Cu分隔开的Pd单原子用于乙炔选择加氢:Cu担载量的影响

大量乙烯中少量乙炔的去除是化工生产中的重要过程之一,理想途径是将其选择加氢生成乙烯.负载型Pd催化剂因具有很高的乙炔转化率而被广泛用于该过程,但乙烯选择性很低,同时会使原料气中的乙烯被加氢,造成原料气的浪费.采用其它元素对Pd纳米粒子表面修饰,覆盖部分活性位,可以在一定程度上提高乙烯选择性,但是会大大降低Pd的利用率.因此,制备兼具高活性和高选择性且经济实用的催化剂,仍是这一过程亟待解决的主要问题之一.我们的前期工作中,将Pd与IB族金属(Au,Ag,Cu)分别结合制备得到了一系列含Pd的合金单原子催化剂(SAC),发现它们在大量乙烯存在条件下的乙炔选择加氢反应中表现出优异的催化性能.其中,Pd的用量仅为ppm级别,大大提高了Pd的利用率.作为IB族最为廉价的金属,Pd与Cu形成的合金SAC在提高Pd原子利用率的同时,能够进一步降低催化剂的经济成本.然而,当形成合金SAC时,Cu/Pd原子比例的极限值仍然不确定.本文通过固定Pd的担载量,采用简单的等体积共浸渍的方法,制备了一系列不同Cu/Pd原子比例的氧化硅负载的双金属催化剂.首先,我们采用程序升温还原(TPR)和X射线衍射(XRD)对催化剂的还原能力和双金属纳米粒子的尺寸进行了考察.进一步,采用X射线吸收光谱(XAS,包括EXAFS和XANES)对双金属催化剂中Pd的配位环境进行了分析.最后,结合它们在大量乙烯存在条件下的乙炔选择加氢反应中的催化性能,对形成合金SAC时Cu/Pd原子比例进行了讨论.TPR结果显示,Cu与Pd结合时会促进双金属纳米粒子的还原.XRD结果表明,随着Cu含量的降低,双金属纳米粒子的尺寸明显减小.XANES结果证实,当Pd与Cu结合时,Pd会带有部分负电荷,这也与Pd的电负性大于Cu相一致.通过对EXAFS拟合结果进行分析,我们发现当Cu/Pd的原子比例≥40/1时,Pd原子可以被Cu原子完全分隔开,形成含Pd的合金SAC,使其在大量乙烯存在条件下的乙炔选择加氢反应中表现出优异的催化性能.通过对还原温度的考察,我们发现还原温度由250 oC升高到400 oC时,对同一催化剂的催化性能影响不大;EXAFS拟合结果显示,对比分别经过250和400 oC还原后的催化剂,Pd的配位环境变化不明显,这可能是导致催化性能相似的主要原因.     

负载型Pd/TiO2和Pd-Ag/TiO2催化剂的乙炔选择性加氢催化性能

利用程序升温还原(TPR)、X-射线衍射(XRD)、CO吸附-红外光谱(CO-IR)、电子顺磁共振(EPR)和微型催化反应评价等手段, 研究了负载Pd/γ-Al2O3, Pd/TiO2和Pd-Ag/TiO2催化剂的结构和乙炔选择性加氢催化性能. 结果表明, Pd/TiO2催化剂具有较Pd/γ-Al2O3催化剂更优良的乙炔选择性加氢催化性能, 这与Pd-TiO2之间的强相互作用密切相关. Pd-TiO2之间的强相互作用不仅使负载型钯金属催化剂具有较高的乙炔加氢催化选择性, 而且具有较高的乙炔加氢催化活性. Pd/TiO2催化剂中添加Ag 组分后, Pd金属可促进Ag+的还原并可能形成Pd-Ag合金, 催化剂的乙烯选择性虽有所增加, 但乙炔转化率和乙烯收率下降.     

