Sonoelectroanalysis: Anodic Stripping Voltammetric Determination of Cadmium in Whole Human Blood

The quantitative detection of cadmium in human blood is shown to be possible by anodic stripping voltammetry under conditions of insonation. An immersion horn probe is introduced into a thermostatted conventional three‐electrode cell opposite a Nafion‐coated mercury plated glassy carbon electrode. The enhanced mass transport associated with power ultrasound yields efficient preconcentration of the cadmium before it is detected using anodic differential‐pulse stripping voltammetry. Insonation further offers the crucial benefits of first surface activation and cleaning, helping to prevent electrode fouling by the organic components in blood and second fully equilibrating “free” and “bound” Cd²⁺ ions in the complex matrix. Acoustic streaming and cavitation promote the mass transport of cadmium to the surface of electrode, facilitating measurements in solutions of low cadmium concentration, where “silent” measurements fail to yield an analytical signal. The system is calibrated using standard micro additions of cadmium to give the total amount of cadmium in blood. The calibration plot, showing the dependence of the cadmium stripping peak height on cadmium concentration in 1 : 50 diluted blood samples, was linear in the range 1×10^?10 M to 4×10^?9 M Cd²⁺. The values of cadmium concentration obtained using sonoelectroanalytical methodology were compared with the results obtained by independent atomic absorption spectroscopy (AAS) measurements and good agreement was found.     

Anodic Stripping Voltammetry Using a Vibrating Electrode

This work proposes a vibrating microwire electrode as working electrode in stripping voltammetry. The vibration was found to maintain a constant and thin (1–2 μm) diffusion layer during the deposition step. The electrode vibration eliminated the need for external stirring of the solution, thus facilitating in situ detection in the environment. The vibration was effected by fixing a low‐voltage (3 V), asymmetric, electrical rotor to the working electrode (a gold microwire of either 5 or 25 μm). The sensitivity of the vibrated electrode was ca. 22×greater than stationary. Measurements of copper (4 nM) by anodic stripping voltammetry using the vibrating electrode had a low standard deviation (1% for n=6) indicating that the diffusion layer had only minor variability. The agitation mechanism was unaffected by water moving at >2 m s^?1 and by water pressure equivalent to a depth of >40 m, indicating its suitability for in situ measurements. The vibrating probe was used for in situ detection of copper by anodic stripping voltammetry to a depth of 6 m. Using a 5 min deposition time, the limit of detection for labile copper was 38 pM.     

The Use of the Bismuth Film Electrode for the Anodic Stripping Voltammetric Determination of Tin

Bismuth coated glassy carbon electrodes have been applied to the square‐wave anodic stripping voltammetry (SWASV) of trace concentrations of tin. Optimization of Bismuth Film Electrode (BFE) performance was conducted after initial comparison with the more traditional mercury electrode. Simultaneous deposition of tin and bismuth at ?1.3 V for 2 minutes in a supporting electrolyte of 2.5 M sodium bromide utilizing a square‐wave stripping step, allowed analysis of tin at the μg L^?1 level. Parameters, such as deposition potential and time, bismuth concentration, square‐waveform settings including amplitude, step height and frequency were studied and optimized. The dependence of stripping current on deposition time indicates that using longer deposition time should facilitate sub μg L^?1 analysis. Tin was analyzed simultaneously with cadmium and either indium or thallium; Where as lead and copper were not resolved from the stripping peaks of tin and bismuth respectively. Finally, the method was applied to the analysis of tin in fruit juice.     

Recent Advances in Anodic Stripping Voltammetry with Bismuth‐Modified Carbon Paste Electrodes

