLPS) on which the initiator, halogen atom was immobilized onto the pore wall of 3DOM CLPS by chloromethylation. FT-IR and TG-DWA analyses confirm that the graft polymerization of MMA and NIPAm via ATRP had been taken place at the pore wall of 3DOM CLPS. The initiating efficiency of chloromethyl groups was calculated according to the data of TGA-titration, revealed that the benzyl chloride is not only distributed on the surface of the pore walls but also must be present throughout the inner of the cross-linked polystyrene matrix. SEM analyses show that the grafted layers are smooth and homogeneous, and the ordered structure is well preserved after polymerization. By the adjustment of the graft polymerization time, the thickness of grafted polymer layers can be controlled. The max thickness of grafted PMMA layer is 85 nm and the max thickness of grafted PNIPAm layer is 35 nm.     

Preparation of poly(methyl methacrylate) grafted hydroxyapatite nanoparticles via reverse ATRP

Surface-initiated reverse atom transfer radical polymerization (reverse ATRP) technical was successfully employed to modify hydroxyapatite (HAP) nanoparticles with poly(methyl methacrylate) (PMMA). The peroxide initiator moiety for reverse ATRP was covalently attached to the HAP surface through the surface hydroxyl groups. Reverse ATRP of methyl methacrylate (MMA) from the initiator-functionalized HAP was carried out, and the end bromide groups of grafted PMMA initiated ATRP of MMA subsequently. Fourier transformation infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM) were employed to confirm the grafting and to characterize the nanoparticle structure. The grafted PMMA gave HAP nanoparticles excellent dispersibility in MMA monomer. As the amount of grafted PMMA increased, the dispersibility of surface-grafted HAP and the compressive strength of HAP/PMMA composites were improved.     

Synthesis of Poly(methyl methacrylate)-poly(poly(ethylene glycol) methacrylate)-polyisobutylene ABCBA Pentablock Copolymers by Combining Quasiliving Carbocationic and Atom Transfer Radical Polymerizations and Characterization Thereof

Novel, unique amphiphilic pentablock terpolymers consisting of the highly hydrophobic polyisobutylene (PIB) mid-segment attached to the hydrophilic combshaped poly(poly(ethylene glycol) methacrylate) (PPEGMA) polymacromonomer chains, which are coupled to poly(methyl methacrylate) (PMMA) outer segments were synthesized by the combination of quasiliving carbocationic polymerization and atom transfer radical polymerization (ATRP). First, a bifunctional PIB macroinitiator was prepared by quasiliving carbocationic polymerization and subsequent quantitative chain end derivatizations. Quasiliving ATRP of PEGMAs with different molecular weights (M_n = 188, 300 and 475 g/mol) led to triblock copolymers which were further reacted with MMA under ATRP conditions to obtain PMMA-PPEGMA-PIB-PPEGMA-PMMA ABCBA-type pentablock copolymers. It was found that slow initiation takes place between the PIB macroinitiator and PEGMA macromonomers with higher molecular weights via ATRP. ATRP of MMA with the resulting block copolymers composed of PIB and PPEGMA chain segments led to the desired block copolymers with high initiating efficiency. Investigations of the resulting pentablock copolymers by DSC, SAXS and phase mode AFM revealed that nanophase separation occurs in these new macromolecular structures with average domain distances of 11-14 nm, and local lamellar self-assembly takes place in the pentablocks with PPEGMA polymacromonomer segments of PEGMAs with M_n of 118 g/mol and 300 g/mol, while disordered nanophases are observed in the block copolymer with PEGMA having molecular weight of 475 g/mol. These new amphiphilic block copolymers composed of biocompatible chain segments can find applications in a variety of advanced fields.     