Cu分隔开的Pd单原子用于乙炔选择加氢:Cu担载量的影响（英文）

大量乙烯中少量乙炔的去除是化工生产中的重要过程之一,理想途径是将其选择加氢生成乙烯.负载型Pd催化剂因具有很高的乙炔转化率而被广泛用于该过程,但乙烯选择性很低,同时会使原料气中的乙烯被加氢,造成原料气的浪费.采用其它元素对Pd纳米粒子表面修饰,覆盖部分活性位,可以在一定程度上提高乙烯选择性,但是会大大降低Pd的利用率.因此,制备兼具高活性和高选择性且经济实用的催化剂,仍是这一过程亟待解决的主要问题之一.我们的前期工作中,将Pd与IB族金属(Au,Ag,Cu)分别结合制备得到了一系列含Pd的合金单原子催化剂(SAC),发现它们在大量乙烯存在条件下的乙炔选择加氢反应中表现出优异的催化性能.其中,Pd的用量仅为ppm级别,大大提高了Pd的利用率.作为IB族最为廉价的金属,Pd与Cu形成的合金SAC在提高Pd原子利用率的同时,能够进一步降低催化剂的经济成本.然而,当形成合金SAC时,Cu/Pd原子比例的极限值仍然不确定.本文通过固定Pd的担载量,采用简单的等体积共浸渍的方法,制备了一系列不同Cu/Pd原子比例的氧化硅负载的双金属催化剂.首先,我们采用程序升温还原(TPR)和X射线衍射(XRD)对催化剂的还原能力和双金属纳米粒子的尺寸进行了考察.进一步,采用X射线吸收光谱(XAS,包括EXAFS和XANES)对双金属催化剂中Pd的配位环境进行了分析.最后,结合它们在大量乙烯存在条件下的乙炔选择加氢反应中的催化性能,对形成合金SAC时Cu/Pd原子比例进行了讨论.TPR结果显示,Cu与Pd结合时会促进双金属纳米粒子的还原.XRD结果表明,随着Cu含量的降低,双金属纳米粒子的尺寸明显减小.XANES结果证实,当Pd与Cu结合时,Pd会带有部分负电荷,这也与Pd的电负性大于Cu相一致.通过对EXAFS拟合结果进行分析,我们发现当Cu/Pd的原子比例≥40/1时,Pd原子可以被Cu原子完全分隔开,形成含Pd的合金SAC,使其在大量乙烯存在条件下的乙炔选择加氢反应中表现出优异的催化性能.通过对还原温度的考察,我们发现还原温度由250 oC升高到400 oC时,对同一催化剂的催化性能影响不大;EXAFS拟合结果显示,对比分别经过250和400 oC还原后的催化剂,Pd的配位环境变化不明显,这可能是导致催化性能相似的主要原因.     

密度泛函理论计算研究表面应力对钯催化乙炔选择性加氢活性与选择性的影响（英文）

在石油催化裂解过程中,除了生成乙烯、丙烯及丁烯等烯烃,还会产生部分炔烃.目前工业上通常采用炔烃选择性加氢转化为对应的单烯烃,以除去其中炔烃.由于产品烯烃中的炔烃等杂质含量需极低,这就对用于加氢催化剂的活性和选择性提出了很高的要求,即催化剂需要选择性吸附炔烃并加氢,而不损失其中的烯烃.经过前期大量的基础研究工作,目前工业中炔烃选择性加氢应用最广泛的催化剂是负载型钯基催化剂.然而,单独的钯金属选择性并不理想,因而对其选择性以及活性进行调控成为了当前关注的研究课题.本文采用密度泛函理论计算结合微观反应动力学模拟手段,研究了钯金属表面应力存在条件下的活性与选择性,以及形成次表层物种的可能性和形成后的活性与选择性.研究发现,改变钯金属的晶格参数与表面应力,反应物、表面反应中间体和产物的吸附能都会产生相应的变化,且吸附能与晶格参数的变化存在线性关系,晶格参数越大,吸附越强.利用表面反应过渡态能量与初始态能量之间的线性关系,相应的乙炔加氢生成乙烯的反应速率可以通过微观反应动力学模拟得到.结果显示,不同晶格参数的钯催化剂催化乙炔加氢生成乙烯的反应活性位于相应火山型曲线的强吸附侧,即减弱乙炔和氢的吸附强度可提高乙烯的生成速率.在此基础上,本文研究了不同表面应力的钯催化剂在次表面吸附不同覆盖度碳原子和氢原子的情况,发现晶格参数越大越有利于碳原子和氢原子在次表面的吸附.同时,研究发现在次表面碳掺杂的条件下,不同表面应力条件下的钯催化剂的活性均有所增强.此外,由于乙烯在所有研究的钯催化剂表面脱附比进一步加氢容易,因而乙烯都可以选择性生成.     

甲醇水蒸气重整制氢Pd/ZnO催化剂还原过程中Pd与ZnO的相互作用

 采用程序升温还原、程序升温脱附、程序升温电导及X射线衍射研究了并流共沉淀法制备的15.9%Pd/ZnO催化剂还原过程中结构和物种的变化及电荷的传递,考察了还原温度对该催化剂催化甲醇水蒸气重整制氢的影响. 结果表明,还原过程中Pd与ZnO间存在明显的相互作用,导致氢溢流,溢流氢促进了ZnO还原并使ZnO与Pd形成活性中心PdZn合金. 催化剂的还原历程为 PdO/ZnO → Pd/ZnO → PdZnO1-x/ZnO → 无定形PdZn合金/ZnO → 晶型PdZn合金/ZnO. 并流共沉淀法制备的Pd/ZnO催化剂Pd分散度高, PdZn合金形成温度低. 在523～573 K还原后,催化剂的PdZn合金粒径为5～14 nm, 此时催化剂对甲醇的转化率及二氧化碳选择性均达到最大值.     

