Evaluation of new high-frequency discharge lamps for atomic absorption and atomic fluorescence spectrometry of cadmium,lead and zinc

High-frequency discharge lamps with a hollow electrode are successfully utilized as the spectral line sources for atomic absorption and atomic fluorescence spectrometry of cadmium, lead and zinc. The sensitivities for atomic absorption spectrometry are superior to those obtained with commercially available hollow-cathode lamps by factors of 1.5 (Cd), 1.4 (Pb) and l.6 (Zn). Detection limits for non-dispersive atomic fluorescence spectrometry with graphite furnace atomization are 1 × 10^-13 g (Cd), 3 × 10^-11 g (Pb) and 2 × 10^-13 g (Zn). The linear analytical range covers over four (Cd, Zn) and three (Pb) decades of concentration above the detection limits.     

Poly(4-vinylpyridine-co-aniline)-modified electrode—synthesis, characterization, and application as cadmium(II) ion sensor

A poly(4-vinylpyridine-co-aniline) (poly(4VP-co-Ani))-based solid-state ion sensor for cadmium (Cd) was developed. This was obtained from studies done on a number of selected monomers electropolymerized onto a poly(4vinylpyridine) (P4VP)-modified graphite pencil rod, surface characterizing them and then analyzing their performances as a Cd(II) ion sensor. Among them, the membrane of poly(4VP-co-Ani) at a mole ratio of 0.05:0.15 was found to be the best. The fabricated poly(4VP-co-Ani) solid-state electrode had a linear response of 1?×?10^?6 to 1?×?10^?2?M Cd²⁺, slope of 29.4?±?0.5 mV decade^?1, detection limit of 7.94?×?10^?7?M Cd²⁺, and response time of 15 s at pH 4.5–8.5 with excellent selectivity. The sensor was operationally stable within a period of 3 months. The proposed sensor was tested for determination of Cd²⁺ in environmental, plant, and pharmaceutical samples. The analyses were comparable to the standard atomic absorption spectrophotometric method.     

Electrodeposition kinetics of Li—Al alloys on Al: Effect of the third component

During cathodic intercalation of lithium from a 1 M LiC1O₄ solution in a mixture of propylene carbonate and dimethoxyethane (1 : 1 volume ratio), the process is limited by the lithium diffusion in the solid phase, no matter the nature of the third component. The activation energies for the process during formation of α-phase and subsequent formation of intermetallic compound β-LiAl are close and increase from 20.4-22.9 to 27.3-28.3 kJ mol^-1 after introducing Zn, Pb, and Cd, respectively. The initial concentration of lithium defects decreases from 3.6 × 10^-2 to 1.14 × 10^-2 mol cm^-3 in the series Al(Pb) > Al(Zn) > Al(Cd) > Al(Cr) > Al(Co) > Al > Al(Mn). The diffusion coefficient for lithium in β-LiAl varies from 8.25 × 10^-9 to 3.43 × 10^-9 cm² s^-1 in initial aluminum modified by lead or chromium, respectively. The incorporation of the third component in the aluminum matrix presumably facilitates the formation of additional vacancies and defects that make the lithium diffusion easier     

Selektivitätssteigerung katalytischer bestimmungsverfahren—extraktionskataly-metrische molybdänbestimmung

To increase the selectivity of catalytic methods, a solvent extraction and catalytic determination have been combined. By means of the determination of molybdenum based on the catalytic oxidation of 1-naphthylamine by bromate, it is shown that by selection of a suitable extraction system the catalyst can be determined directly in the organic extract. The catalytic activity of different complexes of molybdenum was tested and for an analytical application the extraction of molybdenum as oxinate was chosen. The method enables molybdenum to be determined down to 2.7 × 10^?9M. The relative error of the determinations is 10%. 10^?4M V, 2 × 10^?4M Cr, 5 × 10^?5M W and 10^?2M Mn, Ni, Cu, Co, Fe, Mg, Zn, Cd, Al and Pb cause no interference. The method has been used for the determination of molybdenum in sea-water.     

