Highly hydrophobically modified polyelectrolytes stabilizing macroemulsions: relationship between copolymer structure and emulsion type

The types of emulsions, oil (n-dodecane) in water (O/W) or water in oil (W/O), stabilized with highly hydrophobically grafted linear poly(sodium acrylate)s, were investigated as a function of polymer chemical architecture. Consequently, a large number of macroemulsifiers, covering a wide range of hydrophobicity, were synthesized by changing the degree of grafting (τ), length (n) and type (single- versus twin-tailed) of the hydrophobic moiety. Monovalent salt (NaNO₃) concentration was used as a probe to adjust and hence to estimate the hydrophile-lipophile balance (HLB) of each copolymer. τ, n, type of graft and electrolyte concentration were identified as field parameters to control emulsion type. In general, decreasing either τ or n was found to favor the formation of direct emulsions. Inverse dispersions were preferentially formed with twin-tailed rather than single-tailed copolymers. Moreover, the types of emulsions stabilized with well-balanced polyelectrolytes can be flipped from O/W to W/O with increasing salt concentration. Finally, following the Davies concept, a HLB scale for polymers was created from a comparison with surfactants of nearly identical chemical structure. Received: 15 June 1998 Accepted: 12 August 1998     

Poly(methyl methacrylate) hollow particles by water-in-oil-in-water emulsion polymerization

Poly(methyl methacrylate) particles having hollow structures were produced by water-in-oil-in-water (W/O/W) emulsion polymerization where sorbitan monooleate (Span80) was used as a primary surfactant and sodium laurylsulfate and Glucopen (APG, polypeptide derivative) were used as secondary surfactants. Urethane acrylate having a molecular structure with a hard segment in the molecular backbone, a long soft segment in the middle, and vinyl groups at both ends was employed as a reactive viscosity enhancer. At low concentration of urethane acrylate, only a few particles contained a void in the polymer phase. However, as the concentration of urethane acrylate increased, the number of the particles containing the void increased. This was because urethane acrylate increased the viscosity of the monomer mixture and helped to form the stable W/O/W emulsion droplets, which possibly restricted droplet coalescence during emulsion polymerization. Moreover, at high concentration of urethane acrylate (above 7 wt%), multi-hollow-structured particles were obtained. It is believed that the increase in the lyophilicity of the monomer mixture caused by urethane acrylate led to stronger interfacial activity of the primary surfactant (Span80) and finally resulted in many internal aqueous droplets. Received: 31 July 1998 Accepted: 13 October 1998     

Facile fabrication of snowman-like Janus particles with asymmetric fluorescent properties via seeded emulsion polymerization

This paper presents a facile method for the preparation of snowman-like Janus particles (SJP) with asymmetric fluorescent property via seeded emulsion polymerization, in which in situ formed raspberry-like cadmium sulfide/poly(styrene–divinylbenzene–acrylic acid) nanocomposite particles (RNP) were used as the seeds. The as-prepared RNP and SJP have been thoroughly characterized by transmission electron microscopy, field-emission scanning electron microscopy, thermogravimetric analysis, X-ray powder diffraction, Fourier transform infrared, ultraviolet visible, and photoluminescent spectrometry. It is found that the size ratio of the polymer bulge/inorganic seed part could be continuously tuned as well as the composition of polymer bulges by changing the composition of monomer mixtures and monomer/seed weight ratio. The obtained Janus particles possess amphiphilic properties which can be further used as solid surfactants to stabilize W/O emulsions and successively to construct hierarchical structured materials. Meanwhile, their asymmetric fluorescent properties may be exploited to detect their assembled situation and orientation at the oil–water interface of emulsions as well as at the surface of hierarchical structured materials.

