Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Mesoporous titania photocatalyst: effect of relative humidity and aging on the preparation of mesoporous titania and on its photocatalytic activity performance

Mesoporous TiO₂ has been synthesized by the sol–gel method, using a nonionic triblock copolymer P123 as surfactant template under acidic conditions. The as-prepared samples were characterized by thermogravimetry–differential thermal analysis (TG–DTA), nitrogen absorption–desorption (BET), field emission scanning electron microscopy, and transmission electron microscopy. The photocatalytic activity of the mesoporous TiO₂ was evaluated by degradation of methylene blue under high-intensity UV light irradiation; the amount of methylene blue was measured by UV–visible spectroscopy. TG–DTA analysis revealed that the surfactant had been removed partly in as-synthesized samples. BET analysis proved that all the samples retained mesoporosity with a narrow pore-size distribution (4.5–6.3 nm) and high surface area (103–200 m²/g). All calcined mesoporous TiO₂ had high photocatalytic activity in the photodegradation of methylene blue.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Single-step solvothermal synthesis of mesoporous anatase TiO<Subscript>2</Subscript>-reduced graphene oxide nanocomposites for the abatement of organic pollutants

In the present work, we have fabricated a novel mesoporous TiO₂–rGO nanocomposite by a facile one-step solvothermal method using titanic sulfate as the TiO₂ source. The as-prepared composites were characterized by transmission electron microscopy, X-ray diffraction; UV–Vis diffuse reflectance spectra, X-ray photoelectron spectroscopy and photoluminence spectra. In situ nucleation and anchoring of TiO₂ nanoparticles onto a graphene sheet is favorable fpr forming an intimate interfacial contact, and the chemically bonded TiO₂–rGO nanocomposites commendably enhanced their photocatalytic activity in the photodegradation of rhodamine B and phenol. The high photocatalytic activity of the as-synthesized nanocomposites are primarily ascribed to the mesoporous structure, efficient charge transportation and separation with enhanced visible light absorption, which come from the appealing nanoarchitecture, for instance, ultra-dispersed and ultra-small TiO₂ nanocrystals along with intimate and absolute interfacial contact between the TiO₂ nanocrystals and the graphene sheet.     

Template‐free Fabrication of Hierarchical Macro‐/mesoporous N‐doped TiO2/graphene Oxide Composites with Enhanced Visible‐light Photocatalytic Activity

Hierarchical macro‐/mesoporous N‐doped TiO₂/graphene oxide (N‐TiO₂/GO) composites were prepared without using templates by the simple dropwise addition mixed solution of tetrabutyl titanate and ethanol containg graphene oxide (GO) to the ammonia solution, and then calcined at 350 °C. The as‐prepared samples were characterized by scanning electron microscopy (SEM), Brunauer‐Emmett‐Teller (BET) surface area, X‐ray diffraction (XRD), Raman spectroscopy, X‐ray photoelectron spectroscopy (XPS), and UV‐Vis absorption spectroscopy. The photocatalytic activity was evaluated by the photocatalytic degradation of methyl orange in an aqueous solution under visible‐light irradiation. The results show that N‐TiO₂/GO composites exhibited enhanced photocatalytic activity. GO content exhibited an obvious influence on photocatalytic performance, and the optimal GO addition content was 1 wt%. The enhanced photocatalytic activity could be attributed to the synergetic effects of three factors including the improved visible light absorption, the hierarchical macro‐mesoporous structure, and the efficient charge separation by GO.     

Enhancement of visible-light photocatalytic activity of Cu-doped TiO<Subscript>2</Subscript> nanoparticles

Bare TiO₂ and Cu-doped TiO₂ nanoparticles with different nominal doping amounts of Cu ranging from of 0.5 to 5.0 mol% were synthesized using the modified sol–gel method. The samples were physically characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller-specific surface area, UV–Vis diffuse reflectance spectroscopy, zeta potential, X-ray photoelectron spectroscopy, inductively coupled plasma, and photoluminescence techniques. The Cu-doped TiO₂ exhibited good photocatalytic activity in mineralization of oxalic acid and formic acid under visible light irradiation. Photomineralization of oxalic and formic acids under visible light irradiation revealed greatly enhanced photoactivity exhibited by the 2.0 mol% Cu-doped TiO₂ photocatalyst compared to bare TiO₂ . The enhanced photocatalytic performance arises from copper ion doping in the TiO₂ structure, leading to an extended photoresponsive range, enhanced photogenerated charge separation, and transportation efficiency.     

