Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Structure and properties of H<Subscript>8</Subscript>(PW<Subscript>11</Subscript>TiO<Subscript>39</Subscript>)<Subscript>2</Subscript>O heteropoly acid

Heteropoly acid (HPA) H₈(PW₁₁TiO₃₉)₂O·xH₂O (I) is synthesized by three different ways and studied by chemical analysis, potentiometric titration, mass-spectrometry, IR, ³¹P, ¹⁸³W, and ¹⁷O NMR spectroscopy, thermogravimetry, and transmission electron microscopy. Anion I consists of two subparticles of the Keggin structure bridged by Ti-O-Ti. The dimeric anion exists in HPA aqueous solutions at [I] > 0.02 M. At pH > 0.6 it splits to a [PW₁₁TiO₄₀]⁵⁻ monomer stable up to pH ∼ 6. When heated (150–400)°C, I splits into H₃PW₁₂O₄₀ and, apparently, H₃PW₁₀Ti₂O₃₈ without phase separation. Thermolysis products are soluble and when dissolved in water turn again into I. Complete decomposition of I to oxides occurs at ∼450°C.     

Electrical conductivity studies in the system Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript>-Li<Subscript>1.33</Subscript>Ti<Subscript>1.67</Subscript>O<Subscript>4</Subscript>

Electrical conductivity in the monoclinic Li₂TiO₃, cubic Li_1.33Ti_1.67O₄, and in their mixture has been studied by impedance spectroscopy in the temperature range 20–730 °C. Li₂TiO₃ shows low lithium ion conductivity, σ₃₀₀≈10^–6 S/cm at 300 °C, whereas Li_1.33Ti_1.67O₄ has 3×10^–8 at 20 °C and 3×10^–4 S/cm at 300 °C. Structural properties are used to discuss the observed conductivity features. The conductivity dependences on temperature in the coordinates of 1000/T versus log_e(σT) are not linear, as the conductivity mechanism changes. Extrinsic and intrinsic conductivity regions are observed. The change in the conductivity mechanism in Li₂TiO₃ at around 500–600 °C is observed and considered as an effect of the first-order phase transition, not reported before. Formation of solid solutions of Li_{2– x} Ti_{1+ x} O₃ above 900 °C significantly increases the conductivity. Irradiation by high-energy (5 MeV) electrons causes defects and the conductivity in Li₂TiO₃ increases exponentially. A dose of 144 MGy yields an increase in conductivity of about 100 times at room temperature. Electronic Publication     

Dielectric properties and I-V characteristics of (Pb<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>)TiO<Subscript>3</Subscript> thin films improved by TiO<Subscript>2</Subscript> buffer layers

A TiO₂ thin buffer layer was introduced between the (Pb_0.4Sr_0.6)TiO₃ (PST) film and the Pt/Ti/SiO₂/Si substrate in an attempt to improve their electrical properties. Both TiO₂ and PST layers were prepared by a chemical solution deposition method. It was found that the TiO₂ buffer layer increased the (100)/(001) preferred orientation of PST and decreased the surface roughness of the films, leading to an enhancement in electrical properties including an increase in dielectric constant and in its tunability by DC voltage, as well as a decrease in dielectric loss and leakage current density. At an optimized thickness of the TiO₂ buffer layer deposited using 0.02 mol/l TiO₂ sol, the 330-nm-thick PST films had a dielectric constant, loss and tunability of 1126, 0.044 and 60.7% at 10 kHz, respectively, while the leakage current density was 1.95 × 10⁻⁶ A/cm² at 100 kV/cm.     

Synthesis of multifunctional macroporous-mesoporous TiO<Subscript>2</Subscript>-bioglasses for bone tissue engineering

Hierarchical porous TiO₂-bioglasses (TiO₂-BGs) with the macropore with the size of 30–50 μm and the mesopore with the diameter of 4.4–5.6 nm have been synthesized through the evaporation-induced self-assembly method. The corn stalks were used as the macroporous template and P123 as the mesoporous template in the process. The chemical and physical properties of the hierarchical porous TiO₂-BGs before and after immersion in simulated fluid (SBF) were evaluated by X-ray diffraction, scanning electron microscope, Fourier transform infrared spectroscopy, nitrogen adsorption–desorption, and Energy dispersive spectrometer. The effect of TiO₂ content on the formation of surface hydroxyapatite and drug release profiles of the fabricated TiO₂-BGs in SBF were investigated in detail. It was found that macroporous-mesoporous TiO₂-bioglasses (MM TiO₂-BGs) exhibited a good ability of surface hydroxyapatite formation comparing with macroporous-mesoporous bioglasses. It took only 3 h for the MM TiO₂-BGs to be covered with the hydroxyapatite layer. It can be ascribed to the present of Ti–OH which may improve the spontaneous growth of apatite by consuming the calcium and phosphate ions from SBF. Additionally, MM TiO₂-BGs also showed good drug sustained release profiles. Therefore, the multifunctional MM TiO₂-BGs reported here could be a good candidate for application in bone tissue engineering.     

TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hybrid nanomaterials: synthesis and variable UV-blocking properties

Silica and core–shell structured titania/silica (TiO₂/SiO₂) nanoparticles with particles size ranging from tens to hundreds of nanometers were prepared and deposited onto cotton fabric substrates by sol–gel process. The morphologies of the nanoparticles were characterized by field-emission scanning electron microscope (FE-SEM). The photocatalytic decomposition properties as well as UV-blocking properties of the fabrics treated with SiO₂ and TiO₂/SiO₂ nanoparticles were investigated.     

The fabrication of TiO<Subscript>2</Subscript> nanoparticle/ZnO nanowire arrays bi-filmed photoanode and their effect on dye-sensitized solar cells

Porous TiO₂ nanoparticles coated on ZnO nanowire arrays (TiO₂ NP/ZnO NW) as photoanode for dye-sensitized solar cell (DSSC) has been fabricated and investigated to improve the power conversion efficiency. The TiO₂ NP/ZnO NW photoanode consists of single crystalline ZnO NWs synthesized via hydrothermal method and porous TiO₂ NP film covered on the surface of ZnO NW arrays by screen printing technique. The effect of TiO₂ NPs thickness of the bi-filmed photoanode on the cell performance has been investigated, and TiO₂ NP/ZnO NW DSSC with NP thickness of ~5 μm exhibits the best efficiency of 4.68%, higher than 1.16% of ZnO NW DSSC and 3.18% of TiO₂ NPs DSSC, prepared and tested under identical conditions. The efficiency increase is attributed to the enlarged photocurrent, due to the greatly enhanced surface area for dye absorption and light harvesting efficiency resulted from TiO₂ NPs, and improved open-circuit voltage, due to reduced electron recombination by providing direct conduction pathway along ZnO NWs.     

Photoinduced electron transfer in some photosensitive molecules-incorporated semiconductor/zeolites: New photocatalytic systems

An intramolecular charge transfer (ICT) molecule,p-N,N-dimethyl-aminobenzoic acid (DMABA) has been studied in zeolite and colloidal media. The ratio of ICT to normal emission (ICT/LE) is greatly enhanced in zeolites compared to that in polar solvents. The ICT emission of DMABA was quenched by increasing the concentration of TiO₂ colloids, while the normal emission was slightly enhanced. Upon illumination of the heteropoly acid (HPA) incorporated TiO₂ colloids, interfacial electron transfer takes place from the conduction band of TiO₂ to the incorporated HPA which is also excited to catalyze the photoreduction of Methyl Orange. It is found that the interfacial electron transfer mechanism of HPA/TiO₂ is quite analogous to the Z-scheme mechanism for plant photosynthetic systems. In DMABA-adsorbed TiO₂/Y-zeolite the ICT/LE ratio of DMABA is quite small implying that electron transfer takes place from DMABA to the conduction band of TiO₂. This results in drastic enhancement in the photocatalytic activity of DMABA-adsorbed TiO₂/Y-zeolite compared to free TiO₂/Y-zeolite.     

Preparation and photocatalytic activity of TiO<Subscript>2</Subscript> films with Ni nanoparticles

Titania thin films were synthesized by sol–gel dip-coating method with metallic Ni nanoparticles synthesized separately from an organometallic precursor Ni(COD)₂ (COD = cycloocta-1,5-diene) in presence of 1,3-diaminopropane as a stabilizer. Titania was obtained from a titanium isopropoxide precursor solution in presence of acetic acid. A Ni/TiO₂ sol system was used to coat glass substrate spheres (6, 4 and 3 mm diameter sizes), and further heat treatment at 400 °C was carried out to promote the crystallization of titania. XRD analysis of the TiO₂ films revealed the crystallization of the anatase phase. Transmission Electron Microscopy (TEM) and High Resolution TEM studies of Ni nanoparticles before mixing with the TiO₂ solution revealed the formation of Ni nanostructures with an average size of 5–10 nm. High-angle annular dark-field images of the Ni/TiO₂ system revealed well-dispersed Ni nanoparticles supported on TiO₂ and confirmed by AFM analysis. The photocatalytic activity of the Ni/TiO₂ films was evaluated in hydrogen evolution from the decomposition of ethanol using a mercury lamp for UV light irradiation. Titania films in presence of Ni nanoparticles show higher efficiency in their photocatalytic properties in comparison with TiO₂.     