Synthesis of an alkali‐swellable emulsion and its effect on the rate of polymer diffusion in poly(vinyl acetate‐butyl acrylate) latex films

We describe the synthesis and characterization of a weakly cross‐linked poly(methacrylic acid‐co‐ethyl acrylate) alkali‐swellable emulsion (ASE), as well as an investigation of its influence on the rate of polymer diffusion in latex films. The films examined were formed from poly(vinyl acetate‐co‐butyl acrylate) latex particles containing a small amount of acrylic acid as a comonomer. Polymer diffusion rates were monitored by the energy transfer technique. We found that the presence of the ASE component, either in the acid form or fully neutralized by ammonia or sodium hydroxide, had very little effect on the polymer diffusion rate. However, in the presence of 2 wt % NH₄‐ASE, there was a small but significant increase in the polymer diffusion rate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5632–5642, 2005     

PEG-coated reverse osmosis membranes: Desalination properties and fouling resistance

This study focuses on the use of surface-coated reverse osmosis (RO) membranes to reduce membrane fouling in produced water purification. A series of crosslinked PEG-based hydrogels were synthesized using poly(ethylene glycol) diacrylate as the crosslinker and poly(ethylene glycol) acrylate, 2-hydroxyethyl acrylate, or acrylic acid as comonomers. The hydrogels were highly water permeable, with water permeabilities ranging from 10.0 to 17.8 (L μm)/(m² h bar). The hydrogels were applied to a commercial RO membrane (AG brackish water RO membrane from GE Water and Process Technologies). The water flux of coated membranes and a series-resistance model were used to estimate coating thickness; the coatings were approximately 2 μm thick. NaCl rejection for both uncoated and coated membranes was 99.0% or greater, and coating the membranes appeared to increase salt rejection, in contrast to predictions from the series-resistance model. Zeta potential measurements showed a small reduction in the negative charge of coated membranes relative to uncoated RO membranes. Model oil/water emulsions were used to probe membrane fouling. Emulsions were prepared with either a cationic or an anionic surfactant. Surfactant charge played a significant role in membrane fouling even in the absence of oil. A cationic surfactant, dodecyltrimethyl ammonium bromide (DTAB), caused a strong decline in water flux while an anionic surfactant, sodium dodecyl sulfate (SDS), resulted in little or no flux decline. In the presence of DTAB, the AG RO membrane water flux immediately dropped to 30% of its initial value, but in the presence of SDS, its water flux gradually decreased to 74% of its initial value after 24 h. DTAB-fouled membranes had lower salt rejection than membranes not exposed to DTAB. In contrast, SDS-fouled membranes had higher salt rejection than membranes not exposed to SDS, with rejection values increasing, in some cases, from 99.0 to 99.8% or higher. In both surfactant tests, coated membranes exhibited less flux decline than uncoated AG RO membranes. Additionally, coated membranes experienced little fouling in the presence of an oil/water emulsion prepared from DTAB and n-decane. For example, after 24 h the water flux of the AG RO membrane fell to 26% of its initial value, while the water flux of a PEGDA-coated AG RO membrane was 73% of its initial value.     

Copolymer nanosphere encapsulated CdS quantum dots prepared by RAFT copolymerization: synthesis,characterization and mechanism of formation

Cadmium sulfide (CdS) quantum dots (QDs) encapsulated in block copolymer spheres were synthesized by an aqueous emulsion polymerization process. First, stable dispersions of CdS QDs in water were prepared using a polymer dispersant, either poly(acrylic acid) or a random copolymer having an average of ten acrylic acid and five butyl acrylate units. These polymer dispersants were prepared by reversible addition-fragmentation chain transfer polymerization. Then, the CdS QDs dispersed in water were encapsulated in a polystyrene shell using an emulsion polymerization process. Spectroscopic and microscopic techniques were used to characterize the resulting nanocomposites. Optical properties of QDs in polymer microspheres were investigated by UV-vis and fluorescence spectroscopic studies. Particle sizes of all CdS QD samples were calculated from absorption edges using Henglein's empirical curve. Transmission electron microscopy was used to determine the size and morphology of CdS QD samples. These observations were used to elucidate the mechanism of formation of the resulting well-defined polymer-encapsulated CdS nanoparticles.     