Simultaneous Determination of Antimony and Lead in Gunshot Residue by Cathodic Adsorptive Stripping Voltammetric Methods

Differential pulse cathodic adsorptive stripping (DPCAdSV) and square wave cathodic adsorptive stripping (SWCAdSV) voltammetric methods were developed for the determination of antimony and lead in gunshot residues. Linear working ranges for DPCAdSV and SWCAdSV methods were (2.0×10^?9–5.0×10^?7) M and (2.0×10^?9–7.0×10^?7) M for antimony and 2.0×10^?9–3.0×10^?7 M (both methods) for lead. The detection of antimony limits were found to be 1.3×10^?9 M for DPCAdSV and 7.3×10^?10 M for SWCAdSV while the corresponding values for lead were 3.0×10^?9 M and 5.8×10^?10 M. Antimony and lead contents obtained by these methods in gunshot residues are in good agreement with those obtained by graphite furnace atomic absorption spectrometric method within a confidence limit of 95%.     

Electrothermal atomic absorption spectrometry of elements after electrochemical deposition on graphite electrodes

The application of electrochemical deposition on graphite rods for separation and preconcentration prior to electrothermal atomic absorption spectrometry (a.a.s.) is examined. The metals to be determined are electrolyzed onto a graphite rod which is tehn transferred to a cup atomizer for a.a.s. Although only some of the element present in the solution is deposited on the surface of the graphite rod, favorable preconcentration rates are obtained. The method was tested on the determination of cadmium in aqueous solution. The precision is satisfactory for concentrations down to 5 × 10^?8 g l^?1 cadmium, and the detection limit is 4 × 10^?9 g l^?1.     

Cauliflower‐like NiCo2O4−Zn/Al Layered Double Hydroxide Nanocomposite as an Efficient Electrochemical Sensing Platform for Selective Pyridoxine Detection

In the present study, a cauliflower‐like NiCo₂O₄?Zn/Al layered double hydroxide (NiCo₂O₄?Zn/Al LDH) nanocomposite was used as a novel electrode material for the sensitive and selective determination of pyridoxine (vitamin B₆). The structure and morphology of the as‐prepared nanocomposite were characterized by X‐ray diffraction (XRD), FT‐IR, field emission scanning electron microscopy (FESEM) and energy dispersive X‐ray spectroscopy (EDX). The NiCo₂O₄?Zn/Al LDH nanocomposite exhibited excellent electrocatalytic ability in the oxidation of pyridoxine, which could result from the synergistic effect of the two components. The developed sensor also provided a selective determination of pyridoxine in the presence of other species such as vitamins (B₁, B₂, B₁₂ and ascorbic acid), inorganic ions and biomolecules. The fabricated sensor showed a good linear response for pyridoxine over the concentration ranges 2×10^?7–2.0×10^?4 mol L^?1 with a low detection limit of 8.6×10^?8 mol L^?1. Finally, the proposed method was successfully applied for the determination of pyridoxine in commercial tablets and plasma samples with satisfactory results. Furthermore, this novel sensor displayed superior benefits in terms of stability, sensitivity, repeatability and cost. The present work aims to expand NiCo₂O₄ based nanocomposites to sensor fields and promote the development of pyridoxine sensors.     

Zerstörungsfreie aktivierungsanalytische Bestimmung von Mikro- und Ultramikromengen Indium in Reinstthallium und Thalliumverbindungen

Two non-destructive neutron activation methods has been described for the determination of indium in thallium metal and thallium compounds. The sensitivity of the first method based on^114mIn corresponds to 1×10^?6g (standard deviation 4,5–8%). The second method (by means of^116mIn) permits the determination of ultramicro amounts of indium up to 5×10^?11g with a standard deviation of 15%. The influence of many elements (such as Ga, Cu, Al, Cd, Zn, Pb, Ca, Mg, Bi, Fe) has been examined. The methods have been applied to the determination of indium in thallium metal, oxide, nitrate, sulphate and chloride. The data obtained agreed whith those of the spectrochemical determination.     