Charge separation by tetrahexahedron-SrTiO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> heterojunction as an efficient photocatalyst

Charge separation plays a key role in the conversion of solar energy into chemical energy for use in the redox reaction and as well as in the photocatalytic activity. In this study, SrTiO₃ particles with different morphologies including irregular, tetrahexahedron, and cube were synthesized by an in situ solvothermal method. The photocatalytic activity of the synthesized nanoparticles was investigated in the photocatalytic decomposition of methylene blue under UV light irradiation. Tetrahexahedron SrTiO₃ particles exhibited high decomposition activity (70 %), which is about two times higher than those of the irregular and cubic SrTiO₃ particles. The high decomposition activity of tetrahexahedron SrTiO₃ particles could be attributed to the improvement of charge separation achieved on different crystal facets. To reach a good charge separation, tetrahexahedron SrTiO₃/TiO₂ coupled nanoparticles were fabricated by impregnation method. Results showed that coupling tetrahexahedron SrTiO₃ with TiO₂ could produce efficient charge separation between tetrahexahedron SrTiO₃ and TiO₂ due to their matched band edges. In order to achieve better charge separation, the tetrahexahedron SrTiO₃/90 %TiO₂ sample was calcined at different temperatures in the 450–750 °C range. Tetrahexahedron SrTiO₃/90 %TiO₂ coupled nanoparticles calcined at 650 °C show high photocatalytic activity compared with other samples. The prepared samples were characterized by using various techniques such as X-ray diffraction, scanning electron microscopy, photoluminescence emission spectra, and UV–Vis diffuse reflectance spectroscopy.     

Photocatalytic Degradation of Organic Reactive Dyes over MnTiO3/TiO2 Heterojunction Composites Under UV‐Visible Irradiation

In this study, the photocatalytic degradation of organic reactive dyes have been investigated using MnTiO₃/TiO₂ heterojunction composites in the presence of electron acceptors under UV‐Visible light irradiation. This MnTiO₃/TiO₂ heterojunction composites were prepared by annealing different mass ratios of pyrophanite MnTiO₃ (3–11 wt%) and TiO₂ at 300°C. All the MnTiO₃/TiO₂ heterojunction composites were characterized by spectral techniques like X‐ray diffraction (XRD), scanning electron microscope (SEM) and diffused reflectance UV‐visible spectroscopic analysis (DRS). Among them, 9 wt% MnTiO₃/TiO₂ heterojunction composites exhibited higher photocatalytic activity for the degradation of Reactive Blue 4 (RB 4). The photocatalytic efficiency of 9 wt% MnTiO₃/TiO₂ heterojunction composites was further enhanced by the addition of substantial amount of electron acceptors like hydrogen peroxide (H₂O₂) and ammonium peroxydisulfate ([NH₄]₂S₂O₈). The presence of oxidants (electron acceptors) facilitates the fast degradation of dye solution even in higher concentration upto 200 mg/L. The photocatalytic activity of MnTiO₃/TiO₂ heterojunction composites was also studied for the degradation of other four different structured reactive dyes. The extent of mineralization of these organic reactive dyes during photocatalytic degradation was estimated from COD analysis. MnTiO₃/TiO₂ heterojunction composites was also found to have good photostability in the presence of oxidants.     

Degradation of 2-Nitrophenol by Dielectric Barrier Discharge System: The Influence of Carbon Doped TiO<Subscript>2</Subscript> Photocatalyst Supported on Stainless Steel Mesh

