Extensive enhancement in power conversion efficiency of dye-sensitized solar cell by using Al-doped TiO<Subscript>2</Subscript> photoanode

In this work, we have prepared Al-doped TiO₂ nanoparticles via a hydrothermal method and used it for making photoanode in dye-sensitized solar cell (DSSC). Material characterizations were done using XRD, AFM, SEM, TEM and EDAX. XPS results reveal that Al is introduced successfully into the structure of TiO₂ creating new impurity energy levels in the forbidden gap. This resulted in tuning of the conduction band of TiO₂ and reduced charge recombination which led to better current conversion efficiency of DSSC. Greater dye loading and enhanced surface area was obtained for Al-doped TiO₂ compared to un-doped TiO₂. I-V analysis, EIS and Bode plots are employed to evaluate photovoltaic performance. The short-circuit current density (J _sc) and efficiency (η) of cell employing Al-doped TiO₂ photoanode were extensively enhanced compared to the cell using un-doped TiO₂. The optical band gap (E _g) for Al-doped and un-doped TiO₂ was obtained as 2.8 and 3.2 eV, respectively. J _sc and η were 13.39 mAcm^?2 and 4.27%, respectively, under illumination of 100 mWcm^?2 light intensity when thin films of 1% Al-doped TiO₂ was employed as photoanode in DSSC using N719 as the sensitizer dye. With the use of un-doped TiO₂ as photoanode under similar conditions, J _sc 5.12 mAcm^?2 and η 1.06% only could be obtained. The maximum IPCE% obtained with Al-doped TiO₂ and un-doped TiO₂ was 67 and 38% respectively at the characteristic wavelength of dye (λ _max = 540 nm). The EIS analyses revealed resistive and capacitive elements that provided an insight into various interfacial processes in terms of the charge transport. It was observed that Al-doping reduced the interfacial resistance leading to better charge transport which has improved both photocurrent density and conversion efficiency. Higher electron mobility and fast diffusion resulting in greater charge collection efficiency was obtained for Al-doped TiO₂ compared to the un-doped TiO₂. Using the Mott–Schottky plot, the donor density was calculated for un-doped and Al-doped TiO₂. The work demonstrated that the Al-doped TiO₂ is potential photoanode material for low-cost and high-efficiency DSSC.     

An efficient method to prepare high-performance dye-sensitized photoelectrodes using ordered TiO<Subscript>2</Subscript> nanotube arrays and TiO<Subscript>2</Subscript> quantum dot blocking layers

High-performance dye-sensitized photoelectrodes using ordered TiO₂ nanotube arrays (TNTs) and TiO₂ quantum dot blocking layers are fabricated. The free-standing TNT membranes with perfect ordered morphology are prepared by three times of anodic oxidation on Ti foils. These TNT membranes can be easily transported to conductive glasses to fabricate front-side illuminated photoelectrodes. By changing anodic oxidation duration, the thickness of TNT membranes can be controlled, which shows significant influence on the UV-Vis reflectance and absorption abilities of TNT-based photoelectrodes and further influence photovoltaic performance of dye-sensitized solar cells (DSSCs). The highest power conversion efficiency (PCE) of DSSCs about 6.21 % can be obtained by using TNT membranes prepared with anodic oxidation of 3 h. For further improving photovoltaic performance of DSSCs, TiO₂ quantum dot (QDs) blocking layers are inserted between conductive glasses and TNT membranes in the photoelectrodes, which show remarkable effects. The highest PCE of DSSCs with this kind of blocking layers can increase to 8.43 %, producing 35.75 % enhancement compared with that of the counterparts without TiO₂ QD blocking layers.     