Atomic emission spectrographic determination of trace elements in environmental objects using a two-jet argon arc plasmatron

The effect of the main components (K, Na, Ca, Mg, Fe) on the atomic and ionic emission of trace elements Sr, Lu, V, Sc, Ti, Cr, Pb, Sn, Ni, Co, Bi, Mn, Pd, Zn, Be, Ba, Zr, Y, and La in atomic emission spectrometry with a two-jet argon arc plasmatron was studied to improve the accuracy of the quantitative multielement analysis of natural objects. It was shown that all of the studied macro elements to a certain extent enhance the analytical signal. The maximum enhancement was 2.5-fold. The effect of the matrix composition of the material is not strong and can easily be controlled by properly selecting the operational conditions of the formation of a plasma jet and bufferation, and also samples and reference elements. It was shown that a wide spectrum of trace elements can be quantitatively determined in various rocks, soils, and plant ashes with a relative standard deviation of 6–15% and detection limit of n × 10^?4 to n × 10^?6% using unified reference samples prepared synthetically.     

Cadmium Determination in Sedimented Dust by Atomic Emission Spectrometry With a New Radiofrequency Capacitively Coupled Plasma Source

ABSTRACT

A new radiofrequency capacitively coupled plasma source (r.f.CCP) was used for Cd determination in dust samples by atomic emission spectrometry. The plasma torch consists of a molybdenum tube electrode and one or two ring electrodes situated outside the quartz tube. Plasma was operated at 27.12 MHz, at low power (275 W) and low gas consumption (0.4 1 min^? argon flow). The choice of the optimum operating conditions for Cd determination in dust samples dissolved in acids and pneumatically nebulized is presented. The results obtained in such samples were compared with those obtained by flame atomic absorption spectrometry (FAAS). The matrix effect of NaCl and CaCl₂ on Cd emission was also studied depending of the plasma coupling system. The true limit of detection for Cd in dust sample by r.f.CCP-AES is 3 μg g^?1. Concentration of Cd higher than 10 μg g^?1 can be determined by the proposed method with a relative standard deviation within the range 5 - 10%. The recovery is 100 ± 10%.     

Separation of Cd(II) and Ni(II) ions by supported liquid membrane using D2EHPA/M2EHPA as mobile carrier

The separation of Cd(II) and Ni(II) ions was studied in an aqueous sulphate medium using supported liquid membrane (SLM). D2EHPA/M2EHPA was used as a mobile carrier, microporous hydrophobic PTFE film was used as a solid support for the liquid membrane, and the strip phase was sulphuric acid. The effects of different parameters such as feed concentration, carrier concentration, feed phase pH, and strip phase pH on the separation factor and flux of Cd(II) and Ni(II) ions were studied. The optimum values obtained to achieve the maximum flux were 5.0 for feed pH, 40 vol. % for D2EHPA/M2EHPA concentration in the membrane phase, 0.5 for strip pH, and 0.012 mass % for feed concentration. Under these optimum conditions, the flux values of Cd(II) and Ni(II) were 15.7 × 10^?7 kg m^?2 s^?1 and 2.6 × 10^?7 kg m^?2 s^?1, respectively. The separation factors of Cd(II) over Ni(II) were studied under different experimental conditions. At a carrier concentration of 10 vol. % and feed concentration of 0.012 mass %, the maximum value of 185.1 was obtained for the separation factor of Cd(II) over Ni(II). After 24 h, the percentages of the extracted Cd(II) and Ni(II) were 83.3 % and 0.45 %, respectively.     

