A computational investigation of unsteady turbulent wake–boundary-layer interaction

The relative motion of rotor and stator blade rows in a turbomachine generates periodically unsteady flow on the blades due to travelling wake perturbations. To better understand the attendant wake–boundary-layer interaction a calculation procedure was developed to model the behaviour of this complex unsteady flow. Due to nonlinear interactions with the boundary layer, the travelling discrete frequency wakes were found to decrease the velocity profile shape factor. For the range of reduced frequencies examined (=0.33–9.33) the skin-friction coefficient was found to be frequency dependent. The calculated results for both steady and unsteady velocity profiles, and for skin friction compared well with experimental data. Although the agreement between measured and calculated velocity phase shift was poor, in both experimental and model results the negative phase shift throughout the boundary layer due to the travelling-wave fluctuations has been captured.     

Shallow wakes generated on smooth and rough surfaces

This study deals with the behavior of shallow turbulent wakes generated on smooth and rough surfaces. The wake generator used is a flat plate placed normal to the flow. Experiments were conducted at flow depths of 40 and 80 mm. The boundary layer thickness in the approaching flow occupies 60–75% of the flow depth. The Reynolds number based on the plate width and approaching freestream velocity varies from 13.0 × 10³ to 14.5 × 10³. Velocity measurements were carried out in the near-wake region (1–10 plate widths) using a laser-Doppler anemometer. The mean velocity distributions at various axial stations collapse onto a single curve by a proper choice of the length and velocity scales. It is important to note that a sense of self-similarity is attained even in the near-wake region. Attempts were made to clarify the relative effects of the transverse shear and bed friction in shallow open channel wakes. Received: 11 February 1999/Accepted: 30 August 2000     

Flow field analysis of a turbulent boundary layer over a riblet surface

The near-wall flow structures of a turbulent boundary layer over a riblet surface with semi-circular grooves were investigated experimentally for the cases of drag decreasing (s ⁺=25.2) and drag increasing (s ⁺=40.6). One thousand instantaneous velocity fields over riblets were measured using the velocity field measurement technique and compared with those above a smooth flat plate. The field of view was 6.75 × 6.75 mm² in physical dimension, containing two grooves. Those instantaneous velocity fields were ensemble averaged to get turbulent statistics including turbulent intensities and turbulent kinetic energy. To see the global flow structure qualitatively, flow visualization was also carried out using the synchronized smoke-wire technique under the same experimental conditions. For the case of drag decreasing (s ⁺=25.2), most of the streamwise vortices stay above the riblets, interacting with the riblet tips frequently. The riblet tips impede the spanwise movement of the streamwise vortices and induce secondary vortices. The normalized rms velocity fluctuations and turbulent kinetic energy are small near the riblet surface, compared with those over a smooth flat plate. Inside the riblet valleys, these are sufficiently small that the increased wetted surface area of the riblets can be compensated. In addition, in the outer region (y ⁺ > 30), these values are almost equal to or slightly smaller than those for the smooth plate. For the case of drag increasing (s ⁺=40.6), however, most of the streamwise vortices stay inside the riblet valleys and contact directly with the riblet surface. The high-speed down-wash flow penetrating into the riblet valley interacts actively with the wetted riblet surface and increases the skin friction. The rms velocity fluctuations and turbulent kinetic energy have larger values compared with those over a smooth flat plate. Received: 24 March 1999/Accepted: 10 March 2000     

