Formation of a liquid organic ion associate in aqueous solution and its application to the GF-AAS determination of trace cadmium in environmental water as a complex with 2-(5-bromo-2-pyridylazo)-5-(N-propyl-N-sulfopropylamino)phenol

The formation of a liquid organic ion associate in an aqueous sample was applied to the concentration and determination of cadmium in environmental water samples. Cadmium was converted into a complex with 2-(5-bromo-2-pyridylazo)-5-(N-propyl-N-sulfopropylamino)phenol (5-Br-PAPS) in a 40-mL sample solution, and was extracted into a liquid ion associate of phenolsulfonate and benzethonium during phase formation. More than 400-fold enrichment was easily attained by this technique, because the volume of the liquid organic phase formed was very small, ca. 2 microL. After dilution of the organic phase with a small volume of 2-methoxyethanol, the cadmium in the solution was determined by GF-AAS. The detection limit was 0.09 ng/L (3sigma(b)). This method was applied to the determination of cadmium in river water and seawater.     

Adsorptive voltammetry of 2-(5-bromo-2-pyridyl)azo-5-[N-n-propyl-N-(3-sulfopropyl)amino]phenol on a carbon paste electrode in the presence of organic cations and polycation.

The adsorption of ion-association complexes on a carbon paste electrode (CPE) was investigated by cyclic voltammetry using an electroactive hydrophobic anion probe. The redox reactions of 2-(5-bromo-2-pyridyl)azo-5-[N-n-propyl-N-(3-sulfopropyl)amino]phenol (5-Br-PAPS), the analytical probe, were irreversible. The reduction of the azo group and the oxidation of the phenol were observed at -0.1 V and 0.9 V vs. SCE, respectively, in a 0.1 mol L(-1) H(2)SO(4) solution. The peak currents for the redox reaction increased with the concentration of the cationic surfactant and the accumulation time. The increase in the ratio of the peak current to the concentration of cationic surfactants was proportional to the hydrophobicity. The peak current for 5-Br-PAPS also increased when a polycation, polyhexamethylene biguanide hydrochloride, was added and was strongly dependent on the ionic strength and pH, in contrast to cationic surfactants.     

2-(3,5-二溴-2-吡啶偶氮)-5-二乙氨基苯酚作络合滴定指示剂连续测定铁和铝

对2-(3,5-二溴-2-吡啶偶氮)-5-二乙氨基苯酚作铁(Ⅲ),铜(Ⅱ)的配位滴定指示剂进行了研究.在pH1.8～2.0时用EDTA标准溶液滴定铁(Ⅲ).在滴定铁(Ⅲ)后的溶液中,加入对铝过量的EDTA标准溶液,在pH3.8～4.0煮沸下,铝(Ⅲ)与EDTA生成稳定的络合物,过量的EDTA用硫酸铜标准溶液滴定,从而测定铝(Ⅲ).     

A novel fluorescence reagent, 10-hydroxybenzo[h]quinoline-7-sulfonate, for selective determination of beryllium(II) ion at pg cm(-3) levels.

A facile method has been developed for the highly sensitive and selective determination of ultratrace Be(II) ion using a new fluorimetric reagent, 10-hydroxybenzo[h]quinoline-7-sulfonate (HBQS), under extremely alkaline conditions, at pH 12.0. This reagent is quite suitable for the very small ion, Be(II), to form a 6-membered chelate ring, compatible with a high fluorescence yield. The stoichiometry of the chelate is 1:1 for Be-HBQS at pH 12.0. The calibration graph gave a wide linear dynamic range, 2-100 nmol dm(-3) of Be(II) ion with the detection limit (3s blank) of 0.52 nmol dm(-3), or 4.7 pg cm(-3). The excellent sensitivity and toughness toward the matrix influence were demonstrated using the artificial sample solutions for air-dust. Coupled with the simple masking procedure using EDTA, the method enables one to determine Be(II) ion at nanomolar levels in the presence of metals at the natural abundance levels in air-dust samples, typically Al, Ca, Cu, Fe, Mg, Pb, and Zn at 130, 150, 1.0, 70, 33, 3.0, and 8.0 micromol dm(-3), respectively, in the final solution. The proposed method was successfully applied to the determination of Be in urban air.     

