Silyl enol ethers as monomer. III. Radical polymerization and copolymerizations of 2-trimethylsilyloxy-1,3-butadiene and desilylation of the resulting polymers

2-Trimethylsilyloxy-1,3-butadiene (TMSBD), the silyl enol ether of methyl vinyl ketone, was homopolymerized with a radical initiator to afford polymers with a molecular weight of ca. 10⁴. Radical copolymerizations of TMSBD with styrene (ST) and acrylonitrile (AN) in bulk or dioxane at 60°C gave the following monomer reactivity ratios: r₁ = 0.64 and r₂ = 1.20 for the ST (M₁)–TMSBD (M₂) system and r₁ = 0.036 and r₂ = 0.065 for the AN (M₁)–TMSBD (M₂) system. The Q and e values of TMSBD determined from the reactivity ratios for the former copolymerization system were 2.34 and ?1.31, respectively. The resulting polymer and copolymers were readily desilylated with hydrochloric acid or tetrabutylammonium fluoride as catalyst to yield analogous polymers having carbonyl groups in the polymer chains.     

Copolymerization of trifluoropropene with itaconic acid and ethylvinylether by using gamma rays

Copolymerization of trifluoropropene (TFP) with itaconic acid (IA) and ethylvinylether (EVE) have been carried out by using gamma rays from a ⁶⁰Co source. Copolymers of TFP-IA and TFP-EVE were white powder and white grease, respectively. The copolymerization rate of TFP-IA system is proportional to 0.64 power of dose rate and that of TFP-EVE system is proportional to 1.0 power of dose rate. The apparent activation energy for TFP-IA system is 4.3 kcal/mol and it is 10 kcal/mol for TFP-EVE system. The copolymerizations of both TFP-IA and TFP-EVE are inhibited remarkably by a radical scavenger, PBQ. The reactivity ratios for those systems were determined roughly to be r_TFP = 0.55, r_IA = 13 and r_TFP = 0.30, r_EVE = 0.20.     

Water-Soluble Copolymers. XLI. Copolymers of Acrylamide and Sodium 3-Acrylamido-3-methylbutanoate

Copolymers of acrylamide (AM, M ₁) with sodium 3-acrylamido-3-methylbutanoate (NaAMB, M ₂) synthesized in 1 M NaCl (the ABAM2 series) are compared to those synthesized in deionized water (the ABAM1 series). At fixed feed ratios, higher incorporation rates were found for NaAMB with increasing ionic strength of the polymerization solvent. Reactivity ratios calculated by the methods of Kelen-Tüdös changed from r ₁ = 1.23 and r ₂ = 0.50 in deionized water to r ₁ = 1.00 and r ₂ = 0.64 in 1 M NaCl. This change is in accord with a decrease in electrostatic repulsion between the macroradical and unreacted NaAMB. Dilute solution properties, examined as a function of composition and added electrolytes, indicate differences in microstructure for the ABAM1 and ABAM2 copolymers.     

Monomer reactivity ratio and Q–e values for copolymerization of hydroxyalkyl acrylates and 2-(1-aziridinyl)ethyl methacrylate with styrene

Copolymers of 2-hydroxyethyl acrylate, hydroxypropyl acrylate, and 2(1-aziridinyl)-ethyl methacrylate (M₂) with styrene (M₁) were prepared in benzene solution at 60°C. Benzoyl peroxide, 0.1–0.2 mole-%, was used as initiator. Copolymer samples with the molar concentrations of M₂ feed ranging from 0.10 to 0.85 were used to determine the reactivity ratios. Elemental analysis and nuclear magnetic resonance spectroscopy (NMR) were used to determine copolymer compositions. There was a solubility problem when the latter technique was applied. When samples which were completely soluble were analyzed, the results obtained from NMR and elemental analysis were in excellent agreement. The monomer reactivity ratios and the corresponding parameters for the copolymerization of (M₁) with 2-hydroxyethyl acrylate are: r₁ = 0.38 ± 0.02, r₂ = 0.34 ± 0.03; Q₂ = 0.85, e₂ = 0.64; with hydroxypropyl acrylate are: r₁ = 0.45 ± 0.03, r₂ = 0.36 ± 0.03; Q₂ = 0.75, e₂ = 0.56; with 2(1-aziridinyl)ethyl methacrylate are: r₁ = 0.53 ± 0.02, r₂ = 0.63 ± 0.04; Q₂ = 0.82, e₂ = 0.25.     