Photovoltaic properties of oriented ZnO nanowires arrays decorated with TiO<Subscript>2</Subscript> shell layer for dye-sensitized solar cell application

Almost vertically aligned ZnO nanowires have been grown on Silicon substrates via a simple hydrothermal method. In order to improve the photoelectric conversion efficiency for fabricated dye-sensitized solar cells (DSSCs), an easily-operated immersing method was employed to fabricate a TiO₂/ZnO nanowires array heterojunction, which has advantage of high aspect ratio, low recombination rate and high absorption of visible light. The structure and surface morphology of the samples were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM), respectively. The photovoltaic properties of TiO₂/ZnO based DSCCs were measured by considering the power efficiency (η), photocurrent density (J_sc), open-circuit voltage (V_oc), and fill factor (FF). An efficiency of 0.559% is achieved for the composite cell, increasing 0.426 and 0.185% for the ZnO nanowires cell and TiO₂ cell, respectively. The short-circuit current and open-circuit voltage are also enhancing. The improvements are because of high surface are of TiO₂ shell layer, as well as fast electron transport and light scattering effect of ZnO nanowires.     

Extensional rheology of cellulose/NaOH/urea/H<Subscript>2</Subscript>O solutions

The extensional flow behaviors of cellulose/NaOH/urea/H₂O solution were investigated by using capillary breakup extensional rheometry (CaBER). The effects of temperature, storage time and cellulose concentrations on both the storage modulus G′ and the loss modulus G″ were also analyzed. For 2 wt% cellulose solution, the G′, G″ and filament lifetime remained unchanged after long storage time. While, for 4 wt% cellulose solution, physical gels could form at either higher temperature or for longer storage time, and the filament lifetime, the relaxation time (λ _e ) and the initial extensional viscosity (η _e0) first increased and then decreased with increase of the storage time. The transition points of the filament lifetime shifted to lower storage time with the increase of the temperature. The η _e0 is proportional to λ _e . The results presented suggest that the extensional properties of the cellulose/NaOH/urea/H₂O solution first increase and then decrease during the gelation process, and the spinning time, which decreases linearly with the increase in the storage temperature, must be controlled below the time that η _e0 starts to decrease.     

Synthesis and characterization of a new monophosphate (C<Subscript>6</Subscript>H<Subscript>16</Subscript>N<Subscript>2</Subscript>)(H<Subscript>2</Subscript>PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

Chemical preparation, crystal structure, and NMR spectroscopy of a new trans-2,5-dimethylpiperazinium monophosphate are given. This new compound crystallizes in the triclinic system, with the space group P-1 and the following parameters: a = 6.5033(3), b = 7.6942(4), c = 8.1473(5) Å, α = 114.997(3), β = 92.341(3), γ = 113.136(3), V = 329.14(3) ų, Z = 1, and D_x = 1.565 g cm^?3. The crystal structure has been determined and refined to R = 0.030 and R _w(F ²) = 0.032 using 1558 independent reflections. The structure can be described as infinite [H₂PO₄] _n ^n? chains with (C₆H₁₆N₂)²⁺ organic cations anchored between adjacent polyanions to form columns of anions and cations running along the b axis. This compound has also been investigated by IR, thermal, and solid-state, ¹³C and ³¹P MAS NMR spectroscopies and Ab initio calculations.     

Poly(Styrene Sulfonate)/Poly(Allylamine Hydrochloride) Encapsulation of TiO<Subscript>2</Subscript> Nanoparticles Boosts Their Toxic and Repellent Activity Against Zika Virus Mosquito Vectors

Green fabricated nanoparticles often need to be encapsulated and stabilized, to ensure uniform dispersion in the aquatic environment and relevant larvicidal activity over time. However, recent research showed that nanoencapsulation processes led to a reduction of nanoparticle larvicidal efficacy. We used an extract of Argemone mexicana to reduce TiO₂ nanoparticles, which were then capped with PSS/PAH (poly(styrene sulfonate)/poly(allylamine hydrochloride)). The toxic and repellent potential of the nanoparticles were compared to elucidate their potential effects against the Zika virus vector Aedes aegypti. Nanoparticles were characterized by biophysical methods including UV–Vis, EDX and FTIR spectroscopy, SEM, TEM, XRD and DLS analyses. In larvicidal and pupicidal experiments, TiO₂ nanoparticles achieved LC₉₀ values from 41.648 (larva I), to 71.74 ppm (pupa). Nanoencapsulated TiO₂ achieved LC₉₀ values from 39.16 (I), to 69.12 ppm (pupa). In adulticidal experiments, LC₉₀ of TiO₂ nanoparticles on Ae. aegypti was 10.31 ppm, while LC₉₀ of nanoencapsulated TiO₂ was 9.54 ppm. At 10 ppm, the repellency towards Ae. aegypti was 80.43% for TiO₂ nanoparticles, and 88.04% for nanoencapsulated TiO₂. This research firstly highlighted the promising potential of PSS/PAH encapsulation, leading to the production of highly effective titania nanostructures, if compared to titania nanoparticles synthesized with eco-friendly routes without further stabilization.     