Facile surface immobilization of ATRP initiators on colloidal polymers for grafting brushes and application to colloidal crystals

Bromo-initiators for atom transfer radical polymerization (ATRP) were successfully immobilized on the surfaces of cross-linked poly(methyl methacrylate) (PMMA) spheres by soap-free emulsion polymerization using CBr(4) as the chain transfer agent. Subsequent surface-initiated ATRP (SI-ATRP) afforded a layer of PMMA brushes covalently attached to the sphere surfaces. Colloidal crystal films of these monodisperse spheres were then studied to identify the relationship between variation in particle diameter and the optical properties. The particle diameters were controlled by varying the feed monomer proportions in soap-free emulsion polymerization and the thickness of the grafted brush layer. It was found that the particle diameter could successfully be controlled to obtain crystal films that produce a variety of brilliant colors in the visible region. The results of this study can provide useful information for facile preparation of surface-immobilized ATRP initiators on colloidal polymers and can be employed for grafting polymer brushes.     

Protein–polymer hybrids: Conducting ARGET ATRP from a genetically encoded cleavable ATRP initiator

Protein–polymer hybrids are an important class of biomaterials. Described is the preparation of a genetically incorporated a non-canonical amino acid (nCAA) containing an ester linked atom transfer radical polymerization (ATRP) initiator, followed by a controlled “grafting from” polymerization. A Methanococcus jannaschii tyrosyl-tRNA synthetase/tRNA_CUA pair was selected to genetically encode p-bromoisobutyryloxymethyl-l-phenylalanine (biF) in response to an amber codon. This biF was directly incorporated into green fluorescent protein (GFP) at residue 134 generating biF-GFP. Activators regenerated by electron transfer (ARGET) ATRP was conducted under biologically relevant conditions to graft well-defined poly(oligo ethylene oxide methacrylate) from the biF-GFP. The biF-GFP retained its biofluorescence properties throughout the polymerization indicating the utility of ARGET ATRP for preparing protein–polymer hybrids. The presence of a base-labile ester bond in the initiator, allowed cleavage of the grafted polymer from the protein and directly analyze their molecular weight and molecular weight distribution using gel permeation chromatography (GPC). The cleaved final polymer had a M_n = 27,000 and a molecular weight distribution of M_w/M_n = 1.27.     

Construction of a comb-like glycosylated membrane surface by a combination of UV-induced graft polymerization and surface-initiated ATRP

Carbohydrate residues are found on the extracellular side of the cell membrane. They form a protective coating on the outer surface of the cell and are involved in intercellular recognition. Synthetic carbohydrate-based polymers, so-called glycopolymers, are emerging as important well-defined tools for investigating carbohydrate-based biological processes and for simulating various functions of carbohydrates. In this work, the surface of a polypropylene microporous membrane (PPMM) was modified with comb-like glycopolymer brushes by a combination of UV-induced graft polymerization and surface-initiated atom-transfer radical polymerization (ATRP). 2-Hydroxyethyl methacrylate (HEMA) was first grafted to the PPMM surface under UV irradiation in the presence of benzophenone and ferric chloride. ATRP initiator was then coupled to the hydroxyl groups of poly(HEMA) brushes. Surface-initiated ATRP of a glycomonomer, D-gluconamidoethyl methacrylate, was followed at ambient temperature in aqueous solvent. Water had a significant acceleration effect on the ATRP process; however, loss of control over the polymerization process was also observed. The addition of CuBr2 to the ATRP system largely increased the controllability at the cost of the polymerization rate. The grafting of HEMA, the coupling of ATRP initiator to the hydroxyl groups, and the surface-initiated ATRP were confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy.     

Synthesis of well‐defined polymer brushes on the surface of zinc antimonate nanoparticles through surface‐initiated atom transfer radical polymerization

Zinc antimonate nanoparticles consisting of antimony and zinc oxide were surface modified in a methanol solvent medium using triethoxysilane‐based atom transfer radical polymerization (ATRP) initiating group (i.e.,) 6‐(2‐bromo‐2‐methyl) propionyloxy hexyl triethoxysilane. Successful grafting of ATRP initiator on the surface of nanoparticles was confirmed by thermogravimetric analysis that shows a significant weight loss at around 250–410 °C. Grafting of ATRP initiator onto the surface was further corroborated using Fourier transform Infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS). The surface‐initiated ATRP of methyl methacrylate (MMA) mediated by a copper complex was carried out with the initiator‐fixed zinc antimonate nanoparticles in the presence of a sacrificial (free) initiator. The polymerization was preceded in a living manner in all examined cases; producing nanoparticles coated with well defined poly(methyl methacrylate) (PMMA) brushes with molecular weight in the range of 35–48K. Furthermore, PMMA‐grafted zinc antimonate nanoparticles were characterized using Thermogravimetric analysis (TGA) that exhibit significant weight loss in the temperature range of 300–410 °C confirming the formation of polymer brushes on the surface with the graft density as high as 0.26–0.27 chains/nm². The improvement in the dispersibility of PMMA‐grafted zinc antimonate nanoparticles was verified using ultraviolet‐visible spectroscopy and transmission electron microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

