New polymer electrolyte membrane for medium-temperature fuel cell applications based on cross-linked polyimide Matrimid and hydrophobic protic ionic liquid

New hydrophobic protic ionic liquid, 2-butylaminoimidazolinium bis(trifluoromethylsulfonyl)imide (BAIM-TFSI), has been synthesized. The ionic liquid showed good thermal stability to at least 350 °C. The conductivity of BAIM-TFSI determined by electrochemical impedance method was found to be 5.6 × 10^?2 S/cm at 140 °C. Homogeneous composite films based on commercial polyimide (PI) Matrimid and BAIM-TFSI containing 30–60 wt% of ionic liquid were prepared by casting from methylene chloride solutions. Thermogravimetric analysis data indicated an excellent thermal stability of PI/BAIM-TFSI composites and thermal degradation points in the temperature range 377 °C–397 °C. The addition of ionic liquid up to 50 wt% in PI films does not lead to any significant deterioration of the tensile strength of the polymer. The dynamic mechanical analysis results indicated both an increase of storage modulus E′ of PI/BAIM-TFSI composites at room temperature and a significant E′ decrease with temperature compared with the neat polymer. The cross-linking of the PI with polyetheramine Jeffamine D-400 allowed to prepare PI/Jeffamine/BAIM-TFSI (50%) membrane with E′ value of 300 MPa at 130 °C. The ionic conductivity of this cross-linked composite membrane reached the level of 10^?2 S/cm at 130 °C, suggesting, therefore, its potential use in medium-temperature fuel cells operating in water-free conditions.     

Copolymerization of methacrylic acid alkali metal salts and polyether-containing monomers in solid polymer electrolytes

Copolymerization of methacrylic acid alkali metal salts (MAAM; M = Li, Na, K, Rb or Cs) and oligo(oxyethylene) methacrylate (MEO) was carried out in bulk or in poly(oligo(oxyethylene) methacrylate) (PMEO) at 60°C. The copolymers of MAAM and MEO which were obtained by bulk polymerization showed a cation conductivity of around 1 × 10^?7 S/cm at room temperature. On the other hand, the copolymers obtained by radical polymerization in PMEO, showed a higher cation conductivity (10^?6–10^?5 S/cm). Furthermore, higher cation conductivity was observed for the copolymer systems containing alkali metal cations with a larger ion radius. This tendency was explained by the strength of the bond between alkali metal cation and ether oxygens. The degree of dissociation had little effect on this difference in the conductivity. The effective dissociation of methacrylic salts was enhanced in the copolymer compared to the homopolymer because of the suppression of the adjacent dissociative carboxylic acid groups. Arrhenius plots for ionic conductivity show the migration of ions along with the segmental motion of the polymer matrix.     

Synthesis and properties of polymeric analogs of ionic liquids

A number of methacrylate ionic monomers with different structures and mobilities of ionic centers were synthesized. The free-radical polymerization of these monomers in solution affords high-molecular-mass (M _sD = 0.5 to 2.5 × 10⁶) thermally stable (T _dec > 170°C) polyelectrolytes or cationic or anionic “polymeric ionic liquids.” The conductivities of polycation- and polyanion-derived coatings are (7.4 × 10^?10)?(7.6 × 10^?7) and (4.9 × 10^?10)-(1.6 × 10^?7) S/cm (25°C), respectively. As exemplified by poly(1-[3-(methacryloyloxy)propyl]-3-methylimidazolium bis[(trifluoromethanesulfonyl)imide]), the molecular mass and glasstransition temperature of the polymer affect the ionic conductivity of the film coating. The transition from linear polyelectrolytes to crosslinked systems based on ionic monomers and poly(ethylene glycol dimethacrylate) 750 leads to the formation of elastic films featuring satisfactory strength, reduced glass-transition temperatures (?8 to +15°C), and increased ionic conductivity (up to 3.2 × 10^?6 S/cm (25°C)).     