Preparation and characterization of poly(phthalazinone ether ketone)/SiO<Subscript>2</Subscript> hybrid composite thin films with low friction coefficient

Organic–inorganic poly(phthalazinone ether ketone) (PPEK)/SiO₂ hybrid composite thin films were prepared by the dip-coating method on pre-cleaned glass substrates. The covalent bonds between organic and inorganic phases were introduced by an in-situ O-acylation reaction of isocyanatopropyltriethoxysilane (ICPTES) with the borohydride-reduced PPEK forming a polymer bearing triethoxysilyl groups. Theses groups were subsequently hydrolyzed with tetraethoxysilane (TEOS) and allowed to form a network via a sol–gel process. The polymer hybrid composite exhibited good thermal stability and a higher glass transition temperature as compared with the pure resin. Atomic force microscope, water contact angle measurement and scanning electron microscope were used to characterize the polymer hybrid thin films. The tribological experiment showed that the films have very low friction coefficient (about 0.1) and good anti-wear properties, without failure even after sliding for 18,000 s under modest loads. The improved tribological properties of the modified substrate were attributed to good adherence of PPEK/SiO₂ hybrid films on the substrate and synergy of both PPEK matrix and silica particles.     

Transparent poly(methyl methacrylate)/TiO<Subscript>2</Subscript> nanocomposites for UV-shielding applications

Transparent poly(methyl methacrylate) (PMMA)/TiO₂ nanocomposites have been prepared by solution mixing PMMA with organically soluble titania xerogel. The organically soluble titania xerogel in the form of amorphous phase has been synthesized via a simple sol-gel method, involving hydrolysis of tetrabutyl titanate (TBT) in trifluoroacetic acid (TFA) and gelation. The obtained PMMA/TiO₂ nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), thermogravimetry (TG) and ultraviolet-visible (UV-vis) absorption spectroscopy. The results showed that the interaction between titania nanoparticles and PMMA macromolecular chains led to a homogeneous dispersion of TiO₂ in PMMA matrix. The resulting PMMA/TiO₂ nanocomposites showed improved thermal stability, high transparency and high UV-shielding efficiency with a small amount of titania xerogel (≤3.0 wt %). The present work is of interest for developing a series of transparent UV-shielding nanocomposites.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

DSC investigation of nanocrystalline TiO<Subscript>2</Subscript> powder

The aim of the article is to investigate the influence of particle size on titanium dioxide phase transformations. Nanocrystalline titanium dioxide powder was obtained through a hydrothermal procedure in an aqueous media at high pressure (in the range 25–100 atm) and low temperature (≤200 °C). The as-prepared samples were characterized with respect to their composition by ICP (inductive coupled plasma), structure and morphology by XRD (X-ray diffraction), and TEM (transmission electron microscopy), thermal behavior by TG (thermogravimetry) coupled with DSC (differential scanning calorimetry). Thermal behavior of nanostructured TiO₂ was compared with three commercial TiO₂ samples. The sequence of brookite–anatase–rutile phase transformation in TiO₂ samples was investigated. The heat capacity of anatase and rutile in a large temperature range are reported.     

Electrochemical determination of <Emphasis Type="Italic">p</Emphasis>-cresol using mesoporous TiO<Subscript>2</Subscript>-modified carbon paste electrode

A mesoporous TiO₂ (meso-TiO₂) was synthesized, and used to prepare modified carbon paste electrode (CPE). The electrochemical sensing properties were characterized using K₃[Fe(CN)₆], showing that meso-TiO₂ modified CPE possesses larger surface area and higher electron transfer rate. The electrochemical behavior of p-cresol was investigated. At the meso-TiO₂ modified CPE, the oxidation peak current of p-cresol remarkably increases, and the oxidation peak potential shifts negatively, suggesting that meso- TiO₂ exhibits highly efficient catalytic activity to the oxidation of p-cresol. Based on this, a sensitive, rapid and convenient electrochemical method was developed for the detection of p-cresol. The linear range is from 1.5 × 10⁻⁷ and 2.0 × 10⁻⁵ mol l⁻¹, and the limit of detection is as low as 8.0 × 10⁻⁸ mol l⁻¹. Finally, the new method was successfully used to determine p-cresol in water samples.     