Complexometric titration of thallium(III), by use of 4-amino-5-mercapto-3-propyl-1,2,4-triazole as replacing reagent

A simple and selective EDTA method using a masking and demasking technique is proposed for the determination of thallium(III). The thallium is complexed with excess of EDTA, the surplus being back-titrated (pH 5-6, hexamine buffer) with zinc sulphate solution (Xylenol Orange as indicator). 4-Amino-5-mercapto-3-propyl-1,2,4-triazole is then added and the mixture heated on a water-bath for 5-10 min to displace EDTA from its thallium complex. The EDTA liberated is titrated with zinc sulphate solution. Reproducible and accurate results are obtained in the range 5-75 mg of thallium with both the relative error and coefficient of variation not exceeding 0.4%.     

6-Chloro-3-hydroxy-2-(5'-methylfuryl)-4H-chromene-4-one as an analytical reagent for micro determination of molybdenum(VI).

6-Chloro-3-hydroxy-2-(5'-methylfuryl)-4H-chromene-4-one (CHMFC) has been used as an analytical reagent for the spectrophotometric determination of molybdenum. Molybdenum(VI) in the presence of several cations, anions and complexing agents forms a yellow 1:2 complex with CHMFC. The complex is quantitatively extractable into 1,2-dichloroethane from 1 mol dm(-3) acetic acid medium and is stable for more than 6 h. The complex shows an absorption maximum at 438 nm with a molar absorptivity of 5.36 x 10(4) dm3 mol(-1) cm(-1) and Sandell's sensitivity equal to 0.0017 microg Mo cm(-2). The method obeys Beer's law up to 1.9 microg Mo ml(-1). The relative standard deviations are 0.2% for solutions and 0.5-1.5% for solid samples. The method is simple, selective, precise and rapid, and has been satisfactorily applied to the micro determination of molybdenum in various synthetic and standard samples.     

2-(5-溴-2吡啶偶氮)-5-二乙氨基酚显现人体皮肤表面镀锌工具遗留印迹

研究2-(5-溴-2吡啶偶氮)-5-二乙氨基酚(5-Br-PADAP)试剂显现镀锌工具遗留印迹的方法。 考察接触时间、时间间隔、试剂浓度、是否洗手等因素对印迹强度及分辨率的影响,并对该方法的可靠性进行验证。 实验结果表明,试剂浓度1 g/L、接触时间10 s以上,间隔时间不超过4 h条件下,均能显出较好的印迹。 该方法可以灵敏地显现镀锌工具遗留印迹,对非铁金属工具遗留印迹检测进行了很好地补充。     

Spectrophotometric determination of cadmium(II) using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

The complex of cadmium with the reagent 2-(-5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been studied. The composition, stability constant, and free energy change of formation of the complex have been determined. A sensitive spectrophotometric method for the determination of cadmium has been developed and applied for a range of concentration of 0.4–4.0 μg/ml cadmium using the complex Cd-5-Br-PADAP. The optimum conditions for maximum sensitivity of determination such as standing time, pH, wavelength, and order of addition have been determined. The effect of foreign ions on this method has been also studied.     

Extraction and spectrophotometric determination of zinc in coal fly ash and pond sediments with 2-[2-(3,5-dibromopyridyl)azo]-5-dimethylaminobenzoic acid

An extraction-spectrophotometric method is described for the determination of traces of zinc with 2-[2-(3,5-dibromopyridyl)azo]-5-dimethylaminobenzoic acid. The reagent forms a stable, blue 1:2 zinc/reagent complex that can be extracted into chloroform. The apparent molar absorptivity of the zinc(II) complex is 1.26 × 10⁵ l mol^?1 cm^?1 at 610 nm in chloroform. The reagent is relatively selective; interferences from cobalt, copper and nickel can be masked with dimethylglyoxime and aluminium and iron with a mixture of sodium fluoride and triethanolamine. The method is applied to the determination of zinc in coal fly ash and pond sediments with good precision and accuracy.     