In this article, the results of some recent investigations on two types of bismuth‐modified carbon paste electrodes are presented. In the first study, the bismuth‐film carbon paste electrode (BiF‐CPE) operated in situ and employed in anodic stripping voltammetry of Cd(II) and Pb(II) at the low μg L^?1 level was of interest in view of choosing the proper Bi(III)‐to‐Me(II) concentration ratios (where Me: Pb or Cd). Such optimization has resulted in significant improvement of detection limits down to 1.0 μg L^?1 Cd and 0.8 μg L^?1 for Pb, which allowed us to apply the BiF‐CPE for analysis of selected real samples of tap and sea water. The BiF‐CPE was also further investigated for its application in highly alkaline media. In this case, attention was focused on the complex‐forming capabilities of the OH ^– ions and their effect on the anodic stripping characteristics of some heavy metals (i.e. Cd, Pb, Tl) as well as upon the formation of the bismuth film itself. The last example deals with the continuing characterization of the recently introduced carbon paste electrodes modified with bismuth powder (Bi‐CPEs) which combine the advantageous properties of carbon paste material with the favorable electrochemical properties of bismuth. Three series of electrodes, differing either in the content of metallic bismuth (from 8 to 50% w/w) or in the type of the carbon powder used (two spectroscopic types of graphite and powdered glassy carbon), were compared and the respective relations to the optimal carbon paste composition evaluated. Attractive electroanalytical performance of the Bi‐CPE in anodic stripping voltammetry is demonstrated for selected model mixtures of heavy metals (Mn, Zn, Cd, Pb, Tl, and In).     

Simultaneous Determination of Copper and Bismuth by Anodic Stripping Voltammetry Using H‐Point Standard Addition Method with Simultaneous Addition of Analytes

Simultaneous determination of bismuth and copper by anodic stripping voltammetry using H‐point standard addition method (HPSAM) with simultaneous addition of analytes is described. The effect of various parameters including acid concentration, accumulation time, accumulation potential and concentration ratio of analytes in the standard solution on the sensitivity and accuracy of method were investigated. The results of applying the H‐point standard addition method showed that Cu²⁺ and Bi³⁺ could be determined simultaneously with the concentration ratios of Cu²⁺ to Bi³⁺ varying from 1 : 15 to 16 : 1 in the mixed sample. The method was successfully applied to the simultaneous determination of copper and bismuth in some synthetic mixtures.     

Enhanced Resolution of Copper and Bismuth by Addition of Gallium in Anodic Stripping Voltammetry with the Bismuth Film Electrode

This paper presents the enhanced analysis of copper on a bismuth electrode upon addition of gallium(III). The presence of gallium alleviates the problems of overlapping stripping signals usually observed between copper and bismuth when using the Bismuth Film Electrode. In addition, it has been found that the presence of gallium improves the reproducibility of the bismuth stripping signal. Simultaneous deposition of copper and bismuth at ?1500 mV for 2 minutes in a supporting electrolyte composed of 0.1 M pH 4.75 acetate buffer with 250 μg L^?1 gallium yields well resolved copper and bismuth signals when analyzed with square‐wave anodic stripping voltammetry. Simultaneous analysis of copper and lead yielded linear calibration plots in the range 10 to 100 μg L^?1 with regression coefficients of 0.997 and 0.994 respectively. The theoretical detection limit for copper was calculated to be 4.98 μg L^?1 utilizing a 2 minutes deposition time. The relative standard deviation for a copper concentration of 50 μg L^?1 was 1.6% (n=10).     

Determination of sub-micromolar amounts of sulfide by standard free anodic stripping voltammetry and anodic stripping voltammetric titration

A novel electrochemical methods namely standard free anodic stripping voltammetry and anodic stripping voltammetric titration are proposed for determination of dissolved sulfide concentration. 2Ag⁺ + S²⁻ → Ag₂S reaction is used to provide the information. The anodic stripping voltammetric response of unreacted silver-ions at the glassy carbon electrode is used as analytical signal. Results reliability and accuracy are confirmed by analysis of model solutions, spiked natural and tap waters and recovery study, with a recovery of 100 ± 5% (n = 7) obtained. The approaches show the detection limit (3σ_blank) of 2-5 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of 2-5% for repeated measurements.     

