反相液相色谱-质谱法使用甲酸甲胺改善甘油三酯电喷雾离子化检测灵敏度

提出使用甲酸甲胺作为新型电离增强剂改善反相液相色谱-电喷雾质谱(LC-ESI-MS)检测甘油三酯灵敏度的方法.使用反相C18色谱柱,以玉米油的异丙醇溶液为样品,选择文献中常用的异丙醇-乙腈-甲醇-水,异丙醇-乙腈流动相,在考察甲酸、乙酸、甲酸铵、乙酸铵、甲酸丁胺、甲酸二丁胺、甲酸三乙胺、甲酸二乙胺、甲酸甲胺、甲酸乙胺等不同电离增强剂的基础上,比较了甲酸甲胺和常用的甲酸铵电离增强剂对LC-ESI-MS分析甘油三酯检测灵敏度的影响,结果表明,甲酸甲胺可以使其中三亚油酸甘油酯组分的质谱峰响应值和信噪比均约为使用甲酸铵的5倍.考察了使用甲酸甲胺时,甲酸甲胺电离增强剂的浓度、流动相流速以及雾化气流速对检测的影响.通过测定不同玉米油浓度与其中甘油三酯总离子流色谱峰面积的关系曲线,显示玉米油中甘油三酯组分在不同流动相的电喷雾过程中出现聚集的最小浓度相差不大,三亚油酸甘油酯峰面积与浓度在7×10-7~2×10-4 mol/L范围内的线性关系较好,相关系数R2=0.9997,在更高的浓度时则峰面积增加缓慢.根据实验数据分析甲酸甲胺改进检测的机理,提出含有疏水性基团的加合甲胺单电荷离子具有较低的溶剂化能,在雾滴表面富集的加合甲胺离子容易被蒸发,从而提高了电喷雾离子化效率.本方法为LC-ESI-MS分析食用油中甘油三酯时提高检测灵敏度提供了有效途径.     

辅助电极对纳升电喷雾影响的研究

电喷雾质谱作为一种有效的软电离技术易于和各种液相分离技术如高效液相色谱以及毛细管电泳等技术实现在线联用,已越来越广泛地用于生物大分子的分析鉴定,但常规电喷雾技术要求分析试剂流速一般为1～10μL／min,耗样量大．因而低样品消耗、高灵敏的纳升电喷雾技术的研究越来越受到重视。纳升电喷雾技术因其喷雾头口径较小,产生的泰勒锥体也相应减小,样品分子的去溶剂化和离子化效率大大提高,有文献报道,利用纳升电喷雾技术可检测到10^-18mol级蛋白样品。     

电喷雾解吸电离质谱法用于临床尿样的直接分析

将电喷雾解吸电离质谱(DESI-MS)用于临床尿样的分析, 优化了电喷雾溶剂流速、电喷雾电压和喷雾锥距离等重要参数. 采用普通滤纸作为样品载体, 在不需要样品预处理的前提下同时快速测定了临床尿样中的钾、钠、尿素、尿酸、丙酮酸和肌苷等多种成分, 并对各种成分的主要离子进行了串联质谱鉴定. DESI-MS在进行多组分同时测定时不需要进行样品预处理, 缩短了测定时间, 单个样品的分析时间不到1 min. 同时, 采用内标法对所测定组分进行了半定量分析.     

电喷雾离子迁移谱检测氨基酸及多肽的研究

建立了氨基酸及多肽的电喷雾离子迁移谱检测方法.采用自制的电喷雾离子迁移谱装置,在室温条件下以甲醇为溶剂,空气为漂移气体,流速为1000 mL/min,电喷液流速为2 mL/min,测试了甘氨酸、胱氨酸、组氨酸、精氨酸4种氨基酸及缓激肽片段(1~7)和P物质2种多肽的离子迁移谱,计算出上述化合物的约化迁移率.离子迁移谱图反映出化合物的结构信息,具有指纹谱特征.此装置在1 min的检测时间内对P物质的检测灵敏度达到855 ng/mL.结果表明,电喷雾离子迁移谱可用于氨基酸及多肽类化合物的现场快速鉴定.     