Electrochemical Investigations of the Anticancer Drug Idarubicin Using Multiwalled Carbon Nanotubes Modified Glassy Carbon and Pyrolytic Graphite Electrodes

The effect of surface modifications on the electrochemical behavior of the anticancer drug idarubicin was studied at multiwalled carbon nanotubes modified glassy carbon and edge plane pyrolytic graphite electrodes. The surface morphology of the modified electrodes was characterized by scanning electron microscopy. The modified electrodes were constructed for the determination of idarubicin using adsorptive stripping differential pulse voltammetry. The experimental parameters such as supporting electrolyte, pH, accumulation time and potential, amount of carbon nanotubes for the sensitive assay of idarubicin were studied as details. Under the optimized conditions, idarubicin gave a linear response in the range 9.36×10^?8–1.87×10^?6 M for modified glassy carbon and 9.36×10^?8–9.36×10^?7 M for modified edge plane pyrolytic graphite electrodes. The detection limits were found as 1.87×10^?8 M and 3.75×10^?8 M based on modified glassy carbon and edge plane pyrolytic graphite electrodes, respectively. Interfering species such as ascorbic acid, dopamine, and aspirin showed no interference with the selective determination of idarubicin. The analyzing method was fully validated and successfully applied for the determination of idarubicin in its pharmaceutical dosage form. The possible oxidation mechanism of idarubicin was also discussed. The results revealed that the modified electrodes showed an obvious electrocatalytic activity toward the oxidation of idarubicin by a remarkable enhancement in the current response compared with bare electrodes.     

Surface characterization by underpotential deposition: Lead on gold surfaces

The kinetics of chelation of Pb(II), Zn(II) and Cd(II) with the ligand EDTA have been followed at the realistic trace concentration level 10^?8–10^?7M for both reactants in sea water and model solutions of its major salinity components by differential pulse stripping voltammetry. In this manner the specific influences of the salinity components on the formation rate constants [having in sea water for PbEDTA the order of 3×10³ and for the EDTA chelates of Zn(II) and Cd(II) of 3×10² l M^?1 s^?1] could be determined. The measurements emphasize the pronounced specific influences of Ca(II) on the kinetics and course of the trace metal chelation in media where this alkaline earth ion is present in substantial excess to organic chelating agents. The experiments with EDTA are to be regarded as a close simulation of the chelation processes occurring for the trace metals studied by components with suitable chelation power of dissolved organic matter (DOM) in the sea and the resulting conclusions on the mechanism are thus of general significance.     

4-Hydroxy-3,5-pyridinedicarboxylic Acids: Synthesis,Complexation Properties Towards Fe(III), Al(III), Cu(II), Zn(II), Human Serum Albumin,and Cellular Toxicity

4-hydroxy-3,5-pyridinedicarboxylic acid (DQ58) and 4-hydroxy-1-methyl-3,5-pyridinedicarboxylic acid (DQ71508) have been synthesized, and their Fe(III), Al(III), Cu(II), and Zn(II) coordination properties have been studied by potentiometry, UV–Vis spectroscopy (in the case of Fe(III), Al(III), Cu(II)), ¹H-NMR (for Al(III)) and EPR (for Cu(II)). The thermodynamic results were used to model the extent of the toxic metal ions decorporation (Fe(III) or Al(III)) in the presence of the essential metal ions (Cu(II) or Zn(II)). DQ58 and DQ71508 were demonstrated to interact with human serum albumin (HSA), which is assumed to be the main serum transporter of the chelators, and binding constants have been obtained by ultrafiltration. IC₅₀ values of 5.185 × 10^?3 and 1.033 × 10^?3 mol·L^?1 were collected after 24 and 48 h of treatment with DQ71508 towards human embryonic kidney HEK-293 cells, demonstrating the relatively low cytotoxicity of this compound. According to these results, both DQ58 and DQ71508 seem to be potential candidates for Fe chelation therapy, and DQ58 is a better Fe(III) chelator than DQ71508.     