IB金属对Ni/SiO2催化剂乙炔选择性加氢反应性能的影响

乙烯是合成聚乙烯的原料,其主要来源是石油裂解气,其中少量的乙炔杂质会严重毒化生产聚乙烯的催化剂,因此需要将其去除.对于乙炔选择加氢反应,传统工业上使用的是Pd基催化剂,尽管其乙炔转化率很高,但对乙烯的选择性很低.我们前期的研究发现,IB族金属(Au,Ag和Cu)与Pd形成的合金单原子催化剂可以有效地提高乙烯的选择性.作为与Pd同组的非贵金属,Ni催化剂在多种催化加氢反应中显示出优异活性,而在乙炔选择加氢反应中,Ni是否能够替代贵金属Pd尚无定论.本文系统地研究了IB金属对Ni/SiO2催化剂乙炔选择性加氢性能的影响.与Pd/SiO2催化剂不同,单金属Ni/SiO2催化剂在低温下不具有活性.将IB金属添加到Ni/SiO2催化剂中,可以显著提高其催化活性以及对乙烯的选择性.其中,AuNix/SiO2和CuNix/SiO2催化剂的催化活性随还原温度升高而提高,而AgNix/SiO2催化剂对预处理温度不敏感.通过调变IB/Ni原子比和还原温度优化了催化剂的催化性能,发现优化后的三种催化剂(CuNi0.125/SiO2、AgNi0.5/SiO2和AuNi0.5/SiO2)的活性和选择性随反应温度升高表现出相似的变化趋势.催化稳定性考察结果显示,CuNi0.125/SiO2催化剂表现出最高选择性和稳定性;尽管AuNi0.5/SiO2的初始活性最高,但是稳定性最低.采用XRD、TPR和微量吸附量热等表征手段对不同IB金属对Ni基催化剂性质的影响进行了系统考察.以Cu-Nix/SiO2催化剂为例,H2-TPR测试结果表明,Cu-Ni双金属纳米颗粒的形成使得还原温度低于相应的单金属催化剂,表明铜和镍之间存在明显的相互作用.此外,通过TPR获得的CuNix/SiO2催化剂上的氢气消耗量与理论耗氢量相吻合,表明在还原处理的过程中双金属催化剂中的CuO和NiO可以被完全还原.乙炔的微量吸附量热结果表明,在CuNi0.125/SiO2,AgNi0.5/SiO2,AuNi0.5/SiO2和Ni0.5/SiO2催化剂上的初始吸附热分别为187,196,304和103 kJ/mol,即它们的初始乙炔吸附强度顺序为AuNi0.5/SiO2>AgNi0.5/SiO2>CuNi0.125/SiO2>Ni0.5/SiO2.该结果与三者的初始催化活性顺序一致,表明IB金属的加入可以增强乙炔在催化剂表面的吸附,从而提高催化活性.     

IB金属对Ni/SiO_2催化剂乙炔选择性加氢反应性能的影响（英文）

乙烯是合成聚乙烯的原料,其主要来源是石油裂解气,其中少量的乙炔杂质会严重毒化生产聚乙烯的催化剂,因此需要将其去除.对于乙炔选择加氢反应,传统工业上使用的是Pd基催化剂,尽管其乙炔转化率很高,但对乙烯的选择性很低.我们前期的研究发现,IB族金属(Au,Ag和Cu)与Pd形成的合金单原子催化剂可以有效地提高乙烯的选择性.作为与Pd同组的非贵金属,Ni催化剂在多种催化加氢反应中显示出优异活性,而在乙炔选择加氢反应中,Ni是否能够替代贵金属Pd尚无定论.本文系统地研究了IB金属对Ni/SiO_2催化剂乙炔选择性加氢性能的影响.与Pd/SiO_2催化剂不同,单金属Ni/SiO_2催化剂在低温下不具有活性.将IB金属添加到Ni/SiO_2催化剂中,可以显著提高其催化活性以及对乙烯的选择性.其中,Au Ni_x/SiO_2和CuNi_x/SiO_2催化剂的催化活性随还原温度升高而提高,而AgNi_x/SiO_2催化剂对预处理温度不敏感.通过调变IB/Ni原子比和还原温度优化了催化剂的催化性能,发现优化后的三种催化剂(Cu Ni_(0.125)/SiO_2、AgNi_(0.5)/SiO_2和AuNi_(0.5)/SiO_2)的活性和选择性随反应温度升高表现出相似的变化趋势.催化稳定性考察结果显示,CuNi_(0.125)/SiO_2催化剂表现出最高选择性和稳定性;尽管Au Ni_(0.5)/SiO_2的初始活性最高,但是稳定性最低.采用XRD、TPR和微量吸附量热等表征手段对不同IB金属对Ni基催化剂性质的影响进行了系统考察.以Cu-Ni_x/SiO_2催化剂为例,H_2-TPR测试结果表明,Cu-Ni双金属纳米颗粒的形成使得还原温度低于相应的单金属催化剂,表明铜和镍之间存在明显的相互作用.此外,通过TPR获得的CuNi_x/SiO_2催化剂上的氢气消耗量与理论耗氢量相吻合,表明在还原处理的过程中双金属催化剂中的CuO和NiO可以被完全还原.乙炔的微量吸附量热结果表明,在CuNi_(0.125)/SiO_2,AgNi_(0.5)/SiO_2,Au Ni_(0.5)/SiO_2和Ni_(0.5)/SiO_2催化剂上的初始吸附热分别为187,196,304和103 kJ/mol,即它们的初始乙炔吸附强度顺序为Au Ni_(0.5)/SiO_2AgNi_(0.5)/SiO_2CuNi_(0.125)/SiO_2Ni_(0.5)/SiO_2.该结果与三者的初始催化活性顺序一致,表明IB金属的加入可以增强乙炔在催化剂表面的吸附,从而提高催化活性.     

