Phase composition and conductivity of La1 ? x Sr x ScO3 ? α (x = 0.01?0.20) under oxidative conditions

The phase composition was studied and overall conductivity of oxides La_{1 ? x} Sr _x ScO_{3 ? ??} (x = 0.01?0.20) was measured as dependent on air humidity (pH₂O = 0.04?2.35 kPa) in the temperature range from 100 to 900°C. The samples were synthesized in air at 1600°C. They are single-phase, with a perovskitetype structure with orthorhombic distortions and the density of 94?C99%. The conductivity measurements were carried out using the impedance technique and four-probe dc technique. The contributions of bulk and grain boundary resistances were determined, effective conductivity activation energies were calculated.     

Electrochemical studies of LiCr x Fe x Mn2?2x O4 in an aqueous electrolyte

In this paper, LiCr _x Fe _x Mn_2−2x O₄ (x = 0, 0.05, 0.1) electrode materials were prepared by sol–gel technique and characterized by X-ray diffraction (XRD) and transmission electron microscopy or high-resolution transmission electron microscopy techniques. XRD results reveal that the Cr–Fe-co-doped LiCr _x Fe _x Mn_2−2x O₄ materials are phase-pure spinels. The electrochemical properties of the LiMn₂O₄, LiCr_0.05Fe_0.05Mn_1.9O₄, and LiCr_0.1Fe_0.1Mn_1.8O₄ electrodes in 5 M LiNO₃ aqueous electrolyte were investigated using cyclic voltammetry, AC impedance, and galvanostatic charge/discharge methods. In the current range of 0.5–2 A g⁻¹, the specific capacity of the LiCr_0.05Fe_0.05Mn_1.9O₄ electrode is close to that of the LiMn₂O₄ electrode, but the specific capacity of the LiCr_0.1Fe_0.1Mn_1.8O₄ electrode is obviously lower than that of the LiMn₂O₄ electrode. When the electrodes are charge/discharge-cycled at the high current rate of 2 A g⁻¹, the LiCr_0.05Fe_0.05Mn_1.9O₄ electrode exhibits an initial specific capacity close to that of the LiMn₂O₄ electrode, but its cycling stability is obviously prior to that of the LiMn₂O₄ electrode.     

Synthesis and magnetic properties of Cu0.5Fe0.5 ? x In x Cr2S4 (x = 0?0.4) solid solutions

Multistep synthesis with X-ray diffraction monitoring of the phase composition has been carried out, optimal synthesis parameters have been determined, and the magnetic properties of solid solutions between thiospinels with ordered tetrahedral A lattices (ferrimagnet Cu_0.5Fe_0.5Cr₂S₄ (T _C = 347 K) and anti-ferromagnet Cu_0.5In_0.5Cr₂S₄ (T _N = 35 K) have been studied. Both compounds crystallize in F $\bar 4$ 3m (T _d ² ) structure. Measurements over wide ranges of fields (0.05?C40 kOe) and temperatures (5?C300 K) highlighted the nature of magnetism in the samples; new magnetic species have been discovered.     

Synthesis and characterization of nano-structured Th1?x Ce x O2 mixed oxide

GEL combustion technique was applied to obtain oxides of thorium and cerium from their respective nitrate solutions using citric acid as the gelating agent. The dried samples were characterized by IR and TG studies. Intermediate and final products during TG studies have been isolated and characterized by XRD studies. All the TG runs during heating of thorium and cerium nitrate with citric acid dried Gels showed a two step process. The weight loss at each step and the X-ray data of the product at each step, helped in suggesting a possible mechanism. Kinetic study was carried out independently for each step. The reaction mechanism as observed during interactive procedure was found to be diffusion controlled. The kinetic parameters (activation energy and pre-exponential factor) for each step in all reactions have been calculated. Observations from XRD studies show that with increase in cerium concentration in the oxides, the lattice parameter values have shown a decreasing trend for all the five compositions studied. It was observed that in TG studies with increase in cerium concentration, the final temperature of the reactions have shown a decreasing trend. SEM studies of the powders reveal that synthesized oxides have a tendency to form agglomerate of varying size ranging from 50 to 100 μm in case of mixed oxides but the size of thorium oxide powder so synthesized have pore size 10–100 μm. SEM images shows that GEL combustion may result in agglomeration, if the temperature is not properly controlled to the desired value. SEM studies also reveal that each agglomerate contains approximately 10–100 individual particles. Surface area of the mixed oxide powders were determined using Gas adsorption technique. The surface area was found to be in the range of 3–17 m²/g in all cases. Specific surface area of thorium oxide was found to be lesser than cerium oxide but in case of mixed oxides surface area decreases with increase in cerium content. Majority of pores, indicating the particle size are in the range of 0.01–0.04 cm³/g.     