Trace Elements in Pleurotus Ostreatus,P. Eryngii,and P. Nebrodensis Mushrooms Cultivated on Various Agricultural By-Products

Abstract

Mushrooms are efficient accumulators of essential and toxic elements. Although oyster (Pleurotus spp.) mushrooms are widely commercialized and consumed, few data exist regarding trace elements content and bioaccumulation in cultivated P. ostreatus and P. eryngii, while no data are available for P. nebrodensis. The contents of Al, As, Ba, Cd, Co, Cr, Cs, Cu, Fe, K, Mn, Na, Ni, Pb, Rb, Sr, V, and Zn were monitored using inductively coupled plasma-mass spectrometry (ICP-MS) and atomic emission spectrometry (AES) in P. ostreatus, P. eryngii, and P. nebrodensis mushrooms and their cultivation substrates that include wheat straw (WHS), grape marc (GMC), olive leaves (OLV), and two-phase olive mill wastes (OMW), separately or in mixtures. Bioaccumulation factors (BAFs) less than 0.3 were obtained for Al, Ba, Co, Cr, Fe, Mn, Ni, Pb, Sr, and V; BAFs exceeding 1 for K?>?Zn?>?Cd?>?Cr?>?Rb?>?As, while the BAFs for Na were less 0.7. Mushrooms grown on OLV and OMW presented lower BAFs than those grown on WHS and GMC for all elements except for K, Cd, and Cu. P. ostreatus was an effective accumulator for Cr, Fe, and Zn; P. eryngii for Al, Cs, Ni, and V; and P. nebrodensis for As and Cd. The estimated daily intakes (μg kg^?1 body weight) from mushroom consumption were less than 0.010 for As, Cd, Co, Cs, Pb, and V, 0.010–0.10 for Ba, Cr, Ni, and Sr, 0.10–5.0 for Al, Cu, Fe, Mn, Rb, and Zn, 65–83 for Na, and 858–1030 for K. Overall, the mushrooms studied provide significant amounts of K, adequate amounts of Mn and Zn and low amounts of Na and toxic elements.     

Anregung von Spektren durch niederenergetischen Elektronenstoβ mit Anwendung als Lichtquelle für Spektralanalyse

Detection limits of atomic absorption spectroscopy (AAS) and atomic fluorescence spectroscopy (AFS) have been improved by the use of a King furnace. In atomic emission spectroscopy, however, the King furnace was hitherto used only in connection with thermal or RF excitation.The object of this work was to combine the advantages of the King furnace and the advantages of excitation by electron impact for AES. A light source based on a work by Ritschl in 1932 was built. The device consists of a King furnace for sample evaporation. Excitation of atoms is achieved by separate production and acceleration of electrons.The spectrochemical application of this excitation method was tested with Cd, Mg, Hg and B. Detection limits were measured and compared with those attained by other methods. Detection limits are better than those of comparable AES methods using thermal light sources. They compete favourably with those of AAS and AFS using a graphite crucible. The detection limit of Cd, for example, is 3·10^?13 g.The source was applied to determine traces in spectral graphite and to study the transport of material between the electrodes in high-voltage spark.     

Summary of ISO/TC 201 Standard: XIX ISO 17331:2004—Surface chemical analysis—Chemical methods for the collection of elements from the surface of silicon‐wafer working reference materials and their determination by total‐reflection x‐ray fluorescence (TXRF) spectroscopy

This international standard specifies chemical methods for the collection of iron and/or nickel from the surface of silicon‐wafer working reference materials by the vapour‐phase decomposition method or the direct acid droplet decomposition method. The determination of the elements collected may be carried out by total‐reflection x‐ray fluorescence spectroscopy, as well as by graphite‐furnace atomic absorption spectroscopy or inductively coupled plasma mass spectroscopy. This international standard applies to iron and/or nickel atomic surface densities from 6 × 10⁹ to 5 × 10¹¹ atoms cm^?2. Copyright © 2005 John Wiley & Sons, Ltd.     

