Bismuth and Bismuth-Chitosan modified electrodes for determination of two synthetic food colorants by net analyte signal standard addition method

In this paper, an electrochemical application of bismuth film modified glassy carbon electrode for azo-colorants determination was investigated. Bismuth-film electrode (BiFE) was prepared by ex-situ depositing of bismuth onto glassy carbon electrode. The plating potential was ?0.78 V (vs. SCE) in a solution of 0.15 mg mL^?1 Bi(III) and 0.05 mg mL^?1 KBr for 180 s. In the next step, a thin film of chitosan was deposited on the surface of bismuth modified glassy carbon electrode, thus the bismuth-chitosan thin film modified glassy carbon electrode (Bi-CHIT/GCE) was fabricated and compared with bare GCE and bismuth modified GCE. Azo-colorants such as Sunset Yellow and Carmoisine were determined on these electrodes by differential pulse voltammetry. Due to overlapping peaks of Sunset Yellow and Carmoisine, simultaneous determination of them is not possible, so net analyte signal standard addition method (NASSAM) was used for this determination. The results showed that coated chitosan can enhance the bismuth film sensitivity, improve the mechanical stability without caused contamination of surface electrode. The Bi-CHIT/GC electrode behaved linearly to Sunset Yellow and Carmoisine in the concentration range of 5×10^?6 to 2.38×10^?4 M and 1×10^?6 to 0.41×10^?4 M with a detection limit of 10 µM (4.52 µg mL^?1) and 10 µM (5.47 µg mL^?1), respectively      

Performance of Ex Situ Bismuth Film Rotating Disk Electrode in Trace Metal Analysis by Stripping Chronopotentiometry: Definition of the Depletion Regime and Optimization of Experimental Parameters

The potentiality of the ex situ deposited bismuth film electrode, allied to the rotation of a glassy carbon disk electrode (BiFE‐RDE), was exploited in trace metal analyses of lead(II) and cadmium(II) by stripping chronopotentiometry (SCP). A single BiFE (6.2 nm film thickness) can be used for a 1‐day term with no significant variation in the analytical signal. The limit of detection (3σ) for a deposition time of 40 s and an oxidation current of 15×10^?9 A was 1.5×10^?8 M for Pb(II) and 3.0×10^?8 M for Cd(II). BiFE‐RDE was successfully applied to the direct SCP determination of lead(II) in a fresh water certified material.     

Electrochemical determination of paraquat using a DNA-modified carbon ionic liquid electrode

Deoxyribonucleic acid (DNA) was electrochemically deposited on a carbon ionic liquid electrode to give a biosensor with excellent redox activity towards paraquat as shown by cyclic voltammetry and differential pulse voltammetry. Experimental conditions were optimized with respect to sensing paraquat by varying the electrochemical parameters, solution pH, and accumulation time of DNA. Under the optimized conditions, a linear relation exists between the reduction peak current and the concentration of paraquat in the range from 5?×?10^?8 mol L^?1 to 7?×?10^?5 mol L^?1, with a detection limit of 3.6?×?10^?9 mol L^?1. The utility of the method is illustrated by successful analysis of paraquat in spiked real water samples.

High Sensitivity and Reproducibility of a Bismuth/Poly(bromocresol purple) Film Modified Glassy Carbon Electrode for Determination of Trace Amount of Cadmium by Differential Pulse Anodic Stripping Voltammetry

This work described a novel type of bismuth/poly(bromocresol purple) film modified glassy carbon electrode (denoted as Bi/Poly(BCP)/GCE) for anodic stripping analysis of trace Cd²⁺. The Bi/Poly(BCP)/GCE was fabricated in situ by depositing simultaneously bismuth and cadmium by reduction at ?1.20 V on the poly(BCP) film using a differential pulse voltammetry. Under the optimum conditions, the anodic stripping peak current response increased linearly with the Cd²⁺ concentrations in a range of 2.0×10^?8–1.0×10^?7 M and 1.0×10^?7–6.0×10^?6 M in 0.1 M NaAc‐HAc buffer solution (pH 5.0) with the detection limit of 6.5×10^?9 M (S/N=3). The Bi/poly(BCP)/GCE performed good reproducibility and high sensitivity. Finally, this proposed method was successfully applied to determine the concentration of Cd²⁺ in water samples.     

