Interaction of Natural and Modified β-Cyclodextrins with a Biological Membrane Model of Dipalmitoylphosphatidylcholine

Lipid vesicles made up of dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) were used as a biological membrane model to investigate the interaction between natural and modified β-cyclodextrins and these membrane bilayers. Differential scanning calorimetry was used to study the thermotropic behavior of the DPPC vesicles and any change caused by the presence of cyclodextrins. The presence of dimethyl-β-cyclodextrin (DM-β-CyD) triggered a reduction in the enthalpy values related to the main transition peak from gel state to liquid crystal phase of DPPC aqueous dispersions, as a function of the DM-β-CyD molar fraction: the larger the amount of DM-β-CyD, the greater the reduction in ΔHvalues. This effect was probably due to the ability of DM-β-CyD to extract and to complex the DPPC molecules forming the phospholipid vesicles. The presence of β-cyclodextrin (β-CyD) or hydroxypropyl-β-cyclodextrin (HP-β-CyD) caused no particular alteration in the thermotropic parameters of DPPC vesicles, whereas trimethyl-β-cyclodextrin (TM-β-CyD) at molar fractions higher than 0.12 caused broadening of the transition peak due to a possible interaction with the hydrophobic part of the bilayers. Experiments on DPPC–cholesterol (10 mol%) vesicles showed the capability of β-CyD and TM-β-CyD to extract cholesterol from the ordered bilayer structures, triggering an alteration in the lipid constituents of the membranes. HP-β-CyD caused no variation in the thermotropic parameters of the DPPC–cholesterol (10 mol%) vesicles. The findings show that HP-β-CyD seems the most suitable molecular drug carrier forin vivoadministration.     

Vesicle—vesicle interaction and forces between bilayers in phospholipid systems incorporating phosphatidylinositol

Sonicated vesicles have been prepared from mixtures of dipalmitoylphosphatidylcholine (DPPC) and phosphatidylinositol (PI) covering a range of composition. The effect of temperature on the rates of aggregation of the vesicles on addition of calcium and magnesium ions has been investigated. Apart from pure PI vesicles the rates of aggregation decrease dramatically as the temperature approaches the gel-to-liquid crystalline phase transition temperature of DPPC. Low angle X-ray analysis of lamellar phases of DPPC-PI (75:25 wt%) in the presence of Ca²⁺ ions shows that between 35 and 45°C the repeat distance goes from 136 to 68 Å. It is suggested that below the chain-melting temperature of DPPC Ca²⁺ ions induce lateral phase separation of PI giving a lamellar repeat distance corresponding to the thickness of two bilayers.The net repulsive pressure between DPPC-PI bilayers has been measured by a vapour pressure technique as a function of temperature. At close apposition (<15 Å) the pressure is characteristic of hydration repulsion and increases with temperature. The repulsive force between the bilayers, lateral pressure and compressibility of the bilayers have also been determined. On progressively removing water from between the bilayers 5–14% of the work done goes into bilayer deformation, the remaining 86–95% being required to bring the bilayers together.     

Bilayer swelling of nonionic surfactant and sodium dodecylsulfate mixed system by refractive-index matching

Bilayer swelling behavior of nonionic and anionic surfactant mixed aqueous solution induced by adding glycerin was studied. The phenomenon were performed on a system, polyethylene glycol ether of tridecyl alcohol with the average number of ethylene oxide of 5 (CH₃(CH₂)₁₂(OCH₂CH₂)₅OH; abbreviation IT5) and SDS mixed aqueous solution, with white cream of the upper phase and micelles (L₁) of the lower phase. White cream containing densely packed multilamellar vesicles was revealed by freeze-fracture transmission electron microscopy and polarized microscope observations. Phase transition from white cream/L₁, two-phase, to clear unique vesicle phase can be induced by adding glycerin to replace water. The addition of glycerin lowers the turbidity of the dispersion and swells the interlamellar distance between bilayers, which could be explained by refractive-index matching between solvent and bilayers.     