Velocity measurements of wake-induced unsteady flow in a linear turbine cascade

Extensive velocity measurements have been taken in a linear turbine cascade with unsteady oncoming wakes. The unsteady wakes were generated by moving cylinders on a squirrel cage device. The Reynolds number was 1.1 × 10⁵, and the Strouhal number varied from o to 7.36. The blade-to-blade flow and the boundary layers on the suction side were measured with a hot-wire anemometer. The results were obtained in ensemble-averaged form so that periodic unsteady processes can be studied. Of particular interest was the transition of the boundary layer. The boundary layer remained laminar in the case without wakes. The passing wakes caused transition, and the beginning of transition moves forward as the wake-passing frequency increases. Unlike in the flat plate study of Liu and Rodi (1991a) the boundary layer state hardly changed with time, although the turbulence level in the boundary layer showed clear periodic response to the passing wakes. The work reported here was sponsored by the German Federal Ministry of Research and Technology through program TURBOTHERM under contract no. 0326501D. The authors should like to thank Mr. D. Bierwirth for his excellent technician work on this project, Dr. N. H. Cho for his help with the preparation of the plots and Mrs. R. Zschernitz for her expert typing of the text.     

Numerical prediction of turbulent boundary layer noise from a sharp-edged flat plate

An efficient hybrid uncorrelated wall plane waves–boundary element method (UWPW-BEM) technique is proposed to predict the flow-induced noise from a structure in low Mach number turbulent flow. Reynolds-averaged Navier-Stokes equations are used to estimate the turbulent boundary layer parameters such as convective velocity, boundary layer thickness, and wall shear stress over the surface of the structure. The spectrum of the wall pressure fluctuations is evaluated from the turbulent boundary layer parameters and by using semi-empirical models from literature. The wall pressure field underneath the turbulent boundary layer is synthesized by realizations of uncorrelated wall plane waves (UWPW). An acoustic BEM solver is then employed to compute the acoustic pressure scattered by the structure from the synthesized wall pressure field. Finally, the acoustic response of the structure in turbulent flow is obtained as an ensemble average of the acoustic pressures due to all realizations of uncorrelated plane waves. To demonstrate the hybrid UWPW-BEM approach, the self-noise generated by a flat plate in turbulent flow with Reynolds number based on chord Re_c = 4.9 × 10⁵ is predicted. The results are compared with those obtained from a large eddy simulation (LES)-BEM technique as well as with experimental data from literature.     

Receptivity of the boundary layer on a flat plate with a blunted leading edge to steady nonuniformity of the free stream

The flow past a flat plate with a blunted leading edge by a flow of a viscous incompressible fluid with a small spanwise-periodic, steady nonuniformity of the velocity profile is considered. Such a flow simulates the interaction of one type of vortex disturbances of a turbulent external flow with the boundary layer. The solution obtained predicts generation of strong disturbances in the boundary layer, which are similar to the streaky structure observed in the case of high free-stream turbulence. It is shown that the boundary-layer flow on blunted bodies is more sensitive to vortex disturbances than on a plate with a sharp leading edge. Central Aerohydrodynamic Institute, Zhukovskii, 140160. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 41, No. 4, pp. 93–100, July–August, 2000.     

DNS of a Laminar Separation Bubble in the Presence of Oscillating External Flow

A three-dimensional Direct Numerical Simulation (DNS) of a laminar separation bubble in the presence of oscillating flow is performed. The oscillating flow induces a streamwise pressure gradient varying in time. The special shape of the upper boundary of the computational domain, together with the oscillating pressure gradient causes the boundary layer flow to alternately separate and re-attach. When the inflow decelerates, the shear layer starts to separate and rolls up. Simultaneously the flow becomes 3D. After a transient period, the phase-averaged reverse flow inside the separation bubble reaches speeds ranging from 20 up to 150% of the free-stream velocity. During these phases, the flow is absolutely unstable and self-sustained turbulence can exist. When the inflow starts to accelerate, a spanwise roll of turbulent flow is shed from the shear layer. Shortly after this, the remainder of the separation bubble moves downstream and rejoins with the shed turbulent roll. During the flow-acceleration phase, a patch of laminar boundary layer flow is obtained. Along the flat plate, a series of turbulent patches of flow travelling downstream, separated by laminar flow can be observed, reminiscent of boundary layer flow in a turbine cascade with periodically appearing free-stream disturbances.     