电喷雾质谱法对几种氨基酸的快速检测

利用电喷雾质谱技术对甘氨酸、N-(羧甲基)甘氨酸、谷氨酸混合样品进行了检测,考察了电离源的喷雾电压、喷雾气压、进样流速对检测结果的影响规律。结果表明,以1:1(V/V)的甲醇水溶液作为溶剂时,甘氨酸、N-(羧甲基)甘氨酸、谷氨酸能够有效地被电离,产物离子均为母体离子结合一个质子(M~+H)~+。当电喷雾电压从1 kV增加到6 kV过程中,离子信号强度迅速增加,增大到5 kV后基本保持不变。注入流速在1~5μL/min间信号强度随注入流速增加而迅速增大,之后基本保持不变。喷雾气压低于4 MPa时,信号不稳定;在4~12 MPa气压范围内信号稳定且对信号强度影响不大。     

黄连生物碱的反相高效液相-电喷雾离子阱串联质谱的研究

采用反相高效液相-电喷雾离子阱串联质谱法对由乙醇提取的黄连生物碱进行了研究.优化出了反相高效液相色谱分离黄连生物碱的条件:流动相为V(乙腈):V(H2O)(三乙胺2 mmol/L)=30:70;柱温为30℃;流速为0.5 mL/min,并结合电喷雾串联质谱检测出了黄连生物碱中的小檗碱、药根碱、巴马汀、黄连碱以及微量的表...     

溶剂浮选法分离富集污水中痕量羧酸类和胺类有机污染物的研究

本文报道了溶剂浮选法分离富集污水中痕量羧酸类有机污染物和胺类有机污染物的新方法。考察了溶液的pH值、通气速度、离子强度、浮选时间、相比以及不同溶剂对浮选效果的影响。在优化了浮选条件下溶剂浮选效率达到95％以上。采用本法对石化工业污水中的痕量羧酸类和胺类物质进行分离富集和鉴定,证明了该法的可行性。     

臭氧与二乙胺和三乙胺气相反应的速率常数

利用自制的烟雾箱系统研究了臭氧与二乙胺和三乙胺的气相反应动力学. 实验过程中保证二乙胺和三乙胺浓度远远大于臭氧浓度, 使得实验在准一级条件下进行. 加入环己烷以消除实验过程中可能产生的OH自由基对反应的影响. 在(298±1) K和1.01×105 Pa条件下, 测得臭氧与二乙胺和三乙胺反应的绝对速率常数值分别为(1.33±0.15)×10^-17和(8.20±1.01)×10^-17 cm³·molecule^-1·s^-1. 与文献中已有的其它胺类的臭氧反应数据比较后发现, 臭氧与胺的反应可以用亲电反应机制来解释. 另外, 通过对比发现, 臭氧与三取代的烷基胺类的反应速率要远远大于其与二取代的烷基胺类的反应速率. 这在一定程度上可有助于解释外场观测到的气溶胶相中二烷基胺盐较多的事实. 利用测得的速率常数和大气中臭氧浓度, 还估算了二乙胺和三乙胺与臭氧反应的大气寿命. 结果显示, 与臭氧的反应是二乙胺和三乙胺在大气中的一种重要的消除途径, 尤其是在污染严重地区.     

臭氧与二乙胺和三乙胺气相反应的速率常数

利用自制的烟雾箱系统研究了臭氧与二乙胺和三乙胺的气相反应动力学. 实验过程中保证二乙胺和三乙胺浓度远远大于臭氧浓度, 使得实验在准一级条件下进行. 加入环己烷以消除实验过程中可能产生的OH自由基对反应的影响. 在(298±1) K和1.01×105 Pa条件下, 测得臭氧与二乙胺和三乙胺反应的绝对速率常数值分别为(1.33±0.15)×10^-17和(8.20±1.01)×10^-17 cm³·molecule^-1·s^-1. 与文献中已有的其它胺类的臭氧反应数据比较后发现, 臭氧与胺的反应可以用亲电反应机制来解释. 另外, 通过对比发现, 臭氧与三取代的烷基胺类的反应速率要远远大于其与二取代的烷基胺类的反应速率. 这在一定程度上可有助于解释外场观测到的气溶胶相中二烷基胺盐较多的事实. 利用测得的速率常数和大气中臭氧浓度, 还估算了二乙胺和三乙胺与臭氧反应的大气寿命. 结果显示, 与臭氧的反应是二乙胺和三乙胺在大气中的一种重要的消除途径, 尤其是在污染严重地区.     