Liquid Ordered Phase of Binary Mixtures Containing Dipalmitoylphosphatidylcholine and Sterols

The effect of cholesterol, desmosterol, stigmasterol, sitosterol, ergosterol, and androsterol on the phase behavior of aqueous dispersions of dipalmitoylphosphatidylcholine (DPPC) was studied to understand the role of the side chain in the formation of ordered phases of the type observed in membrane rafts. Thermotropic changes in the structure of mixed dispersions and transition enthalpies were examined by synchrotron X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The observations indicated that cholesterol was more efficient than phytosterols (stigmasterol and sitosterol) or ergosterol in its interaction with DPPC to form the liquid ordered phase (L_o). The L_o induced by cholesterol or desmosterol was stable over a wide temperature range, whereas, the liquid ordered phase containing phytosterols or ergosterol was profoundly dependent on temperature, which should be distinguished as L_oβ and L_oα, representing the phases below and above the main transition temperature. The characteristics in forming ordered structures of cholesterol and other sterols imply that the evolution may have selected cholesterol as the most efficient sterol for animals to form rafts in their cell membranes.     

Double-Chain Cationic Surfactants: Swelling,Structure, Phase Transitions and Additive Effects

Double-chain amphiphilic compounds, including surfactants and lipids, have broad significance in applications like personal care and biology. A study on the phase structures and their transitions focusing on dioctadecyldimethylammonium chloride (DODAC), used inter alia in hair conditioners, is presented. The phase behaviour is dominated by two bilayer lamellar phases, L_β and L_α, with “solid” and “melted” alkyl chains, respectively. In particular, the study is focused on the effect of additives of different polarity on the phase transitions and structures. The main techniques used for investigation were differential scanning calorimetry (DSC) and small- and wide-angle X-ray scattering (SAXS and WAXS). From the WAXS reflections, the distance between the alkyl chains in the bilayers was obtained, and from SAXS, the thicknesses of the surfactant and water layers. The L_α phase was found to have a bilayer structure, generally found for most surfactants; a L_β phase made up of bilayers with considerable chain tilting and interdigitation was also identified. Depending mainly on the polarity of the additives, their effects on the phase stabilities and structure vary. Compounds like urea have no significant effect, while fatty acids and fatty alcohols have significant effects, but which are quite different depending on the nonpolar part. In most cases, L_β and L_α phases exist over wide composition ranges; certain additives induce transitions to other phases, which include cubic, reversed hexagonal liquid crystals and bicontinuous liquid phases. For a system containing additives, which induce a significant lowering of the L_β–L_α transition, we identified the possibility of a triggered phase transition via dilution with water.     

Hydrogels from phospholipid vesicles

It is shown that phospholipid dispersions with a few percent of diacylphosphocholine PC in water can be swollen to single-phase lyotropic liquid crystalline L_α-phases by the addition of co-solvents like glycerol, 1,3-butyleneglycol BG or 1,2-propyleneglycol PG. The birefringent L_α-phases contain small unilamellar and multilamellar vesicles if the temperature of the samples is above the Krafft-Temperature T_m of the phospholipid. When such transparent birefringent viscous samples are cooled down below T_m the samples are transformed into birefringent gels. Cryo-TEM and FF-TEM measurements show that the bilayers of the vesicles are transformed from the liquid to the crystalline state during the transformation while the vesicle structure remains. The bilayers of the crystalline vesicles form adhesive contacts in the gel. Pulsed-field gradient NMR measurements show that two different kinds of water or co-solvent can be distinguished in the gels. One type of solvent molecules can diffuse like normal solvent in a continuous bulk phase. A second type of water diffuses much more slowly. This type of solvent is obviously trapped in the vesicles. The permeability of the crystalline vesicles for water and solvent molecules is much lower in the crystalline state than in the fluid state.     