Cyclohexane-1, 3-Dione bis (4-Methylthiosemicarbazone) as a Spectrophotometric Reagent for the Determination of Zn (II)

Abstract

The spectrophotometric study of reddish cyclohexane-1, 3-dione bis (4-methylthiosemicarbazone)-Zn(II) was made in dimethylformamide-water solution (λ_max= 475 nm, ∑ = 3.3×10⁴ 1.mole^?1. cm^?1. Sandell sensitivity = 2×10^?2 μg Zn(II).cm^?2, stoichiometry 1:1, and apparent stability constant 6.1×10⁴). A new method for the spectrophotometric determination of Zn(II) is proposed for concentrations between 0.1 and 2.5 ppm. The relative error (95% confidence level) is 0.7% for 1.0 pprn of Zn(II).

The extraction with ethylacetate of the reddish complex was also studied spectrophotometrically (λ_max = 493 nm, ∑ in organic phase = 4.8×10⁴ 1.mole^?1.cm. Sandell sensitivity = 3.4×10^?4 μg Zn(II).cm^?2, stoichiometry 1:1, apparent extraction constant 1.4×10⁴). A new method for the extraction-spectrophotometric determination of Zn(II) is proposed for concentrations, in aqueous phase, between 0.02 and 0.30 ppm. The relative error (95% confidence level) is 1.0% for 0.15 pprn of Zn(II).     

DFT and kinetics study of O/O2 mixtures reacting over a graphite (0001) basal surface

Spin-polarized density functional calculations were used to investigate the interaction of atomic and molecular oxygen on the basal graphite surface at several atomic coverages. Two carbon layers were enough to represent the graphite surface. Oxygen atoms bind mainly over C?CC bridge sites forming an epoxide-like structure with a two carbon puckering and with adsorption energies in the 0.95?C1.28?eV range, depending on the atomic coverage. Molecular oxygen only shows a very weak physisorption. Atomic adsorption and diffusion along with atomic recombination via Eley?CRideal and Langmuir?CHinshelwood mechanisms were studied. All surfaces processes were activated with energy barriers that decreased for lower atomic coverages. Relaxation effects were non-negligible. A microkinetic model with six elementary surface processes was proposed to see the overall behaviour of several initial O/O₂ mixtures flowing over a graphite surface at 300?C1,000?K. Thermal rate constants were derived from Density Functional Theory data and standard Transition State Theory. A very low steady-state atomic coverage (??_???<?0.5%) was predicted, and also very low atomic recombination coefficients were observed (??_O?<?5?×?10^?4). The Eley?CRideal together with the adsorption and desorption processes was much more important than the Langmuir?CHinshelwood reaction.     

Advances with tungsten coil atomizers: Continuum source atomic absorption and emission spectrometry

Two new tungsten coil spectrometers are described: a continuum source tungsten coil atomic absorption spectrometer and a tungsten coil atomic emission spectrometer. Both devices use a 150 W tungsten coil extracted from a slide projector bulb. The power is provided by a computer-controlled, solid state, constant current 0–10 A supply. The heart of the optical system is a high-resolution spectrometer with a multi-channel detector. The continuum source system employs xenon or deuterium lamps, and is capable of multi-element analyses of complex samples like engine oil, urine, and polluted water. Spiked engine oil samples give mean percent recoveries of 98 ± 9, 104 ± 9, and 93 ± 0.8 for Al, V, and Ni, respectively. Copper, Zn, and Cd are determined in urine samples; while Cd, Co, Yb, and Sr are determined in water samples. Detection limits for Cd, Zn, Cu, Yb, Sr, and Co are: 8, 40, 1, 4, 1, and 4 μg l^− 1. The technique of tungsten coil atomic emission spectrometry using a 150 W commercial projector bulb is reported for the first time. Calcium, Ba, and Sr are determined with detection limits of 0.01, 0.5, and 0.1 μg l^− 1. Relative standard deviations are lower than 10% in each case, and Sr is determined in two water standard reference materials.