臭氧与二乙胺和三乙胺气相反应的速率常数

利用自制的烟雾箱系统研究了臭氧与二乙胺和三乙胺的气相反应动力学. 实验过程中保证二乙胺和三乙胺浓度远远大于臭氧浓度, 使得实验在准一级条件下进行. 加入环己烷以消除实验过程中可能产生的OH自由基对反应的影响. 在(298±1) K和1.01×105 Pa条件下, 测得臭氧与二乙胺和三乙胺反应的绝对速率常数值分别为(1.33±0.15)×10^-17和(8.20±1.01)×10^-17 cm³·molecule^-1·s^-1. 与文献中已有的其它胺类的臭氧反应数据比较后发现, 臭氧与胺的反应可以用亲电反应机制来解释. 另外, 通过对比发现, 臭氧与三取代的烷基胺类的反应速率要远远大于其与二取代的烷基胺类的反应速率. 这在一定程度上可有助于解释外场观测到的气溶胶相中二烷基胺盐较多的事实. 利用测得的速率常数和大气中臭氧浓度, 还估算了二乙胺和三乙胺与臭氧反应的大气寿命. 结果显示, 与臭氧的反应是二乙胺和三乙胺在大气中的一种重要的消除途径, 尤其是在污染严重地区.     

Development and evaluation of a nano-electrospray ionisation source for atmospheric pressure ion mobility spectrometry

A nano-electrospray ionisation source has been designed and constructed for a high temperature ion mobility spectrometer. The drift cell was modified by replacement of the 63Ni atmospheric pressure chemical ionisation source with a tube lens/desolvation region and operated using commercial nano-electrospray capillaries. Ions were introduced into the drift region via a Bradbury-Nielson gate (pulse width 50 micros, repetition period 20 ms). A unidirectional flow of nitrogen was used as the drift gas at temperatures in the range 100-150 degrees C to aid desolvation. The performance of the nano-electrospray ion source has been demonstrated for analytes including crown ethers, amino acids and peptides. Reduced mobilities determined by nano-ESI were consistent with those reported using a 63Ni ion source.     

Improved design for high resolution electrospray ionization ion mobility spectrometry

An improved design for high resolution electrospray ionization ion mobility spectrometry (ESI-IMS) was developed by making some salient modifications to the IMS cell and its performance was investigated. To enhance desolvation of electrospray droplets at high sample flow rates in this new design, volume of the desolvation region was decreased by reducing its diameter and the entrance position of the desolvation gas was shifted to the end of the desolvation region (near the ion gate). In addition, the ESI source (both needle and counter electrode) was positioned outside of the heating oven of the IMS. This modification made it possible to use the instrument at higher temperatures, and preventing needle clogging in the electrospray process. The ion mobility spectra of different chemical compounds were obtained. The resolving power and resolution of the instrument were increased by about 15-30% relative to previous design. In this work, the baseline separation of the two adjacent ion peaks of morphine and those of codeine was achieved for the first time with resolutions of 1.5 and 1.3, respectively. These four ion peaks were well separated from each other using carbon dioxide (CO₂) rather than nitrogen as the drift gas. Finally, the analytical parameters obtained for ethion, metalaxyl, and tributylamine indicated the high performance of the instrument for quantitative analysis.     

阴离子交换整体柱对蛋白质的分离与纯化

分别用乙二胺、二乙胺、三乙胺将自制的以甲基丙烯酸缩水甘油酯(GMA)为单体、乙二醇二甲基丙烯酸酯(EDMA)为交联剂的整体柱修饰为弱、强阴离子交换整体柱。考察了该整体柱的性能,选择出分离蛋白质(牛血清白蛋白、溶菌酶和谷胱甘肽)的最佳实验条件,并在最佳分离条件下考察了这些蛋白质在整体柱上的色谱行为和该整体柱对纤维素降解酶的分离纯化情况。实验结果表明,该整体柱性能良好,可以实现对纤维素降解酶的快速分离与纯化。同时,实验也证明采用梯度洗脱可以实现对某些蛋白质的分离纯化。     

Etude de la reactivite du tris(tertiobutyl)phenyldithiophosphorane

Heating of tris(tertiobutyl)phenyldithiophosphorane gives rise to an isomer with a tetracoordinated phosphorus atom. The action of triphenylphosphine loads to a tricyclophosphathiane which can be transformed in diphosphene by an excess of triphenylphosphine. Reactions with various nucleophilic derivatives (pyridine, triethylamine, diethylamine, butylamine, water, tetraphenylarsonium chloride) are described.     