Determination of ultratrace lead with bismuth film electrodes based on magneto-voltammetry

A novel method for the determination of Pb²⁺ with bismuth film electrodes (BFEs) based on magneto-voltammetry was investigated. In the presence of a 0.6?T external magnetic field, square wave voltammetry of Pb²⁺ was performed with BFEs. A high concentration of Fe³⁺ was added to the analytes to generate a large cathodic current during the preconcentration step. A Lorentz force from the flux of net current through the magnetic field resulted in convection. Then, more Pb²⁺ deposited onto the electrode and larger stripping peak currents were observed. BFEs that were prepared by simultaneously depositing the bismuth and Pb²⁺ on an electrode offered a mercury-free environment for this determination. This method exhibits a high sensitivity of 4.61?µA?µM^?1 for Pb²⁺ over the 1?×?10^?8 to 1?×?10^?6?M range. A detection limit as low as 8.5?×?10^?10?M was obtained with only 1-min preconcentration. The method was successfully applied to determine Pb²⁺ in real water samples.     

One‐Step Electrodeposited Carbon Nanotube/Zirconia/Myoglobin Film for Direct Electron Transfer and Electrocatalysis

A nanobiocomposite film consisted of zirconia, multiwalled carbon nanotubes (MWNTs) and Myoglobin (Mb) was electrochemically deposited on the electrode. Direct electron transfer for the immobilized Mb was realized and high electrocatalytic efficiency toward H₂O₂ was observed. The proposed biosensor via a simple one‐step electrodeposition method displayed a broader linear range and a lower detection limit for H₂O₂, as compared with those CNT or ZrO₂ based biosensor. The linear range is from 2 × 10^?6 M to 1 × 10^?3 M with the detection limit of 6 × 10^?7 M. The present strategy provides a simple and effective method to assemble CNT, ZrO₂ and enzyme nanohybrid on the electrode and expands the scope of CNT‐based electrochemical devices.     

Application of the Bismuth Film Electrode for Voltammetric Determination of Titanium Using Ti(IV)‐Oxalate‐Chlorate Catalytic System

The catalytic voltammetric protocol for the determination of titanium at a bismuth film electrode is presented. The method is based on the reduction of the Ti(IV)‐oxalate complex to Ti(III)‐oxalate in an acidic solution. It was proven that the addition of KClO₃ causes rapid oxidation of Ti(III)‐oxalate and, subsequently, an increase of the reduction peak current of Ti(IV) at the bismuth film electrode. Parameters that influence the Ti response, including the film preparation, solution pH, oxalate acid and chlorate concentrations, were optimized. The exploitation of the bismuth film electrode under the optimized conditions yielded a stable response for titanium, with high sensitivity (12.5 μA μM^?1), good precision (RSD=5.0%) and a low detection limit (1×10^?8 M).     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Nitrite at an In Situ Plated Bismuth Film Electrode

For the first time an in situ plated bismuth film electrode has been applied to catalytic adsorptive stripping voltammetry of cobalt in the presence of nitrite. At optimised conditions bismuth film was plated before each measurement for 30 s at ?1.0 V from a sample solution with the added supporting electrolyte and Bi(III) in the form of its complex with tartrate. The calibration graph for Co(II) for an accumulation time of 120 s was linear from 5×10^?10 to 1×10^?8 mol L^?1. The detection limit was 1.1×10^?10 mol L^?1. The proposed procedure was applied for Co(II) determination in certified water reference material.     

A Role of the Plating Regime in the Deposition of Bismuth Films onto a Carbon Paste Electrode. Microscopic Study

A microscopic study is presented based on observations of bismuth films deposited from various plating solutions and under different experimental conditions onto the carbon paste surface. Electrolytic plating of bismuth films was performed either as simulation of preconcentration in‐situ from a 0.2 M acetate buffer containing 5×10^?5 M Bi³⁺ (pH 4.25), or as external deposition from various plating solutions: 0.1 M acetate buffer with 5×10^?4 M Bi³⁺ (pH 4.50), 0.5 M HCl with either 0.001 M BiCl₃ or 0.005 M BiCl₃ , 0.5 M HCl+0.5 M KBr+0.005 M BiCl₃ , and 0.5 M HCl+0.5 M KI+0.005 M BiCl₃ (all pH≈0.5). Scanning electron microscopic images of the bismuth films showed a considerable variability in structure and compactness of the deposited layer in dependence on experimental conditions chosen such as the concentration of Bi(III) species, the total acidity of plating media, the stability of complexes of Bi(III) with halogenide anions or the deposition potential applied.     