Pt在MgAl2O4载体上的分散程度对催化苯甲醛加氢反应影响

构建催化剂特别是在亚纳米尺度下分散的贵金属催化剂的构效关系是多相催化研究领域中的主要任务之一.我们采用与金属Pt具有强相互作用的MgAl2O4尖晶石作为载体,通过简单浸渍法制备了在纳米、亚纳米和单原子尺度上分散的Pt催化剂.首先利用X射线衍射和原子分辨的球差校正电镜,确定了Pt在MgAl2O4尖晶石载体表面上随负载量增大逐渐形成孤立的和相邻的单原子Pt,然后逐渐形成无定形Pt聚集体和小晶粒;然后利用电感耦合等离子体光谱和CO化学吸附测定了催化剂中Pt的含量和分散度;进一步通过测定CO在Pt表面吸附的红外光谱,区分了载体表面单原子和金属颗粒表面原子的CO吸附特征结构,并据此对不同结构的Pt原子进行了半定量估算.考察了具有不同Pt分散结构的Pt/MgAl2O4催化剂的催化苯甲醛选择性加氢能力,发现以载体表面Pt单原子物种为主的催化剂,可在较宽的温度区间内保持较高的部分加氢产物苯甲醇的选择性(60–150oC,苯甲醇选择性99.4–97.9％,甲苯选择性～0.4％),而以Pt纳米颗粒为主的催化剂上苯甲醇选择性降低显著,同时生成较多深度加氢产物甲苯(60–150oC,苯甲醇选择性99.0–93.1％,甲苯选择性0.7–5.0％).此外,我们测定了各催化剂在不同转化率(～20–90％)时催化剂加氢反应的质量比活性和转化频率(TOF),并在较低苯甲醛转化率(～20％)时,估算了不同结构Pt物种对苯甲醛加氢反应的本征活性,发现Pt纳米颗粒表面原子比MgAl2O4载体表面Pt单原子本征活性更高(4807 h–1 versus 3277 h–1).综上,Pt单原子催化剂具有贵金属原子利用率高,本征活性和加氢选择性高等优点;Pt纳米催化剂表面原子深度加氢能力强,加氢选择性较差,虽本征活性更高,但不足以补偿贵金属原子利用率降低带来的活性损失,Pt质量比活性显著低于单原子催化剂.此外,MgAl2O4尖晶石负载的单原子Pt催化剂也具有良好的催化反应循环稳定性,是一种较为理想的催化苯甲醛选择性加氢制苯甲醇催化剂.     

利用ZnO@ZIF-8核壳结构构建高选择性、高稳定性的Pd/ZnO催化剂用于CO_2加氢制甲醇（英文）

近年来由于环境问题CO_2加氢制甲醇催化反应重新回归为研究热点。对于Pd/ZnO催化剂,研究表明PdZn合金相是制甲醇反应的活性中心,而单独Pd利于CO生成。为了实现Pd和ZnO的充分接触,本工作以一种ZnO@ZIF-8核壳型结构为载体负载Pd纳米颗粒后经由高温煅烧制得PZZ8-T催化剂(T为不同煅烧温度),同时制备了ZnO纳米棒负载Pd的PZ催化剂作为对比。在随后的CO_2加氢反应中,相比于PZ,PZZ8-T展现出极高的甲醇选择性。之后我们通过一系列表征探究了催化剂的构效关系,发现催化剂的甲醇选择性与表面Pd的化学态有关,更多的Pd以PdZn合金的形式存在将会带来更高的甲醇选择性。XPS O 1s谱图和EPR分析表明CO_2的活化与催化剂表面的氧空穴和ZnO极性面含量直接相关。而化学吸附手段进一步对Pd-ZnO界面进行了表征,揭示了其与CO_2转化速率的关联。本工作的意义在于,一是展现了利用新材料制备更优的传统催化剂的方法,二是通过表面分析手段加深了对催化剂构效关系的理解。     