Synthesis of new dyes containing double tetrazole groups for sensitization of TiO<Subscript>2</Subscript> nanoparticles in dye-sensitized solar cells

Di(1H-tetrazol-5-yl)methane is employed as a new electron acceptor group in the synthesis of two metal-free organic dyes containing triphenylamine donor group. Dye-sensitized nanocrystalline TiO₂ solar cell (DSSC) applying these novel dyes is constructed for consideration of their photovoltaic properties. The electronic properties of the dyes are also considered with the aid of theoretical calculations. The DSSC constructed from 4-(2,2-di(1H-tetrazol-5-yl)vinyl)-N,N-diphenylaniline (T1) shows a short-circuit photocurrent density of 13.38 mA cm^?2, an open circuit voltage of 578 mV, and a fill factor of 0.54, with a resulted solar energy-to-electricity conversion efficiency of 4.18% under simulated 1 sun irradiation (100 mW cm^?2). This result reveals that the dye with the di(1H-tetrazol-5-yl)methane anchoring group injects more electrons to the conduction band of TiO₂ in comparison with its analogs with single tetrazole ring in their anchoring group. It is found that in spite of a red-shift of the absorption spectrum resulted from the lengthening of the molecule, the dye with two di(1H-tetrazol-5-yl)methane groups gives lower performance than the dye with a single electron acceptor.     

<Emphasis Type="Italic">cis</Emphasis>-Dioxomolybdenum(VI) complexes of sterically encumbered phenol-based tetradentate N<Subscript>2</Subscript>O<Subscript>2</Subscript> ligands: Structural,spectroscopic, and electrochemical studies

Two cis-dioxomolybdenum(VI) complexes [MoO₂L] (L: L ¹, 2 and L: L ², 3) in a phenol-based sterically encumbered N₂O₂ ligand environment have been synthesized, and their crystallographic characterizations are reported. The orange crystals of 2 are monoclinic, space group P2₁/a with unit cell dimensions as a=16.2407(17) Å, b=7.2857(8) Å, c=18.400(2) Å, β=98.002(9)°, Z=4, and d _cal=1.486 g cm^?3. The light orange crystals of 3, however, are orthorhombic, space group, Pbcn, with unit cell dimensions a=8.3110(12) Å, b=12.637(3) Å, c=34.673(5) Å, Z=4, and d _cal=1.187 g cm^?3. The structures were refined by a full-matrix least-squares procedure on F ² to a final R=0.046 (0.055 for 3) using 4944 (3677) all independent data. In both the cases, the Mo atom exists in a distorted octahedral geometry defined by a N₂O₄ donor set, which features a cis-Mo(–O)₂ and a trans-Mo(OPh)₂ arrangement. Compound 2 undergoes a quasireversible one-electron reduction at ?1.3 V vs Ag/AgCl reference due to Mo^VIO₂/Mo^VO₂ electron transfer and thus providing a rare example of steric solution to the comproportionation–dimerization problem encountered frequently in the development of valid biomimetic models for the active sites of oxomolybdenum enzymes.     