An experimental investigation of the combined effects of surface curvature and streamwise pressure gradients both in laminar and turbulent flows

Flow and heat transfer characteristics over flat, concave and convex surfaces have been investigated in a low speed wind tunnel in the presence of adverse and favourable pressure gradients (k), for a range of –3.6 × 10^–6 ≤ k ≤ +3.6 × 10^–6. The laminar near zero pressure gradient flow, with an initial momentum thickness Reynolds number of 200, showed that concave wall boundary layer was thinner and heat transfer coefficients were almost 2 fold of flat plate values. Whereas for the same flow condition, thicker boundary layer and 35% less heat transfer coefficients of the convex wall were recorded with an earlier transition. Accelerating laminar flows caused also thinner boundary layers and an augmentation in heat transfer values by 28%, 35% and 16% for the flat, concave and convex walls at k = 3.6 × 10^–6. On the other hand decelerating laminar flows increased the boundary layer thickness and reduced Stanton numbers by 31%, 26% and 22% on the flat surface, concave and convex walls respectively. Turbulent flow measurements at k = 0, with an initial momentum thickness Reynolds number of 1100, resulted in 30% higher and 25% lower Stanton numbers on concave and convex walls, comparing to flat plate values. Moreover the accelerating turbulent flow of k = 0.6 × 10^–6 brought about 29%, 30% and 24% higher Stanton numbers for the flat, concave and convex walls and the decelerating turbulent flow of k = –0.6 × 10^–6 caused St to decrease up to 27%, 25% and 29% for the same surfaces respectively comparing to zero pressure gradient values. An empirical equation was also developed and successfully applied, for the estimation of Stanton number under the influence of pressure gradients, with an accuracy of better than 4%.     

Direct numerical simulation of the transition to turbulence in a supersonic boundary layer on smooth and rough surfaces

Direct numerical simulations of instability development and transition to turbulence in a supersonic boundary layer on a flat plate are performed. The computations are carried out for moderate supersonic (free-stream Mach number M = 2) and hypersonic (M = 6) velocities. The boundary layer development is simulated, which includes the stages of linear growth of disturbances, their nonlinear interaction, stochastization, and turbulent flow formation. A laminar–turbulent transition initiated by distributed roughness of the plate surface at the Mach number M = 2 is also considered.     

A bypass wake induced laminar/turbulent transition

The process of laminar to turbulent transition induced by a von Karman vortex street wake, was studied for the case of a flat plate boundary layer. The boundary layer developed under zero pressure gradient conditions. The vortex street was generated by a cylinder positioned in the free stream. An X-type hot-wire probe located in the boundary layer, measured the streamwise and normal to the wall velocity components. The measurements covered two areas; the region of transition onset and development and the region where the wake and the boundary layer merged producing a turbulent flow. The evolution of Reynolds stresses and rms-values of velocity fluctuations along the transition region are presented and discussed. From the profiles of the Reynolds stress and the mean velocity profile, a ‘negative' energy production region along the transition region, was identified. A quadrant splitting analysis was applied to the instantaneous Reynolds stress signals. The contributions of the elementary coherent structures to the total Reynolds stress were evaluated, for several x-positions of the near wall region. Distinct regions in the streamwise and normal to the wall directions were identified during the transition.     

The turbulent/non-turbulent interface at the outer boundary of a self-similar turbulent jet

The flow at the outer boundary of a submerged self-similar turbulent jet at Re=2᎒³ is investigated experimentally by means of combined particle image velocimetry (PIV) laser-induced fluorescence (LIF) measurements. The jet fluid contains a fluorescent dye so that the LIF data can be used to discriminate between the jet fluid and the ambient fluid. The axial velocity, Reynolds stress, and vorticity are determined relative to the jet boundary. The results are compared against the conventional profiles, and the results of a direct numerical simulation of the turbulent far-wake behind a flat plate. The results show a sharp transition between rotational and irrotational fluid at the fluid interface, and the existence of a layer of irrotational velocity fluctuations outside the turbulent region.     