A controlled approach to iron oxide nanoparticles functionalization for magnetic polymer brushes

In this article, we report a detailed study of surface modification of magnetite nanoparticles by means of three different grafting agents, functional for the preparation of magnetic polymer brushes. 3-Aminopropyltriethoxysilane (APTES), 3-chloropropyltriethoxysilane (CPTES), and 2-(4-chlorosulfonylphenyl)ethyltrichlorosilane (CTCS) were chosen as grafting models through which a wide range of polymer brushes can be obtained. By means of accurate thermogravimetric analysis a good control over the amount of immobilized molecules is achieved, and optimal operating conditions for each grafting agent are consequently determined. Graft densities ranging from approximately 4 to 7 molecules per nm(2) are obtained, depending on the conditions used. In addition, the surface-initiated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) carried out with CTCS-coated nanoparticles is presented as an example of polymer brushes, leading to a well-defined and dense polymeric coating of around 0.6 PMMA chains per nm(2).     

Surface‐initiated atom transfer radical polymerization grafting of poly(2,2,2‐trifluoroethyl methacrylate) from flat silicon wafer surfaces

Poly(2,2,2‐trifluoroethyl methacrylate) (PTFEMA), a partially fluorinated polymer, was directly grafted from silicon wafer surfaces by a surface‐initiated atom‐transfer radical polymerization (ATRP). The polymer layer thickness increased linearly with monomer conversion and molecular weight of free polymers in solution. The thickness was mainly determined by the experimental conditions such as activator/deactivator ratio, monomer/catalyst ratio, and monomer concentration. PTFEMA layers of more than 100‐nm thick were obtained. The grafted PTFEMA chains were “living” and allowed the extension of a second block of PMMA. X‐ray photoelectron spectroscopy study showed that the chemical compositions at the surfaces agreed well with their theoretical values. A novel surface‐attachable difunctional initiator was also synthesized and applied to the grafting of PTFEMA. The grafting density was doubled using this difunctional initiator, from 0.48 to 0.86 chains/nm². © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1252–1262, 2006     

Reverse Atom Transfer Radical Polymerization of MMA in the Presence of CaCO3/SiO2 Two-Component Composite Particles

Summary: We previously discovered that structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, can be achieved via reverse atom transfer radical polymerization (ATRP), using 2,2′-azo-bis-isobutyronitrile as initiator and Cu^II bromide as catalyst. In the present study, the influence of the mass ratio of CaCO₃/SiO₂ two-component composite particles to methyl methacrylate (MMA) on the rate and behavior of the polymerization was studied in detail. The results illustrate that increasing the mass ratio of CaCO₃/SiO₂ two-component composite particles will decrease the overall rate of polymerization of MMA under standard reverse ATRP conditions. Thermal properties of the obtained well-defined particles were characterized and determined by thermogravimetric analysis (TGA). The results indicate that well-defined PMMA chains grafted on the surface of CaCO₃/SiO₂ particles were only degraded by random chain scission of C C linkages within the PMMA chain, which is different from the degradation of PMMA chains prepared via traditional radical polymerization. This difference is reasonably ascribed to the difference between the end groups of PMMA prepared via reverse ATRP and that via traditional radical polymerization, which has been confirmed by end group analysis measured by ¹H–NMR spectroscopy.     