Thermal properties,phase transitions,vibrational and reorientational dynamics of [Mn(NH<Subscript>3</Subscript>)<Subscript>6</Subscript>](NO<Subscript>3</Subscript>)<Subscript>2</Subscript>

[Mn(NH₃)₆](NO₃)₂ crystallizes in the cubic, fluorite (C1) type crystal lattice structure (Fm \( \overline{3} \) m) with a = 11.0056 Å and Z = 4. Two phase transitions of the first-order type were detected. The first registered on DSC curves as a large anomaly at T _C1 ^h  = 207.8 K and T _C1 ^c  = 207.2 K, and the second registered as a smaller anomaly at T _C2 ^h  = 184.4 K and T _C2 ^c  = 160.8 K (where the upper indexes h and c denote heating and cooling of the sample, respectively). The temperature dependence of the full width at half maximum of the band associated with the δ_s(HNH)F_1u mode suggests that the NH₃ ligands in the high temperature and intermediate phase reorientate quickly with correlation times in the order of several picoseconds and with activation energy of 9.9 kJ mol^?1. In the phase transition at T _C2 ^c probably only a some of the NH₃ ligands stop their reorientation, while the remainders continue to reorientate quickly with activation energy of 7.7 kJ mol^?1. Thermal decomposition of the investigated compound starts at 305 K and continues up to 525 K in four main stages (I–IV). In stage I, ²/₆ of all NH₃ ligands were seceded. Stages II and III are connected with an abruption of the next ²/₆ and ¹/₆ of total NH₃, respectively, and [Mn(NH₃)](NO₃)₂ is formed. The last molecule of NH₃ per formula unit is freed at stage IV together with the simultaneous thermal decomposition of the resulting Mn(NO₃)₂ leading to the formation of gaseous products (O₂, H₂O, N₂ and nitrogen oxides) and solid MnO₂.     

Study of quasi-solid electrolyte in dye-sensitized solar cells using surfactant as pore-forming materials in TiO<Subscript>2</Subscript> photoelectrodes

A novel polymer gel electrolyte was used to improve the performance and long-term stability in dye-sensitized solar cells (DSSCs). The polymer gel electrolyte (PGE) was prepared by mixing 5 wt% poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and 2 % TiO₂ nanoparticles. The conductivity of PGE with P25 reached 9.98 × 10^?3 S/cm, which increased by 34.9 % compared with 7.40 × 10^?3 S/cm of PGE without P25, and the diffusion coefficient was also increased by 19.0 %. Different photoelectrodes were obtained by using three kinds of surfactants (cetylamine, octadecylamine, and P123) as pore-forming materials, and their morphologies were contrasted through scanning electron microscopy (SEM). The results showed that gel electrolyte can increase the short-circuit current density (J _sc) from 11.01 to 12.99 mA/cm² in DSSCs. Moreover, unlike the liquid electrolyte, the gel electrolyte is more conducive to the TiO₂ photoelectrodes with larger pores. In conclusion, the efficiency of DSSC with gel electrolyte and P123 as pore-forming material was 6.73 %, which was 12 % higher than the liquid electrolyte in the same test condition. In addition, the sealed gel electrolyte DSSCs showed better stability than did liquid electrolyte DSSCs during nearly 600 h.     

Synthesis,structural, and electrochemical properties of NaCo(PO<Subscript>3</Subscript>)<Subscript>3</Subscript> cathode for sodium-ion batteries

A new Co-base sodium metaphosphate compound, NaCo(PO₃)₃, has been synthesized here by solid-state method. The crystal structure is refined by the Rietveld method, and the results reveal that NaCo(PO₃)₃ has an orthorhombic structure with the space group of P2 ₁ 2 ₁ 2 ₁ and lattice parameters of a = 14.2453(2) Å, b = 14.2306(1) Å, and c = 14.2603(2) Å. Its typical morphology and chemical composition are confirmed by scanning electron microscopy (SEM) and energy-dispersive spectrometry (EDS). The valence states of all elements and the internal/external vibrational modes of NaCoP₃O₉ compound are measured by X-ray photoelectron and vibrational spectrum, where a typical feature of the (PO₃)^? polyanion group is observed. Meanwhile, the electrochemical properties of NaCo(PO₃)₃ cathode for sodium-ion batteries are also elevated and an initial discharge capacity of 33.8 mAh/g can be obtained at 0.05 C within 1.5–4.2 V. After 20 cycles, a discharge capacity of 26.7 mAh/g can be obtained and a well-kept oxidation–reduction plateau is still observed for NaCo(PO₃)₃ cathode, indicating the good reversibility of this metaphosphate electrode.     

