Nonisothermal cold crystallization behavior and kinetics of polylactide/clay nanocomposites

The nonisothermal cold crystallization behavior of intercalated polylactide (PLA)/clay nanocomposites (PLACNs) was studied using differential scanning calorimetry, polarized optical microscope, X‐ray diffractometer, dynamic mechanical thermal analysis, and Fourier transform infrared spectrometer. The results show that both the cold crystallization temperature (T_cc) and melting point (T_m) of PLA matrix decreases monotonously with increasing of clay loadings, accompanied by the decreasing degree of crystallinity (X_c%) at the low heating rates (≤5 °C/min). However, the X_c% of PLACNs presents a remarkable increase at the high heating rate of 10 °C/min in contrast to that of neat PLA. The crystallization kinetics was then analyzed by the Avrami, Jezioney, Ozawa, Mo, Kissinger and Lauritzen–Hoffman kinetic models. It can be concluded that at the low heating rate, the cold crystallization of both the neat PLA and nanocomposites proceeds by regime III kinetics. The nucleation effect of clay promote the crystallization to some extent, while the impeding effect of clay results in the decrease of crystallization rate with increasing of clay loadings. At the high heating rate of 10 °C/min, crystallization proceeds mainly by regime II kinetics. Thus, the formation of much more incomplete crystals in the PLACNs with high clay loadings due to the dominant multiple nucleations mechanism in regime II, may have primary contribution to the lower crystallization kinetics, also as a result to the higher degree of crystallinity and lower melting point in contrast to that of neat PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1100–1113, 2007     

Characterization,crystallization kinetics,and melting behavior of poly(ethylene succinate) copolyester containing 10 mol % butylene succinate

Copolyester was synthesized and characterized as having 89.9 mol % ethylene succinate units and 10.1 mol % butylene succinate units in a random sequence, as revealed by NMR. Isothermal crystallization kinetics was studied in the temperature range (T_c) from 30 to 73 °C using differential scanning calorimetry (DSC). The melting behavior after isothermal crystallization was investigated using DSC by varying the T_c, the heating rate and the crystallization time. DSC curves showed triple melting peaks. The melting behavior indicates that the upper melting peaks are associated primarily with the melting of lamellar crystals with various stabilities. As the T_c increases, the contribution of recrystallization slowly decreases and finally disappears. A Hoffman‐Weeks linear plot gives an equilibrium melting temperature of 107.0 °C. The spherulite growth of this copolyester from 80 to 20 °C at a cooling rate of 2 or 4 °C/min was monitored and recorded using an optical microscope equipped with a CCD camera. Continuous growth rates between melting and glass transition temperatures can be obtained after curve‐fitting procedures. These data fit well with those data points measured in the isothermal experiments. These data were analyzed with the Hoffman and Lauritzen theory. A regime II → III transition was detected at around 52 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2431–2442, 2008     

Analysis of crystallization kinetics of poly(ether ether ketone)

An optical microscope equipped with a video photograph system was used to follow the growth of spherulites. Under nitrogen atmosphere, the growth rates at 290 and 300°C suggest that when the melt of PEEK has been equilibrated for 15 min at 400°C, the subsequent crystallization behavior was nearly independent of the prior thermal history. Linear growth rates of crystallization of PEEK have been measuredin the temperature range of 260–325°C for melt-pressed films and solvent cast films. Detailed kinetic analysis indicated that PEEK exhibited an unmistakable regime II → III transition at 296 ± 1°C. The II → III transition was clearly present irrespective of the rather drastic changes in U*. It is interesting that the branching and crosslinking retarded the growth rate of PEEK, but a transition from regime II to regime III still existed. For melt-pressed films after equilibration at 400°C for 15 min, values of σ and q suggest that U* should be taken nearer to 1500 cal/mol in the case of T_∞ = T_g − 30 K and 2000 cal/mol in the case of T_∞ = T_g − 51.6 K. The K_g(III)/K_g(II) ratio (1.32) was not as close to the predicted value of 2 as was Hoffman's ratio. For PEEK, the Thomas-Staveley constant (β) should be closer to 0.25 or 0.3 instead of 0.1. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1335–1348, 1998     

Crystallization kinetics and melting behavior of metallocene short‐chain branched polyethylene fractions

