AC impedance, FTIR and XRD investigations of poly acrylonitrile complexed with LiCF3SO3

Solid polymer electrolytes of high ionic conductivity are prepared using poly acrylonitrile (PAN), propylene carbonate (PC), ethylene carbonate (EC) and LiCF₃SO₃. The polymer films are characterised by X-ray diffraction, FTIR and a.c. impedance spectroscopic techniques. The conductivity studies of PAN-LiCF₃SO₃-PC-EC polymer electrolyte systems are carried out in the temperature range 301–373 K. The temperature dependence of the conductivity of the polymer films obeys the VTF relation. The conductivity values are presented and the results are discussed.     

Ionic conduction behavior in PVC–PEG blend polymer electrolytes upon the addition of TiO2

The blend-based polymer electrolyte consisting of poly (vinyl chloride) (PVC) and poly (ethylene glycol) (PEG) as host polymers and lithium perchlorate (LiClO₄) as the complexing salt was studied. An attempt was made to investigate the effect of TiO₂ concentration in the unplasticized PVC–PEG polymer electrolyte system. The XRD and FTIR studies confirm the formation of a polymer–salt complex. The conductivity results indicate that the incorporation of ceramic filler up to a certain concentration (15 wt.%) increases the ionic conductivity and upon further addition the conductivity decreases. The maximum ionic conductivity 0.012 × 10⁻⁴ S cm⁻¹ is obtained for PVC–PEG–LiClO₄–TiO₂ (75–25–5–15) system. Thermal stability of the polymer electrolyte is ascertained from TG/DTA studies.     

Investigation on compositional effect of PEG:BaTiO<Subscript>3</Subscript> in plasticized PVC–LiBETi polymer composite electrolytes

The blend-based polymer electrolyte comprising poly(vinyl chloride) (PVC) and poly(ethylene glycol) (PEG) as host polymer and lithium bis(perfluoroethanesulfonyl)imide as complexing salt have been prepared. Ethylene carbonate and dimethyl carbonate (50:50 v/v) are used as plasticizer for the system. The barium titanate is used as a filler, and the ratio of (PEG:BaTiO₃) is varied to study its effect on the conductivity behavior of the electrolyte. XRD and ac impedance studies are carried out on the prepared samples. The ac impedance measurements show that the conductivity of the prepared samples depends on the (PEG:BaTiO₃) ratio, and its value is higher for (15:5) wt.% of (PEG:BaTiO₃)-incorporated film. The temperature dependence of the conductivity of the polymer films obeys VTF relation. The role of ferroelectric filler in enhancing the conductivity is studied. The thermal stability of the film is ascertained from TG/DTA studies. The phase morphological study reveals that the porous nature of the polymer electrolyte membranes depends on the (PEG:BaTiO₃) ratio.     

Conductivity, dielectric behaviour and thermal stability studies of lithium ion dissociation in poly(methyl methacrylate)-based gel polymer electrolytes

Thin films of poly(methyl methacrylate) (PMMA) with lithium triflate (LiCF₃SO₃) were prepared by using the solution-casting method with PMMA as the host polymer. Ionic conductivity and dielectric measurements were carried out on these films. The highest conductivity for polymer electrolyte with a ratio of 65:35 was found to be 9.88 × 10⁻⁵ S cm⁻¹, which is suitable for the production of mobile phone battery. Thermal gravimetric analysis was carried out to evaluate the thermal stability of the polymer electrolyte. The addition of salts will increase thermal stability of the polymer electrolyte.     

Ionic conductivity and battery characteristic studies on PEO+NaClO3 polymer electrolyte

Solid polymer electrolyte films based on poly (ethylene oxide) PEO complexed with NaClO₃ have been prepared by a solution-cast technique. The solvation of Na⁺ ion with PEO is confirmed by XRD and IR studies. Measurements of the a.c. conductivity in the temperature range 308 – 378 K and the transference numbers have been carried out to investigate the charge transport in this polymer electrolyte system. Transport number data show that the charge transport in this polymer electrolyte system is predominantly due to ions. The highest conductivity (2.12.10⁻⁴ S/cm) has been observed for the 70:30 composition. Using the polymer electrolyte solid state electrochemical cells have been fabricated. The various cell parameters are evaluated and reported.     