Experimental study of boundary-layer transition on an airfoil induced by periodically passing wake

 Hot-wire measurements are performed in boundary-layer flows developing on a NACA 0012 airfoil over which wakes pass periodically. The periodic wakes are generated by rotating circular cylinders clockwise or counterclockwise around the airfoil. The time- and phase-averaged mean streamwise velocities and turbulence fluctuations are measured to investigate the phenomena of wake-induced transition. Especially, the phase-averaged wall shear stresses are evaluated using a computational Preston tube method. The passing wakes significantly change the pressure distribution on the airfoil, which has influence on the transition process of the boundary layer. The orientation of the passing wake alters the pressure distribution in a different manner. Due to the passing wake, the turbulent patches are generated inside the laminar boundary layer on the airfoil, and the boundary layer becomes temporarily transitional. The patches propagate downstream at a speed smaller than the free-stream velocity and merge together further downstream. Relatively high values of phase-averaged turbulence fluctuations in the outer part of the boundary layer indicate the possibility that breakdown occurs in the outer layer away from the wall. It is confirmed that the phase-averaged mean velocity profile has two dips in the outer region of the transitional boundary layer for each passing cycle. Received: 12 February 2001 / Accepted: 6 July 2001 Published online: 23 November 2001     

The interaction between a plane shear layer and a slender body

The interaction of a plane shear layer with a thin flat plate located in the nonlinear region of the shear layer has been investigated experimentally. The shear layer's velocity ratio is 0.375, and its Reynolds number is ΔUθ₀/μ = 625. It is found that for different angles of attack of the plate, the mixing layer is deflected toward the slower stream. In addition, the plate attenuates turbulent fluctuations of the shear layer structures.     

Experimental study of vortex structures in a hypersonic shock layer on a flat plate

The characteristics of travelling perturbations of density in a hypersonic shock layer on a flat plate for the Mach number M_∞=21 and unit Reynolds numberRe ₁=6·10⁵ m⁻¹ were experimentally studied by the method of electron-beam fluorescence. The perturbations were generated by interaction of the shock layer behind an oblique gas-dynamic whistle and the leading edge of the plate. The cases of unsteady and quasi-steady interaction were considered. In both cases, vortex disturbances of finite amplitude were generated. The measurements were performed at the fundamental frequency F=0.6·10⁻⁴ and at the harmonic; the streamwise phase velocities, the growth rates of the disturbances, and the angles of wave propagation were obtained. The measurement results are compared with some experimental data for subsonic flows, some particular results of the linear stability theory for compressible flows, and the results obtained on the basis of a simple model of the nonlinear stage of disturbance evolution in a hypersonic boundary layer. Institute of Theoretical and Applied Mechanics, Siberian Division, Russian Academy of Sciences, Novosibirsk 630090. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 40, No. 6, pp. 41–47, November–December, 1999.     

Spectral and instantaneous flow field characteristics of the laminar to turbulent transition in a cone and plate apparatus

Fluid-surface interaction, is very much influenced by the flow distribution and the flow spectra. For biological surfaces, cell functions such as mytosis and cell turnover, can be triggered by the instantaneous flow fluctuations which induce augmented shear stress levels inside the wall surface boundary layer. The objective of this work is to study the flow field along a cellular surface and to understand the interaction process. For that purpose, a cone and plate apparatus was built in which the transitional and turbulent instantaneous flow field characteristics, especially near the plate surface, were investigated using spatial hot wire anemometry, concentrating on time domain and spectral analysis. The frequency spectrum of velocity fluctuations near the plate is influenced by the plate roughness. We found that there is a linear relation between wall roughness and the preferred frequencies of the spectra. In addition a universal law exists for mean velocities, similar to the logarithmic law of the wall, when normalized by R˜ ^1/2, the apparatus Reynolds number. Received: 31 March 1998/Accepted: 11 January 1999     

