Polymer nanocomposites with “ultralow” refractive index

Nanocomposites of gelatine and gold were prepared by reduction of AuCl₄H in a gelatine solution, followed by a spin coating process and a brief washing. The thickness of the films thus obtained was typically 200–400 nm. The surface of the nanocomposites was investigated by scanning electron microscopy (SEM) and surface profilometry. The size of the gold particles is in the range of ca. 2–10 nm, as elucidated by transmission electron microscopy (TEM). Refractive indices were measured by ellipsometry at wavelengths of 632.8 and 1300 nm. The refractive index depends linearly on the volume fraction of gold, at least at 1300 nm. The lowest refractive indices measured are 1.008±0.060 at 1300 nm and 0.963±0.062 at 632.8 nm (limits are 95% confidence interval). These values are, to our best knowledge, the lowest reported for a polymer or polymer composite.     

Molecularly imprinted solid‐phase extraction method for the gas chromatographic analysis of organochlorine fungicides in ginseng

A highly selective molecularly imprinted solid‐phase extraction coupled with gas chromatography method was developed for the simultaneous isolation and determination of four organochlorine fungicides (pentachloronitrobenzene, pentachloroaniline, methylpentachlorophenyl sulfide, and hexachlorobenzene) in ginseng samples. A novel molecularly imprinted polymer with pentachloronitrobenzene as template was synthesized by precipitation polymerization employing butanone/n‐heptane (6.5:3.5, v/v) solution as porogen. The limit of detection of the method was 0.001 mg/kg, and the limit of quantification was 0.002 mg/kg. The different spiked levels of ginseng samples were 0.05, 0.5, 2.0 for pentachloronitrobenzene and pentachloroaniline, and 0.01, 0.1, 1.0 for methylpentachlorophenyl sulfide and hexachlorobenzene. The average recoveries of four organochlorine fungicides were 87.6–92.3% of pentachloronitrobenzene, 79.3–95.2% of pentachloroaniline, 80.3–90.4% of methylpentachlorophenyl sulfide, and 83.5–91.7% of hexachlorobenzene, respectively. This new method could be applied to direct determination of four organochlorine fungicides in ginseng samples.     

Structure of nanocomposites based on lead sulfide and poly-<Emphasis Type="Italic">p</Emphasis>-xylylene

Nanocomposites containing controlled (in the course of synthesis) concentrations of lead sulfide nanoparticles dispersed in the polymer matrix were prepared by the method of gas-phase polymerization on the surface of an active monomer, paracyclophane, which was codeposited with lead sulfide molecules. According to wide-angle X-ray diffraction measurements, the prepared nanocomposites contain lead sulfide clusters of 4 nm size, which are localized in the amorphous regions of poly-p-xylylene. Size distribution curves for lead sulfide particles as calculated on the basis of the Fourier analysis of crystallographic X-ray reflections and the volume distributions functions of particles as determined from small-angle X-ray scattering data are reported. A mechanism for the formation of lead sulfide nanoparticles in the poly-p-xylylene matrix is proposed on the basis of analysis of the X-ray scattering curves.     

Determination of phosphorus by electrothermal atomic absorption spectrometry with a phosphorus hollow-cathode lamp as light source

Graphite tubes are pre-heated with a 10% (w/v) zirconium solution, and a 1% (w/v) zirconium solution is injected prior to each phosphorus sample solution. The calibration graph is linear up to ca. 100 ng P, and the detection limit is 5 ng. Phosphorus in water-soluble organic and inorganic compounds can be determined directly by the proposed method, which is also suitable for the determination of phosphorus in NBS standard reference plant materials and in green tea leaves.     

Elimination of sulfide interference by sodium hypochlorite solution in the cold vapor atomic absorption spectrometric determination of mercury using tin(II) reduction in alkaline medium

An addition of sodium hypochlorite solution effectively eliminated the interference by sulfide in the cold vapor atomic absorption spectrometric determination of mercury using tin(II) reduction in alkaline medium. Mercury ranging from 0.01 to 0.5 μg could be determined within ±10% error in 100 mL of sample solution containing 10 mg of sulfide by the addition of 1 mL of 10.4%(w/v) sodium hypochlorite solution. The proposed method is rapid (5 min per determination) and has good reproducibility (3.0%).     

Determination of lead by hydride generation atomic absorption spectrometry : Part 1. A new medium for generating hydride

A new medium, used to generate lead hydride, was optimized as 0.3% (w/v) oxalic acid-2% (w/v) ammonium cerium (III) nitrate-8% (w/v) potassium tetrahydroborate-1% (w/v) sodium hydroxide solution; 950°C is used for atomization. The characteristic concentration (0.0044 absorbance) obtained under these conditions was 0.04 ng ml^?1. The application of this medium to soil and ferromagano-brass samples is illustrated.     