The perturbing effect of cholesterol on the interaction between labdanes and DPPC bilayers

Differential scanning calorimetry (DSC) was used to study the effect of cholesterol on the perturbation of DPPC bilayers induced by eight bioactive structurally related labdanes isolated from the resin ‘ladano’ of Cistus creticus subsp. creticus (Cistaceae) or semisynthesized from the mother compounds. Labdanes themselves induced profound modifications in DPPC bilayer organization and thermotropic properties that were altered when cholesterol was incorporated in equimolar amounts to the labdanes. The present work shows that, up to 10 mol% of the equimolar mixture of cholesterol and the labdanes, the modifications evoked on DPPC bilayer organization are in accordance to these induced by the labdanes themselves. When the concentration exceeded 20 mol%, cholesterol influence dominated while the effect of the labdanes was suppressed and their interaction with the bilayer was probably prevented. The degree by which cholesterol modulated the labdane interaction with the bilayer depended on their structural characteristics that determine their localization in the bilayer interior. Polar groups that force the labdanes to localize themselves at the interfacial region broadened the concentration range by which labdanes interacted with the DPPC bilayer even in the presence of high concentration of cholesterol where cholesterol-rich domains are preferentially formed. On the other hand, labdanes possessing functional groups that promote their deeper penetration in the bilayer interior compete with cholesterol in a high extent for the same localization sites resulting in their possible elimination from the bilayer when the concentration of cholesterol present exceeds the 20 mol%.     

Self-Assembly of a Peptide Amphiphile Containing l-Carnosine and Its Mixtures with a Multilamellar Vesicle Forming Lipid

The self-assembly of the peptide amphiphile (PA) hexadecyl-(β-alanine-histidine) is examined in aqueous solution, along with its mixtures with multilamellar vesicles formed by DPPC (dipalmitoyl phosphatidylcholine). This PA, denoted C(16)-βAH, contains a dipeptide headgroup corresponding to the bioactive molecule l-carnosine. It is found to self-assemble into nanotapes based on stacked layers of molecules. Bilayers are found to coexist with monolayers in which the PA molecules pack with alternating up-down arrangement so that the headgroups decorate both surfaces. The bilayers become dehydrated as PA concentration increases and the number of layers in the stack decreases to produce ultrathin nanotapes comprised of 2-3 bilayers. Addition of the PA to DPPC multilamellar vesicles leads to a transition to well-defined unilamellar vesicles. The unique ability to modulate the stacking of this PA as a function of concentration, combined with its ability to induce a multilamellar to unilamellar thinning of DPPC vesicles, may be useful in biomaterials applications where the presentation of the peptide function at the surface of self-assembled nanostructures is crucial.     

Three-phase cyanate ester composites with fumed silica and negative-CTE reinforcements

Three-phase cyanate ester adhesives have been developed using a bisphenol E cyanate ester resin, fumed silica, and negative-CTE (coefficient of thermal expansion) reinforcements: short carbon fiber or zirconium tungstate (ZrW₂O ₈ ). Fumed silica was used to impart thixotropic behavior on the resin and decrease settling in the adhesives. The cured composites were evaluated using various thermal analysis techniques for their thermal-mechanical properties. Composites with short carbon fiber showed enhanced modulus and decreased thermal expansion (70% reduction for 20 vol%) and showed little phase separation. While settling of the dense ceramic particles could not be completely eliminated for the zirconium tungstate composites through rheological modification of the adhesive with added fumed silica, a reduction in CTE of 84% was achieved in the composite (58 vol%) compared to the neat resin. In addition, the effect of thermal history on the cure and temperature induced ZrW₂O₈ phase transitions, and their corresponding influence on thermal strains vs. temperature, are examined by thermomechanical analysis.     

