Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

The Electrochemical Behavior of p-Aminophenol at a ω-Mercaptopropionic Acid Self-Assembled Gold Electrode

A -mercaptopropionic acid (MPA) self-assembled monolayer modified electrode (MPA/SAM/Au) on a gold electrode has been fabricated. The characterization of the MPA/SAM/Au was investigated using attenuated total reflection-fourier transform infrared (ATR-FTIR) and A.C. impedance. The electrochemical behaviors of p-aminophenol (p-AP) were studied at the MPA/SAM/Au by cyclic voltammetry and semi-derivative voltammetry (SDV) in BR buffer solution. The modified electrode shows excellent electrocatalytic activity for the redox of p-AP and accelerates the electron transfer rate. The diffusion coefficient (D) is 4.55×10^–6cm²s^–1. The oxidative peak current increases linearly with the concentration of p-AP in the range of 4.0×10^–88×10^–6molL^–1 and 1.0×10^–52×10^–4molL^–1 by square wave voltammetry response, respectively. The detection limit (three times the signal blank/slope) is up to 1.2×10^–8molL^–1. The modified electrode is able to eliminate the interference of p-benzenediol, o-benzenediol and o-AP at a 40-, 90- or 70-fold concentration of p-AP, and it has been satisfactorily used for the determination of the real sample.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Determination of Attogram Quantities of Silver via Quenching of the Solid Substrate Room-Temperature Phosphorescence of Rhodamine B Based on the Catalysis of its Oxidation by Potassium Persulfate

A new method of SS-RTP for the determination of trace silver has been established. This method is based on the fact that Ag⁺, when activated by ,-bipyridyl (bipy) in a media of HAc–NaAc (pH=4.9), can catalyze the reaction of Rhodamine B (RhoB) oxidized by K₂S₂O₈, thus causing the Solid Substrate Room-Temperature Phosphorescence (SS-RTP) of RhoB to be quenched. The activating efficiency of bipy is 6.7 times higher than that of o-phenanthroline (phen). The reduction of the phosphorescence intensity (I_p) of RhoB is directly proportional to the concentration of Ag⁺ ions in the range of 1.6016.0agspot^–1 (0.40µLspot^–1). The regression equation of the working curve can be expressed as I_p=18.78+5.100m_Ag+ (agspot^–1) (r=0.9994, n=6), the detection limit is 0.28agspot^–1. This rapid, accurate and sensitive method has been successfully applied to the determination of trace silver in tea and human hair samples, and the results agree well with the Atomic Absorption Spectroscopy (AAS) method. The mechanism of the catalyzing reaction is also discussed.     

Fluorimetric Flow-Through Sensing of Quinine and Quinidine

We describe a single continuous-flow method for the determination of Quinine (QN) and Quinidine (QD) based on the enhancement of their native fluorescence by on-line transitory retention on a solid support placed in a flow cell. KCl solution was used as carrier/self-eluting solution. The active solid surface is regenerated by the carrier itself which also acts as eluting solution, thus making the microsensing zone reusable for subsequent measurements.In the range of 40 to 1260µL, the response of the sensor (_exc/_em=250/450nm) was directly proportional to the sample volume injected. The sensor was calibrated for three injection volumes: 40, 600 and 1000µL, responding linearly in the range of 40–800, 2–40 and 0.4–20µgL^–1 of QN and 20–600, 5–40 and 0.9–20µgL^–1 of QD with detection limits of 2.2, 0.2 and 0.1µgL^–1 (QN) and 3.9, 0.4 and 0.2µgL^–1 (QD), respectively. The relative standard deviation for ten independent determinations is 1.0% (QN) and 3.9% (QD). The sampling frequency ranges between 40 and 22h^–1 depending on the sample volume injected. This sensor was satisfactorily applied to the determination of QN in soft drink samples and a shampoo, and to the determination of QD in pharmaceutical preparations with equally satisfactory results.     