Rapid determination of lead and cadmium in biological fluids by electrothermal atomic absorption spectrometry using Zeeman correction

Procedures for the electrothermal atomic absorption spectrometric determination of lead and cadmium in urine, serum and blood are developed. For serum and blood, the samples are diluted by incorporating 0.015% (w/v) Triton X-100 and 0.1% (w/v) ammonium dihydrogenphosphate to the solutions, which are then introduced directly into the furnace. A solution containing 15% (w/v) hydrogen peroxide and 0.65% (w/v) nitric acid is also introduced into the atomizer by means of a separate injection. Zeeman-based correction is recommended. Both conventional and fast-heating programs are discussed. Calibration is carried out using the standard additions method. The reliability of the procedures is checked by analyzing three certified reference materials and by recovery studies.     

Parameters Influencing the Release of Tertiary Alcohols from the Surface of “Spherical” Dendrimers and “Linear” Stylomers by Neighbouring‐Group‐Assisted Hydrolysis of 2‐Carbamoylbenzoates

Size is not all! Investigation of the controlled release of tertiary alcohols from the surface of dendrimers and “stylomers” as polymer model systems (see scheme) showed that the polarity of the conjugates and structural modifications in close proximity to the release unit have a stronger influence on the rates of hydrolysis than the size (generation) or shape (linear or spherical) of the macromolecules.

     

Elimination of sulfide interference by sodium hypochlorite solution in the cold vapor atomic absorption spectrometric determination of mercury using tin(II) reduction in alkaline medium

An addition of sodium hypochlorite solution effectively eliminated the interference by sulfide in the cold vapor atomic absorption spectrometric determination of mercury using tin(II) reduction in alkaline medium. Mercury ranging from 0.01 to 0.5 μg could be determined within ±10% error in 100 mL of sample solution containing 10 mg of sulfide by the addition of 1 mL of 10.4%(w/v) sodium hypochlorite solution. The proposed method is rapid (5 min per determination) and has good reproducibility (3.0%). Received: 20 May 1998 / Revised: 7 July 1998 / Accepted: 10 July 1998     

Preparation of cadmium sulfide nanoparticles in self-reproducing reversed micelles

Octyl octanoate (O-OL) underwent hydrolysis in sodium octanoate (NaOA) reversed micelles in 85:15 = isooctane:octanol (OL) (v/v), containing w = [H2O]/[NaOA] = 40. The products of the hydrolysis, octanoic acid (OA) and octanol (OL), lead to the formation of additional (albeit smaller) reversed micelles; hence the process is considered to be self-reproducing. Self-reproduction was found to be catalyzed by lithium hydroxide, solubilized in the water pools, as well as by hydrogen sulfide, added to the solution of the reversed micelles. Addition of hydrogen sulfide to cadmium perchlorate containing self-reproducing reversed micelles resulted in the formation of cadmium sulfide (CdS) nanoparticles. Diameters of the CdS containing nanoparticles could be altered from 5.4 to 1.8 nm by changing the [Cd2+]/[H2S] ratios from 0.25 to 10. The CdS nanoparticles formed were capped by mercaptopropionic acid, isolated as solids, and could be repeatedly redispersed in water without changing their sizes. Additional CdS nanoparticles were generated in the supernatants removed from the precipitated capped CdS nanoparticles.     

The polymerization of acrylonitrile in miniemulsions: “Crumpled latex particles” or polymer nanocrystals

Stable dispersions of polyacrylonitrile (PAN) nanoparticles in the size range between 100 nm < d < 180 nm were made by polymerization in miniemulsion and characterized by dynamic light scattering, transmission electron microscopy (TEM), and wide angle X‐ray scattering (WAXS). Due to the insolubility of the polymer in its monomer, such particles are not accessible by classical emulsion polymerization. The pure PAN particles are composed of ca. 10 nm large polymer nanocrystals, i. e., the formed polymer precipitates and crystallizes direct after formation. As a consequence, the final latexes do not adopt spherical shape, but show a well defined, narrowly distributed boulder‐like phenotype which is called “crumpled latexes”. Copolymerization with styrene results in a continuous transition between the crumpled and a smooth spherical morphology, which is again related to a decreased degree of crystallinity.     