Polymers based on ionic monomers with side phosphonate groups

A number of new ionic vinyl monomers composed of 1-vinylimidazolium cation with diethoxy- and dihydroxyphosphoryl groups and various anions—Br^?, (CN)₂N^?, and (CF₃SO₂)₂N^?—are synthesized. The free-radical polymerization of the monomers in solutions of molecular and ionic solvents yields new polymer analogs of ionic liquids, and their molecular-mass characteristics, solubility, heat resistance, thermal stability, and electrical conductivity are estimated. It is shown that the incorporation of bulky phosphorylalkyl side substituents into the vinylimidazolium polycation causes a decrease in the glass-transition temperature and an increase in the ionic conductivity of polymer salts. The highest ionic conductivity (2.6 × 10^?5 S/cm at 25°C) is exhibited by the polymer with the (CN)₂N^? anion.     

The preparation and characterization of poly(urethane–peo-polar siloxane) complexes as polymer electrolytes

A series of novel poly(urethane-PEO-polar siloxane) copolymers and their complexes with LiClO₄ were prepared for assessment as polymer electrolytes and characterized by IR, GPC, and DSC, and their ionic conductivity and thermal stability were tested. The incorporation of polar siloxanes into U-PEO greatly increased conductivity. The highest conductivity was 2.6 × 10^?5 S cm^?1 at 25°C. The correlation between T_g, conductivity, and the ratio of siloxane to PEO as well as stability of the polymers are discussed. © 1995 John Wiley & Sons, Inc.     

Novel polymer electrolytes prepared by copolymerization of ionic liquid monomers

Ionic liquid monomer couples were prepared by the neutralization of 1‐vinylimidazole with vinylsulfonic acid or 3‐sulfopropyl acrylate. These ionic liquid monomer couples were viscous liquid at room temperature and showed low glass transition temperature (Tg) at ?83 °C and ?73 °C, respectively. These monomer couples were copolymerized to prepare ion conductive polymer matrix. Thus prepared ionic liquid copolymers had no carrier ions, and they showed very low ionic conductivity of below 10^?9 S cm^?1. Equimolar amount of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) to imidazolium salt unit was then added to generate carrier ions in the ionic liquid copolymers. Poly(vinylimidazolium‐co‐vinylsulfonate) containing equimolar LiTFSI showed the ionic conductivity of 4 × 10^?8 S cm^?1 at 30 °C. Advanced copolymer, poly(vinylimidazolium‐co‐3‐sulfopropyl acrylate) which has flexible spacer between the anionic charge and polymer main chain, showed the ionic conductivity of about 10^?6 S cm^?1 at 30 °C, which is 100 times higher than that of copolymer without spacer. Even an excess amount of LiTFSI was added, the ionic conductivity of the copolymer kept this conductivity. This tendency is completely different from the typical polyether systems. Copyright © 2002 John Wiley & Sons, Ltd.     

Synthesis,Characterization, and Conductivities of Poly(2-Vinylpyridine)-graft-Polyoxyethylene Using a Macromer Technique

Abstract

Poly(2-vinylpyridine) (P2-VP) with uniform polyoxyethylene (PEO) grafts was synthesized using a macromer technique. 2-Vinylpyridine was copolymerized with PEO macromer in solution by using azobisisobutyronitrile (AIBN) as the initiator. The effects of the amount of AIBN, the concentrations of 2-vinylpyridine and macromer, the number average molecular weight of macromer, and the charging ratio of macromer to 2-vinylpyridine in the copolymerization were studied. The copolymerization rate of the PEO macromer with 2-vinylpyridine was also investigated. The grafting efficiency reached about 56%. The crude graft copolymer was purified by extraction and precipitation, and it was characterized by IR, ¹H-NMR, and Bruss membrane osmometry. The PEO grafts were doped with LiClO₄ and showed ionic conductivity around 4.10 × 10^?6S°Cm^?1 at 25°C whereas the P2-VP main chains were complexed with TCNQ to obtain electronic conductivity around 5.50 × 10^?6 S°Cm^?1 at 25°C The mixed (ionic and electronic) conductivity of the doped copolymer could reach about 5.40 × 10^?5 S°Cm^?1 at 25°C and showed a synergistic effect.     