CuI/L-Proline-Catalyzed Synthesis of Vinyl Sulfides in 95% Alcohol

A method for the synthesis of vinyl sulfides using the simple CuI/L-proline as a catalyst system is reported. The best yields were obtained in the 95% ethanol with 10 mol% CuI, 20 mol% L-proline, and 1.2 equiv of K₂CO₃. The amino acids act as base and excellent promoter for the copper-catalyzed coupling reactions, and this protocol tolerates both aromatic and heterocyclic thiols and avoids using other expensive additives.     

二维压缩系数研究二十二酸Langmuir膜的相态转变特征

本文采用二维压缩系数研究了二十二酸Langmuir膜的相态转变特征。通过相态转变前后压缩系数的变化特点,发现二十二酸单分子膜存在两种相变类型。第一类是当相变从L2态到L2’态时,压缩系数曲线出现一个峰值,然而相变前后的压缩系数不变,bi=bf。第二类是当相变从L2’态到S态时,压缩系数陡降,压缩系数曲线出现一个台阶。第一类相变可能的机理是在缓慢压缩过程中分子有自发性的重新排列过程,而第二类相变则是主要依赖于外力的持续压缩,被动性的分子自组装过程,bi>bf。     

Adsorption behaviors of DPPC/MO aggregates on SiO2 surfaces

The adsorption kinetics of extruded 1,2-dipalmitoyl- sn-glycero-3-phosphatidylcholine (DPPC)/1-(cis-9-octadecenoyl)- rac-glycerol (monoolein, MO) aggregates on SiO 2 surface at 25 degrees C is investigated in real time, using the dissipative quartz crystal microbalance (QCM) technique. Four adsorption pathways have been identified depending on the molar fraction of MO in the DPPC/MO system: (I) intact vesicle adsorption, (II) vesicle reorganization on a SiO 2 surface, (III) supported lipid bilayer (SLB) formation, and (IV) cubosome adsorption. The results can be understood by the fact that DPPC is a lamellar phase-forming lipid, whereas MO prefers the cubic phase. Therefore, the incorporation of MO in DPPC increases the packing parameter. Equally important, MO also increases the mobility of lipid molecules and lateral pressure in the bilayers as a result of the presence of a unique cis- double bond. Before extrusion, the vesicles size increases with the MO content when X MO or= 0.8. The extruded DPPC/MO suspensions consist of reformed vesicles for X MO or= 0.8, all with a uniform diameter of approximately 100 nm. Differential scanning calorimetry (DSC) further indicates that the addition of MO lowers the main phase transition temperature of DPPC and thus makes the hydrophobic interior more fluid.     

Effect of pressure on the Prodan fluorescence in bilayer membranes of phospholipids with varying acyl chain lengths

The fluorescence spectra of 6-propionyl-2-(dimethylamino)naphthalene (Prodan) were observed as a function of pressure for the bilayer membrane systems of dilauroylphosphatidylcholine (DLPC), dimyristoylphosphatidylcholine (DMPC), dipalmitoylphosphatidylcholine (DPPC), and distearoylphosphatidylcholine (DSPC). The wavelength of the emission maximum, lambdamax, was found to be 480, 430, and 500 nm for the liquid crystalline (Lalpha), ripple gel (P'beta), and pressure-induced interdigitated gel (LbetaI) phase, respectively. Since the lambdamax reflects the solvent property around the probe molecules, we could speculate on the location of the Prodan molecules in the bilayer membranes; in the Lalpha phase of the lipid bilayer, the Prodan molecules distribute around the phosphate of the lipids (i.e. the polar region). The Lalpha/P'beta phase transition caused the Prodan molecules to move into the less polar region near the glycerol backbone. The fluorescence intensity of the Prodan in the P'beta phase was dependent on the chain length of the lipids and on pressure; the shorter the chain length of the lipid, the stronger the fluorescence intensity of the Prodan. Moreover, for the DLPC bilayer membrane system, the fluorescence intensity at 430 nm increased with increasing pressure, indicating that the partition of Prodan into the DLPC bilayer membrane is promoted by applying pressure. In the case of the DPPC and DSPC bilayers, as the pressure increased further, the pressure-induced interdigitation caused the Prodan molecules to squeeze out of the glycerol backbone region and to move the hydrophilic region near the bilayer surface. The ratio of fluorescence intensity at 480 nm to that at 430 nm, F480/F430, showed a sharp change at the phase-transition pressure. In the case of the DPPC and DSPC bilayers, the values of F480/F430 showed an abrupt increase above a certain pressure higher than the Lalpha/P'beta transition pressure, which corresponds to the interdigitation from the P'beta to the LbetaI phase. The plot of F480/F430 versus pressure is available for recognition of the bilayer phase transitions, especially the bilayer interdigitation.     