Sensitive Determination of Folic Acid using a Solid Bismuth Microelectrode by Adsorptive Stripping Voltammetry

An adsorptive stripping voltammetric procedure of folic acid determination with the use of a new voltammetric sensor with a prolonged application‐solid bismuth microelectrode was described. The proposed microelectrode is characterized by more eco‐friendly properties as compared to in situ formed bismuth film electrodes due to the fact that bismuth ions are not needed as a component of supporting electrolyte for metal film plating. Furthermore the above mentioned fact simplifies and shortens a measurements procedure. Parameters affected folic acid determination were studied. After a procedure optimization the calibration graph was found to be linear in the range: 5×10^?10 to 1×10^?8 mol L^?1 (accumulation time: 120 s). The obtained detection limit of folic acid determination for accumulation time of 120 s was 1.8×10^?10 mol L^?1. Possible interferences deriving from a presence of other organic and surface active compounds were studied. The analysis of pharmaceutical preparation was positively performed following the presented procedure.     

Determination of Folic Acid at a Bismuth Film Electrode by Adsorptive Stripping Voltammetry

This article reports a new simple and sensitive method for the determination of folic acid by adsorptive stripping voltammetry. The method is based on the accumulation of folic acid at a bismuth film plated in situ on a glassy carbon substrate. In order to stabilize bismuth ions, sodium potassium tartrate was added to the supporting electrolyte. The bismuth film formation and folic acid accumulation conditions were optimized and measurements were carried without solution deaeration. The calibration graph was linear from 5 × 10^?10 to 2 × 10^?8 mole per liter with an accumulation time of 180 seconds with a limit of detection of 2 × 10^?10 mole per liter. The relative standard deviation for 5 × 10^?9 mole per liter of folic acid was 3.1 percent (n = 5). The method was successfully applied for determination of folic acid in pharmaceutical preparations.     

Electrooxidation and Amperometric Detection of Ascorbic Acid at GC Electrode Modified by Electropolymerization of N,N‐Dimethylaniline

The polymer film of N,N‐dimethylaniline (DMA) is deposited on the electrochemically pretreated glassy carbon (GC) electrode by continuous electrooxidation of the monomer. This poly N,N‐dimethylaniline (PDMA) film‐coated electrode can be used as an amperometric sensor of ascorbic acid (AA). The polymer film (thickness (?): 0.3±0.02 μm) having positive charge in its backbone attracts the anionic species AA. Thus, the anodic peak potential (350 mV vs. Ag|AgCl|NaCl_(sat)) for the oxidation of AA at the bare electrode is largely shifted to the negative value (150 mV) at this electrode. The PDMA film‐coated electrode is stable in acidic, alkaline and neutral media and can sense AA at different pH's. The diffusion coefficients of AA in solution (D) and in film (D_s) were estimated by rotating disk electrode voltammetry: D=(5.5±0.1)×10^?6 cm² s^?1 and D_s=(6.3±0.2)×10^?8, (6.0±0.2)×10^?8 and (4.7±0.2)×10^?8 cm² s^?1 for 0.5, 1.5 and 3.0 mM AA, respectively. A permeability of AA through the PDMA film was found to decrease with increasing the concentration of AA in the solution. In the chronoamperometry, the current response for the oxidation of AA at different times elapsed after potential‐step application is linearly increased with the increase in AA concentration in a wide range of its concentration from 25 μM to 1.65 mM. In the hydrodynamic amperometry, a successive addition of 10 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.178 μA cm^?2 μM^?1. So, the fouling of the electrode surface caused by the oxidized product of AA is markedly eliminated at this PDMA film‐coated electrode. A flow injection analysis based on the present electrode was performed to estimate the concentration of vitamin C in fruit juice.     