Direct Microspectrophotometric Determination of Bismuth in Silver with Semi-Xylenol Orange

75–300ng of bismuth in a sample mass of 20mg of silver can be determined spectrophotometrically in a nitric acid medium (0.18molL^–1) with Semi-Xylenol Orange as chromogenic agent. Its selectivity is realized by using less toxic reagents in very small amounts to mask some of the interfering impurity cationic species while the matrix effect is negligible. The conditional formation constant of the colored chelate formed was found to be lgK_f=3.1. It exhibits a maximum at 540nm with a molar absorptivity of 4.2×10⁴Lmo1^–1cm^–1. The linear regression equation for this determination is A=0.022+0.0018C, where C stands for the concentration of Bi (ng per 0.5mL) with a correlation coefficient of 0.9873. The RSD at the level of 200ng of Bi (n=10) was found to be 5%.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Determination of Na,K, Rb and Cs Distribution in Human Brain Using Neutron Activation Analysis

This study aims to investigate the distribution of Na, K, Rb and Cs in human brains (5 individuals, 12 brain parts, mean age: 75 years). Distribution of the trace metals between lipid fraction and brain tissue was investigated in solvent extraction experiments. Determinations were carried out by instrumental neutron activation analysis. The present results show a rather non-homogeneous distribution for Na and a relatively uniform distribution for K, Rb and Cs. The mean concentrations found are 7440µgNag^–1 dry weight, 12800µgKg^–1, 14µgRbg^–1 and 50ngCsg^–1. A highly significant positive correlation was found between Rb and Cs. Solvent extraction experiments showed that 19% of Rb and 26% of Cs of the total content is located in lipid fraction.     

Mixed ligand complexes involving aminoacid dithiocarbamates,substituted phosphines and nickel(II)

Mixed ligand complexes involving four aminoacid dithiocarbamates (RRdtc=glydtc^– (R=H; R=H), methdtc^– (R=H; R=C₃H₇S), sardtc^– (R=Me; R=H), trydtc^– (R=H; R=C₉H₈N), substituted phosphines [PPh₃, Ph₂PCH₂CH₂PPh₂(dppe)] and nickel(II) are reported. All are diamagnetic. Thermal analyses of the complexes are in keeping with the proposed formulae. Thermal decomposition of the dithiocarbamate moiety proceeds through the formation of Ni(SCN)₂. PPh₃ and dppe are lost in the initial decomposition stages.     

Electrochemical Determination of Cinnamtannin B1 with a Pyrolytic Graphite Electrode

Cinnamtannin B1 (trimeric proanthocyanidin), which is identified and isolated from the effective fraction of the root of Lindera aggregata (Sims) Kosterm, is one kind of condensed tannin used as an effective antipyrotic and antitumor agent. Its electrochemical response can be obtained at a pyrolytic graphite electrode. Consequently, an easily performed and sensitive method for the determination of cinnamtannin B1 is developed. The detection limit is estimated to be 1.0×10^–7M with the linear determination range of 2.0×10^–7M to 1.8×10^–6M. Five replicate analyses of 1.0×10^–6M cinnamtannin B1 yields an RSD value of 2.1%. Since the working electrode does not need to be modified with any other species, it is very stable, repeatable and easily treated, and this method therefore potentially useful in real sample analysis.     

Determination of Lead Using a New Chromogenic Reagent 2-(2-Sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic Acid

A novel chromogenic reagent, 2-(2-sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid 1, was prepared by diazo coupling of 4-acetylaniline-2-sulfonic acid and 2,4,6-trichloroaniline to chromotropic acid through –N=N– groups. Based on this reagent, a simple, sensitive and selective spectrophotometric method was developed for the determination of lead. In 0.20M phosphoric acid medium, lead reacts with 1 to form a 1:2 blue complex with an absorption maximum of 654nm. Beers law is obeyed in the range of 0–0.6mgL^–1 of lead. The apparent molar absorptivity is 1.25×10⁵Lmol^–1cm^–1. The detection limit and quantification limit were found to be 0.63µgL^–1 and 2.1µgL^–1, respectively. The relative standard deviation for eleven replicate measurements was of 2.6%. The interference of foreign ions was also investigated. All the other foreign ions studied did not interfere with lead determination except for Ca(II) and Ba(II). The interference caused by Ca(II) and Ba(II) can be eliminated by prior extraction of lead with potassium iodide-methylisobutylketone (KI-MIBK). The proposed method was applied to the determination of lead in certified samples with satisfactory results.     