Metallocene polyethylene (mPE) fractions are recognized as being more homogeneous with respect to short‐chain branch (SCB) distribution as compared with unfractionated mPEs. Differential scanning calorimetry and polarized optical microscopy (POM) were used to study the influences of SCB content on the crystallization kinetics, melting behavior, and crystal morphology of four butyl‐branched mPE fractions. The parent mPE of the studied fractions was also investigated for comparative purposes. mPE fractions showed a much simpler crystallization behavior as compared with their parent mPE during the cooling experiments. The Ozawa equation was successfully used to analyze the nonisothermal crystallization kinetics of the fractions. The Ozawa exponent n decreased from about 3.5 to 2 as the temperature declined for each fraction, indicating the crystal‐growth geometry changed from three‐dimensional to two‐dimensional. For isothermal crystallization, the fraction with a lesser SCB content exhibited a higher crystallization temperature (T_c) window. The results from the Avrami equation analysis showed the exponent n values were around 3 (with minor variation), which implied that the crystal‐growth geometry is pseudo‐three‐dimensional. Both of the activation energies for nonisothermal and isothermal crystallization were determined for each fraction with Kissinger and Arrhenius‐type equations, respectively. Double melting peaks were observed for both nonisothermally or isothermally crystallized specimens. The high‐melting peak was confirmed induced via the annealing effect during heating scans. The Hoffman–Weeks plot was inapplicable in obtaining the equilibrium melting temperature (T_m°) for each fraction. The relationship between T_c and T_m for the fractions is approximately T_m = T_c (°C) + 8.3. The POM results indicated that the crystals of parent or fractions formed under cooling conditions did not exhibit the typical spherulitic morphology as a result of the high SCB content. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 325–337, 2002     

High-temperature aging of Halar film. II. Analysis of melting behavior

Melting behavior of an experimental Halar film, a predominantly alternating 1:1 copolymer of ethylene (E) and chlorotrifluoroethylene (CTFE), has been studied. Differential scanning calorimetry (DSC) reveals single or double melting peaks, depending upon the thermal history. The lower-temperature melting peak T_m1 is produced only by the thermal treatment and shows a strong dependence on annealing time and temperature. On the basis of the DSC and x-ray data it can be suggested that T_m1 represents the melting of relatively small crystallites formed upon annealing. The higher-temperature melting peak T_m2 is always shown at 238°C. (Note: the specification for commercial Halar product is 240°C. The slightly lower melting temperature reported in this study is probably due to the fact that we are dealing with an experimental melt-processed material.) On the basis of the heating rate study we propose that Halar crystallizes with stable crystals (T_m2 = 238°C) regardless of the crystallization conditions, i.e., quenching, slow cooling, or even annealing. Crystals of Halar have a heat of fusion of approximately 35 cal/g or 146 kJ/kg. Detailed analysis of the melting behavior of Halar is presented.     

Thermal analysis of the double-melting behavior of poly(L-lactic acid)

The melting and crystallization behavior of poly(L -lactic acid) (PLLA; weight-average molecular weight = 3 × 10⁵) was studied with differential scanning calorimetry (DSC). DSC curves for PLLA samples were obtained at various cooling rates (CRs) from the melt (210 °C). The peak crystallization temperature and the exothermic heat of crystallization determined from the DSC curve decreased almost linearly with increasing log(CR). DSC melting curves for the melt-crystallized samples were obtained at various heating rates (HRs). The double-melting behavior was confirmed by the double endothermic peaks, a high-temperature peak (H) and a low-temperature peak (L), that appeared in the DSC curves at slow HRs for the samples prepared with a slow CR. Peak L increased with increasing HR, whereas peak H decreased. The peak melting temperatures of L and H [T_m(L) and T_m(H)] decreased linearly with log(HR). The appearance region of the double-melting peaks (L and H) was illustrated in a CR–HR map. Peak L decreased with increasing CR, whereas peak H increased. T_m(L) and T_m(H) decreased almost linearly with log(CR). The characteristics of the crystallization and double-melting behavior were explained by the slow rates of crystallization and recrystallization, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 25–32, 2004     

Ultrahigh Molecular mass Polyethylene/ Carbon Nanotube CompositesCrystallization and melting properties