SiO2负载的Au-Ni双金属催化剂在乙炔选择加氢反应中的应用

负载型Au催化剂在乙炔选择加氢反应中表现出很高的乙烯选择性,但其转化率相对较低.通过添加第二种金属如Pd,Fe,Ag和Cu等,制备双金属催化剂是提高其在加氢反应中催化活性的一种非常有效的手段.其中Au-Pd双金属催化剂是最受关注的体系之一,Pd的加入可以非常显著地提高其催化乙炔选择加氢反应的活性.据文献报道,与Pd同一主族的Ni也具有较好的加氢活性.尽管与Pd相比,Ni很难与Au形成合金,但目前已有Au-Ni双金属催化剂在多种反应中表现出协同效应的报道,如水气变换、CO氧化以及芳香硝基化合物选择加氢等.因此,向Au催化剂中添加Ni也可能提高催化剂在乙炔选择加氢反应中的催化活性.因此,我们采用两步法制备了一系列SiO2负载的具有不同Ni:Au原子比的Au-Ni双金属催化剂,并将其用于乙炔选择加氢反应,发现Au-Ni双金属催化剂在该反应中表现出了显著的协同效应,其活性明显优于相应单金属催化剂的活性.尽管其乙烯选择性略低于单金属Au催化剂,但明显高于单金属Ni催化剂.通过调节还原温度和/或Ni:Au的比例,对催化剂的性能进行了优化.结果显示,当Ni:Au=0.5时,催化剂表现出最优的综合性能,即兼具较高的乙炔转化率和乙烯选择性.为了研究Au-Ni双金属催化剂中金属纳米粒子的结构、组成以及Au-Ni之间的相互作用,我们对催化剂进行了X射线衍射(XRD)、高分辨透射电镜(HRTEM)、能量散射谱(EDS)以及原位红外光谱(DRIFTS)表征.XRD和TEM结果显示,催化剂中的Au-Ni双金属纳米粒子都具有高分散和粒径均匀的特点.通过EDS分析,发现在Au-Ni双金属催化剂中的单个金属纳米粒子同时含有Au和Ni两种元素,尽管每个纳米粒子中Ni:Au的比例有差异.HRTEM结果发现,Au-Ni双金属纳米粒子的晶格间距介于Au(111)和Ni(111)的晶面间距之间,说明在Au-Ni双金属催化剂中有Au-Ni合金形成.原位DRIFTS结果显示,在Au-Ni双金属催化剂中,Au的存在促进了Ni的还原,说明Au与Ni之间存在紧密的相互作用.综上可见,Au和Ni在乙炔选择加氢反应中所表现出的协同效应主要归功于Au-Ni合金的形成,其中金属态Ni起主要的活性作用,而Au的存在则提高了催化剂的乙烯选择性.     

ZnO纳米线负载Pd1单原子催化剂催化若干反应性能的考察

将孤立的Pd原子分散到ZnO纳米线(NWs)上作为单原子催化剂(SACs),并考察了它们在若干反应中的催化性能.Pd1/ZnO SAC对甲醇蒸汽重整制氢反应表现出高的活性、稳定性和CO2选择性.该催化剂体系对CO和H2的氧化也具有高活性,但在富氢物料中CO优先氧化反应中的催化剂性能较差,这主要是由于在ZnO负载的Pd1原子上H2氧化的强竞争反应所致.常压下在Pd1/ZnO SAC上就可发生逆水汽变换反应.该系列催化反应测试结果清楚地表明,选择合适金属与载体对开发分子催化转化用单原子催化剂至关重要.     

Supported Intermetallic PdZn Nanoparticles as Bifunctional Catalysts for the Direct Synthesis of Dimethyl Ether from CO‐Rich Synthesis Gas

The single‐step syngas‐to‐dimethyl ether (STD) process entails economic and technical advantages over the current industrial two‐step process. Pd/ZnO‐based catalysts have recently emerged as interesting alternatives to currently used Cu/ZnO/Al₂O₃ catalysts, but the nature of the active site(s), the reaction mechanism, and the role of Pd and ZnO in the solid catalyst are not well established. Now, Zn‐stabilized Pd colloids with a size of 2 nm served as the key building blocks for the methanol active component in bifunctional Pd/ZnO‐γ‐Al₂O₃ catalysts. The catalysts were characterized by combining high‐pressure operando X‐ray absorption spectroscopy and DFT calculations. The enhanced stability, longevity, and high dimethyl ether selectivity observed makes Pd/ZnO‐γ‐Al₂O₃ an effective alternative system for the STD process compared to Cu/ZnO/γ‐Al₂O₃.     