Determination of Proteins at Nanogram Levels Using the Resonance Light Scattering Technique with a Novel PVAK Nanoparticle

A novel functionalized polyvinyl alcohol keto-derivative nanoparticle (PVAK) has been prepared in a one-step method using oxidation and degradation under ultrasonic irradiation. The nanoparticle is water-soluble, chemically stable, non-toxic and biocompatible. The surface of the nanoparticle is covered with abundant hydroxyl, carbonyl and carboxyl. At pH 3.0, the interactions of PVAK with different proteins can result in obviously enhanced RLS signals at 380nm. Under optimal conditions, the calibration graphs are linear over the range of 0.024.0µgmL^–1 for human serum albumin (HSA), 0.023.5µgmL^–1 for bovine serum albumin (BSA), and 0.053.5µgmL^–1 for human -globulin (-G), respectively. Detection limits were 6.4ngmL^–1 for HSA, 9.2ngmL^–1 for BSA, and 12.5ngmL^–1 for -G, respectively. The method was employed for the determination of total proteins in human serum with satisfactory results.     

Non-Aqueous Capillary Electrophoresis with Indirect Photometric Detection for Direct Analysis of Pb2+, Zn2+ and Cd2+ Ions

A new approach, based on non-aqueous capillary electrophoresis separation and indirect photometric detection, was established for the determination of the transition metal ions Pb²⁺, Zn²⁺ and Cd²⁺. Under optimized conditions, the method produced baseline separation of these three metal ions. The linear range and detection limits were 1050µM, 1.9µM for Cd²⁺; 1050µM, 2.1µM for Zn²⁺; and 20100µM, 3.8µM for Pb²⁺, respectively.     

Adsorptive Catalytic Voltammetry of Physcion in the Presence of Dissolved Oxygen at a Carbon Paste Electrode

A novel electroanalytical method for the determination of physcion is described for the first time. Physcion yields an adsorption catalytic voltammetric peak at –0.74V (vs. SCE) in 0.4molL^–1 NH₄Cl–NH₃·H₂O buffer solution (pH 10.5) at a carbon paste electrode (CPE). The experimental results indicated that physcion is efficiently accumulated at a CPE by adsorption. In the subsequent potential scan, physcion was reduced to a homologous anthrahydroquinone compound. The compound was then immediately oxidized to physcion by the dissolved oxygen in the solution, and then physcion was again reduced at the CPE. As a result, a cyclic catalytic reaction was established. The second-order derivative peak current is proportional to the physcion concentration in the ranges of 2.0×10^–104.0×10^–9molL^–1 (accumulation 90s) and 4.0×10^–92.0×10^–8molL^–1 (accumulation 60s). The limit of detection is 8×10^–11molL^–1 (S/N=3) for a 120s accumulation time. The method was applied to the direct determination of physcion in the medicinal plant polygonum multiflorum Thumb with satisfactory results.     

Kinetics of formation,dissociation and equilibrium constants of pentacyanoaquoruthenate(II) with heterocycles

The kinetics of formation and dissociation reactions of [Ru(CN)₅L]^3– with a series of heterocyclic ligands were studied in aqueous media. In this presence of an excess of heterocycle, the observed second order rate constants were calculated from the k_obs versus [ligand] plot at =0.100m NaClO₄. Activation parameters for the formation reactions (H=28±7kJmol^–1 and S=140±35JK^–1mol^–1) are comparable for all systems, indicating a common mechanism. The kinetics of exchange of coordinated heterocycles for 1,3,5-triazine yielded a rate saturation typical of a limiting dissociative mechanism. Activation parameters of the limiting first order specific rate of dissociation reactions were H=85±7kJmol^–1 and S=18±4JK^–1mol^–1. Equilibrium constants were calculated from the second order rates of formation and pseudo-first order rates of dissociation reaction.     

Simple and Sensitive Assay for Nucleic Acids Using their Quenching Effect on the Chemiluminescence Reaction Between Luminol and Hydrogen Peroxide with Manganese-Tetrasulfonatophthalocyanine as a New Catalyst

The manganese-tetrasulfonatophthalo-cyanine (MnTSPc) catalyzed luminol-hydrogen peroxide chemiluminescence (CL) system can be quenched in the presence of nucleic acids. A new and highly sensitive CL quenching method for determining nucleic acids in aqueous solutions has been developed. Under optimum conditions, linear relationships were found between the quenched intensity of CL and the concentration of nucleic acids in the range 0.10–2.0µgmL^–1 for calf thymus DNA and 0–1.6µgmL^–1 for fish sperm DNA. The limits of detection were 14.8ngmL^–1 for calf thymus DNA and 21.7ngmL^–1 for fish sperm DNA. The relative standard deviation (RSD) of nine replicate measurements is 1.4% for 1.0µgmL^–1 calf thymus DNA. The method was applied to the analysis of nucleic acids in synthetic samples and the results are satisfactory.Received December 2, 2002; accepted June 2, 2003 published online September 1, 2003