Facile synthesis of poly(l‐tryptophan) through polycondensation of activated urethane derivatives

A facile and phosgene‐free synthetic route to poly(l ‐tryptophan) 2 by the polycondensation of N‐phenoxycarbonyl‐l ‐tryptophan 1 is described. The monomer 1 was synthesized via the carbamylation of tetrabutylammonium salt of L‐tryptophan with diphenyl carbonate. The polycondensation proceeded smoothly at 60 °C in N,N‐dimethylacetamide in the presence of amines (n‐butylamine, diethylamine, and triethylamine) along with the elimination of phenol and carbon dioxide. The structural analysis of the obtained 2 by Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry revealed that n‐butylamine or diethylamine was successfully incorporated into the chain end of the polypeptide. Furthermore, we have demonstrated the synthesis of a diblock copolymer by utilizing amine‐terminated poly(ethylene glycol) as a source of the polyether segment. The chain length of the polypeptide segment was controlled by varying feed ratio between 1 and the amino group of poly(ethylene glycol). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4565–4571     

Highly sensitive gas-diffusion sequential injection analysis based on flow manipulation

The present paper describes approaches utilizing the powerful flow manipulation capabilities of sequential injection analysis (SIA) to substantially improve the efficiency of gas-diffusion separation compared to its traditional implementation in flow injection analysis (FIA). Ammonia, ethylamine, diethylamine and triethylamine were used as model analytes in this study. Eleven flow manipulation approaches involving continuous flow, stop-flow, oscillating flow, and the introduction of air bubbles to separate the sample zone from the donor solution were tested. Improvement in sensitivity compared to traditional gas-diffusion FIA exceeding one order of magnitude was achieved. It was observed that this improvement increased with the molecular size of the analyte.     

Complexation of Magnesium Acetylacetonate with Tetraazaporphine in Nitrogen-Containing Base–Benzene System

Kinetics of complexation between magnesium acetylacetonate and tetraazaporphine in benzene–pyridine (2-methylpyridine) system is studied. The rate and activation parameters of the process were found to be determined by the addition of these bases. A possible mechanism of the Mg complex formation is discussed. No magnesium complex with tetraazaporphine was formed in benzene–morpholine (benzylamine, n-butyl-amine, diethylamine, triethylamine, tributylamine) system.     

Catalytic Condensation of Primary Amines, Dehydrogenation of Secondary Amines, and Dealkylation of Tertiary Amines over Solid-State Rhenium Sulfide Clusters with an Octahedral Metal Framework

When solid-state rhenium sulfide clusters with an octahedral metal framework are treated in a hydrogen stream above 300 °C, a catalytic activity for condensation of butylamine to yield N-butylidenebutylamine develops. Primary amines such as ethylamine, pentylamine, and hexylamine are also converted to the corresponding N-alkylidenealkylamines. Secondary amines such as diethylamine, dipropylamine, and dibutylamine are dehydrogenated to the corresponding N-alkylidenealkylamines. When triethylamine is allowed to react, dealkylation proceeds to yield diethylamine and its dehydrogenated product N-ethylideneethylamine. Trimethylamine is also dealkylated to dimethylamine. This series of catalytic behavior is the same as that of palladium and platinum metals. The similarity in selectivity is attributable to the rhenium atom that accepts electrons from the sulfur ligands leading to isoelectronic with the platinum group metals.     

Thermal decomposition of immobilized compounds for the generation of gaseous standard mixtures containing ammonia and amines

The thermal decomposition of phthalamic acid derivatives chemically bonded to the surface of silica gel was examined and utilized for the generation of single-component gaseous standard mixtures of ammonia, methylamine, diethylamine and triethylamine. The conditions of the thermal decomposition (temperature, time, diluent gas flow rate) were optimized to ensure complete liberation and rapid elution of the compounds from the bed of modified silica gel. The total amounts of these four compounds that can be released from unit mass of the modified silica gel are in the range of several mg.     

电热蒸发进样微波诱导等离子体原子吸收光谱法测定银和镉的研究

研究了以常压低功率氩微波诱导等离子体（ＭＩＰ）为原子化器的原子吸收光谱法（ＡＡＳ）测定银和镉。采用电热蒸发（ＥＴＶ）,浓Ｈ２ＳＯ４吸收去溶的进样方法。考察了微波前向功率,载气流量,去溶电压,去溶时间,蒸发电压,酸度对银,镉测定的影响。方法已用于试样分析。