Copolymerization of new pyrazolone-containing monomers with certain vinyl comonomers

The polymerization ability of two new pyrazolone-containing monomers—3-methyl-1-phenyl-4-crotonoyl-pyrazolone-5 ( Cr ) and 3-methyl-1-phenyl-4-(3′-phenyl-acryloyl) pyrazolone-5 ( Cy )—was investigated. The monomers were obtained by acylation of 3-methyl-1-phenyl-pyrazolone-5 with crotonyl chloride or cinnamoyl chloride, respectively. It was established that the two monomers do not homopolymerize either under the action of ionic and radical initiators nor with γ-rays (doses between 2 and 10 MRad). In contrast to this, the two monomers copolymerize with other vinyl comonomers. Copolymers of Cr and Cy with methacrylic acid (MAA), methyl methacrylate (MMA), and Styrene (St) were synthesized by radical copolymerization. The molecular weights of the polymer products obtained were in the 10,000–65,000 range. It was established that the molecular weight characteristics of the copolymers were affected by the concentration of the pyrazolone-containing monomer and by the chemical nature of the solvent used. The copolymerization of Cr and Cy with MAA was investigated in detail in order to evaluate the relative activity of the new monomers during copolymerization. The reactivity ratios (r) were calculated by three different methods with good agreement. The values obtained for the monomer pairs are: r_MAA = 0.61 ± 0.01, r_Cr = 0.04 ± 0.01; r_MAA = 0.64 ± 0.05, r_Cy = 0.02 ± 0.02. The Q/e values for Cr and Cy were determined using the reactivity ratios of both monomers.     

Copolymerization of vinylsilanes with styrene

New vinylsilanes (M₂), i. e. phenylvinylsilane (I), allylmethylsilane (II), allylphenylsilane (III), and p-vinylphenylmethylsilane (IV), were prepared and copolymerized with styrene (M₁). The monomer reactivity ratios were r₁ = 5.7 and r₂ = 0, r₁ = 36 and r₂ = 0, r₁ = 29 and r₂ = 0₁, and r₁ = 0.91 and r₂ = 1.1, respectively. From the results of infrared and NMR spectra it was indicated that the vinylsilanes participated in copolymerization in the form of a vinyl type of polymerization and not in the form of a hydrogen-transfer type of polymerization. The reaction of copolymer with alcohols and methyl methacrylate and appropriate catalysts was investigated.     

Vinylhydroquinone. III. Copolymerization of vinylhydroquinone and vinyl monomers by tri-n-butylborane

The copolymerization of vinylhydroquinone (VHQ) and vinyl monomers, e.g., methyl methacrylate (MMA), 4-vinyl-pyridine (4VP), acrylamide (AA), and vinyl acetate (VAc), by tri-n-butylborane (TBB) was investigated in cyclohexanone at 30°C under nitrogen. VHQ is assumed to copolymerize with MMA, 4VP, and AA by vinyl polymerization. The following monomer reactivity ratios were obtained (VHQ = M₂): for MMA/VHQ/TBB, r₁ = 0.62, r₂ = 0.17; for 4VP/VHQ/TBB, r₁ = 0.57, r₂ = 0.05; for AA/VHQ/TBB, r₁ = 0.35, r₂ = 0.08. The Q and e values of VHQ were estimated on the basis of these reactivity ratios as Q = 1.4 and e = ?;1.1, which are similar to those of styrene. This suggests that VHQ behaves like styrene rather than as an inhibitor in the TBB-initiated copolymerization. No homopolymerization was observed either under nitrogen or in the presence of oxygen. The reaction mechanism is discussed.     