Evaluation of the structural,optical and photocatalytic properties of nitrogen-fluorine co-doped TiO<Subscript>2</Subscript> thin films

Nanostructured TiO₂ films were synthesized by a modified sol–gel method using Pluronics P-123 (EO₂₀PO₇₀EO₂₀) as templating agent, titanium n-butoxide [Ti(OC₄H₉)₄] as inorganic precursor, and ammonium fluoride (NH₄F) as the source of N and F dopant atoms in order to prepare sols of x(NF) TiO₂ (x=2, 5, 10, 20 wt%). The thin film preparation was made by spin coating, followed by calcination at 400 °C. The as-prepared TiO₂ and xNF-TiO₂ films were characterized by XRD, Raman spectroscopy, FTIR, TGA-DTA, SEM, UV–Vis diffuse reflectance spectroscopy and EPR. XRD and Raman spectroscopy show that the crystalline structure of these samples consists exclusively of the anatase phase. The band gap (E _g ) values for the doped 10 and 20 NF-TiO₂ film systems were found to be significantly smaller than those corresponding to the rest of the other TiO₂ films. The photocatalytic properties of these films are investigated by following the degradation of methyl orange in aqueous solution under UV irradiation. The photodecomposition is mainly a direct function of the amount of NF present in the TiO₂ matrix. The 20NF-TiO₂ sample shows the highest activity of all the samples studied.     

Effect of oxygen mobility in the lattice of Au/TiO<Subscript>2</Subscript> on formaldehyde oxidation

Two Au catalysts supported on TiO₂ were prepared by impregnation method followed by sodium borohydride reduction or calcination in air (Au/TiO₂-R and Au/TiO₂-C, respectively). The 1 wt % Au/TiO₂-R sample was found to be highly efficient for the oxidation of low concentrated formaldehyde at room temperature. A HCHO conversion of 98.5% was achieved with this catalyst, whereas the Au/TiO₂-C sample showed almost no activity under the same conditions. Highly dispersed metallic Au nanoparticles with small size (∼3.5 nm) were identified in the 1 wt % Au/TiO₂-R catalyst. A significant negative shift of Au4f peak in XPS spectra with respect to bulk metallic Au was observed for the 1 wt % Au/TiO₂-R but no similar phenomena was found for the heat-treated catalyst. More Au nanoparticles and higher content of surface active oxygen were identified on the surface of the Au/TiO₂-R in comparison with the Au/TiO₂-C, suggesting that the Au/TiO₂-R catalyst can enhance the amount of active sites and species involved in for HCHO oxidation. The reduction treatment by sodium borohydride promotes the formation of dispersed metallic Au nanoparticles with small size because it facilitates the electron transfer and increases the content of surface Au nanoparticles and activated oxygen. All these factors are responsible for a high activity of this catalyst in the oxidation of HCHO.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Influence of ThO<Subscript>2</Subscript> on the photocatalytic activity of TiO<Subscript>2</Subscript>

Microcomposites consisting of TiO₂ (or Ce-doped TiO₂) and ThO₂ (0.5–2% of the TiO₂ mass) are produced by sol-gel synthesis of TiO₂ in presence of ThO₂. X-ray diffraction study reveals the effects of ThO₂ (compared to the ThO₂-free TiO₂, obtained by the same method) on the anatase interplanar distances, crystallites size and phase composition. The photocatalytic tests in presence of the composites under UV irradiation reveal an increase of the Malachite Green degradation rate constant. The effect depends on the Th relative content, temperature of annealing of the catalyst and addition of other doping agent. The highest photocatalytic activity is observed for TiO₂ obtained at 550°C and containing 1% ThO₂. The composite exhibits activity in dark, also. The presence of Ce⁴⁺ ions is not an obligatory requirement for the realization of the ThO₂ effect. The reported results suggest that the radioactivity of the Th and/or its decay products is one of the main factors responsible for the increased photocatalytic activity of TiO₂.