Carbon Paste Electrode Plated with Lead Film. Voltammetric Characteristics and Application in Adsorptive Stripping Voltammetry

A lead film plated in situ at a carbon paste support was tested as a novel, potential electrode for adsorptive stripping voltammetric determination of cobalt traces in an ammonia buffer solution. To show the practical applicability of the new electrode, a catalytic adsorptive Co system in a supporting electrolyte containing 0.1 M ammonia buffer, 5×10^?4 M nioxime and 0.25 M nitrite was selected and investigated as a model solution. Pb and Co ions were simultaneously accumulated in situ on the electrode surface: Pb ions electrochemically at ?1.3 V) and then at ?0.75 V, at which potential the Co(II)‐nioximate complex was also pre‐concentrated via adsorption. Instrumental parameters, such as the time of nucleation and formation of Pb film deposits, the time of accumulation of the Co‐nioxime complex at the PbF/CPE, and the procedures of electrode regeneration, were optimized to obtain good reproducibility and sensitivity of the Co response. The optimized procedure yields favorable and highly stable stripping responses with good precision (RSD=3% for a 5×10^?8 M Co) and good linearity (up to 5×10^?7 M, coefficient of determination, R=0.996). The detection limit was 4×10^?10 M Co (0.023 μg L^?1) for an accumulation time of 120 s. The method enables the determination of Co in the presence of high excesses of Ni or Zn. The voltammetric data were correlated with the structural characterization by scanning electron microscopy (SEM) and X‐ray fluorescence spectroscopy (XRF).     

Determination of Thallium in a Flow System by Anodic Stripping Voltammetry at a Bismuth Film Electrode

A procedure for trace thallium determination by anodic stripping voltammetry at a bismuth film electrode is presented. Measurements were performed in a flow system. The calibration graph was linear from 2×10^?9 to 3×10^?8 mol L^?1 for an accumulation time of 300 s. A detection limit for Tl⁺ following deposition time of 300 s was 6×10^?10 mol L^?1. The relative standard deviation at Tl⁺ concentration 2×10^?8 mol L^?1 was 3.9%. For determination of thallium in complex matrices the procedure for elimination of interferences from foreign ions exploiting anion exchange resin was proposed. The procedure proposed was validated by analysis of rain water certified reference material.     

Fabrication of Bismuth/Multi-walled Carbon Nanotube Composite Modified Glassy Carbon Electrode for Determination of Cobalt

A bismuth/multi‐walled carbon nanotube (Bi/MWNT) composite modified electrode for determination of cobalt by differential pulse adsorptive cathodic stripping voltammetry is described. The electrode is fabricated by potentiostatic pre‐plating bismuth film on an MWNT modified glassy carbon (GC) electrode. The Bi/MWNT composite modified electrode exhibits enhanced sensitivity for cobalt detection as compared with the bare GC, MWNT modified and bismuth film electrodes. Numerous key experimental parameters have been examined for optimum analytical performance of the proposed electrode. With an adsorptive accumulation of the Co(II)‐dimethylglyoxime complex at ?0.8 V for 200 s, the reduction peak current is proportional to the concentration of cobalt in the range of 4.0×10^?10?1.0×10^?7 mol/L with a lower detection limit of 8.1×10^?11 mol/L. The proposed method has been applied successfully to cobalt determination in seawater and lake water samples.     

Silver Doped Poly(L‐valine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Uric Acid,Ascorbic Acid and Dopamine

In this paper, a silver doped poly(L ‐valine) (Ag‐PLV) modified glassy carbon electrode (GCE) was fabricated through electrochemical immobilization and was used to electrochemically detect uric acid (UA), dopamine (DA) and ascorbic acid (AA) by linear sweep voltammetry. In pH 4.0 PBS, at a scan rate of 100 mV/s, the modified electrode gave three separated oxidation peaks at 591 mV, 399 mV and 161 mV for UA, DA and AA, respectively. The peak potential differences were 238 mV and 192 mV. The electrochemical behaviors of them at the modified electrode were explored in detail with cyclic voltammetry. Under the optimum conditions, the linear ranges were 3.0×10^?7 to 1.0×10^?5 M for UA, 5.0×10^?7 to 1.0×10^?5 M for DA and 1.0×10^?5 to 1.0×10^?3 M for AA, respectively. The method was successfully applied for simultaneous determination of UA, DA and AA in human urine samples.     