DNA sequencing by capillary electrophoresis using mixtures of polyacrylamide and poly(N,N-dimethylacrylamide)

The possibility of using polymer mixtures with different chemical compositions as a DNA sequencing matrix by capillary electrophoresis (CE) has been exploited. Polyacrylamide (PAM, 2.5%, w/v) having a molecular mass of 2.2 x 10(6) has been mixed with poly(N,N-dimethylacrylamide) (PDMA) having molecular masses of 8000, 470000 and 2.1 x 10(6) at concentrations of 0.2, 0.5 and 1% (w/v). Unlike polymer mixtures of the same polymer with different molecular masses, the use of polymer mixtures with different chemical compositions encounters an incompatibility problem. It was found that the incompatibility increased with increasing PDMA molecular mass and PDMA concentration, which resulted in decreased efficiency in DNA sequencing. Also, the incompatibility had a more pronounced effect on the efficiency as the base number was increased. However, by choosing a low-molecular-mass PDMA of 8000 and a low concentration of 0.2% (w/v), the incompatibility of PAM and PDMA has been alleviated. At the same time, the advantage of using polymer mixtures revealed a higher efficiency for such a polymer mixture when compared with PAM. The mixture also endowed the separation medium with a dynamic coating ability. An efficiency of over 10 x 10(6) theoretical plates per meter has been achieved by using the bare capillaries without the additional chemical coating step.     

Fast determination of lead and copper in dairy products by graphite furnace atomic absorption spectrometry

A rapid and direct procedure for determining lead and copper in dairy products by electrothermal atomic absorption spectrometry (ETAAS) is described. Samples are slurried in a medium containing 50% v/v hydrogen peroxide, 1% v/v nitric acid, 0.5% w/v dihydrogen phosphate, and 20% v/v ethanol and directly injected into the furnace with no previous mineralization. Calibration is performed with aqueous standards. Limits of determination were 0.4 and 2.4 ng/mL for copper and lead, respectively. The reliability of the procedure was checked by comparison with the acid mineralization procedure and by analyzing 3 certified reference milk samples.     

Formulation and Optimization of Alkaline Extracted Ispaghula Husk Microscopic Reservoirs of Isoniazid by Box-Behnken Statistical Design

The main objective of the present work was to formulate and optimize a microparticulate sustained release drug delivery system of isoniazid by using a novel, alkaline extracted ispaghula husk as a polymer. Isoniazid microspheres of alkaline extracted ispaghula husk were prepared by emulsification internal ionic gelation method. Results of preliminary trials indicated that the polymer concentration, cross-linking agent and stirring speed had a noticeable effect on size and surface morphology. A four-factor three-level Box-Behnken design was employed to study the effect of independent variables on dependent variables. The particle size and entrapment efficiency varied from 30.75 to 61.78 µm and 62.27% to 85.80% respectively, depending on the polymer concentration, concentration of cross-linker and stirring speed. Optimized microspheres batch based on point prediction tool of design software exhibited 83.43% drug entrapment and 51.53 µm particle size with 97.80% and 96.37% validity, respectively at the following conditions: sodium alginate (3.55% w/v), alkaline extracted ispaghula husk (3.60% w/v), cross-linker concentration (7.82% w/v), and stirring speed (1200 rpm). The optimized formulation showed controlled drug release for more than 12 hours. The drug release followed Higuchi kinetics via a non-Fickian diffusion.     

In Situ Hetero End‐Functionalized Polythiophene and Subsequent “Click” Chemistry With DNA

It is demonstrated that bifunctionalized polythiophenes involving thiol and azide end‐functional groups can be synthesized by chain‐growth Suzuki‐Miyaura type polymerization. The bifunctionalized polythiophenes are successfully characterized by 1H NMR, gel permeation chromatography (GPC), and matrix‐assisted laser desorption ionization time‐of‐flight (MALDI‐TOF). Furthermore, the azide end‐group reacts with DNA via “click chemistry” to form a polythiophene/DNA hybrid structure, which is characterized by ESI‐MS. The described synthetic approaches will lead to the synthesis of novel multi‐block copolymers as well as biomolecule‐based conjugated polymer structures.     

Side‐Chain Modification and “Grafting Onto” via Olefin Cross‐Metathesis

Olefin cross‐metathesis is introduced as a versatile polymer side‐chain modification technique. The reaction of a poly(2‐oxazoline) featuring terminal double bonds in the side chains with a variety of functional acrylates has been successfully performed in the presence of Hoveyda–Grubbs second‐generation catalyst. Self‐metathesis, which would lead to polymer–polymer coupling, can be avoided by using an excess of the cross‐metathesis partner and a catalyst loading of 5 mol%. The results suggest that bulky acrylates reduce chain–chain coupling due to self‐metathesis. Moreover, different functional groups such as alkyl chains, hydroxyl, and allyl acetate groups, as well as an oligomeric poly(ethylene glycol) and a perfluorinated alkyl chain have been grafted with quantitative conversions.     