Ultrahigh molecular mass polyethylene (UHMMPE) is filled with carbon nano-tubes (CNTs) by solution in the presence of maleic anhydride grafted styrene-(ethylene-co-butylene)-styrene copolymer (MA-SEBS) as a compatibilizer. The UHMMPE/CNT composites crystallized from melt were prepared at a cooling rate of 20°C min^-1. The melting and crystallization behaviors of UHMMPE/ CNT composites were investigated by differential scanning calorimetry. The results showed that onset melting temperature (T _m) and degree of crystallinity (X _c) of UHMMPE/CNT composites crystallized from solution are higher than those from melt due to the larger crystalline lamellar thickness. The onset crystallization temperature (T _c) of UHMMPE/CNT composites tends to shift to higher temperature region with increasing CNT content in the composites. Tm and Tc of UHMMPE phase in UHMMPE/CNT composites decrease with the addition of MA-SEBS. Moreover, the crystallization rate of UHMMPE phase in UHMMPE/CNT composite is increased due to the introduction of CNTs. MA-SEBS acts as compatilizer, enhances the dispersion of CNTs in the UHMMPE matrix. Thereby, the crystallization rate of UHMMPE phase in UHMMPE/CNT composite is further increased with the addition of MA-SEBS. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis and comparative study of biodegradable poly(alkylene sebacate)s

Novel biodegradable polyesters, such as poly(ethylene sebacate) (PESeb), poly(propylene sebacate) (PPSeb), and poly(butylene sebacate) (PBSeb), were synthesized and studied with respect to melting behavior, crystallization kinetics, and enzymatic hydrolysis. PESeb and PPSeb showed multiple melting behavior. Wide angle X‐ray diffractometry measurements at various temperatures, standard, step‐scan, and high‐rate differential scanning calorimetry methods were applied to elucidate the appearance of multiple endotherms in heating scans, which was interpreted in the context of partial melting‐recrystallization and final melting. PBSeb did not show any multiple melting behavior but only a weak tendency for recrystallization on heating. The melting temperatures of PESeb, PPSeb, and PBSeb were measured equal to 78, 57, and 71 °C, respectively. The equilibrium melting points were estimated to be T_m° = 90.2, 69.9, and 77.4 °C for PESeb, PPSeb, and PBSeb, while the corresponding enthalpy of fusion values were found to be ΔH_f = 170 ± 10, 140 ± 10, and 155 ± 10 J/g, respectively. The polyesters showed fast crystallization rates under both isothermal and nonisothermal conditions. Crystallization kinetics was thoroughly investigated using macrokinetic models and isoconversional analysis. Enzymatic hydrolysis rate in the presence of lipases Rhizopus delemar and Pseudomonas cepacia was found to be fast for PPSeb, whereas PESeb and PBSeb showed slow rates and comparable with those of PCL. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 672–686, 2010     

Melting behavior of poly(ether ether ketone) in its blends with poly(ether imide)

We detail the melting behavior of poly(ether ether ketone) (PEEK) and investigate its melting behavior in miscible blends with poly(ether imide) (PEI). The determination of the equilibrium melting point (T_m⁰) of PEEK is discussed by considering its inhomogeneous morphology. T_m⁰ is obtained by a long extrapolation of a Hoffman–Weeks plot to 384°C. Hindrance of PEEK crystal reorganization induced by PEI during heating is observed over the blend composition investigated (20–75 wt % PEEK). This behavior is correlated with the incorporation of PEI in the interlamellar zones of PEEK crystals. The interaction parameter χ of PEEK/PEI blends is estimated by the equilibrium melting point depression. This gives the interaction density B = ?1.2 cal/cm³, and x = ?0.40 at 400°C. © 1993 John Wiley & Sons, Inc.     