SYNTHESIS OF SOAP-FREE ACRYLIC HYDROSOLS

Poly(methyl methacrylate/ethyl acrylate/acrylic acid) hydrosols were prepared by employing soap-freepolymerization, and (acrylic acid/butyl acrylate) oligomer was used as the polymeric surfactant The effect of reactioncondition on the morphology and particle size of the hydrosols was investigated. The minimum amount of acrylic acid in thehydrosols is 2%. The maximum weight average molecular weight (M_w) of polymer that assures soap-free emulsionconversion into hydrosol is about 1.2×10~5-1.3×10~5. The particle transforming process was investigated, and an obviouschange of particle diameter and morphology was observed.     

Synthesis of anionic amphiphilic diblock copolymers of poly(styrene) and poly(acrylic acid) by reverse iodine transfer polymerization (RITP) in solution and emulsion

Reverse iodine transfer polymerization (RITP), offering the appealing potential of the in situ generation of transfer agents out of molecular iodine I₂, is employed in the synthesis of anionic amphiphilic diblock copolymers of poly(styrene) and poly(acrylic acid). Starting with well‐characterized poly(styrene) as macro‐transfer agents synthesized by RITP, diblock copolymers poly(styrene)‐b‐poly(tert‐butyl acrylate) of various lengths are successfully yielded in solution with a good architectural control. These blocks are then subjected to acid deprotection and subsequent pH control to give rise to anionic amphiphilic poly(styrene)‐b‐poly(acrylic acid). Besides, homopolymers of tert‐butyl acrylate are produced by RITP both in solution and in emulsion. Furthermore, a fruitful trial of the synthesis of diblock copolymers poly(tert‐butyl acrylate)‐b‐poly(styrene) is carried out through chain extension of the poly(tert‐butyl acrylate) latex as a macro‐transfer agent in seeded emulsion polymerization of styrene. Finally, the prepared block copolymer is deprotected to bring about its amphiphilic nature and a pH control caters for its anionic character. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4389–4398     

A review of: “Nineteenth Century Attitudes: Men of Science (Chemists and Chemistry Series,Vol. 13)”. Sydney Ross. Kluwer Academic Publishers; Dordrecht, 1991. pp. xi+235. $69.00.

Abstract

The potential of polytetrafluoroethylene (PTFE) membranes as water‐in‐oil (W/O) emulsification devices was investigated to obtain uniformly sized droplets and to convert them into microcapsules and polymer particles via subsequent treatments. Uniform W/O emulsion droplets have not been achieved using glass membranes unless the membrane was rendered hydrophobic by treatment with silanes. If a PTFE membrane is capable of providing uniform droplets for a W/O emulsion, a coordinated membrane emulsification system can be established since glass membranes have been so successful for O/W (oil‐in‐water) emulsification. In order to examine the feasibility of PTFE membrane emulsification, O/W and W/O emulsion characteristics prepared using PTFE membranes were compared with those prepared by the conventional SPG (Shirasu porous glass) membrane emulsification method. A 3 wt.% sodium chloride solution was dispersed in kerosene using a low HLB surfactant. Effects of the membrane pore size, permeation pressure, and the type of emulsifiers and concentration on the droplet size and on the size distribution (CV, coefficient of variation) were investigated. The CV of the droplets was fairly low, and the average droplet size was correlated with the critical permeation pressure of the dispersed phase, revealing that the PTFE membrane could be used as a one‐pass membrane emulsification device. Low CV values were maintained with a Span 85 (HLB = 1.8) concentration, 0.2–5.0 wt.% and a range of HLB from 1.8–5.0. For a brief demonstration of practical applications, nylon‐6,10 microcapsules prepared by interfacial polycondensation and poly(acrylamide) hydrogels from inverse suspension polymerization are illustrated.     