Studies of the polymerization of diallyl compounds. XXVII. Copolymerization of diallyl tartrate with several vinyl monomers

The radical copolymerization of diallyl tartrate (DATa) (M₁) with diallyl succinate (DASu), diallyl phthalate (DAP), allyl benzoate (ABz), vinyl acetate (VAc), or styrene (St) was investigated in order to disclose in more detail the characteristic hydroxyl group's effect observed in the homopolymerization of DATa. In the copolymerization with DASu or DAP as a typical diallyldicarboxylate, the dependence of the rate of copolymerization on monomer composition was different for different copolymerization systems and unusual values larger than unity for the product of monomer reactivity ratios, r₁r₂, were obtained. In the copolymerization with ABz or VAc (M₂), the r₁ and r₂ values were estimated to be 1.50 and 0.64 for the DATa/ABz system and 0.76 and 2.34 for the DATa/VAc system, respectively; the product r₁r₂ for the latter copolymerization system was found again to be larger than unity. In the copolymerization with St, the largest effect due to DATa monomer of high polarity was observed. Solvent effects were tentatively examined to improve the copolymerizability of DATa. These results are discussed in terms of hydrogen-bonding ability of DATa.     

Monomer reactivity ratios for the copolymerization of styrene with 1,2,4-trivinyl and p-divinylbenzenes

The copolymerization kinetics of 1,2,4-trivinylbenzene (TVB) with styrene do not clearly resemble those of o-, m-, or p-divinylbenzene (DVB), structural elements of which are present in TVB. A control determination of the reactivity ratios for the styrene-p-DVB pair under different conditions (70°C., pre-gel point conversion), run for comparison with the TVB data, show values (r₁ = 0.77; r₂ = 1.46) similar to those previously recorded (r₁ = 0.77; r₂ = 2.08).     

Synthesis of styrene/methyl methacrylate copolymers by atom transfer radical polymerization: 2D NMR investigations

Copolymers of styrene and methyl methacrylate were synthesized by atom transfer radical polymerization using methyl 2‐bromopropionate as initiator and CuBr/N,N,N′,N′,N″‐pentamethyldiethylenetriamine as catalyst. Molecular weight distributions were determined by gel permeation chromatography. The composition of the copolymer was determined by ¹H NMR. The comonomer reactivity ratios, determined by both Kelen–Tudos and nonlinear error‐in‐variables methods, were r_S = 0.64 ± 0.08, r_M = 0.63 ± 0.08 and r_S = 0.66, r_M = 0.65, respectively. The α‐methyl and carbonyl carbon resonances were found to be compositionally and configurationally sensitive. Complete spectral assignments of the ¹H and ¹³C NMR spectra of the copolymers were done by distortionless enhancement by polarization transfer and two‐dimensional NMR techniques such as heteronuclear single quantum coherence and heteronuclear multiple quantum coherence. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2076–2085, 2006     

Copolymerization of isopropenyl and isopropylidene oxazolones with styrene

2-Isopropenyl-4-isopropyl-2-oxazolin-5-one (M₂), was copolymerized with styrene (M₁), and the monomer reactivity ratios were determined to be r₁ = 0.31 ± 0.03, r₂ = 1.12 ± 0.10. New isomerized oxazolones (M₂), 2-isopropylidene-4-methyl-3-oxazolin-5-one, 2-isopropylidene-4-isopropyl-3-oxazolin-5-one, and 2-isopropylidene-4-isobutyl-3-oxazolin-5-one were prepared and copolymerized with styrene. The monomer reactivity ratios were: r₁ = 0.36 = 0.07, r₂ = 0.0; r₁ = 0.39 ± 0.06, r₂ = 0.00 ± 0.10; r₁ = 0.39 ± 0.10, r₂ = 0.0, respectively. The isomerized oxazolones showed no tendency towards homopolymerization by radical initiator. From the results of infrared and NMR spectra and hydrolysis of the copolymer, it was indicated that the isomerized oxazolones participated in copolymerization in the form of 1–4 polymerization of the conjugated dienes (exo double bond at C₂ and the C?N in the ring). Copolymers reacted with nucleophilic reagents such as amines and alcohols.     