Effective grafting of polymers onto ultrafine silica surface: Photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface and Mn2(CO)10

The effective grafting of vinyl polymers onto an ultrafine silica surface was successfully achieved by the photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface with Mn₂(CO)₁₀ under UV irradiation at 25 °C. The introduction of trichloroacetyl groups onto the surface of silica was achieved by the reaction of trichloroacetyl isocyanate with surface amino groups, which were introduced by the treatment of silica with 3‐aminopropyltriethoxysilane. During the polymerization, the corresponding polymers were effectively grafted onto the surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mn₂(CO)₁₀. The percentage of poly(methyl methacrylate) grafting onto the silica reached 714.6% after 90 min. The grafting efficiency (proportion of grafted polymer to total polymer formed) in the polymerization of methyl methacrylate was very high, about 80%, indicating the depression of formation of ungrafted polymer. Polymer‐grafted silica gave a stable colloidal dispersion in good solvents for grafted polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2157–2163, 2001     

Glass Transition Temperature Improvement for Polychloroprene by One-Step ATRP Reaction

Polymethyl methacrylate (PMMA) polymer chains were grafted on neoprene W (NW) by a one-step ATRP reaction. The thermal properties of the products were analyzed by DSC. Improvement of T _g was a result of the PMMA grafted chains. Also, the melting point (T _m ) changed from 42°C for NW to 142°C for modified NW. Using different solvents for the resulting copolymers, aggregates were obtained. Phase separation was influenced by the grafting degree of PMMA and the employed solvent. The copolymers were analyzed by GPC, FT-IR, DSC, and SEM.     

Fuzzy ternary particle systems by surface-initiated atom transfer radical polymerization from layer-by-layer colloidal core-shell macroinitiator particles

We report the synthesis of ternary polymer particle material systems composed of (a) a spherical colloidal particle core, coated with (b) a polyelectrolyte intermediate shell, and followed by (c) a grafted polymer brush prepared by surface-initiated polymerization as the outer shell. The layer-by-layer (LbL) deposition process was utilized to create a functional intermediate shell of poly(diallyl-dimethylammonium chloride)/poly(acrylic acid) multilayers on the colloid template with the final layer containing an atom transfer radical polymerization (ATRP) macroinitiator polyelectrolyte. The intermediate core-shell architecture was analyzed with FT-IR, electrophoretic mobililty (zeta-potential) measurements, atomic force microscopy, and transmission electron microscopy (TEM) techniques. The particles were then utilized as macroinitiators for the surface-initiated ATRP grafting process for poly(methyl methacrylate) polymer brush. The polymer grafting was confirmed with thermo gravimetric analysis, FT-IR, and TEM. The polymer brush formed the outermost shell for a ternary colloidal particle system. By combining the LbL and surface-initiated ATRP methods to produce controllable multidomain core-shell architectures, interesting functional properties should be obtainable based on independent polyelectrolyte and polymer brush behavior.     

Atom transfer radical polymerization of methyl methacrylate catalyzed by ion exchange resin immobilized Co(II) hybrid catalyst

Ion exchange resin immobilized Co(II) catalyst with a small amount of soluble CuCl₂/Me₆TREN catalyst was successfully applied to atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in DMF. Using this catalyst, a high conversion of MMA (>90%) was achieved. And poly(methyl methacrylate) (PMMA) with predicted molecular weight and narrow molecular weight distribution (M_w/M_n = 1.09–1.42) was obtained. The immobilized catalyst can be easily separated from the polymerization system by simple centrifugation after polymerization, resulting in the concentration of transition metal residues in polymer product was as low as 10 ppm. Both main catalytic activity and good controllability over the polymerization were retained by the recycled catalyst without any regeneration process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1416–1426, 2008     

Surface modification of silica nanoparticles by UV-induced graft polymerization of methyl methacrylate

In this study we modified the surface of silica nanoparticles with methyl methacrylate by UV-induced graft polymerization. It is a surface-initiated polymerization reaction induced by ultraviolet irradiation. The resulting organic-inorganic nanocomposites were near-monodisperse and fabricated without homopolymerization of the monomer. Substantial increase in mean particle size was observed by SEM image analysis after UV-induced grafting of methyl methacrylate onto pure silica particles. FT-Raman spectroscopy and X-ray photoelectron spectroscopy studies of these materials revealed the successful grafting of methyl methacrylate onto the silica surface. The formation of a covalent bond between the grafted PMMA chains and silica surface was indicated by FT-Raman spectra. Thermogravimetric analysis of the PMMA-grafted silica particles indicated the polymer contents in good agreement with SEM photographs.     