Formation of concentration gradient and its application to DNA capillary electrophoresis

A new method to introduce the concentration gradient into the capillary has been developed and its application to DNA capillary electrophoresis is presented. The concentration gradient produced by mixing 5% w/v polyacrylamide-co-poly(N-dimethylacrylamide) (PAM-co-PDMA) solution and 1 x Tris/N-tris(hydroxymethyl)methyl-3-amino-propanesulfonic acid/EDTA (TT) + 5 M urea buffer was successfully achieved by using two programmable syringe pumps with strict control of dead volume, flow rate, and pressure balance. This method has the advantages of high stability, reproducibility, and versatility. The column with concentration gradient greatly improved the resolution, especially for the large DNA fragments, due to a decrease in band width broadening with time. A column containing 2-4% w/v gradient in four steps had a longer read length, shorter separation time and better resolution (after 380 base) than that of 4% w/v single concentration polymer solution. The number of steps in the gradient had almost no effect on the performance. The change in the average concentration by relocating the position of the same step gradient, i.e., a combination of different low concentration to high concentration polymer solution ratios, resulted in a different migration time, read length and resolution.     

Analysis of isoquinoline alkaloids using chitosan‐assisted liquid–solid extraction followed by microemulsion liquid chromatography employing a sub‐2‐micron particle stationary phase

A simple, efficient, and green chitosan‐assisted liquid–solid extraction method was developed for the sample preparation of isoquinoline derivative alkaloids followed by microemulsion LC. The optimized mobile phase consisted of 0.8% w/v of ethyl acetate, 1.0% w/v of SDS, 8.0% w/v of n‐butanol, 0.1% v/v acetic acid, and 10% v/v ACN. Compared to pharmacopoeia method and organic solvent extraction, this new approach avoided the use of volatile organic solvents, replacing them with relatively small amounts of chitosan. Under the optimum conditions, good linearity (r² > 0.9980) for all calibration curves and low detection limits between 0.05 and 0.10 μg/mL were achieved. The presented procedure was successfully applied to determine alkaloids in Rhizoma coptidis with satisfactory recoveries (81.3–106.4%).     

Sulfonated acrylamide copolymers as pseudo-stationary phases in electrokinetic chromatography

Sulfonated copolymers were synthesized, characterized and used as separation media in electrokinetic chromatography. The polymers used were synthesized from AMPS (2-acrylamido-2-methyl-1-propanesulfonic acid) and LMAm (lauryl methacrylamide) in different mole ratios (from 100:0 to 60:40). Electrophoretic mobilities and methylene selectivities were calculated, which showed the expected correlation with the monomer ratios. The chemical selectivities for the separation of nine solutes by the copolymers were compared with that of sodium lauryl sulfate micelles, showing significant differences. No significant difference in chemical selectivities was observed for copolymers with different monomer ratios. No significant change of hydrophobic microdomain of copolymers was found in background buffers with different ionic strength values, based on the investigation of the retention factors, methylene selectivities and polymer effective mobilities. No change of hydrophobic microdomain of the copolymer solutions was found at copolymer concentrations from 0.17 to 3% (w/v), however, plots of k' versus polymer concentration suggested a different copolymer phase at lower concentrations (from 0 to 0.1%, w/v) from that at higher concentrations (from 0.17 to 3%, w/v). The copolymer with AMPS-LMAm (80:20) could be chosen as optimum copolymer as far as the methylene selectivity, peak symmetry and polymer mobility were concerned.     

Synthesis and characterization of “umbrella” shaped polymers

A new strategy has been developed to prepare umbrella polymer, i.e. star polymers with one heteroarm. The synthesis uses living anionic polymerization to prepare a short segment of 1,2-polybutadiene at the end of a linear polystyrene. The vinyl groups of 1,2-polybutadiene are hydrosilylated with dichloro(methyl)silane. The umbrella polymer is then formed by nucleophilic displacement of the silicon-chlorine with 1,4-polybutadienyllithium. An umbrella polymer with poly(2-vinylpyridine) arms is prepared in the same way after hydrosilylation with chlorodimethylsilane. The umbrella polymers are characterized by light scattering, size-exclusion chromatography (SEC), ultraviolet/visible spectroscopy (UV/vis), nuclear magnetic resonance (NMR) and intrinsic viscosity.