Effect of ZnO nanoparticles filler concentration on the properties of PEO-ENR50-LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript> solid polymeric electrolyte

A solid polymer electrolyte comprising blend of poly(ethylene oxide) and 50% epoxidized natural rubber (ENR50) as a polymer host, LiCF₃SO₃ as a salt and nanoparticle ZnO as an inorganic filler was prepared by solution-casting technique. The effect of filler on the electrolyte properties was characterized and analysed. FESEM analysis showed that the filler was well distributed in the polymer matrix, while the effective interaction between the salt and the polymer host was reduced by the addition of filler. As evidenced by FTIR analysis, which showed the formation of triplet peak at C-O-C stretching region. Ionic conductivity was found to decrease from 1.4 × 10⁻⁴ Scm⁻¹ to 2.5 × 10⁻⁶ Scm⁻¹ upon the addition of filler, due to the blocking effect of filler into the electrolyte conduction pathways. The temperature dependence on the electrolyte conductivity obeys Arrhenius rule in two temperature regions.     

Effect of lithium salt concentration in PVAc/PMMA-based gel polymer electrolytes

Hybrid solid polymer electrolyte films comprising of poly(vinyl acetate) (PVAc), poly(methyl methacrylate) (PMMA), LiClO₄, and propylene carbonate are prepared by solution casting technique by varying the salt concentration. In this study, PVAc/PMMA polymer blend ratio is fixed as 25:75 on the basis of conductivity and mechanical stability of the film. X-ray diffraction, Fourier transform infrared impedance, thermogravimetry/differential thermal analysis and scanning electron microscopy studies are carried out for the polymer electrolytes. The maximum ionic conductivity is found to be 4.511 × 10⁻⁴ S cm⁻¹ at 303 K for the plasticized polymer electrolyte with 8 wt.% of LiClO₄. The ionic conductivity is found to decrease with an increase of LiClO₄ concentration.     

Experimental investigations on plasticized PMMA/PVA polymer blend electrolytes

Blend based polymer electrolytes composed of poly (methyl methacrylate) (PMMA), poly(vinylalcohol) (PVA) and LiClO₄ are prepared using solvent casting technique. The polymer films are characterized by XRD and FTIR studies to determine the molecular environment for the conducting ions. These polymer films have been investigated in terms of ionic conductivity using the results of impedance studies. The influence of the blend composition on the electrochemical behaviour is also discussed. The highest room temperature conductivity obtained for the film consisting of PMMA, PVA, LiClO₄ and DMP is 0.06×10⁻³ S/cm at 303 K. The PMMA-PVA blend based polymer electrolytes look very desirable and promising for lithium battery applications.     

Investigation of dibutyl phthalate as plasticizer on poly(methyl methacrylate)–lithium tetraborate based polymer electrolytes

Polymer electrolyte membranes, comprising of poly(methyl methacrylate) (PMMA), lithium tetraborate (Li₂B₄O₇) as salt and dibutyl phthalate (DBP) as plasticizer were prepared using a solution casting method. The incorporation of DBP enhanced the ionic conductivity of the polymer electrolyte. The polymer electrolyte containing 70 wt.% of poly(methyl methacrylate)–lithium tetraborate and 30 wt.% of DBP presents the highest ionic conductivity of 1.58 × 10⁻⁷ S/cm. The temperature dependence of ionic conductivity study showed that these polymer electrolytes obey Vogel–Tamman–Fulcher (VTF) type behaviour. Thermogravimetric analysis (TGA) was employed to analyse the thermal stability of the polymer electrolytes. Fourier transform infrared (FTIR) studies confirmed the complexation between poly(methyl methacrylate), lithium tetraborate and DBP.     