4-(3,5-Dichloro-2-pyridylazo)-1-3-diaminobenzene-graphite paste electrode for end-point detection in the automatic potentiometric titration of zinc(II) with EDTA

A simple and sensitive potentiometric sensor for end-point detection in the automatic titration of Zn(II) with EDTA was prepared and studied. The sensor was based on a conventional carbon paste which was mixed during preparation with 4-(3,5-dichloro-2-pyridil-azo)-1,3-diaminobenzene (3,5-Cl2PADAB). pH effects, buffer concentration, reagent content into carbon paste and the presence of foreign salts on the electrode response were studied. Titration curves with sharp end-point breaks were obtained in Zn(II) concentration range from 0.5 to 6550 ppm. The electrode was easily made and with very inexpensive materials. A titrimetric method for the determination of zinc in insulin by automatic potentiometric end-point detection is described. It was applied to the determination of the metal in two commercial pharmaceutical preparations. The results were in good agreement with those obtained by the U.S. Pharmacopeia standard method.     

Extraction and sensitive spectrophotometric determination of ytterbium with 2-(3,5-dichloro-2-pyridylazo)-5-dimethylaminophenol

The operating conditions for the absorptiometric determination of Yb(III) with the reagent 2-(3,5-dichloro-2-pyridylazo)-5-dimethylaminophenol (3,5-diClDMPAP) by a liquid—liquid extraction technique are presented. The complex yields a molar absorptivity of 1.54 × 10⁵l.mole⁻¹.cm⁻¹ (λ_max = 588 nm) and an optimum concentration range of 0.025–1.360n mg/l., at pH = 10. The method developed has been applied to the determination of Yb(III) in synthetic and concrete mixtures.     

Optimization of a flow injection system with amperometric detection for arsenic determination.

A selective and sensitive analytical procedure for rapid arsenic determination by gas-diffusion flow injection analysis with amperometric detection was developed. The method is based on the arsenite reduction by NaBH(4). Derived arsine diffuses through a PTF membrane into the acceptor flow stream and is amperometrically determined on a platinum working electrode. The limit of detection (3 sigma) at room temperature was 5 microg/dm(3) of As(III). The relative standard deviation for a 1 mg/dm(3) As(III) standard was 1.96% for six repetitive injections. Arsenic(V) was determined after its prereduction with potassium iodide. Arsenic determination was not interferred with by 1 mg/dm(3) Sb(III), 5 mg/dm(3) Sn(II), 10 mg/dm(3) Se(IV), 1 mg/dm(3) As(V), 1 mg/dm(3) hydrasine, 1 mg/dm(3) Fe(II) or 0.5 mg/dm(3) Fe(III) solution. The throughput of this method was 60 analyses per hour. This method was successfully applied to arsenic determination in some power plant waste water samples.     

Simultaneous spectrophotometric determination of uranium and thorium by flow injection analysis using selective masking.