Determination of uranium and thorium in natural waters by ICP-OES after on-line solid phase extraction and preconcentration in the presence of 2,3-dihydro-9,10-dihydroxy-1,4-antracenedion

An on-line solid phase extraction method, linked to inductively coupled plasma optical emission spectrometry (ICP-OES), has been examined using octadecyl-bonded silica cartridge for determination of low levels of uranium and thorium in aqueous samples. 2,3-dihydro-9,10-dihydroxy-1,4-anthracenedion forms a hydrophobic complex with cations and the resulted complex was retained on SPE. The retained complex was eluted using an acidic solution and introduced into ICP for determination. Various effective parameters and chemical variables such as sample pH, amount of ligand (as a complexing agent), sampling and eluting flow rates and concentration of the eluent were optimized. Under optimal conditions, calibration curves with dynamic linear ranges of 1–200 μg/L (r ₂ = 0.9999) and 1–500 μg/L (r ₂ = 0.9994) for U and Th were obtained, respectively. Detection limits based on three times of standard deviations of blank by 6 replicates were 0.69 μg/L and 0.84 μg/L for U and Th, respectively. Sample throughput was 10 samples/h. The interference effects of several metal ions on percentage of recovery of U and Th were also studied. The method was applied to the recovery and sequential determination of these actinide elements in different water samples.     

Determination of the reactivity ratios of methyl acrylate with the vinyl acetate,vinyl 2,2-dimethyl-propanoate,and vinyl 2-ethylhexanoate

The course of composition drift in copolymerization reactions is determined by reactivity ratios of the contributing monomers. Since polymer properties are directly correlated with the resulting chemical composition distribution, reactivity ratios are of paramount importance. Furthermore, obtaining correct reactivity ratios is a prerequisite for good model predictions. For vinyl acetate (VAc), vinyl 2,2-dimethyl-propanoate also known as vinyl pivalate (VPV), and vinyl 2-ethylhexanoate (V2EH), the reactivity ratios with methyl acrylate (MA) have been determined by means of low conversion bulk polymerization. The mol fraction of MA in the resulting copolymer was determined by ¹H-NMR. Nonlinear optimization on the thus-obtained monomer feed–copolymer composition data resulted in the following sets of reactivity ratios: r_MA = 6.9 ± 1.4 and r_VAc = 0.013 ± 0.02; r_MA = 5.5 ± 1.2 and r_VPV = 0.017 ± 0.035; r_MA = 6.9 ± 2.7 and r_V2EH = 0.093 ± 0.23. As a result of the similar and overlapping reactivity data of the three methyl acrylate–vinyl ester monomer systems, for practical puposes these data can be described with one set of reactivity data. Nonlinear optimization of all monomer feed–copolymer composition data together resulted in r_MA = 6.1 ± 0.6 and r_VEst = 0.0087 ± 0.023. © 1994 John Wiley & Sons, Inc.     

N-vinylpyrrolidone and 4-vinyl Benzylchloride Copolymers: Synthesis,Characterization and Reactivity Ratios

The copolymers prepared in this study by free radical copolymerization of N-vinylpyrrolidone (M ₂) with 4-vinylbenzylchloride (M ₁) using 2,2′-azobisisobutyronotrile (AIBN) initiator in 1,4-dioxane solvent at 70°C were characterized by FTIR, ¹H-NMR and ¹³C-NMR techniques. Polymer solubility was tested in both polar and nonpolar solvents. The thermal properties were studied by thermogravimetric analysis (TGA) and differential scanning calorimeter (DSC). Copolymer compositions were established by H¹-NMR spectra, while reactivity ratios of the monomers were computed using the linearization methods viz., Fineman-Ross (FR) (r ₁ = 1.67 and r ₂ = 0.67), Kelen-Tudos (KT) (r ₁ = 1.77 and r ₂ = 0.65) and extended Kelen-Tudos (EK-T) (r ₁ = 1.72 and r ₂ = 0.63) methods at lower conversion. Furthermore, reactivity ratios in nonlinear error-in-variables method (RREVM) also compute the reactivity ratios (r ₁ = 1.76 and r ₂ = 0.66); these are found to be in good agreement with each other. The distribution of monomer sequence along the copolymer chain was calculated using a statistical method based on the calculated reactivity ratios.     