Molecular mechanism of propane oxidative dehydrogenation on surface oxygen radical sites of VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/TiO<Subscript>2</Subscript> catalysts

Minimum energy pathways of propane oxidative dehydrogenation to propene and propanol on supported vanadium oxide catalyst VO _x /TiO₂ were studied by periodic discrete Fourier transform (DFT) using a surface oxygen radical as the active site. The propene formation pathway was shown to consist of two consecutive hydrogen abstraction steps. The first step includes C_β–H bond activation of propane followed by the formation of a surface hydroxyl group V–O _t H and a propyl radical n-C₃H₇. This step with the activation energy E* = 0.56 eV (54.1 kJ/mol) appears to be rate-determining. The second step involves the reaction of the bridging O _b oxygen atom with the methylene C–H bond of propyl radical n-C₃H₇ followed by the formation of a hydroxylated surface site HO _t –V⁴⁺–O _b H and propene. The initial steps of the C–H bond activation during propane conversion to propanol and propene by ODH on V⁵⁺–(O _t O _b )^? active sites are identical. The obtained results demonstrate that participation of surface oxygen radicals as the active sites of propane ODH makes it possible to explain relatively low activation energies observed for this reaction on the most active catalysts. The presence of very active radical species in low concentration seems to be the key factor for obtaining high selectivity.     

Study of variation in thermophysical properties of RE<Subscript>6</Subscript>UO<Subscript>12</Subscript>(s) along the lanthanide series

The novel ligand N,N,N′′′′,N′′′′-tetrabutyl-N′′′,N′′′-(N″,N″-diethyl)-ethidene bisdiglycolamide (TBEE-BisDGA) and other eight analogous extractants have been synthesized and characterized by NMR and HRMS. The solvent extraction of Th⁴⁺, UO₂ ²⁺ and Eu³⁺ from nitric acid solution using the above BisDGA extractants was investigated in 1-dodecanol at 30 ± 1 °C. The extractants exhibited higher affinity toward Th⁴⁺ than UO₂ ²⁺ and Eu³⁺ in the present system. The maximum value of separation factor SF _Th(IV)/U(VI) and SF _{Th(IV)/Eu(III)} is 78.5 and 53.3 respectively for TBEE-BisDGA, 88.1 and 69.5 respectively in the case of TB ^i-PE-BisDGA at 3 M HNO₃ solution.     

The thermodynamic properties of the [(Me<Subscript>3</Subscript>Si)<Subscript>7</Subscript>C<Subscript>60</Subscript>]<Subscript>2</Subscript> fullerene complex

The temperature dependence of the heat capacity C _p ^o of the [(Me₃Si)₇C₆₀]₂ fullerene complex was measured for the first time using precision adiabatic vacuum calorimetry over the temperature range 6.7–340 K and high-accuracy differential scanning calorimetry at 320–635 K. For the most part, the error in the C _p ^o values was about ±0.5%. An irreversible endothermic effect caused by the splitting of the dimeric bond between fullerene fragments and the thermal decomposition of the complex was observed at 448–570 K. The thermodynamic characteristics of this transformation were calculated and analyzed. Multifractal analysis of the low-temperature (T < 50 K) heat capacity was performed, and conclusions were drawn concerning the character of the heterodynamicity of the structure. The experimental data obtained were used to calculate the standard thermodynamic functions C _p ^o (T), H ^o (T) ? H ^o (0), S ^o (T) ? S ^o (0), and G ^o (T) ? H ^o (0) over the temperature range from T → 0 to 445 K and estimate the standard entropy of formation of the compound from simple substances at 298.15 K. The standard thermodynamic properties of [(Me₃Si)₇C₆₀]₂ are compared with those of the (C₆₀)₂ dimer, the [(η⁶-Ph₂)₂Cr]⁺[C₆₀]^?? fulleride, and the initial C₆₀ fullerene.     