This study investigated the degradation of 2-nitrophenol (2-NP) in aqueous solution by dielectric barrier discharge (DBD) system alone and its combination with supported TiO₂ photocatalysts. The TiO₂ photocatalyst supported on a stainless steel mesh was synthesised using sol–gel solution of 8% polyacrylonitrile (PAN)/dimethylformamide/TiCl₄ followed by pyrolysis in the furnace under N₂ atmosphere at temperatures of 300, 350, or 400 °C for 3 h holding time. The supported catalysts were characterized for their morphologies, functional groups, crystallinity, surface areas and elemental chemical states by high resolution scanning electron microscope (HRSEM), Fourier transform infrared, X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) surface area, and X-ray photoelectron spectroscopy. The influence of solution pH on the degradation of 2-NP was investigated. The residual concentration of 2-NP and the intermediate compounds were quantified and identified using high-performance liquid chromatography coupled with mass spectrometry (HPLC–MS). The concentration of the dissolved ozone, hydrogen peroxide and hydroxyl radicals generated by the DBD in the presence or absence of a catalyst was monitored using ultraviolet–visible spectroscopy and photoluminescence spectroscopy. The HRSEM, HRTEM, XRD and BET analysis revealed that the optimal thermal conditions to obtain well supported uniformly grown, highly active crystalline TiO₂ catalysts with high specific surface area was 350 °C at a 3 h holding time in N₂ atmosphere with a flow rate of 20 mL/min. The supporting procedure simultaneously carbon doped the photocatalyst. The DBD system alone without catalysts successfully mineralised 58.6% of 2-NP within 60 min while combined DBD/supported TiO₂ nanocrystals achieved 77.5% mineralisation within the same treatment time. The increase in mineralisation rate was attributed to the existence of a synergistic effect between the DBD system and the supported catalysts. 2-NP degradation proceeded via hydroxylation, nitration and denitration using DBD alone and combined DBD/Supported TiO₂ photocatalyst. Catechol, hydroquinone, hydroxyl-1,4-benzoquinone, 2-nitrohydroquinone, and 2,4-dinitrophenol were identified as major intermediate products. The order of production of free reactive species by DBD alone and combined DBD with supported photocatalyst was OH° > H₂O₂ > O₃.The results showed that the combined system was more than effective than DBD alone for the degradation of the 2-NP in aqueous solution.     

Cooperation among N,F and Fe in tri-doped TiO<Subscript>2</Subscript> photocatalyst

TiO₂ photocatalysts tri-doped with N, F and Fe were synthesized by a sol–gel method. The cooperation of N, F and Fe in tri-doped TiO₂ was verified by monitoring NH₃ decomposition, X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–Vis) absorption spectroscopy, and by the simulation based on the density functional theory (DFT). The results from NH₃ decomposition revealed that the cooperation of N, F and Fe broadened the optical response of TiO₂ to the visible light range and also enhanced the photocatalytic activity of TiO₂ under UV light. The reusability of the tri-doped TiO₂ sample after three cycles under UV and visible light irradiation was very good. XRD patterns and SEM and HRTEM images indicated that the tri-doped sample was nanometric anatase with a small amount of rutile with an average particle size of 18 nm. Tri-doping with N, F and Fe suppressed the phase transition from anatase to rutile and also resulted in some more lattice defects. XPS analysis showed that the N, F and Fe atoms were doped into the TiO₂ lattice. UV–Vis absorption spectra of the tri-doped TiO₂ showed that its optical absorption edge was moved up to 640 nm and its UV absorption was also enhanced. The DFT results confirmed that the cooperation of Fe 3d and N 2p orbits narrowed the band gap of TiO₂ and the F 2p orbit broadened the upper valence bands. The synergistic electron density around N, F and Fe in tri-doped TiO₂ was capable of enhancing the photochemical stability and reusability of TiO₂.     

Chitosan-modified TiO<Subscript>2</Subscript> as photocatalyst for ethanol reforming under visible light

This work reports the reforming of bio-ethanol on chitosan–TiO₂ hybrid photocatalysts at ambient temperature. The influence of chitosan composition on the photocatalytic performance of chitosan–TiO₂ hybrid was studied. The hybrids were characterized by CHN elemental analysis, nitrogen adsorption–desorption isotherms, thermogravimetric analysis, diffuse reflectance spectroscopy, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The results showed that the preparation variables used for the incorporation of chitosan on TiO₂ promoted changes in the morphology, superficial area, crystal size and porosity of the photocatalyst, affecting the band gap of this semiconductor and consequently the reactivity of the chitosan–TiO₂ hybrids. The catalysts were evaluated for hydrogen production from ethanol under visible light. It was demonstrated that the calcination temperature of 623 K and a chitosan content of 20% were the most appropriate preparation conditions and the resulting product displays a pore size of 1.9 nm, crystal size of 11.3 nm, BET area of 178 m² g^?1 and band gap of 2.92 eV. The calcination temperature of 623 K and incorporation of 20% of chitosan obtained the same results in the conversion rate of hydrogen in comparison to the pure TiO₂ P25.     