Neutral and Charged Brushes Covalently Grafted from OH-Functionalized Mica Surfaces using Surface-Initiated ATRP – Swelling Investigation by AFM

Poly(acrylic acid) (PAA) and poly(tert-butyl acrylate) (PBA) brushes of various grafting densities were prepared via surface-initiated polymerization of tert-butyl acrylate on mica. PAA was prepared by hydrolyzing the PBA brushes. The swelling behavior of PBA and PAA brushes was studied as a function of grafting density by AFM. The swelling of the polymer layer was found to be higher for PAA in water than for the PBA sample swollen with DFM.     

Influence of metal ions on the alkali-swelling behavior of carboxylated acrylic polymer latexes

The alkalization of carboxylated acrylic polymer latexes by sodium hydroxide gives rise to swelling of the particles. For a poly(n-butyl acrylate) latex copolymerized with 15 wt % methacrylic acid (MAA) and 7 wt % acrylonitrile the particle volume increases by a factor of 30. The alkali-swelling does not depend on the type of monovalent cation used in the base (LiOH, NaOH, KOH, NH₄OH). In contrast, when bivalent cation bases such as Ca(OH)₂ are employed no latex swelling is observed during neutralization because of ionic crosslinking of the copolymer chains. Crosslinking also takes place when the bivalent cations (Ca²⁺, Zn²⁺, Mg²⁺) are added as chlorides to dispersions with latexes previously swollen by sodium hydroxide. In these experiments the original size of the latexes is reached again at a molar ratio MAA: bivalent metal ion of 2:1, i.e. at charge compensation of the carboxyl groups. The shrinking behavior is almost independent of the type of bivalent metal ion used. On the other hand, it is more pronounced when trivalent cations such as Fe³⁺ are added. In general, the experiments demonstrate that the alkali swelling of acrylic latexes is dominated by electrostatic forces. Received: 18 August 1998 Accepted in revised form: 26 October 1998     

Gold nanoparticle synthesis in graft copolymer micelles

 An amphiphilic poly(acrylic acid)/polystyrene graft copolymer (PAA-g-PS) has been used to form “nanoreactors” for the synthesis of gold clusters. Such copolymers tend to form stable micelles in non-polar organic solvents where the poly(acrylic acid) chains constitute the core, and the polystyrene chains, the shell. In the present study, the micellar structure of PAA-g-PS in toluene has been demonstrated by dynamic light scattering and transmission electron microscopy (TEM). The subsequent preparation of gold-graft copolymer composites involved the introduction of gold chloride (AuCl₃), either in powder form or previously dissolved in ether, into the micellar cores of the PAA-g-PS in toluene. The gold salt was then reduced by ultraviolet (UV) irradiation of the emulsion, or of dried cast films. TEM and ultraviolet-visible (UV/Vis) spectroscopy were used to characterize the resulting composites. Gold particles of less than 5 nm in diameter were observed in all cases, but the size distribution and the spatial arrangement of the clusters in the cast films were modified when diethyl ether was used to introduce AuCl₃ into the PAA-g-PS micellar cores. This was thought to be due to enhanced nucleation of the gold particles and partial disruption of the micellar cores in the presence of diethyl ether. Received: 21 January 1998 Accepted: 11 June 1998     

Synthesis and characterization of lower generation broom molecules

Dendritic molecules with dodecyl groups as the hyperbranchs were synthesized in methanol by Michael addition with dodecylamine and methyl acrylate as raw materials. This new-type dendritic molecules were called vividly ＂broom molecules＂ in this report. The surface tension of the aqueous solution of broom molecule terminated amino group was measured by using the dropvolume method. The demulsification performance of the broom molecules for the oil/water （O/W） simulated crude oil emulsion was examined. The experimental results revealed that, as a new-type of surfactants, the broom molecules terminated amino groups showed demulsification for the O/W simulated crude oil emulsion. 2007 Jun Wang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All fights reserved.     