Anodic Stripping Voltammetry: Arsenic Determination in Ancient Bone Samples

Abstract

A highly sensitive method for the determination of arsenic (As) content in ancient bone samples was studied using a gold tipped rotating disc electrode and differential pulse anodic stripping voltammetry. Factors affecting sensitivity and precision, including electrolyte concentration, deposition potential, deposition time, and rotation rate were investigated. Electroinactive As(V) was reduced to As(III) by HCl 30% w/v prior to electroanalytical measurements. For a deposition time of 120 sec, the lowest detection limit (LOD) for arsenic was 1.078 µg/L. Optimized working conditions are defined as a deposition potential of ?1200 mV with a deposition time of 120 sec, 10 M HCl as the supporting electrolyte, and a rotation rate of 2000 rpm. Results of electroanalytial measurements in ancient bone samples are compared with those obtained from the hydride generation atomic absorption spectroscopy (HG‐FAAS) analysis. Analytical relevancy of the two methods was then compared with the aid of statistical data treatment.     

A Study of the Determination of Cu(II) by Anodic Stripping Voltammetry on a Novel Nylon/Carbon Fiber Electrode

In this work we report a new electrode material formed by injection‐moulding of a conducting polymer consisting of carbon fibers in a Nylon matrix. This material is highly conductive, inexpensive, easy to mould in different shapes and requires minimal pretreatment. The electrode was tested as a mercury‐free sensor for the trace determination of Cu(II) by anodic stripping voltammetry (ASV). The deposition and stripping behavior of copper on the conducting material was initially studied by cyclic voltammetry and the chemical and instrumental parameters of the determination were investigated. The electrode has been shown to be suitable for the determination of Cu(II) in the range 8 μg L^?1 to 30 mg L^?1 (with deposition times ranging from 30 s to 10 min) with a relative standard deviation of 2.2% (at the 0.5 mg L^?1 level) and a limit of detection of 8 μg L^?1 Cu(II) for 10 min of accumulation (at a S/N ratio of 5). The electrode was, finally, applied to the determination of copper in tap‐water, pharmaceutical tablets and bovine serum with recoveries of 97.4, 94.9 and 93.4%, respectively     

Effect of Organic Substances on the Results of Anodic Stripping Voltammetry Detection of Metal Ions in Aqueous Media

Abstract

The d.c. anodic stripping voltammetry method has been used to investigate the effect of organic substances simulating the composition of natural waters on the results of determination of concentration levels of copper, lead and cadmium. The response, sensitivity and concentration (the latter determined by the standard additions method) have been used as sources of information. In the presence of enzymes, fulvic acids, humic acids and polyethylene glycol all these three parameters change in the case of determination of copper and lead, making the results unreliable. The determination of cadmium concentration is not hampered by the said organic substances.     

Iridium Oxide Film Electrodes for Anodic Stripping Voltammetry

The new iridium oxide film electrode, applied for the determination of lead(II), cadmium(II) and copper(II) traces using differential pulse anodic stripping voltammetry (DP ASV) is presented. The electrode display an interesting stripping voltammetric performance which compares with electrodes commonly used in voltammetry. The deposited film is known as anodically electrodeposited iridium oxide film (AEIROF). The AEIROF electrode is characterized by long‐term stability (more than 40 days) and very good reproducibility of the analytical signals in this time (≤12% for 0.5 μM of lead). The regeneration of iridium film is very simple in a time shorter than 60 seconds. The effects of various factors such as: thickness of AEIROF film, preconcentration potential and time, supporting electrolyte composition, potential interferences are optimized. The detection limit for AEIROF film electrode based on glassy carbon for an accumulation time of 30 s is as low as 7 nM for lead(II). The repeatability of the method at a concentration level of the lead(II) as low as 0.5 μM, expressed as RSD is 2.5% (n=10). The proposed method was successfully applied and validated by studying certified reference material CTA‐OTL‐1. Such an attractive use of ‘mercury–free’ ‐ environmentally friendly electrodes offers great promise to measure trace metals.     