Conductivity studies on PEO:NaClO3 electrolyte system with different plasticizers

A new ion conducting solid polymer electrolyte thin film based on Polyethylene oxide (PEO) with NaClO₃ salt is prepared by solution-casting method. The solvation of salt with PEO has been confirmed by X-ray diffraction and IR spectral studies. Plasticizer effects were studied in PEO:NaClO₃ system by using low molecular weight polyethylene glycol (PEG), dimethyl formamide (DMF) and propylene carbonate(PC). AC conductivity in the temperature range (308–378 K) was measured to evaluate the conductivity of the polymer electrolytes. From the conductivity data, it was found that the conductivity value of pure PEO increases 10²–10⁴ order of magnitude with the addition of salts as well as plasticizers. From the transference number experiments, it was confirmed that the charge transport in these electrolyte is mainly due to the ions (t_ion≈0.94). Finally, the conductivity value of all PEO: NaClO₃ systems were compared.     

High ionic conductive behavior of cyanoethylated polyvinylalcohol- and polyacrylonitrile-based electrolytes

New type polymer electrolyte films based on poly(acrylonitrile), (PAN), and cyanoethylated poly(vinyl alcohol), (CN-PVA), were prepared and their conducting behaviors were investigated. CN-PVA was prepared from poly(vinyl alcohol), (PVA) and acrylonitrile in the presence of sodium hydroxide and quaternary ammonium halide as a phase transfer catalyst. Free standing PAN- and CN-PVA-based electrolyte films were prepared by casting the propylene carbonate (PC) solution containing PAN, CN-PVA and LiClO₄ and removing some amount of PC. Ionic conductivity of the electrolyte film, (PAN)10(CN-PVA) 10(LiClO₄)8(PC)4 composite film was 14.6 mS cm^− 1 at 30 °C and 22.4 mS cm^− 1 at 60 °C. FTIR results for the electrolyte films suggest that the nitrile groups in the CN-PVA matrix mainly interact with the lithium ions in the films and enhance dissolution of the lithium salt in the electrolyte films.     

Structural and electrochemical characteristics of 49% PMMA grafted polyisoprene-LiCF3SO3-PC based polymer electrolytes

Gel polymer electrolytes consisting of 49% PMMA grafted polyisoprene-LiCF₃SO₃, were plasticized with propylene carbonate (PC) are reported. The effect of PC on the electrochemical properties of the polymer electrolyte has been investigated. Analysis of FTIR spectra shows the interaction of salt and plasticizers with the polymer chain. The ionic conductivity was measured and exhibited a maximum value of 10⁻⁴ S/cm. The temperature dependence of the electrical conductivity follows the Arrhenius law. Paper presented at the International Conference on Functional Materials and Devices 2005, Kuala Lumpur, Malaysia, June 6 – 8, 2005.     

Conductivity studies of plasticized proton conducting PVA–PVIM blend doped with NH4BF4

The proton conducting solid-state polymer electrolyte comprising blend of poly(vinyl alcohol) (PVA) and poly(N-vinylimidazole) (PVIM), ammonium tetrafluoroborate (NH₄BF₄) as salt, and polyethylene glycol (PEG) (molecular weight 300 and 600) as plasticizer is prepared at various compositions by solution cast technique. The prepared films are characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy analysis. The conductivity–temperature plots are found to follow an Arrhenius nature. The conductivity of solid polymer electrolytes is found to depend on salt and plasticizer content and also on the dielectric constant value and molecular weight of the plasticizer. Maximum ionic conductivity values of 2.20?×?10^?4 and 1.28?×?10^?4?S?cm^?1 at 30 °C are obtained for the system (PVA–PVIM)?+?20 wt.% NH₄BF₄?+?150 wt.% PEG300 and (PVA–PVIM)?+?20 wt.% NH₄BF₄?+?150 wt.% PEG300, respectively. The blended polymer, complexed with salt and plasticizer, is shown to be a predominantly ionic conductor. The proton transport in the system may be expected to follow Grotthuss-type mechanism.     