Nature of conductivity of Perovskites La1 ? x Sr x ScO3 ? α (x = 0.01–0.15) under oxidative and reducing conditions

Transport numbers of ions and protons are measured on ceramic samples of La_{1 ? x} Sr _x ScO_{3 ? ??} (x = 0.01?C0.15); partial conductivities (hole, proton, and oxygen-ion) are determined in the temperature range of 500?C900°C at pH₂O = 0.04?C2.35 kPa and pO₂ from air to 10^?15 Pa.     

Study of ceramic pigments based on Er2Ce2?x Mo x O7

This contribution is focused on the synthesis, characterization and optical properties of new inorganic pigments which are environment friendly and can substitute some toxic metals in interesting colour compounds. Pyrochlores belong to the group of high-temperature pigments, and are a variety of actual and potential applications for several materials. Examples include catalysts, thermal barrier coatings, solid electrolytes, nuclear waste forms and host materials for luminescence centers. The pigments were prepared by the solid state reaction and also by method of suspension mixing of materials in the series with increasing content of molybdenum. The pigments were applied into organic matrix and ceramic glaze. The colour properties of these applications were investigated depending on content of Mo, method of preparation and temperature of calcination (1350?C1550?°C after step 50?°C). The optimum conditions for their synthesis were determined. The pigments were evaluated from standpoint of their structure, colour and particle sizes. Characterization of Er₂Ce_2?x Mo _x O₇ pigments (x?=?0.1, 0.3, 0.5 and 0.7) suggests that they have a potential to be alternative yellow or orange colourants for paints, plastics, ceramics and building materials.     

Structures and optical properties of Zn1?x Ni x O nanoparticles by coprecipitation method

Nanocrystals of undoped and nickel-doped zinc oxide (Zn_1?x Ni _x O, where x?=?0.00?C0.05) were synthesized by the coprecipitation method. Crystalline size, morphology, and optical absorption of prepared samples were determined by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), and UV?Cvisible spectrometer. XRD and SEM studies revealed that Ni-doped ZnO crystallized in hexagonal wurtzite structure. Doping of ZnO with Ni²⁺ was intended to enhance the surface defects of ZnO. The incorporation of Ni²⁺ in place of Zn²⁺ provoked an increase in the size of nanocrystals as compared to undoped ZnO. Crystalline size of nanocrystals varied from 10 to 40?nm as the calcination temperature increased. Enhancement in the optical absorption of Ni-doped ZnO indicated that it can be used as an efficient photocatalyst under visible light irradiation. Optical absorption measurements indicated a red shift in the absorption band edge upon Ni doping. The band gap value of prepared undoped and Ni-doped ZnO nanoparticles decreased as annealing temperature was increased up to 800?°C.     