Chemoselective hydrogenation method catalyzed by Pd/C using diphenylsulfide as a reasonable catalyst poison

While Pd/C is one of the most useful catalysts for hydrogenation, the high catalyst activity of Pd/C causes difficulty in its application to chemoselective hydrogenation between different types of reducible functionalities. In order to achieve chemoselective hydrogenation using Pd/C, we investigated catalyst poison as a controller of the catalyst activity. We found that the addition of Ph₂S (diphenylsulfide) to the Pd/C-catalyzed hydrogenation reaction mixture led to reasonable deactivation of Pd/C. By the use of the Pd/C-Ph₂S catalytic system, olefins, acetylenes, and azides can be selectively reduced in the coexistence of aromatic carbonyls, aromatic halides, cyano groups, benzyl esters, and N-Cbz (benzyloxycarbonyl) protecting groups. The present method is promising as a general and practical chemoselective hydrogenation process in synthetic organic chemistry.     

利用ZnO@ZIF-8核壳结构构建高选择性、高稳定性的Pd/ZnO催化剂用于CO2加氢制甲醇

Catalytic CO₂ hydrogenation to methanol is a promising route to mitigate the negative effects of anthropogenic CO₂. To develop an efficient Pd/ZnO catalyst, increasing the contact between Pd and ZnO is of the utmost importance, because "naked" Pd favors CO production via the reverse water-gas shift path. Here, we have utilized a ZnO@ZIF-8 core-shell structure to synthesize Pd/ZnO catalysts via Pd immobilization and calcination. The merit of this method is that the porous outer layer can offer abundant "guest rooms" for Pd, ensuring intimate contact between Pd and the post-generated ZnO. The synthesized Pd/ZnO catalysts (PZZ8-T, T denotes the temperature of calcination in degree Celsius) is compared with a ZnO nanorod-immobilized Pd catalyst (PZ). When the catalytic reaction was performed at lower reaction temperatures (250, 270, and 290 ℃), the highest methanol space time yield (STY) and highest STY per Pd achieved by PZ at 290 ℃ were 0.465 g g_cat^-1 h^-1 and 13.0 g g_Pd^-1 h^-1, respectively. However, all the PZZ8-T catalysts exhibited methanol selectivity values greater than 67.0% at 290 ℃, in sharp contrast to a methanol selectivity value of 32.8% for PZ at the same temperature. Thus, we performed additional investigations of the PZZ8-T catalysts at 310 and 360 ℃, which are unusually high temperatures for CO₂ hydrogenation to methanol because the required endothermic reaction is expected to be severely inhibited at such high temperatures. Interestingly, the PZZ8-T catalysts were observed to achieve a methanol selectivity value of approximately 60% at 310 ℃, and PZZ8-400 was observed to maintain a methanol selectivity value of 51.9% even at a temperature of 360 ℃. Thus, PZZ8-400 attains the highest methanol STY of 0.571 g g_cat^-1 h^-1at 310 ℃. For a better understanding of the structure-performance relationship, we characterized the catalysts using different techniques, focusing especially on the surface properties. X-ray photoelectron spectroscopy (XPS) results indicated a linear relationship between the methanol selectivity and the surface PdZn : Pd ratio, proving that the surface PdZn phase is the active site for CO₂ hydrogenation to methanol. Furthermore, analysis of the XPS O 1s spectrum together with the electronic paramagnetic resonance results revealed that both, the oxygen vacancy as well as the ZnO polar surface, played important roles in CO₂ activation. Chemisorption techniques provided further quantitative and qualitative information regarding the Pd-ZnO interface that is closely related to the CO₂ conversion rate. We believe that our results can provide insight into the catalytic reaction of CO₂ hydrogenation from the perspective of surface science. In addition, this work is an illustrative example of the use of novel chemical structures in the fabrication of superior catalysts using a traditional formula.     

Pd/Amberlyst-45催化剂催化水相中苯酚选择性加氢制环己酮(英文)