基于胶体金标记的阳极溶出伏安免疫分析用于免疫球蛋白G的测定

提出了一种基于胶体金标记的阳极溶出伏安免疫分析方法。免疫反应在聚苯乙烯微孔板中以夹心分析模式进行,通过物理吸附将兔抗人免疫球蛋白G(IgG)抗体固定于微孔板上,与相应抗原IgG发生免疫反应后,再通过夹心模式捕获相应的纳米金标记的羊抗人IgG抗体,然后再与金标羊抗人IgG抗体和金标兔抗羊二抗形成的免疫复合物反应,在微孔板上进一步引入大量的纳米金,将金溶解后,在碳糊电极上用阳极溶出伏安法(ASV)对金离子进行检测,溶出峰电流的大小间接与待分析物IgG的浓度成正比。对免疫分析的一些实验条件进行了优化。阳极溶出峰电流与IgG的对数浓度在1.1~1 143 ng/mL范围内呈良好的线性关系,检出限为1 ng/mL。将该方法应用于人血清中IgG浓度的测定,取得了满意结果。     

Anodic Stripping Voltammetry: An AFM Study of Some Problems and Limitations

The use of anodic stripping voltammetry for quantitative analytical measurements using solid electrodes is addressed in the light of generic limitations arising from i) electrode heterogeneity, ii) electrode morphology, iii) inhibited electrodeposition, and iv) incomplete stripping of deposited metal in the anodic sweep. It is shown, using direct imaging of electrode surfaces via AFM and optical microscopy, that each of the preceding factors may produce significant deviations from ideal electrode behavior. The use of atomic force microscopy to fully characterize any developed ASV procedures is strongly recommended. To ensure reproducible and accurate stripping voltammetry, steps should be taken to minimize the effects discussed.     

Anodic Stripping Voltammetric Determination of Lead in Tap Water at an Ordered Mesoporous Carbon/Nafion Composite film Electrode

A sensitive mercury‐free lead (Pb²⁺) sensor has been proposed based on an ordered mesoporous carbon and Nafion composite film (OMC/Nafion) coated glassy carbon electrode. The analysis of Pb²⁺ using anodic stripping voltammetry (ASV) includes two steps. Pb²⁺ ions are firstly reduced and deposited on the electrode surface in a Pb²⁺ solution (10 mL) during a preconcentration step biased at ?1.0 V, followed by a measurement step by differential pulse voltammetry (DPV) within the potential range of ?0.8 to ?0.3 V (scan rate: 20 mV/s, frequency: 20 Hz, amplitude: 50 mV, pulse width: 50 ms). Linear calibration curve was found to be from 20 nM to 2 μM for Pb²⁺ with a sensitivity of 17.4±1.38 μA/μM after a 5‐min of preconcentration. The detection limit was estimated to be around 4.60±0.12 nM at the signal to noise ratio of 3. Reproducibility (RSD%) was found to be 3.0% for a single sensor with eight measurements and 4.3% for five sensors prepared with identical procedures. The practical application of the proposed lead sensor was verified by determination of trace level of Pb²⁺ in tap water sample.     

Carbon Nanotubes/Ionophore Modified Electrode for Anodic Stripping Determination of Lead

Bifunctional combination of carbon nanotubes and ionophore is introduced for anodic stripping analysis of lead (Pb²⁺). Carbon nanotubes are employed to improve the detection sensitivity due to their excellent electrical conductivity and strong adsorption ability. An ionophore is utilized for its excellent selectivity toward Pb²⁺. The proposed carbon nanotubes/ionophore modified electrode shows improved sensitivity and selectivity for Pb²⁺. Low detection limit (1 nM), wide linear range (5 nM–8 µM) and excellent selectivity over other metal ions (Cd²⁺, Cu²⁺, and Hg²⁺) was obtained. The practical application has been carried out for determination of Pb²⁺ in real water samples.     

Determination of Cd(II) in Some Foodstuffs by Anodic Stripping Pulse Voltammetry (ASPV) using Glassy Carbon Electrode

Abstract

Cadmium in the presence of 0.04 M NaCl as the electrolyte was determined using stripping voltammetry with superimposed constant amplitude pulses of negative polarity (SVPNP) or positive polarity (SVPPP), and differential pulses stripping voltammetry using rotating disc glass carbon electrode (RDGCE). The SVPNP was found to give the greatest sensitivity. The anodic peak was obtained at potential ?850 to ?795 mV due to the oxidation of cadmium to cadmium(II). Linear calibration curves were obtained in the concentration range between 1.5×10^?9–2×10^?10 M. The relative standard deviation is 4.25% at very low concentration of 2×10^?10 M. This method was successfully applied to the determination of cadmium in some foodstuffs (wheat and its products, vegetables) after acid digestion.     