Polyvinyl chloride modification with sodium salt of 2-thiobenzimidazole

Polymer analogous reaction has been used to partially substitute chlorine atoms of polyvinyl chloride with 2-thiobenzimidazole fragments. ¹³C NMR and IR spectroscopy studies have shown that the vinylene units are present in the modified polymer. The copolymer product has been used to prepare the membrane with proton conductivity of 1 × 10^?2 to 0.04 S/cm at 25–195°C.     

Ionic conductivity of Li2MgSn3O8 ramsdellite

The ionic conductivity of polycrystalline pellets of Li₂MgSn₃O₈ with ramsdellite-type structure was measured by complex impedance technique. The conductivity is 1.2 × 10^?8 (Ω cm)^?1 at 300°C and 2.3 × 10^?4 (Ω cm)^?1 at 450°C. The results are discussed in relation to structural properties.     

Synthesis,structure, and properties of anhydrous organic-inorganic proton-exchange membranes based on sulfonated derivatives of octahedral oligosilsesquioxanes and α,ω-di(triethoxysilyl) oligo(oxyethylene urethane urea)

A method of obtaining new organic-inorganic nanostructured proton-exchange membranes operating via the anhydrous proton-conduction mechanism is proposed. An oligo(ethylene oxide) component serves as a proton-conducting phase in these membranes, and the sulfo derivatives of octahedral oligosilsesquioxanes of the acidic and acid-base types are used as proton-donor dopants. These compounds are synthesized via the reaction of octaaminopropyl oligosilsesquioxane with the cyclic anhydride of 2-sulfobenzoic acid at various ratios and contain sulfo groups solely or sulfo and amine groups in the organic frame. The combination of these compounds taken at concentrations of 20 and 50 wt % with α,ω-di(triethoxysilyl) oligo(oxyethylene urethane urea) and phenyltriethoxysilane via the sol-gel method gives rise to hybrid organic-inorganic proton-exchange membranes. The synthesized dopants are distributed in the oligoether component, but the nature of dopant distribution depends on their structure and concentration and has a significant impact on the structure of the resulting amorphous membranes (according to DSC, SAXS, and AFM data). The synthesized membranes are thermally stable up to 219°C. Their conductivity is provided by the segmental mobility of oligooxyethylene fragments (the Grotthuss mechanism) and, regardless of the dopant structure, is primarily determined by the number of charge carriers and the membrane structure. The temperature dependence of the conductivity is described by the Vogel-Fulcher-Tammann equation. The maximum values of the ionic conductivity are attained at 120°C under anhydrous conditions and dopant concentration of 50%: 1.03 × 10^?4 for ampholytic oligosilsesquioxane and 7.43 ×10^?5 S/cm for fully sulfonated oligosilsesquioxane as a dopant.     

Ionic IPNs as novel candidates for highly conductive solid polymer electrolytes

Five ionic imidazolium based monomers, namely 1‐vinyl‐3‐ethylimidazolium bis(trifluoromethylsulfonyl)imide (ILM1), 1‐vinyl‐3‐(diethoxyphosphinyl)‐propylimidazolium bis(trifluoromethylsulfonyl)imide (ILM2), 1‐[2‐(2‐methyl‐acryloyloxy)‐propyl]‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (ILM3), 1‐[2‐(2‐methyl‐acryloyloxy)‐undecyl]‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (ILM4), 1‐vinyl‐3‐ethylimidazolium dicyanamide (ILM5) were prepared and used for the synthesis of linear polymeric ionic liquids (PILs), crosslinked networks with polyethyleneglycol dimethacrylate (PEGDM) and interpenetrating polymer networks (IPNs) based on polybutadiene (PB). The ionic conductivities of IPNs prepared using an in situ strategy were found to depend on the ILM nature, T_g and the ratio of the other components. Novel ionic IPNs are characterized by increased flexibility, small swelling ability in ionic liquids (ILs) along with high conductivity and preservation of mechanical stability even in a swollen state. The maximum conductivity for a pure IPN was equal to 3.6 × 10^?5 S/cm at 20 °C while for IPN swollen in [1‐Me‐3‐Etim] (CN)₂N σ reached 8.5 × 10^?3 S/cm at 20 °C or 1.4 × 10^?2 S/cm at 50 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4245–4266, 2009     