环己酮是重要的有机化工原料和工业溶剂,是制造尼龙、己内酰胺和己二酸的主要中间体,环己酮的绿色生产工艺受到人们关注.目前全世界环己酮年产量接近900万吨,但环己酮生产仍主要以环己烷为原料,采用富氧空气氧化为环己基过氧化氢,再在铬酸叔丁酯催化剂作用下分解为环己醇和环己酮的混合物,然后经一系列蒸馏精制后得到环己酮、工艺复杂、能耗高,而且设备腐蚀、环境污染及安全问题严重.因此,大量工作正致力于新工艺和新催化剂研究,其中光催化氧化、分子筛催化氧化和金属氧化物催化氧化等都有相关报道,同时还有学者开发了其它环己酮制备新方法,如环己烯水合法、苯加氢法、环己醇氧化法和苯酚加氢法等.苯酚直接选择性加氢合成环己酮研究具有重要意义.苯酚加氢通常有两种工艺,气相加氢和液相加氢,由于液相加氢具有无需将反应物汽化、能耗较低和催化剂反应活性高等优势而受到广泛关注.但是目前大量文献报道的苯酚加氢过程仍需要高温条件且较易产生环己醇和环己烷等副产物,大部分催化反应需在有机溶剂中进行,因此如何提高环己酮选择性,减小环境影响成为近年来的热门课题.在过去数年中,人们筛选了大量催化剂,其中Pd催化剂具有较高活性和目的产物选择性,因为其对羰基表现出较低的催化活性.研究还发现,催化剂载体对苯酚加氢产物分布有重要影响,酸性载体或酸性助剂的加入均能提高苯酚转化率和环己酮选择性,可能的原因是催化剂表面可与苯酚羟基形成O-H…π强相互作用,使苯酚分子更容易吸附在载体表面,而一旦苯酚经催化加氢生成环己酮,由于失去羟基与载体表面相互作用,环己酮更容易从载体表面脱附,从而避免过度加氢生成环己醇,同时酸性位点可以增强Pd的电子密度,提高催化加氢活性.另外,通过添加助剂也可有效改善催化剂性能.然而,到目前为止,通过单一的一种催化剂仍然很难同时实现苯酚的高转化率和环己酮的高选择性.因此,开发新催化剂和简便的生产工艺对环己酮高效高质量生产具有重要意义.本文使用一种多孔、不易溶解的酸性离子交换树脂Amberlyst-45(A-45)为载体,采用简单的浸渍工艺制备了一系列不同Pd负载量的Pd/A-45催化剂,详细考察了催化剂在水相中对苯酚选择性加氢制环己酮的催化活性和选择性,包括反应温度、催化剂用量、反应时间和Pd负载量等对反应活性的影响及催化剂重复使用情况,并且与传统的SiO_2,ZnO,MgO,Al_2O_3和活性炭负载的Pd催化剂进行对比.研究发现,Pd/A-45催化剂在温和反应条件(40-100℃,0.2-1 MPa)下具有极高的催化活性和选择性,在适宜的反应条件下苯酚转化率达到100%,环己酮选择性高于89%.进一步分析由不同活性金属负载量制备的不同粒径Pd/A-45催化剂的活性规律发现,苯酚加氢生成环己酮是一个结构敏感型反应,其中Pd颗粒尺寸为12-14 nm时更有利于环己酮生成.     

A Single‐Atom Iridium Heterogeneous Catalyst in Oxygen Reduction Reaction

Combining the advantages of homogeneous and heterogeneous catalysts, single‐atom catalysts (SACs) are bringing new opportunities to revolutionize ORR catalysis in terms of cost, activity and durability. However, the lack of high‐performance SACs as well as the fundamental understanding of their unique catalytic mechanisms call for serious advances in this field. Herein, for the first time, we develop an Ir‐N‐C single‐atom catalyst (Ir‐SAC) which mimics homogeneous iridium porphyrins for high‐efficiency ORR catalysis. In accordance with theoretical predictions, the as‐developed Ir‐SAC exhibits orders of magnitude higher ORR activity than iridium nanoparticles with a record‐high turnover frequency (TOF) of 24.3 e^? site^?1 s^?1 at 0.85 V vs. RHE) and an impressive mass activity of 12.2 A mg^?1_Ir, which far outperforms the previously reported SACs and commercial Pt/C. Atomic structural characterizations and density functional theory calculations reveal that the high activity of Ir‐SAC is attributed to the moderate adsorption energy of reaction intermediates on the mononuclear iridium ion coordinated with four nitrogen atom sites.     