Studies on outer-sphere electron transfer reactions of surfactant–cobalt(III) complexes with iron(II) in liposome (dipalmitoylphosphotidylcholine) vesicles

The effect of unilamellar vesicles of dipalmitoylphosphotidylcholine (DPPC), both below and above the phase transfer region, on the second-order rate constants for outer-sphere electron transfer between Fe²⁺ and the surfactant?Ccobalt(III) complexes, cis-[Co(en)₂(C₁₂H₂₅NH₂)₂]³⁺ and cis-[Co(trien)(C₁₂H₂₅NH₂)₂]³⁺ (en?=?ethylenediamine, trien?=?triethylenetetramine, C₁₂H₂₅NH₂?=?dodecylamine) was studied by UV?CVis absorption spectroscopy. Below the phase transition temperature of DPPC, the rate decreased with increasing concentration of DPPC, while above the phase transition temperature the rate increased with increasing concentration of DPPC. It is concluded that below the phase transition temperature, there is an accumulation of surfactant?Ccobalt(III) complexes at the interior of the vesicle membrane through hydrophobic effects, and above the phase transition temperature the surfactant?Ccobalt(III) complex is released from the interior to the exterior surface of the vesicle. Through isokinetic plots, we have established that the mechanism of the reaction does not alter during the phase transition of DPPC.     

Blockable Zn10L15 Ion Channels through Subcomponent Self‐Assembly

Metal–organic anion channels based on Zn₁₀L₁₅ pentagonal prisms have been prepared by subcomponent self‐assembly. The insertion of these prisms into lipid membranes was investigated by ion‐current and fluorescence measurements. The channels were found to mediate the transport of Cl⁻ anions through planar lipid bilayers and into vesicles. Tosylate anions were observed to bind and plug the central channels of the prisms in the solid state and in solution. In membranes, dodecyl sulfate blocked chloride transport through the central channel. Our Zn₁₀L₁₅ prism thus inserts into lipid bilayers to turn on anion transport, which can then be turned off through addition of the blocker dodecyl sulfate.     

Phase behaviour of polymer-grafted DPPC membranes for drug delivery systems design

Summary DPPC dispersions containing DPPE with attached PEG of molecular masses 350, 2000 and 5000 were investigated by DSC in order to determine their phase behaviour and potential use as drug delivery systems. In comparison with previously obtained ESR data, DSC provided a definition of the lipid composition and temperature at which the vesicles are in a liquid crystalline phase. For DPPC DPPE-PEG 350 the composition range is at molar fractions 0&lt;_&khgr;PEG350&lt;0.5.For DPPC DPPE-PEG 2000 the range of applicability is 0&lt;_{&khgr;PEG2000}&lt;0.07 and for DPPC/DPPE-PEG 5000 system it is 0&lt;_{&khgr;PEG5000}&lt;0.05.     

Photoinduced electron transfer of chlorophyll in lipid bilayer system

Photoinduced electron transfer from chlorophyll-a throughtheinterface of dipalmitoylphosphatidylcholine (DPPC) headgroup of the lipid bilayers was studied with electron magnetic resonance (EMR). The photoproduced radicals were identified with electron spin resonance (ESR) and radical yields of chlorophyll-a were determined by double integration ESR spectra. The formation of vesicles was identified by changes in measured λ_max values from diethyl ether solutions to vesicles solutions indirectly, and observed directly with SEM and TEM images. The efficiency of photosynthesis in model system was determined by measuring the amount of chlorophyll-a radical yields which were obtained from integration of ESRspectra.     