A flow injection system for the simultaneous determination of uranium and thorium has been developed by using selective masking and a spectrophotometric detector with two flow cells aligned with the same optical path. The injected sample solution was first mixed with a reagent solution containing Chromazurol S (CAS) and cetyltrimethylammonium chloride (CTMAC), and the total absorbance of uranium- and thorium-CAS complexes was measured in the first flow cell at 620 nm. The sample stream was then mixed with an EDTA solution in order to convert the thorium-CAS complex to a thorium-EDTA complex, and the absorbance of the uranium-CAS complex was measured in the second flow cell. The detection limits were 10 microg dm(-3) for uranium and 7 microg dm(-3) for thorium. The calibration graphs were linear (r < 0.9998) at least over the ranges of 0.1 to 10 mg dm(-3) for uranium and 0.08 to 8 mg dm(-3) for thorium. The RSDs were less than 1.5% (n = 3) in the calibration range. Uranium and thorium of up to the 6-fold concentration to each other could be determined in admixtures with relative errors of less than 3.3%. The sample throughput was 24 per hour. The proposed system was successfully applied to the analysis of a uranium-thorium ore mock solution by coupling with anion-exchange in a magnesium nitrate medium to eliminate interference from coexisting elements.     

Extraction-spectrophotometric determination of trace iron (II) in sea water with 2-[2-(3,5-dibromopyridyl)azo]-5-diethylaminobenzoic acid

An extraction-spectrophotometric method is described for the determination of traces of iron(II) with 2-[2-(3,5-dibromopyridyl)azo]-5-diethyl-aminobenzoic acid. The reagent forms a stable and blue 12 iron/reagent complex that can be extracted into chloroform. The apparent molar absorptivity of the iron(II) complex is 1.09 × 10⁵ 1 mol^–1 cm^–1 at 624 nm in chloroform. The reagent is relatively selective; interferences from cobalt, copper, nickel and vanadium can be removed by using dimethylglyoxime and EDTA. The method is applied to the determination of iron (II) in sea water and aluminium alloys with good precision and accuracy.     

Flow injection spectrophotometric determination of sub-mg dm(-3) silver(I) in a strongly acidic solution containing concentrated copper(II) using a pyridylazo reagent

A novel spectrophotometric flow injection method for determination of silver(I) in a strongly acidic solution containing concentrated copper(II) was developed using a coloring ligand, 4-(3,5-dibromo-2-pyridylazo)-N-ethyl-N-(3-sulfopropyl)aniline (3,5-diBr-PAESA). The method was first investigated by batch method. The interference from copper(II) chelate could be eliminated by the masking effect of EDTA. By utilizing the large formation constant (K = 12.3) of AgBr, one could determine silver(I) as a decrease of absorption by silver(I) chelate due to formation of AgBr by addition of KBr. Based on the results of batch experiments, two types of flow injection analysis (FIA) systems were constructed. Sub-mg dm(-3) determination of silver(I) was attained without interference from excess copper(II). The proposed method was successfully applied to determination of silver in a copper plating solution used in a plant to manufacture copper printed circuit boards, where the concentration of silver was critically important in the process control.     

Kinetic determination of trace cobalt(II) by visual autocatalytic indication

A highly sensitive and simple visual autocatalytic method has been developed for the determination of trace cobalt. The cobalt ion released by the oxidative decomposition of inert bis[2-(5-bromo-2-pyridylazo)-5-(N-propyl-N-sulfopropyl-amino-phenolato] cobaltate (Co(III)-5-Br-PAPS) with peroxomonosulfate acts as a catalyst for the oxidative degradation of the complex. Thus a definite time lapse of degradation is observed by the sudden disappearance of colored Co(III) complexes. The degradation time varies inversely with the logarithm of the initial concentration of cobalt(II). The determination range of cobalt(II) was from 3x10(-9) to 2x10(-7) M in the presence of 5x10(-6) M of 5-Br-PAPS. The relative standard deviation of the spot size method (10 mul) was 3.5% at 1x10(-7) M cobalt(II). This autocatalytic indicator reaction system has been successfully applied for the visual determination of urinary cobalt.     