Persistent photocatalysis of continuously flowing gas-phase nitric oxide using CaAl2O4:(Eu,Nd)/rutile phase TiO2−x N y composites

CaAl₂O₄:(Eu,Nd)/rutile phase TiO_2?x N _y composites were synthesized via a two-step method, i.e. a solvothermal reaction followed by a mechanochemical treatment. The photocatalytic deNO _x activity of the composites was evaluated under UV light (λ > 290 nm) irradiation and after turning off the UV light. It was confirmed that rutile phase TiO_2?x N _y nanoparticles could be uniformly dispersed on the surface of CaAl₂O₄:(Eu,Nd) after planetary ball milling treatment. The composites prepared by this two-step method had high photocatalytic activity and good prolonged catalysis time even after turning off the light.     

Preparation of CdS–TiO2/Fe3O4 photocatalyst and its photocatalytic properties

The CdS modified TiO₂/Fe₃O₄ photocatalysts were prepared by sol–gel and immersion methods. The morphological, structural and optical properties of as-prepared samples were characterized by X-ray diffraction (XRD), UV–Vis absorption spectra, X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). The TEM observation showed that the surface of magnetite particles (Fe₃O₄) were coated by CdS–TiO₂ layer as loose clusters, and average diameter of composites particles was about 250 nm. UV–Vis absorption spectra indicated that CdS–TiO₂/Fe₃O₄ composites had pronounced red-shift compared with that of TiO₂/Fe₃O₄. The CdS–TiO₂/Fe₃O₄ composites exhibit higher photocatalytic activity than pure TiO₂ and TiO₂/Fe₃O₄ for the degradation of Reactive Brilliant Red X-3B dye (X-3B) aqueous solution under simulated sunlight, and the optimum content of CdS is 1.0 % (mol ratio of CdS to TiO₂). In addition, a gradual loss of photocatalytic activity can be observed in reusability test of CdS–TiO₂/Fe₃O₄ composites, and degradation of X-3B reached still to 78.9 % after five runs.     

Core-shell structure CdS/TiO2 for enhanced visible-light-driven photocatalytic organic pollutants degradation

CdS modified mesoporous titania core-shell spheres (CdS/CS-TiO₂) with enhanced visible-light activity were synthesized by an in situ method. This method included two steps: planting CdO into the framework of anatase TiO₂ core-shell spheres and then converting it to CdS by ion-exchange. The physicochemical properties of the obtained samples were investigated by X-ray diffraction, scanning electron microscopy, transmission electronic micrograph, UV–vis diffuse reflectance spectra and nitrogen sorption. The in situ strategy resulted in CdS quantum dots highly dispersed in CS-TiO₂ without destroying the mesoporous core-shell structure. Compared with CS-TiO₂, the as-synthesized samples exhibited stronger visible-light absorption capability and greatly enhanced photocatalytic activity toward the degradation of Rhodamine B and 4-chlorophenol aqueous solution under visible light irradiation (λ > 420 nm).     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Synthesis and Characterization of Spindle-Like TiO<Subscript>2</Subscript> Nanostructures and Photocatalytic Activity on Methyl Orange and Methyl Blue Dyes Under Sunlight Radiation

Spindle-like TiO₂ nanostructures was prepared by a simple one pot solvothermal method followed by calcination at 400 °C for 3 h. The sample was characterized using various techniques such as X-ray diffractometer, transmission electron microscopy, Fourier transform infrared spectroscopy and UV–Vis absorption spectroscopy. The crystal structure of TiO₂ nanostructure was measured by X-ray diffractometer. According to the XRD result, the peaks in the sample can be indexed to anatase phase of TiO₂. The morphological characterization of TiO₂ sample was examined by transmission electron microscopy. The synthesized sample consisted of spindle-like shape with size in the range of 50–70 nm. The band gap value of Spindle-like TiO₂ nanostructures is 2.92 eV, which is lower than that of bulk TiO₂ of 3.2 eV. The FTIR bands observed at 493, 443 and 428 cm^?1 confirms the presence of TiO₂. The Spindle-like TiO₂ nanostructures showed photodegradation ability for methyl orange and methyl blue dye. The reuse evaluation of the Spindle-like TiO₂ nanostructures showed that their photocatalytic activity had good durability.     