Study of Nd2–x Ce x CuO4?±?δ (x?=?0.1–0.25) as cathode material for intermediate-temperature solid oxide fuel cells

The solid solubility limit of Ce in Nd_2–x Ce _x CuO_4 ± δ , prepared by sol–gel process, is established up to x = 0.2. The transition from negative temperature coefficient to positive temperature coefficient, within the solid solubility region, is observed at 620 °C. The area-specific-resistance (ASR) is optimized for electrochemical cell sintered at 800 °C. ASR enhances with increase in sintering temperature of cell. ASR value of 0.93 ohm cm² at 700 °C, determined by electrochemical impedance spectroscopy is comparable against that by voltage versus current (V–I) characteristics at 0.98 ohm cm² at the same temperature. Electrochemical performance and ASR of Nd_1.8Ce_0.2CuO_4 ± δ is improved when prepared by sol–gel route over solid-state reaction, which is attributed to uniform size and shape of nanocrystalline grains.     

Magnetic properties of Cu0.5Fe0.5 ? x Ga x Cr2S4 solid solutions

Solid solutions between ferrimagnet Cu_0.5Fe_0.5Cr₂S₄ (T _C = 347 K) and antiferromagnet Cu_0.5Ga_0.5Cr₂S₄ (T _N = 31 K) have been synthesized, and their magnetic properties studied. Both compounds belong to the A _0.5 ⁺ A _0.5 ³⁺ Cr₂X₄ group with the 1 : 1 order of A⁺ and A³⁺ ions in the tetrahedral spinel sites. Measurements on a SQUID magnetometer over wide ranges of fields (0.05?C40 kOe) and temperatures (5?C300 K) provided a deeper insight into the nature of magnetism and cation distribution in the studied samples.     

Synthesis and magnetic properties of CuCr1.5Sb0.5S4 ? x Se x solid solutions

CuCr_1.5Sb_0.5S_{4 ? x} Se _x (x = 0, 0.5, 3.5, 4) metal chalcogenides with spinel structure have been synthesized for the first time. Unit cell parameters have been calculated and magnetic properties have been measured for the samples prepared. These samples are nonuniform antiferromagnets having Neel temperatures of T _N = 21?C30 K.     

Electrical, electrochemical, and thermomechanical properties of perovskite-type (La1?x Sr x )1?y Mn0.5Ti0.5O3?δ (x?=?0.15–0.75, y?=?0–0.05)

Strontium additions in (La_1?x Sr _x )_1?y Mn_0.5Ti_0.5O_3?δ (x?=?0.15–0.75, y?=?0–0.05) having a rhombohedrally distorted perovskite structure under oxidizing conditions lead to the unit cell volume contraction, whilst the total conductivity, thermal and chemical expansion, and steady-state oxygen permeation limited by surface exchange increase with increasing x. The oxygen partial pressure dependencies of the conductivity and Seebeck coefficient studied at 973–1223?K in the p(O₂) range from 10^?19 to 0.5?atm suggest a dominant role of electron hole hopping and relatively stable Mn³⁺ and Ti⁴⁺ states. Due to low oxygen nonstoichiometry essentially constant in oxidizing and moderately reducing environments and to strong coulombic interaction between Ti⁴⁺ cations and oxygen anions, the tracer diffusion coefficients measured by the ¹⁸O/¹⁶O isotopic exchange depth profile method with time-of-flight secondary-ion mass spectrometric analysis are lower compared to lanthanum–strontium manganites. The average thermal expansion coefficients determined by controlled-atmosphere dilatometry vary in the range 9.8–15.0?×?10^?6?K^?1 at 300–1370?K and oxygen pressures from 10^?21 to 0.21?atm. The anodic overpotentials of porous La_0.5Sr_0.5Mn_0.5Ti_0.5O_3?δ electrodes with Ce_0.8Gd_0.2O_2-δ interlayers, applied onto LaGaO₃-based solid electrolyte, are lower compared to (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3?δ when no metallic current-collecting layers are introduced. However, the polarization resistance is still high, ~2 Ω?×?cm² in humidified 10?% H₂–90?% N₂ atmosphere at 1073?K, in correlation with relatively low electronic conduction and isotopic exchange rates. The presence of H₂S traces in H₂-containing gas mixtures did not result in detectable decomposition of the perovskite phases.     