Improving electrochemical performance of poly(vinyl butyral)-based electrolyte by reinforcement with network of ceramic nanofillers

This study has concerned the development of polymer composite electrolytes based on poly(vinyl butyral) (PVB) reinforced with calcinated Li/titania (CLT) for use as an electrolyte in electrochemical devices. The primary aim of this work was to verify our concept of applying CLT-based fillers in a form of nano-backbone to enhance the performance of a solid electrolyte system. To introduce the network of CLT into the PVB matrix, gelatin was used as a sacrificial polymer matrix for the implementation of in situ sol–gel reactions. The gelatin/Li/titania nanofiber films with various lithium perchlorate (LiClO₄) and titanium isopropoxide proportions were initially fabricated via electrospinning, and ionic conductivities of electrospun nanofibers were then examined at 25 °C. In this regard, the highest ionic conductivity of 2.55 × 10⁻⁶ S/cm was achieved when 10 wt% and 7.5 wt% loadings of LiClO₄ and titania precursor were used, respectively. The nanofiber film was then calcined at 400 °C to remove gelatin, and the obtained CLT film was then re-dispersed in solvated PVB-lithium bis(trifluoromethanesulfonyl)imide (PVB-LiTFSI) solution before casting to obtain reinforced composite solid electrolyte film. The reinforced composite PVB polymer electrolyte film shows high ionic conductivity of 2.22 × 10⁻⁴ S/cm with a wider electrochemical stability window in comparison to the one without nanofillers.

     

Studies on ionic liquid-based corn starch biopolymer electrolytes coupling with high ionic transport number

Biopolymer electrolytes containing corn starch, lithium hexafluorophosphate (LiPF₆) and ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate (BmImTf) were prepared by solution casting technique. The ionic conductivity was found to increase with increasing ionic liquid concentration. Upon doping with 80 wt% of BmImTf, the ionic conductivity increased by three orders of magnitude. The highest ionic conductivity of (3.21 ± 0.01) × 10^?4 S cm^?1 was achieved at ambient temperature. The complexation between corn starch, LiPF₆ and BmImTf was further proven in attenuated total reflectance-Fourier transform infrared findings. The highest conducting biopolymer electrolyte was stable up to 230 °C, as proven in thermogravimetric analysis.     

Ionic conductivity of Li7BiO6

The ionic conductivity of polycrystalline Li₇BiO₆ pellets has been measured by complex impedence method. The conductivity is 5.7 × 10^?3 (Ω cm)^?1 and 300°C and 3.8 × 10^?6 (Ω cm)^?1 at 100°C. Li₇BiO₆ is the best lithium conductor among the structurally related Li_nMO₆ compounds.     

Single-Li~+ conductivity in ionomeric network

Ionomeric networks(IN)with lithium sulfate and sait-solvating oligo(oxyethylene)chainwere synthesized on the purpose of improving the conductivity of single-Li~+-ionic conductors.Li~+-ionicconductivity depends considerably on the salt content of the INs although the apparent degree of cross-linking is fixed in a constant of 10 mol%.As salt content(Li/O value)equals 0.0467,conductivity ofthe IN containing neither small-molecular salt nor low molecular weight plasticizer reaches a maximumof 7×10~(-6) S/cm at 25℃.Temperature-conductivity relationship of the INs shows curved Arrheninsplots,suggesting that the ionic conduction is primarily influenced by segmental motion of the polymerhost.In addition,WLF(Williams-Landel-Ferry)equation is used to analyze the conductivity data,from which the related WLF parameters are determined.     

Low glass transition temperature polymer electrolyte prepared from ionic liquid grafted polyethylene oxide

In this contribution, we report a new type of poly (ionic liquids) prepared by imidazolium ionic liquids directly grafting onto polyethylene oxide backbone. Different molecular weights of poly (ionic liquids) are obtained with a low glass transition temperature up to ?14 °C. The materials as polymer electrolyte achieve a high conductivity around 10^?5 S cm^?1 at 30 °C and close to 10^?3 S cm^?1 at 90 °C. High viscosity up to 4000 Pa s at room temperature would minimize the electrolytes leaking in electrochemical devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2104–2110     