Photocatalytic degradation of trichloroethylene on platinum ion-doped TiO<Subscript>2</Subscript> under visible light irradiation

Porous platinum ion-doped TiO₂ (Pt–TiO₂) was prepared by a sol–gel method and demonstrated to have superior photocatalytic activity for the photodegradation of gaseous trichloroethylene (TCE) under visible light (VL) irradiation from a xenon lamp equipped with 422-nm cut-off filter. Kinetic studies were performed to clarify the effect of the doping amounts, space times, VL intensity, and mole fractions of TCE, O₂, and H₂O on the degradation of TCE. Under ultraviolet (UV) irradiation, the photocatalytic activity of Pt–TiO₂ was the same as that of TiO₂, indicating that the doped Pt ion did not act as a recombination center for the photogenerated holes and electrons. Based on the kinetic data and reaction products, we conclude that the photocatalytic degradation of TCE on Pt–TiO₂ under VL irradiation proceeds similarly to TiO₂ under UV irradiation. We also performed the photocatalytic degradation of TCE at the space time of 7.5 × 10⁷ g s mol^?1 in a tubular reactor packed with the Pt–TiO₂ pellets which are more suitable than the Pt–TiO₂ powder for the practical remediation of the contaminated gas. TCE was completely degraded, i.e. 100% conversion was achieved under VL irradiation but only a small quantity of CO₂ was formed with the stoichiometric ratio of [CO₂]_formed/[TCE]_degraded of ca. 0.33. By switching the gas stream containing TCE to humid air, more CO₂ was formed, indicating that the dichloroacetates accumulated on the Pt–TiO₂ surface are photodegradable to CO₂ under VL irradiation.     

Fe2O3/ZnO/ZnFe2O4 composites for the efficient photocatalytic degradation of organic dyes under visible light

In this study, novel ternary Fe₂O₃/ZnO/ZnFe₂O₄ (ZFO) composites were successfully prepared through a simple hydrothermal reaction with subsequent thermal treatment. The as-prepared products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET) analysis, Barrett-Joyner-Halenda (BJH) measurement, and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). The photocatalytic degradation of rhodamine B (Rh B) under visible light irradiation indicated that the ZFO composites calcined at 500 °C has the best photocatalytic activity (the photocatalytic degradation efficiency can reach up to 95.7% within 60 min) and can maintain a stable photocatalytic degradation efficiency for at least three cycles. In addition, the photocatalytic activity of ZFO composites toward dye decomposition follows the order cationic Rh B > anionic methyl orange. Finally, using different scavengers, superoxide and hydroxyl radicals were identified as the primary active species during the degradation reaction of Rh B.     

Synthesis and photocatalytic activity of nanocrystalline TiO2 co-doped with nitrogen and cobalt(II)

Nitrogen-modified cobalt-doped TiO₂ materials were successfully prepared via a modified sol–gel method. The structure and properties of the catalysts were characterized via X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution TEM, ultraviolet–visible light diffuse reflectance spectra (UV–Vis DRS), N₂ adsorption–desorption isotherms, and energy-dispersive X-ray spectroscopy. The XRD patterns of the pure and co-doped TiO₂ samples indicate that the predominant phase was anatase. The average grain size obtained from TEM was approximately 10 nm. The Brunauer–Emmett–Teller analysis results indicate that the specific surface area was 77.7 m² g^?1. The UV–Vis DRS results for the co-doped sample reveal an absorption edge that had been red-shifted to 500 nm. The photocatalytic activities of the samples were evaluated through photodegradation of papermaking wastewater under UV and visible light irradiation. Compared with the cobalt-doped TiO₂ sample and Degussa P25, the 3 mol% N-doped mesoporous N/Co-TiO₂ photocatalyst exhibited the highest photocatalytic activity, which can be ascribed to the synergistic effect of the N and Co co-doping.     

Preparation of mesoporous TiO2/CNT nanocomposites by synthesis of mesoporous titania via EISA and their photocatalytic degradation under visible light irradiation

Stabilized mesoporous TiO₂ was synthesized by evaporation induced self assembly (EISA) method and mechanically incorporated into single-walled carbon nanotubes (SWCNT) with different ratios. The physicochemical properties of the nanocomposites (mesoporous TiO₂/SWCNT) materials were investigated by Brunauer–Emmett–Teller (BET) measurement, X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX), photoluminescence (PL) and ultraviolet–visible (UV–Vis) spectroscopy measurements. The catalytic activity of mesoporous TiO₂ and nanocomposites were assessed by examining the degradation of rhodamine B as model aqueous solution under visible light. CNTs are facilitating the photocatalytic activity of mesoporous TiO₂ in the degradation of rhodamine B efficiently.