Improved electrochemical properties of chromium substituted in LiCr1 ? x Ni x O2 cathode materials for rechargeable lithium-ion batteries

Pristine- and chromium-substituted LiNiO₂ nanoparticles were synthesized by sol-gel method using nitrate precursor at 800?°C for 12?h. Physical properties of the synthesized product were analyzed using Fourier transform infrared, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive analysis X-ray. XRD studies revealed a well-defined layer structure and a linear variation of lattice parameters with the addition of chromium and no impurities. Surface morphology and particle size of synthesized materials were changed with chromium addition using SEM and TEM analyses. Assembled lithium-ion cells were evaluated for charge/discharge studies at different rates, cyclic voltammetry, and electrochemical impedance spectra. The initial discharge capacity of LiNiO₂ cathode material was found to be 168?mA hg^?1; however, discharge capacity increased in chromium substitution. Electrochemical impedance spectroscopy revealed that LiCr_0.10Ni_0.90O₂ could enhance charge transfer resistance upon cycling. The substitution of Ni with chromium, LiCr_0.10Ni_0.90O₂, had better cycle life, low irreversible capacity, and excellent electrochemical performance.     

On some multiplicative product of kth derivative of Dirac's delta in x0+|x| and x0−|x|

In this paper we give a sense to the products $${{\left| x \right|^{(n - 2)/2} }} \cdot \frac{{\delta ^{(k - 1)} (x_0 + \left| x \right|)}} {{\left| x \right|^{(n - 2)/2} }}$$ and $\delta ^{(k - 1)} (x_0 - \left| x \right|) \cdot \delta ^{(k - 1)} (x_0 + \left| x \right|)$ . The first of them is a generalization of the product $${{\left| x \right|^{(n - 2)/2} }} \cdot \frac{{\delta (x_0 + \left| x \right|)}} {{\left| x \right|^{(n - 2)/2} }}{\text{ }}$$ given in [1, p. 158].     

Hydrogen content in proton-conducting perovskites CaZr1 − x Sc x O3 − x /2 (x = 0.0–0.2)

The hydrogen content in CaZr_{1 ? x} Sc _x O_{3 ? x/2} (x = 0.00–0.20) and BaZr_0.9Y_0.1O_3-α (for comparison) was studied by powder nuclear microanalysis. The samples were saturated with heavy water (D₂O) vapors at 350 and 400°C in air. The chemical expansion of the CaZr_0.95Sc_0.05O_3-α and BaZr_0.95Y_0.05O_3-α samples at 700°C was measured at different water vapor pressures. A model was suggested to explain the lowered hydrogen content in oxides based on CaZrO₃.     

Kinetics of phase transition and thermal stability in Se80?x Te20Zn x (x?=?2, 4, 6, 8, and 10) glasses

Se_80?x Te₂₀Zn _x (x?=?2, 4, 6, 8, and 10) glasses have been prepared using conventional melt quenching technique. The kinetics of phase transformations (glass transition and crystallization) have been studied using differential scanning calorimetry (DSC) under non-isothermal condition at five different heating rates in these glasses. The activation energy of glass transition (E _t), activation energy of crystallization (E _c), Avrami exponent (n), dimensionality of growth (m), and frequency factor (K _o) have been investigated for the better understanding of growth mechanism using different theoretical models. The activation energy is found to be highly dependent on Zn concentration. The rate of crystallization is found to be lowest for Se₇₀Te₂₀Zn₁₀ glassy alloy. The thermal stability of these glasses has been investigated using various stability parameters. The values of these parameters were obtained using characteristic temperatures, such as glass transition temperature T _g, onset crystallization temperature T _c, and peak crystallization temperature T _p. In addition to this, enthalpy-released during crystallization has also been determined. The values of stability parameters show that the thermal stability increases with the increase in Zn concentration in the investigated glassy samples.     