Fabrication and characterisation of a mixed oxide-covered mesh electrode composed of NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> and its capability of generating hydroxyl radicals during the oxygen evolution reaction in electrolyte-free water

A mixed oxide-covered mesh electrode composed of NiCo₂O₄ (MOME-NiCo₂O₄) was prepared on a stainless-steel substrate using thermal decomposition (slow-cooling rate method). Surface, bulk and electrochemical properties of MOME were studied using different techniques, namely scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry (CV) with determination of the electrochemical porosity (?) and morphology factor (φ) parameters, quasi-stationary polarisation curves (PC) and electrochemical impedance spectroscopy (EIS). SEM images revealed a good coverage of the metallic wires by a compact oxide layer (absence of cracks). XRD analysis confirmed the formation of the spinel NiCo₂O₄ with the presence of NiO. The ‘in situ’ surface parameters denoted as ? and φ exhibited values of 0.39 and 0.33, respectively, revealing that the electrochemically active surface area is mainly confined to the ‘outer/external’ surface regions of the oxide layer. The PC was characterised by two Tafel slopes distributed in the low (b ₁ = 46 mV dec^?1) and high (b ₂ = 59 mV dec^?1) overpotential domains. The corresponding apparent exchange current densities were j ₀₍₁₎ = (3.43 ± 0.11) × 10^?6 A cm^?2 and j ₀₍₂₎ = (6.70 ± 0.08) × 10^?6 A cm^?2, respectively. The EIS study accomplished in the low-overpotential domain revealed a Tafel slope (b ₁) of 51 mV dec^?1. According to the spin-trapping reaction using N,N-dimethyl-p-nitrosoaniline (RNO), the MOME-NiCo₂O₄ electrode exhibited good performance for the generation of weakly adsorbed hydroxyl radicals (HO^?) during the OER in electrolyte-free water.     

Thermal analysis on C<Subscript>6</Subscript>H<Subscript>10</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript>-doped MgB<Subscript>2</Subscript>

Additives to MgB₂ can improve the superconducting functional characteristics, such as critical current density (J _c) and irreversibility field (H _irr). Recently, we have shown that repagermanium (C₆H₁₀Ge₂O₇) is an effective additive, enhancing both J _c and H _irr. To look into details of the processes taking place during the reactive sintering, a thermal analysis study (0.167 K s^?1, in Ar) is reported. We used differential scanning calorimetry between 298 and 863 K and simultaneous thermogravimetric—differential thermal analysis between 298 and 1233 K. Samples were mixtures of powders with composition 97 mol% MgB₂ and 3 mol% C₆H₁₀Ge₂O₇. Up to 863 K, repagermanium decomposes by multiple steps and forms amorphous phases. A reaction with MgB₂ is not observed. Above this temperature, partial decomposition of MgB₂ occurs. Crystalline Ge and MgO are detected before formation of Mg₂Ge and MgB₄, when temperature approaches the melting point of Ge (1211 K). Carbon substitution for boron in the crystal lattice of MgB₂ is observed for samples heated above 863 K. The amount of substitutional C does not significantly change with temperature.     

Highly efficient mesoporous WO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/KIT-6 catalysts for oxidative desulfurization of dibenzothiophene with hydrogen peroxide

Oxidative desulfurization (ODS) of organic compounds containing sulfur element from a model oil was performed using tungsten oxide catalysts supported on mesoporous silica with cubic Ia3d mesostructure, well-defined mesopores (7.2 nm), high surface area (719 m²/g), and three-dimensional pore network (WO _x /KIT-6). The prepared WO _x /KIT-6 catalysts (5–20 wt% WO _x ) were characterized by X-ray diffraction analysis, N₂ sorption measurements, electron microscopy, H₂-temperature programmed reduction, Raman spectroscopy, and thermogravimetric analysis. Among the mesoporous catalysts, 10 wt% WO _x /KIT-6 exhibited the best catalytic performance. Sulfur-containing organic compounds, such as dibenzothiophene, 4,6-dimethyldibenzothiophene, and benzothiophene, were completely (100 %) removed from the model oil over 10 wt% WO _x /KIT-6 catalyst in 2 h. In addition, the catalyst could be reused several times with only slight decrease in catalytic activity.     