Ferrocene-containing polymers. II. Radiation-induced copolymerizations of ferrocenylmethyl methacrylate with styrene,methyl methacrylate,and ethyl acrylate

Ferrocenylmethyl methacrylate (FMMA) was copolymerized with styrene (St), methyl methacrylate (MMA), and ethyl acrylate (EA) in benzene solution at 25°C by γ radiation. The reactions proceeded by a free radical mechanism, and monomer reactivity ratios were derived by the Tidwell–Mortimer method for St(M₁)–FMMA(M₂), r₁ = 0.35 and r₂ = 0.46; for MMA(M₁–FMMA)(M₂), r₁ = 0.85 and r₂ = 1.36; for EA(M₁)–FMMA(M₂), r₁ = 0.36 and r₂ = 3.03. The Q and e values of FMMA determined from copolymerization with St were 0.97 and 0.55, respectively. Terpolymerization of a MMA–FMMA–EA system based on the Alfrey–Goldfinger equations was studied. This is a typical terpolymerization system in which reactivities of the monomers obey the Q–e scheme. Comparing the results obtained here with those previously reported for other monomers, we concluded that FMMA is one of the most highly reactive monomers among alkyl methacrylates.     

Copolymerization characteristics of S-vinyl-O-tert-butylthiocarbonate

Poly-S-vinyl-O-tert-butylthiocarbonate is an excellent precursor to poly(vinyl mercaptan) because the tert-butyloxycarbonyl blocking group can be removed by either acid hydrolysis or thermolysis under conditions which minimize the oxidation of the liberated mercaptan to disulfide. Dilatometric studies of the homopolymerization of S-vinyl-O-tert-butylthiocarbonate demonstrated that the polymerization rate was directly proportional to the concentration of free-radical initiator; no thermal initiation was observed. The molecular weight of the homopolymers and copolymers ranged from 30,000 to 50,000 (GPC). Copolymerization of S-vinyl-O-tert-butylthiocarbonate (M₂) with styrene, (r₁ = 3.0, r₂ = 0.2), methyl methacrylate (r₁ = 1.40, r₂ = 0.17) and vinyl acetate (r₁ = 0.04, r₂ = 11.0) indicated that a sulfur atom adjacent to the vinyl group increases the resonance stability (Q₂ = 0.5) and the electron density (e₂ = ?1.4) of the double bond and the corresponding radical. Water-soluble copolymers could be prépared by incorporating either N-vinylpyrrolidone (r₁ = 0.12, r₂ = 3.94) or N-isopropylacrylamide (r₁ = 1.17, r₂ = 0.3) with M₂. The water solubility of the copolymers decreased markedly when the tert-butyloxycarbonyl group was removed. Copolymers of M₂ with N-vinyl-O-tert-butylcarbamate (r₁ = 0.13, r₂ = 5.10) were utilized to prepare crosslinked poly(vinyl amine–vinyl mercaptan); the crosslinking resulted from urea linkages formed during thermolysis of the copolymer.     

Free-radical homopolymerization and copolymerization of vinylferrocene

The benzene solution homopolymerization of vinylferrocene, initiated by azobisisobutyronitrile, gave a series of benzene-soluble homopolymers. Thus, free-radical copolymerization studies were performed with styrene, methyl acrylate, methyl methacrylate, acrylonitrile, vinyl acetate, and isoprene in benzene. With the exception of vinyl acetate and isoprene, which did not give copolymers with vinylferrocene under these conditions, smooth production of copolymers occurred. The relative reactivity ratios, r₁ and r₂, were obtained for vinylferrocene–styrene copolymerizations by using the curve-fitting method for the differential form of the copolymer equation, by the Fineman-Ross technique, and by computer fitting of the integrated form of the copolymer equations applied to higher conversion copolymerizations. In styrene (M₂) copolymerizations, the curve-fitting and Fineman-Ross methods both gave r₁ = 0.08, r₂ = 2.50, while the integration method gave r₁ = 0.097, r₂ = 2.91. Application of the integration method to methyl acrylate and methyl methacrylate (M₂) gave values of r₁ = 0.82, r₂ = 0.63; r₁ = 0.52, r₂ = 1.22, respectively. The curve-fitting method gave r₁ = 0.15, r₂ = 0.16 for acrylonitrile (M₂) copolymerizations. From styrene copolymerizations, vinylferrocene exhibited values of Q = 0.145 and e = 0.47.     