无表面活性剂条件下一锅法制备金属/氧化锌复合材料用于催化二氧化碳加氢制甲醇反应

Catalytic hydrogenation of CO₂ to methanol is an important chemical process owing to its contribution in alleviating the impacts of the greenhouse effect and in realizing the requirement for renewable energy sources. Owing to their excellent synergic functionalities and unique optoelectronic as well as catalytic properties, transition metal/ZnO (M/ZnO) nanocomposites have been widely used as catalysts for this reaction in recent years. Development of size-controlled synthesis of metal/oxide complexes is highly desirable. Further, because it is extremely difficult to achieve the strong-metal-support-interaction (SMSI) effect when the M/ZnO nanocomposites are prepared via physical methods, the use of chemical methods is more favorable for the fabrication of multi-component catalysts. However, because of the requirement for an extra H₂ reduction step to obtain the active metallic phase (M) and surfactants to control the size of nanoparticles, most M/ZnO nanocomposites undergo two- or multi-step synthesis, which is disadvantageous for the stable catalytic performance of the M/ZnO nanocomposites. In this work, we demonstrate facile one-pot synthesis of M/ZnO (M = Pd, Au, Ag, and Cu) nanocomposites in refluxed ethylene glycol as a solvent, without using any surfactants. During the synthesis process, Pd and ZnO species can stabilize each other from further aggregation by reducing their individual surface energies, thereby achieving size control of particles. Besides, NaHCO₃ serves as a size-control tool for Pd nanoparticles by adjusting the alkaline conditions. Ethylene glycol serves as a mild reducing agent and solvent owing to its capacity to reduce Pd ions to generate Pd crystals. The nucleation and growth of Pd particles are achieved by thermal reduction, while the ZnO nanocrystals are formed by thermal decomposition of Zn(OAc)₂. X-ray diffraction patterns of the M/ZnO and ZnO were analyzed to study the phase of the nanocomposites, and the results show that no impurity phase was detected. Transmission electron microscopy (TEM) was used to study the morphology and structural properties. In addition, X-ray photoelectron spectroscopy analysis was performed to further confirm the formation of M/ZnO hybrid materials, and the results confirm SMSI between Pd and ZnO. Inductively coupled plasma mass spectrometry was used to check the actual elemental compositions, and the results show that the detected atomic ratios of Pd/Zn were consistent with the values in the theoretical recipe. To investigate the effects of the Pd/Zn molar ratios and the added amount of NaHCO₃ on Pd size, the average sizes of Pd particles were calculated, and the results were confirmed by TEM observation. The Cu/ZnO/Al₂O₃ composite is a widely known catalyst for hydrogenation of CO₂ to methanol, and other M/ZnO composites are also catalytic for this reaction. Therefore, different M/ZnO hybrids were further studied as catalysts for hydrogenation of CO₂ to methanol, among which Pd/ZnO (1 : 9) demonstrated the best performance (30% CO₂ conversion, 69% methanol selectivity, and 421.9 g_methanol·(kg catalyst·h)^-1 at 240 ℃ and 5 MPa. The outstanding catalytic performance may be explained by the following two factors: first, Pd is a good catalyst for the dissociation of H₂ to give active H atoms, and second, SMSI between Pd and ZnO favors the formation of surface oxygen vacancies on ZnO. Moreover, most M/ZnO composites exhibit excellent performance in methanol selectivity, especially the Au/ZnO catalyst, which has the highest methanol selectivity (82%) despite having the lowest CO₂ conversion. Hopefully, this work would provide a simple route for synthesis of M/ZnO nanocomposites with clean surfaces for catalysis.     

A Durable Nickel Single‐Atom Catalyst for Hydrogenation Reactions and Cellulose Valorization under Harsh Conditions

Hydrothermally stable, acid‐resistant nickel catalysts are highly desired in hydrogenation reactions, but such a catalyst remains absent owing to the inherent vulnerability of nickel under acidic conditions. An ultra‐durable Ni‐N‐C single‐atom catalyst (SAC) has now been developed that possesses a remarkable Ni content (7.5 wt %) required for practical usage. This SAC shows not only high activities for hydrogenation of various unsaturated substrates but also unprecedented durability for the one‐pot conversion of cellulose under very harsh conditions (245 °C, 60 bar H₂, presence of tungstic acid in hot water). Using integrated spectroscopy characterization and computational modeling, the active site structure is identified as (Ni‐N4)???N, where significantly distorted octahedral coordination and pyridinic N constitute a frustrated Lewis pair for the heterolytic dissociation of dihydrogen, and the robust covalent chemical bonding between Ni and N atoms accounts for its ultrastability.     

Pd/C(en) catalyzed chemoselective hydrogenation in the presence of aryl nitriles

Aromatic nitriles are not only important components of natural products, pharmaceuticals, herbicides and agrochemicals but also a synthetic equivalent of various functionalities. The development of synthetic methods of aromatic nitriles have been increasing in terms of its usefulness. Since aromatic nitriles are susceptible to the hydrogenation, it has been desired for the development of chemoselective hydrogenation method with retention of nitrile groups. Pd/C is one of the most popular catalysts for hydrogenation and many of reducible functional groups such as multiple bonds, benzyl ethers, N-Cbzs, nitro groups and so on could be easily reduced under the conditions. Therefore, it is very difficult to achieve the chemoselective hydrogenation of substrates containing two or more reducible functional groups. We have found that a Pd/C catalyst formed an isolable complex with ethylenediamine (en) employed as catalytic poison, and the complex [Pd/C(en)] catalyzed chemoselective hydrogenation of a variety of reducible functionalities distinguishing O-benzyl, N-Cbz and O-TBDMS protective groups, benzyl alcohols and epoxides. In the course of these investigations, we found the aryl nitriles could survive under the Pd/C(en)-catalyzed hydrogenation conditions in THF whose choice is important for the effective suppression. This methodology could be applied to the selective hydrogenation of alkene and alkyne functionalities in the presence of aromatic nitrile.