5—（2—苯并噻唑偶氮）—8—氨基喹啉作为镍的光度分析试剂及应用研究

研究了新试剂 5- (2 -苯并噻唑偶氮 ) - 8-氨基喹啉与镍的显色反应。在弱碱性介质中 ,阳离子表面活性剂溴化十六烷基三甲基铵存在下 ,试剂与镍形成 3∶ 1的蓝色配合物 ,其最大吸收波长位于 61 0 nm处 ,表观摩尔吸光系数为 1 .2 6× 1 0 5L· mol-1· cm-1,镍的浓度在 0～ 8.0μg/2 5ml范围内 ,符合比耳定律。应用于铝合金中微量镍的测定 ,获得了满意的结果。     

Determination of transition metal ions in tobacco as their 2-(2-quinolinylazo)-5-dimethylaminophenol derivatives using reversed-phase liquid chromatography with UV-VIS detection

This paper reports the utilization of solid-phase extraction and the reversed-phase high-performance liquid chromatography for the determination of six important transition metal ions: iron, cobalt, nickel, copper, zinc and manganese in tobacco with 2-(2-quinolinylazo)-5-dimethylaminophenol (QADMAP) as chelating reagent. Iron, cobalt, nickel, copper, zinc and manganese ions react with QADMAP to form colored chelates in the medium of acetic acid-sodium acetate buffer solution (pH 4.0). These chelates can be enriched by solid-phase extraction with Waters Sep-Pak-C18 cartridge, and eluted the retained chelates from cartridge with tetrahydrofuran. The chelates were separated on a Waters Nova-Pak-C18 column (150x3.9 mm, 5 microm) by gradient elution with methanol (containing 0.5% of acetic acid) and 0.05 mol/l pH 4.0 acetic acid-sodium acetate buffer solution as mobile phase at a flow-rate of 0.5 ml/min. The detection limits of iron, cobalt, nickel, copper, zinc and manganese are 10, 12, 8, 13, 17 and 22 ng/l, respectively. This method had been applied to the determination of iron, cobalt, nickel, copper, zinc and manganese in tobacco with good results.     

Spectrophotometric determination of sulfide in the presence of sulfite and thiosulfate via the precipitation of bismuth(III) sulfide.

A photometric method has been developed for the determination of sulfide at 10(-5) mol dm(-3) levels, which is based on the reaction of sulfide with a given excess amount of bismuth(III) to form a precipitate of bismuth(III) sulfide and on the spectrophotometric measurement of the residual bismuth(III) at 335 nm after extracting with bismuthiol II reagent from an aqueous solution containing acetate buffer into benzene. The presence of sulfite and thiosulfate up to 0.002 mol dm(-3) did not cause any interference in the determination of sulfide, because both sulfite and thiosulfate do not produce any precipitate with bismuth(III). A linear calibration plot with a negative slope was obtained for sulfide over the range of 5.00 x 10(-7) - 3.00 x 10(-5) mol dm(-3) (16.0 - 960 ppb). An experimental calibration plot was in accord with the theoretical plot, taking into account the known excess of bismuth(III), showing that the reaction of sulfide with bismuth(III) proceeded to completion. The relative standard deviation of results from 10 replicate determinations of standard sulfide (2.00 x 10(-5) mol dm(-3)) was 0.44%. The proposed method was successfully applied to the determination of sulfide in hotspring water samples without any pretreatment.     

2-(5-硝基-2-吡啶偶氮)-5-二甲氨基苯胺与铑显色反应的研究及应用

本文报道了以新试剂2-(5-硝基-2吡啶偶氮)-5-二甲氨基苯胺(5-NO_2-PADMA)作分光光度法测定铑的新体系.结果表明,在 PH=5.25～6.75范围内,铑与 5-NO_2-PADMA形成 1:1的紫红色络合物,其 λ_(max)在 525 nm处,该络合物在 1.8mol/L的盐酸溶液中转变为绿兰色,其最大吸收峰位于620nm处,表观摩尔吸光系数为1.39×10～5L·mol～1·cm～1.反应具有良好的选择性,常见金属离子在一定范围内无干扰.铑含量为0～0.56μg/mL范围内遵守比耳定律.所拟方法操作简便,灵敏度高,用于催化剂中微量铑的测定,结果满意.