Melting behavior of isotactic polystyrene

The melting behavior of isotactic polystyrene, crystallized from the melt and from dilute solutions in trans-decalin, has been studied by differential scanning calorimetry and solubility measurements. The melting curves show 1, 2, or 3 melting endotherms. At large supercooling, crystallization from the melt produces a small melting endotherm just above the crystallization temperature T_c. This peak originates from secondary crystallization of melt trapped within the spherulites. The next melting endotherm is related to the normal primary crystallization process. Its peak temperature increases linearly with T_c, yielding an extrapolated value for the equilibrium melting temperature T_c° of 242 ± 1°C as found before. By self-seeding, crystallization from the melt could be performed at much higher temperature to obtain melting temperatures as high as 243°C, giving rise to doubt about the value of T_c° found by extrapolation. For normal values of T_c and heating rate, an extra endotherm appears on the melting curve. Its peak temperature is the same for both melt-crystallized and solution-crystallized samples, and independent of T_c, but rises with decreasing heating rate. From the effects of heating rate and partial scanning on the ratio of peak areas and of previous heat treatment on dissolution temperature, it is concluded that this peak arises from the second one by continuous melting and recrystallization during the scan.     

Thermal behavior of polytriazole films: A thermal analysis study

The thermal behavior of poly(1,3-phenyl-1,4-phenyl)-4-phenyl-1,2,4-triazole has been investigated using different scanning calorimetry (DSC) and thermogravimetry (TG). Processes are studied for this thermally stable polymer that take place between 200 and 500°C. While the polycondensation reaction product in powder from appeared to be partially crystalline, films prepared by casting from a formic acid solution appeared to be completely amorphous. A thermal treatment between T_g(～ 270°C) and T_m(～ 430°C) can introduce crystallinity in the films because of the polymer's ability to cold crystallize. The cold crystallization temperature T_c seems to be dependent on the preparation history of the solid polymer phase. Thermal annealing of the films just below T_g does not introduce crystallinity but inhibits subsequent cold crystallization at higher temperatures. Crystallization upon cooling from the crystalline melt has not been observed either. At temperatures just above the crystalline melting point the polymer starts to decompose in an exothermic reaction.     

Multiple melting behavior of poly(butylene succinate). II. Thermal analysis of isothermal crystallization and melting process

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights (MWs) of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were isothermally crystallized at various crystallization temperatures (T_c) ranging from 70 to 97.5 °C. The T_c dependence of crystallization half‐time (τ) was obtained. DSC melting curves for the isothermally crystallized samples were obtained at a heating rate of 10 K min⁻¹. Three endothermic peaks, an annealing peak, a low‐temperature peak L, and a high‐temperature peak H, and an exothermic peak located between peaks L and H clearly appeared in the DSC curve. In addition, an endothermic small peak S appeared at a lower temperature of peak H. Peak L increased with increasing T_c, whereas peak H decreased. The T_c dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of T_c. T_m(L), T_re, and ΔH increased almost linearly with T_c, whereas T_m(H) was almost constant. The maximum rate of recrystallization occurred immediately after the melting. The mechanism of the multiple melting behavior is explained by the melt‐recrystallization model. The high MW samples showed similar T_c dependence of τ, and τ for the lowest MW sample was longer than that for the others. Peak L increased with MW, whereas peak H decreased. In spite of the difference of MW, T_m(L), T_m(H), and T_re almost coincided with each other at the same T_c. The ΔH values, that is crystallinity, for the highest MW sample were smaller than those for the other samples at the same T_c. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2039–2047, 2005     

The equation of state and heat of fusion of poly(ether ether ketone)

The pressure-volume-temperature properties of poly(ether ether ketone) (PEEK) were studied experimentally at temperatures of 400°C and pressures to 200 MPa. Specific volume data were fitted successfully to the empirical Tait equation for T < T_g and T > T_m and to the theoretical Simha-Somcynsky equation of state for the melt. The pressure dependence of the glass-transition temperature is about 0.57–0.59°C/MPa and that of the melting point 0.483°C/MPa. The pressure dependence of the melting point, the specific volume of the melt at T_m, and the specific volume of the crystal at T_m determined from x-ray diffraction data at elevated temperatures were combined in the Clapeyron equation to calculate a heat of fusion of 161 ± 20 J/g for the PEEK crystal. This value is somewhat higher than the previously reported value of 130 J/g.     