Crystal structure of KPb<Subscript>2</Subscript>Cl<Subscript>5</Subscript> and KPb<Subscript>2</Subscript>Br<Subscript>5</Subscript>

The KPb₂Cl₅ and KPb₂Br₅ crystals are monoclinic (P2₁/c) with a microtwinned structure. X-ray analysis of chloride resulted in the parameters a = 8.854(2) Å, b = 7.927(2) Å, c = 12.485(3) Å; β = 90.05(3)°, d_calc = 4.78(1) g/cm³ (STOE STADI4, MoK_α, 2θ_max = 80°), R₁ = 0.0702 for 4094 F ≥ 4 σ(F) reflections. For bromide, a = 9.256(2) Å, b = 8.365(2) Å, c = 13.025(3) Å; β = 90.00(3)°, d_calc = 5.62(1) g/cm³ (Bruker P4, MoK_α, 2θ_max = 70°), R₁ = 0.0692 for 3076 F ≥ 4 (F) reflections.     

Supramolecular 2D structure of [Co(2-Me-Pyz)<Subscript>2</Subscript>(H<Subscript>2</Subscript>O)<Subscript>4</Subscript>](NO<Subscript>3</Subscript>)<Subscript>2</Subscript>

The complex [Co(2-Me-Pyz)₂(H₂O)₄](NO₃)₂ is synthesized and its structure is determined. The crystals are monoclinic: space group P2₁/n, a = 10.685(2) Å, b = 6.837(1), c = 12.515(3) Å, β = 91.84(3)°, V = 913.8(3) ų, ρ_calcd = 1.042 g/cm ³, Z = 2. The Co²⁺ ion (in the inversion center) is coordinated at the vertices of the distorted octahedron by two nitrogen atoms of methylpyrazine and four oxygen atoms of the water molecules (Co(1)–N(1) 2.180(3), average Co(1)–O(w) 2.079(3) Å, angles at the Co atom 87.9(1)–92.1(1)°). Supramolecular pseudometallocycles are formed in the structure through the O(w)–H…N(1) hydrogen bonds between the coordinated H₂O molecules and the terminal nitrogen atoms of the 2-methylpyrazine molecules. Their interaction results in the formation of supramolecular layers joined by the NO₃ groups into a three-dimensional framework.     

Mechanistic study of Ce-modified MnO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/TiO<Subscript>2</Subscript> catalysts with high NH<Subscript>3</Subscript>-SCR performance and SO<Subscript>2</Subscript> resistance at low temperatures

A series of Ce–MnO _x /TiO₂ catalysts were prepared using a novel sol–gel template method and investigated for low-temperature selective catalytic reduction (SCR) of NO with NH₃ at temperatures ranging from 353 to 473 K. The 0.07Ce–MnO _x /TiO₂ catalyst showed the highest activity and best resistance to SO₂ poisoning. The structure and properties of the catalysts were characterized using X-ray diffraction (XRD) analysis, thermogravimetric analysis (TGA), thermogravimetry (TG)–differential scanning calorimetry (DSC)–mass spectroscopy (MS), high-resolution transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller (BET) measurements, H₂-temperature-programmed reduction (TPR), and NH₃-temperature-programmed desorption (TPD). The superior catalytic activity of the 0.07Ce–MnO _x /TiO₂ catalyst was probably due to a change in the active components, an increase in surface active oxygen and surface acid sites, and lower crystallinity and larger surface area with Ce doping. Furthermore, the reduction ability also became stronger. The SO₂ poisoning resistance of the 0.07Ce–MnO _x /TiO₂ catalyst improved because doping with Ce can effectively decrease the formation of ammonium salt on the catalyst surface and the sulfation of MnO _x . In situ diffuse-reflectance infrared Fourier-transform (DRIFT) spectroscopy experiments indicated that addition of Ce could promote adsorption of NH₃ and inhibit generation of some nitryl species. The SCR reactions over the catalysts mainly followed the Eley–Rideal mechanism accompanied with a partial Langmuir–Hinshelwood mechanism.