Synthesis of Graft Polymers by Copolymerization of Macromonomers. II. Copolymerization Kinetics of Styrene-and Methacrylate-Terminatedpoly(2-Acetoxyethyl Methacrylate) Macromonomers

Styrene-terminated poly(2-acetoxyethyl methacrylate) macromonomer (EBA), methacrylate-terminated poly(2-acetoxyethyl methacrylate) macromonomer (MPA), and methacrylate-terminated poly(methyl methacrylate) macromonomer (MPM) were synthesized and subjected to polymerization and copolymerization by a free-radical polymerization initiator (AIBN). EBA and MPA were homopolymerized at various concentrations. EBA exhibited higher reactivity than styrene. The reactivity of MPA, however, was almost equal to that of glycidyl methacrylate. Cumulative copolymer compositions were determined by GPC analysis of copolymerization products. The reactivity ratios estimated were r_a = 0.95 and r_b , = 0.90 for EBA macromonomer (a)-methyl methacrylate (b) copolymerization. These values were not consistent with literature values for the styrene-methyl methacrylate and p-methoxy-styrene-methyl methacrylate systems. The reactivity ratios estimated for MPA and 2-bromoethyl methacrylate were r_a - 0.95 and r_b , = 0.98; equal to the glycidyl methacrylate-2-bromoethyl methacrylate system. MPA or MPM was also copolymerized with styrene, and the reactivity ratios were r_a = 0.40, r_a = 0.60 and r_a = 0.39, r_a = 0.58, respectively. These estimates were in good agreement with the reactivity ratios for glycidyl methacrylate and styrene. Thus, no effect of molecular weight was observed for both copolymerization systems.     

Synthesis and Polymerization of Optically Active Di-L-Menthyl Itaconate

Optically active di-L-menthyl itaconate (DMI) was prepared from itaconic acid and L-menthol. DMI was polymerized in bulk at 80°C to give a chiral homopolymer having a specific rotation of -76.9°. DMI (M ₁) was copolymerized with styrene (ST, M ₂), N-cyclohexylmaleimide (CHMI, M ₂), vinyl acetate (VAc, M ₂) and methyl methacrylate (MMA, M ₂) with azobisisobutyronitrile in benzene at 50°C. The monomer reactivity ratios (r ₁, r ₂) and Alfrey-Price Q, e values were determined as r ₁ = 0.56, r ₂ = 0.55, Q ₁ = 0.76, e ₁ = 0.29 for DMI-ST; r ₁ = 0.0, r ₂ = 5.6 for DMI-MMA; r ₁ = 0.0, r ₂ = 0.25 for DMI-VAc; and r ₁ = 0.31, r ₂ = 0.56 for DMI-CHMI. The chiroptical properties of the polymers were investigated.     

Non-uniqueness in determination of terminal and penultimate model reactivity ratios in the styrene-methyl methacrylate free-radical copolymerization system

The terminal and penultimate model reactivity ratios in the free-radical copolymerization of styrene and methyl methacrylate in bulk at 40°C were calculated by means of the simplex and scanning methods. Calculations showed that for the terminal model r₁ and r₂ vary in comparatively narrow ranges of 0.548–0.552 and 0.480–0.483, respectively. For the penultimate model, the most accurate reactivity ratios calculated by the simplex method, which were r₁₁ = 0.727, r₂₂ = 0.490, r₂₁ = 2.890, r₁₂ = 4.583, are surrounded with sets of reactivity ratio values of equal accuracy. The ranges of variation were found to be 0.711–0.746, 0.487–0.492, 2.810–2.970 and 4.213–5.049, respectively. Numerical values of the penultimate r-parameters calculated with the simplex method depend, due to the structure of the multidimensional space (r₁₁, r₂₂, r₂₁, r₁₂, σ), on the initial guess for the r-parameters. Use of the covariance matrix for the estimation of the indetermination ranges is discussed.