Phase equilibria and structures in ternary systems of a cationic surfactant (C16 TABr or (C16 TA)2SO4), alcohol,and water

The dependence of alcohol chain length on the isothermal phase behavior of the ternary systems hexadecylrrimethylammonium bromide/alcohol/water has been investigated. A liquid crystalline phase (the normal hexagonal one) occurs in the phase diagrams along the surfactant/water axis and this phase extends in the interior of the diagrams.When the alcohol is methanol, ethanol or butanol, there is in the ternary phase diagram a continuous solution region from the water to the alcoholic corner, and in the butanol case, in addition, a small region of lamellar liquid crystalline phase in the interior of the diagram. When the alcohol chain length is increased, the continuous solution region is divided into two subregions, an aqueousL ₁ and an alcoholicL ₂. The lamellar phase occupies the center of the phase diagrams and has the capability to incorporate large amounts of water under one-dimensional swelling. On the alcoholic side of the lamellar phase occur a reversed hexagonal liquid crystalline phase and a cubic liquid crystalline phase in the octanolic system; in the decanolic system the cubic phase is missing, but instead another liquid crystalline phase, presumably with rod-structure, occurs in addition to the reversed hexagonal phase.In a decanolic system where the monovalent bromide ion is replaced by the divalent sulphate ion there are the same solution regionsL ₁ andL ₂, and phase regions with liquid crystalline normal hexagonal and lamellar structures. The lamellar phase has lost much of its capability of incorporating water. That is in analogy with the conditions in anionic systems where the counterion charge has been increased. There is no reversed hexagonal phase, but on the alcoholic side of the lamellar phase, there is the same foreign liquid crystalline phase with a presumed rod-structure as in the monovalent system.     

Complexation of new active antibacterial adamantan derivatives with β CD: Preparation and characterization of complexes study of the thermotropic properties of pure and complex form with dipalmitoyl phosphatidylcholine bilayers

-Cyclodextrin (CD) complexes of I1-8, I1-10, I1-12, were prepared, isolated and characterized in solid and liquid form. Their thermotropic effects were studied by inserting them in DPPC bilayers both in pure and complexed forms. The results have shown that the presence of I1-8 causes spliting, broadening and lowering of the phase transition of DPPC bilayers. Their effects are more significant when I1-0 and I1-12 are inserted. These differential effects are eliminated when the above studied three molecules are incorporated in a complex form with CD in DPPC bilayers. The obtained results suggest that the bromine salts in the bilayer are likely to remain in the complex form rather than released in the membrane.     

Sintering behavior and thermal expansion of zirconia–titanium composites

The dilatometric and thermogravimetric methods were used to investigate the sintering conditions of 3Y–ZrO₂ and 3Y–ZrO₂–Ti composites. For the materials preparation, the nanometric zirconia stabilized by 3 mol% Y₂O₃ powder and micrometric titanium powder (3 and 10 vol%) were used. The green body samples were formed by slip casting method. The morphology of samples microstructures was determined by SEM observations. The stereological analysis of zirconia and zirconia–titanium composites was carried out using computer program. The density was measured using the Archimedes method. The hardness of sinters was also investigated. Addition of Ti into ZrO₂ influenced the sintering behavior and thermal expansion of obtained composites. The analysis of the sintering process and characteristic temperatures confirmed the increase of onset and final temperature of shrinkage with the increase in Ti content. The changes of the thermal expansion curves for the pure zirconia and 3Y–ZrO₂–Ti composites were the result of the αTi → βTi transformation and the transition temperature of the zirconia m → t transformation. The zirconia and composite samples were characterized by relative density about 98%, close to theoretical density. The slight growth of zirconia grains was observed.