Synthesis and studies of new plasticized PVP: NaClO3 electrolyte system for battery applications

A new thin film sodium ion conducting plasticized polymer electrolyte based on poly(vinyl pyrrolidone) (PVP) complexed with NaClO₃ salt systems was prepared by the solution-cast method. The interaction of NaClO₃ salt with PVP was confirmed by Infrared (IR) study. Charge transport of these polymer electrolytes is due to ions, which was confirmed by Wagner’s polarization method. From the conductivity measurements, the highest conductivity value 6.71×10⁻⁵ S/cm was observed for the composition PVP:PEG:NaClO₃(30:60:10) at room temperature 35 °C. The redox behaviour and good reversibility of the plasiticized electrolytes are confirmed by electrochemical techniques. Electrochemical cell studies of these polymer electrolytes were analyzed from their discharge characteristics. The open-circuit voltage (OCV) and short-circuit current (SCC) were found to in the range of 2.52 V to 2.36 V and 760 μA to 1040 μA, respectively.     

Impact of ethylene carbonate on electrical properties of PVA/(NH4)2SO4/H2SO4 proton-conductive membrane

A new proton-conductive membrane (PCM) based on poly (vinyl alcohol) and ammonium sulfate (NH₄)₂SO₄ complexed with sulfuric acid and plasticized with ethylene carbonate (EC) at different weight percent were prepared by casting technique. The structural properties of these electrolyte films were examined by XRD studies. The XRD patterns of all the prepared polymer electrolytes reveal the amorphous nature of the films. ac conductivity and dielectric spectra of the electrolyte were studied with changing EC content from weight 0.00 to 0.75 g. A maximum conductivity of 7.3 × 10⁻⁵ S cm⁻¹ has been achieved at ambient temperature for PCM containing 0.25 g of ethylene carbonate. The electrical conductivity σ, dielectric constant ε′ and dielectric loss ε″ of PCM in frequency range (100 Hz to 100 KHz), and temperature range (300–400 K) were carried out. Measurement of transference number was carried out to investigate the nature of charge transport in these polymer electrolyte films using Wagner’s polarization technique. Transport number data showed that the charge transport in these polymer electrolyte systems was predominantly due to ions. The electrolyte with the highest electrical conductivity was used in the fabrication of a solid-state electrochemical cell with the configuration (Mg/PCM/PbO₂). Various cell parameters ldensity, and current density were determined. The fabricated cells gave capacity of 650 μAh and have an internal resistance of 11.6 kΩ.     

Structural and electrical properties of pure and NaBr doped poly (vinyl alcohol) (PVA) polymer electrolyte films for solid state battery applications

A sodium ion conducting polymer electrolyte based on poly (vinyl alcohol) (PVA) complexed with sodium bromide (NaBr) was prepared using solution cast technique. Several experimental techniques such as XRD, FTIR, SEM, temperature-dependant conductivity and transference number measurements have been performed. XRD and FTIR studies confirm the complexation of salt with the polymer. Surface morphology was studied using Scanning Electron Microscopy. DC conductivity was measured in the temperature range of 303–373 K, and the conductivity was found to increase with the increase of dopant concentration as well as temperature. Transference number data suggests that the charge transport in this polymer electrolyte system is mainly due to ions. Using these polymer electrolyte films, electrochemical cells were fabricated with configuration Na/(PVA:NaBr)/V₂O₅ and Na/(PVA:NaBr)/(I2+C+electrolyte) and their discharge characteristics like open circuit voltage (OCV), short circuit current (SCC), power density, energy density were evaluated and compared. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Ionic conduction and thermal properties of poly(ethylene oxide) - Er (CF3SO3)3 films