Atoms state and interatomic interactions in perovskite-like oxides: XXXII. Formation of paramagnetic clusters in the La1−0.33x Ca0.33x Fe x Al1−x O3 and La1−0.33x Sr0.33x Fe x Al1−x O3 solid solutions

Calcium- and strontium-containing lanthanum orthoferrites have been studied using magnetic dilution method. It has been shown that the iron-atom clusters with competing ferro- and antiferromagnetic exchange interactions can exist. By using Mossbauer spectroscopy, Fe(IV) atoms have been found in the La_1?0.33x Ca_0.33x Fe_xAl_1?x O₃ solid solutions and Fe(III) atoms in two different surroundings have been found in the La_1?0.33x Sr_0.33x Fe _x Al_1?x O₃ solid solutions. The compositions of paramagnetic clusters stable at the infinite dilution have been proposed basing of the magnetic susceptibility and Mossbauer spectroscopy data.     

Electrochemical testing of composite electrodes of (La1?x Sr x ) s MnO3 and doped ceria in NO-containing atmosphere

The possibility of using electrochemical cells for removal of NO _x from an exhaust gas with excess O₂ has been examined. (La_1−x Sr _x ) _s MnO₃ (LSM) and ceria doped with Pr or Gd were selected as electrode materials and investigated in three-electrode cells. The electrodes were characterised electrochemically with electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), and the gas composition monitored while the electrodes were polarised. The electrodes of (La_0.5Sr_0.5)_0.99MnO₃ (LSM50) and Ce_0.8Pr_0.2O_2−δ exhibit higher current densities in 0.1% NO in Ar than in air at 300 to 400 °C during CV. This indicates some apparent selectivity towards NO compared to O₂. The electrodes can remove NO, when polarised to at least −0.6 V vs. Pt/Air at 600 °C, and EIS measurements under polarisation indicate that the kinetics of the electrodes change, when the electrode potential gets below −0.6 V vs. Pt/Air.     

Radiation damage in Si1−x Ge x heteroepitaxial devices

Results are presented of an extended study on the induced lattice defects and their effects on the degradation of Si_1−x Ge _x devices, subjected to a 20 MeV alpha-ray, 1 MeV electron, 1 MeV fast neutron, and 20 and 86 MeV proton irradiations. The degradation of the electrical device performance increase with increasing fluence, while it decreases with increasing germanium content. In the Si_1−x Ge _x epitaxial layers, electron capture levels associated with an interstitial-substitutional boron complex are induced. The radiation source dependence of performance degradation is attributed to the difference of mass and the probability of nuclear collision for the formation of lattice defects.     

Solid potassium-conducting electrolytes in the K2 − 2x Ga2 − x V x O4 system

New potassium-conducting solid electrolytes based on potassium monogallate in the K_2?2x Ga_2?x V _x O₄ system are synthesized and studied. It is found that an introduction of V⁵⁺ ions leads to a considerable increase in the KGaO₂ conductivity due to the formation of vacancies in the potassium sublattice. The conductivity for optimal compositions is approximately 10^?3 S cm^?1 at 400°C and above 10^?2 S cm^?1 at 700°C. The results are compared with early obtained data for potassium monogallate dopped with four-charged cations.     

Synthesis and crystal structure of Mo6−x Nb x I11 (x = 1–1.5)

A solid solution Mo_{6 ? x} Nb _x I₁₁ (x = 1.1–1.5) containing cluster cores {Mo₅NbI₈} is obtained by the high-temperature reaction of molybdenum, niobium, and iodine (550°C, 70 h, quartz ampule). According to the X-ray diffraction data, heating at 800°C in a molybdenum container results in the decomposition of the solution to Mo₆I₁₂ and Nb₆I₁₁. According to the X-ray structure analysis data, the compounds are isostructural to the high-spin modification Nb₆I₁₁ (space group Pccn). The presence of Nb atoms in the structure changes the structural type from the layered (Mo₆I₁₂) to framework structure, noticeably increases the metalmetal distances (2.661–2.716 Å, 2.695 Å) Mo₆ octahedron with the retention of the distance from the metal (M) to the μ₃-“capped” I atoms, and strongly elongates the M₆-I-M₆ bridges almost to the value observed in Nb₆I₁₁.