Stepwise annealing of poly(butylene terephthalate)

Annealing of poly(butylene terephthalate) (PBT) was studied by differential scanning calorimetry (DSC) and small angle X‐ray scattering (SAXS) measurement. A PBT sample was annealed at a recrystallization temperature where recrystallization occurs with a maximum rate in the heating process of the sample. In the subsequent annealing steps, the annealed sample was annealed repeatedly at the recrystallization temperatures, and the stepwise annealing sample was obtained. Peak melting temperature (T_m) and sharpness of DSC peak of the stepwise annealing sample increased with the annealing step. A high melting‐temperature sample was obtained in a short time, and T_m increased up to 238.5°C which is higher than all the T_m values that appear in the literature. The long period calculated from SAXS curves of the stepwise annealing sample increased with the annealing step. The increase of crystallite size and perfection of the crystal in the stepwise annealing process is suggested. Annealing experiment indicated that T^°_m should be higher than about 235°C. T_m increased linearly with the annealing temperature of the final step in the stepwise annealing (T_a). The equilibrium melting temperature (T^°_m) for PBT was estimated to be 247°C by the application of a Hoffman–Weeks plot to the relation between T_m vs. T_a. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2420–2429, 1999     

Nonisothermal crystallization kinetics of in situ nylon 6/graphene composites by differential scanning calorimetry

The nonisothermal crystallization kinetics was investigated by differential scanning calorimetry for the nylon 6/graphene composites prepared by in situ polymerization. The Avrami theory modified by Jeziorny, Ozawa equation, and Mo equation was used to describe the nonisothermal crystallization kinetics. The analysis based on the Avrami theory modified by Jeziorny shows that, at lower cooling rates (at 5, 10, and 20 K/min), the nylon 6/graphene composites have lower crystallization rate than pure nylon 6. However, at higher cooling rates (at 40 K/min), the nylon 6/graphene composites have higher crystallization rate than pure nylon 6. The values of Avrami exponent m and the cooling crystallization function F(T) from Ozawa plots indicate that the mode of the nucleation and growth at initial stage of the nonisothermal crystallization may be as follows: two‐dimensional (2D), then one‐dimensional (1D) for all samples at 5–10 °C/min; three‐dimensional (3D) or complicated than 3D, then 2D and 1D at 10–20 and 20–40 °C/min. The good linearity of the Mo plots indicated that the combined approach could successfully describe the crystallization processes of the nylon 6 and nylon 6/graphene composites. The activation energies (ΔE) of the nylon 6/graphene composites, determined by Kissinger method, were lower than those of pure nylon 6. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1381–1388, 2011     

Morphology of polylactic acid crystallized during annealing after uniaxial deformation

Uniaxial deformation of amorphous L -polylactic acid films was performed at two different temperatures at which thermal degradation was minimal, 70 °C or T_g + 10 and 90 °C or T_g + 30. Samples were annealed postdeformation for long times (either 15 or 45 min) to approach equilibrium conditions. Samples deformed and annealed at 70 °C showed low crystallinity and poor crystalline order or crystal size, as determined by wide-angle X-ray diffraction. At 90 °C, high crystallinity and order parameters were observed. In addition, once the oriented chains had crystallized at this temperature, nonoriented chains also underwent crystallization, and a small fraction of nonordered crystal phase was therefore observed after long annealing times. These observations are explained on the basis of different morphologies in samples drawn at the two temperatures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Transitions and relaxations in poly(1,4-phenylene ether)

Transitions and relaxation phenomena in poly(1,4-phenylene ether) were studied over temperature range from 100 to 800°K by applying a combination of calorimetric, dilatometric, dynamic mechanical, and dielectric techniques. Amorphous polymer, exhibiting no x-ray crystallinity, is obtained only by quenching molten samples at extremely fast cooling rates (ca. 1000°C/sec) and by minimizing thermal gradients within specimens. A weakly active mechanical relaxation region with a loss maximum at 155°K of unknown origin was observed. The glass transition interval of completely amorphous polymer is characterized by a discontinuous jump in heat capacity of 2.76 cal/deg per chain segment occurring at 363°K (corrected for kinetic effects), and a fourfold increase in the coefficient of linear thermal expansion. Strongly active, dynamic mechanical relaxations occur in the T_g interval with a loss maximum at 371°K (f = 110 cps) and resulting in a drop in the dynamic storage modulus from 10¹¹ to 10⁹ dyne/cm². Cold crystallization takes place just above T_g, to yield a polymer with an x-ray crystallinity of 0.7 and a heat of crystallization of 270 cal/mole. The crystalline polymer shows a complex melt structure. Depending upon the thermal history, multiple endothermic peaks indicative of structural reorganizations occur just prior to fusion. Very high dielectric losses with a wide distribution of relaxation times were observed in the melt interval. The mechanical relaxation spectrum in this region is typical of viscous flow behavior.     