Measurements of electrical conductivity and thermal behaviour have been carried out on polymer electrolyte films obtained by the addition of erbium triflate to poly(ethylene oxide), PEO. Homogeneous electrolyte samples were prepared by using solvent casting and hot-pressing techniques to produce films with a composition defined by the general formula (EO)_nEr(CF₃SO₃)₃, where n lies between 3 and 150. This electrolyte system was found to behave in a manner broadly similar to other trivalent salt containing polymer electrolytes, however, in contrast to previously studied lanthanide systems, a salt - polymer complex crystallized after prolonged annealing of salt rich compositions at room temperature. Paper presented at the 2nd Euroconference on Solid State Ionics, Funchal, Madeira, Portugal, Sept. 10 – 16, 1995     

Ionic conductivity studies in PMMA/PVdF polymer blend electrolyte with lithium salts

Batteries using ionically conducting polymer membranes as electrolytes are very attractive, since the concept of power sources capable of combining a high energy content with plasticity is very appealing for the consumer electronics market and in electric vehicle applications. Blend based polymer electrolytes composed of poly (methylmethacrylate) (PMMA), Poly Vinylidene fluoride (PVdF), Lithium salt (LiX) (X=ClO₄, BF₄ and CF₃SO₃) and Dimethyl Phthalate (DMP) are prepared using solvent casting technique. The films have been characterized using XRD, FTIR, Thermal and SEM studies; the effect of complexing salt and temperature on ionic conductivity is also discussed. The maximum conductivity value obtained for the solid polymer electrolyte film at 303 K is 4.2 × 10⁻³ S/cm.     

Electrical and optical properties of pure and KClO3-doped P(MMA-CO-4VPNO) polymer electrolyte films

Ion-conducting polymer electrolyte films based on a copolymer poly(methyl-methacrylate-co-4-vinyl pyridine N-oxide) [P(MMA-CO-4VPNO)] complexed with potassium chlorate (KClO₃) were prepared by solution cast technique. The complexation of KClO₃ salt with the polymer was confirmed by X-ray diffraction and infrared studies. The electrical conductivity and optical absorption of pure and KClO₃-doped P(MMA-CO-4VPNO) polymer electrolyte films have been studied. The electrical conductivity increased with increasing dopant concentration, which is attributed to the formation of charge transfer complexes. The variation of electrical conductivity with temperature shows two regions with two activation energies. Optical properties like direct band gap, indirect band gap, and optical absorption edge were investigated for pure and doped polymer films in the wavelength range 300–550 nm. It was found that the energy gaps and band edge values shifted to lower energies on doping. The behavior is in an agreement with the activation energies obtained from the conductivity data.     

Structural, conductivity, and dielectric characterization of PEO–PEG blend composite polymer electrolyte dispersed with TiO2 nanoparticles

A solid polymer electrolyte (SPE) composites consisting blend of poly(ethylene oxide) (PEO) and poly(ethylene glycol) (PEG) as the polymer host with LiCF₃SO₃ as a Li⁺ cation salt and TiO₂ nanoparticle which acts as a filler were prepared using solution-casting technique. The SPE films were characterized by X-ray diffraction and Fourier transform infrared analysis to ensure complexation of the polymer composites. Frequency-dependent impedance spectroscopy observation was used to determine ionic conductivity and dielectric parameters. Ionic conductivity was found to vary with increasing salt and filler particle concentrations in the polymer blend complexes. The optimum ambient temperature conductivity achieved was 2.66?×?10^?4?S?cm^?1 for PEO (65 %), PEG (15 %), LiCF₃SO₃ (15 %), ethylene carbonate (5 %), and TiO₂ (3 %) using weight percentage. The dielectric relaxation time obtained from a loss tangent plot is fairly consistent with the conductivity studies. Both Arrhenius and VTF behaviors of all the composites confirm that the conductivity mechanism of the solid polymer electrolyte is thermally activated.