Design of alkaline metal ion conducting polymer electrolytes

Polysiloxanes with covalently attached oligo ethylene oxide and di-t-butylphenol ( I ), naphthol ( II ), and hexafluoropropanol ( III ) were synthesized. The crosslinked polymers with a hexamethylene spacer were also prepared. The ion conductivities of the Li, Na, and K salts were measured as a function of temperature. The highest conductivities for K and Na of I at 30°C were 5.5 × 10^?5 and 5.0 × 10^?5 S/cm, respectively, when the ratio of the ion to ethylene oxide unit was 0.014. On the other hand, Li conductivity was 8.0 × 10^?6 S/cm when the ratio between Li and ethylene oxide unit was 0.019. The maximum conductivities of Li ions of II and III were in the order of 10^?6 and 10^?7 S/cm at 30°C, respectively. When the polymers were crosslinked by a hexamethylene residue, the ion conductivities decreased while the degree of crosslinking increased. The temperature dependence of the cation conductivities of these systems could be described by the Williams-Landel-Ferry (WLF) and the Vogel-Tammann-Fulcher (VTF) equation. The results demonstrate that ion movement in these polymers is correlated with the polymer segmental motion. The order of ionic conductivity was K⁺ > Na⁺ ? Li⁺. This suggests that steric hindrance and π-electron delocalization of the anions attached to polymer backbone have a large effect on ion-pair separation and their ionic conductivities. Thermogravimetric analysis of the polymers indicated that the degradation temperature for I and II were about 100°C higher than for poly(siloxane-g-ethylene oxide). This is due to the antioxidant properties of sterically hindered phenols and naphthols. © 1993 John Wiley & Sons, Inc.     

Synthesis and ionic conductivity of hyperbranched poly(glycidol)

A novel hyperbranched poly(glycidol) (HPG) was prepared and characterized. The synthesized HPG was used as a substrate of a polymer electrolyte. The ionic conductivity of a blend of HPG, polyurethane (PU), and salt was studied. The ionic conductivity of HPG/PU/LiClO₄ was about 6.6 × 10^?6 S · cm^?1 at 20 °C and 6.3 × 10^?4 S · cm^?1 at 60 °C. The results indicated that HPG showed higher solubility for salt than linear polyether when both had the same [O]/[Li⁺] molar ratio. The main reason was that more cavities and a lower degree of chain entanglement in HPG resulted in a lower glass‐transition temperature and were beneficial for decreasing the aggregation of salt or enhancing the ionic conductivity. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2225–2230, 2001     

Conductivity studies of polymer electrolytes based on aliphatic polyesters

A series of aliphatic polyesters of sebacoyl chloride and poly(ethylene glycol) containing a different number of ethylene oxide groups was synthesized and characterized. These polyesters were complexed with lithium perchlorate to obtain a new class of polymer electrolyte. The relationships between the structure and properties of these polymer electrolytes were investigated. The main factor that affects the ionic conductivity in these systems was found to be the solvating capacity of the polyester for the lithium salt. These polymer electrolytes showed ionic conductivities up to 10^?5 ? 10^?4 S/cm at 25°C. The mechanical strength was improved by cross-linking, and the cross-linked polyester complexed with a LiCIO₄ salt showed an ionic conductivity of 2 × 10^?5 S/cm at room temperature. ⁷Li NMR spin-spin relaxation and dielectric relaxation studies were also carried out to investigate the local environments and dynamics of ions in the polymer electrolytes. © 1995 John Wiley & Sons, Inc.     

New solid polymer electrolytes based on polyester diacrylate for lithium power sources

New solid polymer electrolytes are developed for a lithium power source used at the temperatures up to 100°C. Polyester diacrylate (PEDA) based on oligohydroxyethylacrylate and its block copolymers with polyethylene glycol were offered for polymer matrix formation. The salt used was LiClO₄. The ionic conductivity of electrolytes was measured in the range of 20 to 100°C using the electrochemical impedance method. It is shown that the maximum conductivity in the whole temperature range is characteristic of the electrolyte based on the PEDA copolymer and polyethylene glycol condensation product (2.8 × 10^?6 S cm^?1 at 20°C, 1.8 × 10^?4 S cm^?1 at 95°C).