金属丝壁面加热湍流标度律的实验研究

通过在固壁表面的平板湍流边界层沿流向平行放置若干通电加热的金属细丝,在平板表面形成沿展向周期性分布的温度场,利用该温度场引起的空气热对流,在湍流边界层近壁区域产生一组沿湍流边界层展向周期分布的流向涡结构。对壁湍流小尺度结构标度律统计特性的研究表明,金属丝加热后形成的规则流向涡结构将壁湍流各种尺度湍涡结构不规则的脉动有序地组织起来,增强了湍流小尺度结构的层次结构相似性,减小了壁湍流中小尺度结构的间歇性和奇异性,抑制了壁湍流中奇异的湍涡结构。     

Numerical Modeling of the Development of a Streaky Structure in a Boundary Layer at a High Freestream Turbulence Level

The disturbances generated by external turbulence in the boundary layer on a flat plate set suddenly in motion are determined. A turbulent flow calculated by direct numerical simulation is taken as the initial conditions. The solution obtained simulates the initial stage of laminar-turbulent transition in the flat-plate boundary layer at a high turbulence level in the oncoming flow. The solution makes it possible to estimate the effects of different factors, such as nonstationarity, nonlinearity, and the parameters of the freestream velocity fluctuation spectrum, on disturbance enhancement in the boundary layer.     

Experiments on localized disturbances in a flat plate boundary layer. Part 1. The receptivity and evolution of a localized free stream disturbance

The receptivity of a laminar boundary layer to free stream disturbances has been experimentally investigated through the introduction of deterministic localized disturbances upstream of a flat plate mounted in a wind tunnel. Hot-wire measurements indicate that the spanwise gradient of the normal velocity component (and hence the streamwise vorticity) plays an essential role in the transfer of disturbance energy into the boundary layer. Inside the laminar boundary layer the disturbances were found to give rise to the formation of longitudinal structures of alternating high and low streamwise velocity. Similar streaky structures exist in laminar boundary layers exposed to free stream turbulence, in which the disturbance amplitude increases in linear proportion to the displacement thickness. In the present study the perturbation amplitude of the streaks was always decaying for the initial amplitudes used, in contrast to the growing fluctuations that are observed in the presence of free stream turbulence. This points out the importance of the continuous influence from the free stream turbulence along the boundary layer edge.     

Statistical laws of the pressure fluctuations in a hypersonic turbulent boundary layer

The results of measuring the pressure fluctuations on the wall of the nozzle of a hypersonic wind tunnel beneath a developed turbulent boundary layer are presented for the Mach number M_∞ = 7.5. On the basis of a statistical analysis, it is shown that the action of the turbulent flow is dynamically similar to the propagation of a random sequence of wave packets with continuously distributed temporal and spatial scales. Low-frequency disturbances are associated with large-scale structures of long duration that propagate at a mean-statistical velocity similar in value to the outer flow velocity. The continuous generation of weakly-correlated small-scale disturbances ensuring the maintenance and development of turbulence occurs chiefly in the inner region of the boundary layer. Spectral estimates of the power generated by the turbulent flow in the wall region of the boundary layer are presented.     

The Effect of wake Turbulence Intensity on Transition in a Compressor Cascade

Direct numerical simulations of separating flow along a section at midspan of a low-pressure V103 compressor cascade with periodically incoming wakes were performed. By varying the strength of the wake, its influence on both boundary layer separation and bypass transition were examined. Due to the presence of small-scale three-dimensional fluctuations in the wakes, the flow along the pressure surface undergoes bypass transition. Only in the weak-wake case, the boundary layer reaches a nearly-separated state between impinging wakes. In all simulations, the flow along the suction surface was found to separate. In the simulation with the strong wakes, separation is intermittently suppressed as the periodically passing wakes managed to trigger turbulent spots upstream of the location of separation. As these turbulent spots convect downstream, they locally suppress separation.