Supramolecular polymer gels formed from polyamidine and random copolymer of n-butyl acrylate and acrylic acid

We have prepared the amidinium-carboxylate salt bridge-based supramolecular polymer gels from random copolymer of n-butyl acrylate and acrylic acid and a linear polyamidine having N,N′-di-substituted acetamidine group in the main chain. The supramolecular polymer gel with equimolar amounts of carboxy and amidine groups shows a high G′ value of 1.6 MPa at 25°C. In contrast, the gel prepared from the carboxy polymer and linear polyethyleneimine instead of the polyamidine shows liquid-like fluidity with a G′ value of 0.01 MPa at 25°C. The robustness of the amidine-based supramolecular polymer gels is attributed to the high stability of the amidinium-carboxylate salt bridge. Replacing the random copolymer with carboxy-terminated telechelic poly(n-butyl acrylate) results in a significant decrease in G′ as well as |η*|, which may arise from the difference in the network structure due to the arrangement of carboxy groups.     

Preparation of porous/hollow particles of phenolic resin

Porous/hollow polymer microparticles were prepared by suspension polymerization from a resol, water‐soluble phenolic resin in a multiple emulsion system oil‐in‐water‐in‐oil(O/W/O). The porous/hollow structures of phenolic resin microparticle were characterized by optical microscopy (OM) and scanning electron microscopy (SEM). It is shown that the porous/hollow structure is related to a dispersion and curing process of the resol resin. It was indicated that it is low‐cost and simple to prepare porous/hollow phenolic resin micr‐particles from resol in an O/W/O system. Copyright © 2007 John Wiley & Sons, Ltd.     

Efficient water‐soluble drag reducing star polymers with improved mechanical stability

We describe here the first example of the synthesis of 4‐arm star poly(acrylic acid) for use as a water‐soluble drag reducing agent, by applying Cu(0)‐mediated polymerization technique. High molecular weight 4‐arm star poly(tert‐butyl acrylate) (M_n = 3.0–9.0 × 10⁵ g mol^?1) was first synthesized using 4,4′‐oxybis(3,3‐bis(2‐bromopropionate)butane as an initiator and a simple Cu(0)/TREN catalyst system. Then, 4‐arm star poly(tert‐butyl acrylate) were subjected to hydrolysis using trifluoroacetic acid resulting in water‐soluble 4‐arm star poly(acrylic acid). Drag reduction test rig analysis showed 4‐arm star poly(acrylic acid) to be effective as a drag reducing agent with drag reduction of 24.3%. Moreover, 4‐arm star poly(acrylic acid) exhibited superior mechanical stability when compared with a linear poly(acrylic acid) and commercially available drag reducing polymers; Praestol and poly(ethylene oxide). The linear poly(acrylic acid), Praestol, and poly(ethylene oxide) all showed a large decrease in drag reduction of 8–12% when cycled 30 times through the drag reduction test rig while, in contrast, 4‐arm star poly(acrylic acid) demonstrated much higher mechanical stability. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 335–344     

Low-rate dynamic contact angles on poly(n-butyl methacrylate) and the determination of solid surface tensions

 Low-rate dynamic contact angles of 22 liquids on a poly(n-butyl methacrylate) (PnBMA) polymer are measured by an automated axisymmetric drop shape analysis-profile (ADSA-P). It is found that 16 liquids yielded non-constant contact angles, and/or dissolved the polymer on contact. From the experimental contact angles of the remaining 6 liquids, it is found that the liquid–vapor surface tension times cosine of the contact angle changes smoothly with the liquid–vapor surface tension, i.e. γ_lv cos θ depends only on γ_lv for a given solid surface (or solid surface tension). This contact angle pattern is in harmony with those from other inert and non-inert (polar and non-polar) surfaces [34–37, 45–47]. The solid–vapor surface tension calculated from the equation-of-state approach for solid-liquid interfacial tensions [14] is found to be 28.8 mJ/m², with a 95% confidence limit of ±0.5 mJ/m², from the experimental contact angles of the 6 liquids. Received: 12 September 1997 Accepted: 22 January 1998     