Superdrawing of polytetrafluoroethylene virgin powder above the static melting temperature

A new two‐stage draw technique was successfully applied to the superdrawing of polytetrafluoroethylene (PTFE) virgin powder. A film, compression‐molded from powder below the melting temperature (T_m = 335 °C), was initially solid‐state coextruded to an extrusion draw ratio (EDR) of 6–20 at 325 °C, about 10 °C below the T_m. These extrudates from the first‐stage draw were further drawn by a second‐stage pin draw in the temperature (T_d) range of 300–370 °C that covers the static T_m. The maximum achievable total draw ratio was ～60 at a T_d = 300 °C and increased rapidly with increasing T_d, reaching a maximum of 100–160 at a temperature window between 340 and 360 °C, depending on the initial EDRs. At yet higher T_d's, the ductility was lost as a result of melting. The high ductility of the PTFE extrudates at such high temperatures was ascribed to the improvement of interfacial adhesion and bonding between the deformed powder particles upon the first‐stage extrusion combined with the rapid heating of only a portion of the extrudate followed by the elongation at a high rate. The highly drawn fibers were highly crystalline (χ_c ≤ 87%) and showed high chain orientation (f_c ≤ 0.997) and a large crystallite size along the chain axis (D₀₀₁₅ ≤ 160 nm). The molecular draw ratio, estimated from the entropic shrinkage above the T_m, was close to the macroscopic deformation ratio independently of the initial EDRs. These results indicate that the draw was highly efficient in terms of chain extension, orientation, and crystallization. Thus, the maximum tensile modulus and strength achieved in this work were 102 ± 5 and 1.4 ± 0.2 GPa, respectively, at 24 °C. These tensile properties are among the highest ever reported on oriented PTFE. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1995–2004, 2001     

Revisiting the crystallization of poly(2‐alkyl‐2‐oxazoline)s

Poly(2‐alkyl‐2‐oxazoline)s (PAOx) exhibit different crystallization behavior depending on the length of the alkyl side chain. PAOx having methyl, ethyl, or propyl side chains do not show any bulk crystallization. Crystallization in the heating cycle, that is, cold crystallization, is observed for PAOx with butyl and pentyl side chains. For PAOx with longer alkyl side chains crystallization occurs in the cooling cycle. The different crystallization behavior is attributed to the different polymer chain mobility in line with the glass transition temperature (T_g) dependency on alkyl side chain length. The decrease in chain mobility with decreasing alkyl side chain length hinders the relaxation of the polymer backbone to the thermodynamic equilibrium crystalline structure. Double melting behavior is observed for PButOx and PiPropOx which is explained by the melt‐recrystallization mechanism. Isothermal crystallization experiments of PButOx between 60 and 90 °C and PiPropOx between 90 and 150 °C show that PAOx can crystallize in bulk when enough time is given. The decrease of T_g and the corresponding increase in chain mobility at T > T_g with increasing alkyl side chain length can be attributed to an increasing distance between the polymer backbones and thus decreasing average strength of amide dipole interactions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 721–729     

SAXS and DSC studies of the crystallization and melting phenomena of poly(ϵ‐caprolactone)

The relationships between the crystallization temperature, T_c, the crystal thickness, d_c and the melting peak temperature, T_m of poly(ϵ‐caprolactone) have been determined by carrying out time‐ and temperature‐dependent small angle x‐ray scattering experiments. A two‐step melting has been suggested, resulting in the occurrence of two well defined independent boundary lines, indicating the transformation from melt into the partially crystalline state. For crystallization temperatures lower than 40°C, during heating, more pronounced peak shifts are observed with the final melting of the crystallites having the same thickness of d_c ≈︁ 7 nm. In this region, it is evident that crystals have relatively good stabilities, since they have fairly uniform thickness. At higher temperatures, above 40°C, T_m increases with T_c, together with the thickness. The transformation of the melt into the partially crystalline state depicts a two‐step process, beginning with the formation of a well defined initial structure with lower order, which is subsequently stabilized.