Synthesis and characterization of well-defined poly(methyl methacrylate)/CaCO3/SiO2 three-component composite particles via reverse atom transfer radical polymerization

The attempt to prepare structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, via reverse atom transfer radical polymerization (ATRP), using 2-2′-azo-bis-isobutyronitrile as initiator and Cu(II) bromide as catalyst was reported. CaCO₃/SiO₂ two-component composite particles were first obtained through sol–gel method, and their morphology and surface element information were determined by transmission electron microscopy and X-ray photoelectron spectroscopy, respectively. The results indicate that the CaCO₃ was encapsulated by the obtained SiO₂. After being modified by silane coupling agent, the CaCO₃/SiO₂ composite particles copolymerized with methyl methacrylate (MMA) under standard reverse ATRP conditions to produce PMMA/CaCO₃/SiO₂ three-component composite particles. In the case concerned, first-order kinetic plots and linear increase of molecular weight (Mn) vs conversion and narrow molecular weight distribution for the graft polymer samples were observed. Furthermore, the gel permeation chromatography results illustrated that both the free PMMA chains from the solvent and the graft PMMA chains from the surface of CaCO₃/SiO₂ two-component composite particles were growing at the same rate. Characterizations of the PMMA-grafted CaCO₃/SiO₂ composite particles were done by Fourier transform infrared and thermogravimetric analysis. The results showed that the surface of the modified inorganic particles was grafted by the MMA and that the grafting percentage was about 8.7%.     

Synthesis and Characterization of Poly(methyl methacrylate)-b-Polystyrene/TiO2 Nanocomposites Via Reversible Addition-Fragmentation Chain Transfer Polymerization

A diblock copolymer, poly(methyl methacrylate)-b-polystyrene (PMMA-b-PS), was grafted onto the surface of nano-titania (nano-TiO₂) successfully via reversible addition-fragmentation chain transfer (RAFT) polymerization. The surface of TiO₂ nanoparticles was modified initially by attaching dithioester groups to the surface using silane coupling agent 3-(chloropropyl)triethoxy silane and sodium ethyl xanthate. The polymerization of methyl methacrylate and styrene were then initiated and propagated on the TiO₂ surface by RAFT polymerization. The resulting composite nanoparticles were characterized by means of XPS, FT-IR, ¹H NMR and TGA. The results confirmed the successful grafting of poly(methyl methacrylate) (PMMA) and diblock copolymer chains onto the surface of TiO₂. The amount of PMMA grafted onto the TiO₂ surface increased with the polymerization time. Moreover, the kinetic studies revealed that the ln([M]₀/[M]), where [M]₀ is the initial and [M] is the time dependent monomer concentrations, increased linearly with the polymerization time, indicating the living characteristics of the RAFT polymerization.     

Preparation and characterization of a thermoresponsive gigaporous medium for high-speed protein chromatography

A high-speed thermoresponsive medium was developed by grafting poly(N-isopropylacrylamide-co-butyl methacrylate) (P(NIPAM-co-BMA)) brushes onto gigaporous polystyrene (PS) microspheres via surface-initiated atom transfer radical polymerization (ATRP) technique, which has strong mechanical strength, good chemical stability and high mass transfer rate for biomacromolecules. The gigaporous structure, surface chemical composition, static protein adsorption, and thermoresponsive chromatographic properties of prepared medium (PS–P(NIPAM-co-BMA)) were characterized in detail. Results showed that the PS microspheres were successfully grafted with P(NIPAM-co-BMA) brushes and that the gigaporous structure was robustly maintained. After grafting, the nonspecific adsorption of proteins on PS microspheres was greatly reduced. A column packed with PS–P(NIPAM-co-BMA) exhibited low backpressure and significant thermo-responsibility. By simply changing the column temperature, it was able to separate three model proteins at the mobile phase velocity up to 2167 cm h⁻¹. In conclusion, the thermoresponsive polymer brushes grafted gigaporous PS microspheres prepared by ATRP are very promising in ‘green’ high-speed preparative protein chromatography.