Aqueous solution behavior of alkali-soluble polyethylene periodic polyelectrolyte, poly(ethylene- per-ethylene-per-acrylic acid)

A sequence-ordered, periodic copolymer of ethylene, ethylene, and acrylic acid, poly (ethylene-per-ethylene-per-acrylic acid) (PEEA), with M _w=1.44×10⁵ has been synthesized by alternating copolymerization of 1,3-butadiene and methyl acrylate, followed by hydrogenation and hydrolysis. Aqueous solution and dissociation properties of the alkali-soluble PEEA were explored by potentiometric titration and intrinsic viscosity at 25 °C. The pH values of PEEA were almost constant (pH = 6.48 ∼ 6.55) with an increasing degree of dissociation (α) from 0.3 to 0.8 at C _s=50 mN NaCl. Correspondingly, the plots of negative logarithm of apparent dissociation constant (pK _a) against α showed a reversed S-shape curve over the whole α, indicating an extensive precipitation and subsequent tran-sition from compact to coiled conformation. The intrinsic viscosity steeply increased with α above 0.4 up to 9.97 dl/g at α = 1.0. Good agreement between the observed electrostatic potential and that calculated from the rod model with a smeared charge density was observed in the region of α higher than 0.9. The dissociation and dissolution processes of PEEA with neutralization in water were described. Received: 14 April 1998 Accepted: 3 June 1998     

Liquid chromatography of polymer mixtures applying a combination of exclusion and full adsorption mechanisms. 5. Six-component blends of chemically similar polymers

The separation of six-component blends of chemically similar homopolymers utilising the full adsorption-desorption (FAD) process is presented. The main advantage of the FAD approach over other methods represents the successive and independent size- exclusion chromatography (SEC) characterisation of all blend components. The method is based on the full adsorption and retention of all n or n−1 components of the polymer blend from an adsorption promoting liquid (ADSORLI) in a small FAD column. Nonadsorbed macromolecules are forwarded directly into SEC for molecular characterisation. Next, appropriate displacers are successively applied to the FAD column to selectively release preadsorbed blend constituents into the on-line SEC column. Dynamic integral desorption isotherms for single constituents, as well as for polymer blends to be analysed, allow identification of optimal displacer compositions to release just one kind of macromolecule. Model polymer blends containing polystyrene (PS), poly(lauryl methacrylate), poly(butyl methacrylate), poly(ethyl methacrylate), poly(methyl methacrylate) and poly(ethylene oxide) (PEO) or, alternatively, PS, poly(2-ethylhexyl acrylate), poly(butyl acrylate), poly(ethyl acrylate), poly(methyl acrylate) and PEO of similar molar masses can be separated and characterised in one multistep run using nonporous silica FAD packing, toluene as an ADSORLI and its mixtures with a desorption promoting liquid such as ethyl acetate, tetrahydrofuran or dimetylformamide to form displacers with appropriate desorption strength. Received: 9 September 1998 Accepted in revised form: 16 November 1998     

A novel synthesis of acrylic acid containing polymers

A novel synthesis of linear acrylic acid containing polymers, poly(styrene-co-acrylic acid) and poly(acrylic acid), was accomplished through hydrolysis of the respective parent polymers, i.e. poly(styrene-co-methyl acrylate) and poly(methyl acrylate), with trimethylsilyl iodide under mild conditions. Combination of ¹H NMR, ¹³C NMR, FTIR, DSC and chemical titration confirms that the conversion from methoxycarbonyl to carboxyl is almost complete. This method is further successfully applied to synthesize poly-(ethyl methacrylate-co-acrylic acid) through selective hydrolysis of the methyl acrylate units in poly(ethyl methacrylate-co-methyl acrylate).