Novel preparation of electrically conducting poly (vinyl chloride) by photo-dehydrochlorination from poly (vinyl chloride)/polypyrrole composite film

Polypyrrole (PPy) was deposited electrochemically on a platinum plate from a nitric acid solution of pyrrole. The PVC/PPy composite film was finally obtained by casting poly(vinyl chloride) (PVC) onto the PPy electrode from a tetrahydrofuran solution of PVC. The prepared composite film was irradiated at 90°C with a low-pressure mercury lamp in the stream of hydrogen gas saturated with steam, and the PVC film was dehydrochlorinated, leading to the formation of conjugated polyene. The electrical conductivity (σ) of the PVC film in the irradiated composite film was reveled: σ=2.51 × 10^?5S cm^?1. By iodine doping, σ was further enhanced up to 5.04 X 10^?3 S cm^?1. The tensile strength of the irradiated composite film became larger than that of the original PVC film; i.e., the stress at break was: 461 (composite film); 401 kg cm^?2 (PVC). These results were brought about by the doping of radical species to the conjugated polyene. The anion, NO^?₃, doped during the electrodeposition of PPy was photodecomposed to generate radical NO₂ and this species was doped to the polyene, resulting in the formation of electrically conductive PVC and mechanically improved composite film. © 1994 John Wiley & Sons, Inc.     

Pure copper vs. mixed copper and palladium hexacyanoferrates for glucose biosensing applications

A glucose amperometric biosensor was developed. Glucose oxidase enzyme was immobilized by means of a Nafion membrane on glassy carbon modified with an electrochemically deposited mixed Cu and Pd hexacyanoferrate (CuPdHCF). According to the data provided by X-ray atomic spectroscopy measurements, this Cu- and Pd-based hexacyanoferrate is likely to be a mixture of single CuHCF and PdHCF pure phases. The biosensor performances were evaluated by recording the steady-state currents due to submillimolar additions of glucose to a potassium buffer solution (pH 5.5) and exploiting the electrocatalytic reduction of the enzymatically produced hydrogen peroxide. The CuPdHCF-based biosensor exhibited a sensitivity of 8.1?±?0.6 A M^?1 m^?2, a limit of detection of 1.4?×?10^?5 M, and a linear response range extending between 5?×?10^?5 and 4?×?10^?4 M, with a dynamic response range up to 4?×?10^?3 M glucose. Electrode sensitivity and signal stability resulted more satisfactory as compared to those of a CuHCF-based biosensor fabricated according to the same procedure. The selectivity was investigated through an interference study. The response to easily oxidizable species was found to be low enough to allow glucose determination in biological samples.     

Electrocatalytic Oxidation of Acyclovir on Poly(p‐Aminobenzene Sulfonic Acid) Film Modified Glassy Carbon Electrode

Acyclovir is an antiviral effective drug active compound. A glassy carbon electrode (GCE) was modified with an electropolymerized film of p‐aminobenzene sulfonic acid (p‐ABSA) in phosphate buffer solution (PBS). The polymer film‐modified electrode was used to electrochemically detect acyclovir. Polymer film showed excellent electrocatalytic activity for the oxidation of acyclovir. The anodic peak potential value of the acyclovir at the poly(p‐ABSA) modified glassy carbon electrode was 950 mV obtained by DPV. A linear calibration curve for DPV analysis was constructed in the acyclovir concentration range 2×10^?7–9×10^?6 mol L^?1. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 5.57×10^?8 and 1.85×10^?7 mol L^?1 respectively. The proposed method exhibits good recovery and reproducibility.     

Determination of Ultratrace Thallium(I) by Anodic Stripping Voltammetry at Bismuth Film Electrodes Following Double Deposition and Stripping Steps

The double deposition and stripping steps were proposed to increase the sensitivity in anodic stripping voltammetry of thallium(I). Two in situ plated bismuth film electrodes with drastically different surface areas were exploited for the measurements. Thallium was at first deposited at the electrode with a large surface area. As the deposition step at the large electrode was finished, the electrode was moved at a short distance to the small one. The thallium stripped from the large electrode was then accumulated at the second electrode. Taking into account the small volume of space between the electrodes, the concentration of Tl(I) between the electrodes was drastically higher than that in the bulk solution. The deposition step at the second electrode was performed from solution with a higher concentration of Tl(I) therefore the detection limit was lowered. The calibration graph was linear from 5×10^?11 to 5×10^?9 mol L^?1 following deposition time of 300 s at the first and the second electrode.