Sensitive Anodic Stripping Voltammetric Copper Ions Determination Performed in Double Deposition and Double Stripping Steps System for Real Water Samples Analysis

The article reports on utilization of double deposition and stripping steps for increasing sensitivity of Cu(II) determination by anodic stripping voltammetry (ASV) at two lead film working electrodes. A significant preconcentration of copper was achieved thanks to utilization of a simple design of four electrodes system that gives possibility to perform one measurement cycle consisting of two deposition and two stripping steps. Due to the fact that deposition step is doubled, the concentration of Pb(II) needed to lead film electrodes formation was significantly reduced as compared to traditional procedures using three electrodes system. The analytical procedure of Cu(II) determination was optimized. The experimental factors: supporting electrolyte's pH and its concentration, lead ions concentration, potential and time of deposition at both working electrodes were studied. The Cu(II) peak current was linearly dependent on its concentration from 5×10^?10 to 2×10^?8 mol L^?1 (deposition time of 270 and 160 s at the first and the second working electrode, respectively). The obtained detection limit for copper ions determination was 2.1×10^?10 mol L^?1. The described procedure was validated by analysis of two water certified reference materials. The described procedure was also utilized for real water sample analysis.     

Coulometric Anodic Stripping Voltammetry of Lead at Copper Column Electrode

A flow coulometric electroanalytical system using a copper column electrode with a copper wire inserted into a Nafion tube was developed to determine Pb(II) content based on anodic stripping voltammetry. The electrolysis efficiency of 5 μM Pb(II) was evaluated to be 100.4±4.5 % (n=5) when the length of the copper wire and flow rate of the Pb(II) solution were 50 cm and 0.1 mL min⁻¹, respectively. The amount of electricity due to the re-oxidation of Pb electrodeposited at the copper column electrode was proportional to the concentration of Pb(II) in the range between 0.1 to 100 μM, and the limit of detection for Pb(II) was 0.8 μM for a deposition time of 15 min. Interference from the presence of Cd(II) could be avoided and the selective determination of Pb(II) was successfully achieved by adjustment of the electrodeposition potential.     

Determination of Trace Tl(I) by Anodic Stripping Voltammetry on Novel Disposable Microfabricated Bismuth‐Film Sensors

This work reports the trace determination of Tl(I) by square‐wave anodic stripping voltammetry (SWASV) on novel microsensors equipped with a bismuth‐film electrode (BiFE). The sensors were fabricated by a multistep microfabrication approach combining sputtering (to deposit the electrode materialm, bismuth‐ and the insulator SiO₂, on the surface of a silicon wafer) and photolithography (to define the geometry of the sensor). The effect of the preconcentration time, the preconcentration potential and the SW stripping parameters were investigated. Using the selected conditions, the 3σ limit of detection was 0.6 µg L^?1 of Tl(I) at a preconcentration time of 240 s and the percent relative standard deviation was 4.3 % at the 10 µg L^?1 level (n=8). In order to eliminate the interference caused by Pb(II) and Cd(II), EDTA was added in the sample solution The method was successfully applied to the determination of Tl(I) in a certified lake water sample. These new sensors exhibit excellent mechanical stability and offer wide scope as mercury‐free disposable sensors for trace metal analysis.     

Sub‐ppt Level Detection of Mercury(II) Based on Anodic Stripping Voltammetry with Prestripping Step at an In Situ Formed Bismuth Film Modified Glassy Carbon Electrode

Sensitive and selective detection of Hg²⁺ in solution is a challenging work. An anodic stripping voltammetry with prestripping step at an in situ formed bismuth film modified glassy carbon electrode was proposed for detection of mercury(II) in solution. This prestripping step was able to decrease the background and improve the signal‐to‐noise ratio and thus enhance the sensitivity. With this method, highly sensitive and selective detection of Hg²⁺ with a ppt‐level detection limit of 0.5 ng L^?1 could be achieved. Moreover, this method provides low interference, rapid and extreme simple and convenience, and hold great promise for in situ Hg²⁺ determination.