Investigation of thermal hazard during the hydrosilylation of 1,6-divinyl(perfluorohexane) with trichlorosilane

In this study, we examined the reaction hazard during the hydrosilylation reaction between trichlorosilane (TCS) and 1,6-divinyl(perfluorohexane) (FDV) in the presence of a butanol solution of chloroplatinic acid (Pt-Cat) as the catalyst. Assuming the three industrial risks of excessive addition of Pt-Cat, contamination by iron rust and mixing with cooling water, we observed the temperature and pressure change of TCS/FDV with an excessive amount of Pt-Cat, TCS/FDV/Pt-Cat with Fe₂O₃ and TCS/FDV/Pt-Cat with distilled water, using an accelerating rate calorimeter (ARC). The temperature and pressure greatly increased, especially in the sample with Fe₂O₃. For instance, in TCS/FDV/Pt-Cat with 1.5 wt.% Fe₂O₃, the heat release rate exceeded 624 K · min^?1 and the pressure rose above 25 MPa during the exothermic reaction.     

Influence of mechanical activation time,annealing, and Fe/O ratio on Fe3O4/Fe composites formation from Fe2O3 and Fe powders mixture

Commercially, iron (α-Fe) and hematite (α-Fe₂O₃) powders were used for the synthesis of composite powders of Fe₂O₃/Fe type by mechanical milling. Several ratios of Fe₂O₃/Fe were chosen for the composite synthesis; the atomic percent of oxygen in the starting mixtures ranged from 21 to 46 %. The Fe₂O₃/Fe composite samples with various Fe/O ratios were milled for different milling times. The milled composite samples were subjected to the heat treatments in argon up to 900 °C. During the heat treatment at temperatures that do not exceed 550 °C, Fe₃O₄/Fe composite particles are formed by the reaction between the Fe₂O₃ and Fe. Further increase of the heat treatment up to 700 °C leads to the reaction of the Fe₃O₄/Fe composite component phases, resulting thus in the formation of FeO/Fe composite. The heat treatment up to 900 °C of the Fe₂O₃/Fe leads to the formation of a composite of FeO/Fe₃O₄/Fe independent of the milling time and Fe₂O₃/Fe ratios. The onset temperatures of the Fe₃O₄ and FeO formations decrease upon increasing the milling time. Another important aspect is that, in the case of the same milling time but with a large amount of iron into the composite powder the formations temperatures of Fe₃O₄ and FeO are also decreasing. The influence of the mechanical activation time, heat treatment temperature, and Fe/O ratio on the formation of the (Fe₃O₄, FeO)/Fe composite from Fe₂O₃+Fe precursor mixtures was studied by differential scanning calorimetry and X-ray diffraction techniques.     

Magnetic core–shell Fe3O4@C-SO3H nanoparticle catalyst for hydrolysis of cellulose

Catalytic hydrolysis of cellulose over solid acid catalysts is one of efficient pathways for the conversion of biomass into fuels and chemicals. High catalytic activity and easy separation from reaction media are two important factors for evaluating the performance of the solid acid catalysts for the cellulose hydrolysis. In this study, we report a core–shell Fe₃O₄@C-SO₃H nanoparticle with a magnetic Fe₃O₄ core encapsulated in a sulfonated carbon shell, as recyclable catalyst for the hydrolysis of cellulose. The sulfonated carbon shell shows a good activity, presenting 48.6 % cellulose conversion with 52.1 % glucose selectivity under the moderate conditions of 140 °C after 12 h reaction. Importantly, the magnetic Fe₃O₄ core makes the catalysts easily separated from reaction mixtures by using the externally applied magnetic field. In addition, the Fe₃O₄@C-SO₃H nanoparticle catalyst shows a high stability in the activity and magnetization during recycling tests, suggesting it a promising solid acid catalyst for the hydrolysis of cellulose.     

Facile synthesis of Fe@Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanowires as O<Subscript>2</Subscript> electrode for high-energy Li-O<Subscript>2</Subscript> batteries

Fe@Fe₂O₃ core-shell nanowires were synthesized via the reduction of Fe³⁺ ions by sodium borohydride in an aqueous solution with a subsequent heat treatment to form Fe₂O₃ shell and employed as a cathode catalyst for non aqueous Li-air batteries. The synthesized core-shell nanowires with an average diameter of 50–100 nm manifest superior catalytic activity for oxygen evolution reaction (OER) in Li-O₂ batteries with the charge voltage plateau reduced to ～3.8 V. An outstanding performance of cycling stability was also achieved with a cutoff specific capacity of 1000 milliampere hour per gram over 40 cycles at a current density of 100 mA g^?1. The excellent electrochemical properties of Fe@Fe₂O₃ as an O₂ electrode are ascribed to the high surface area of the nanowires’ structure and high electron conductivity. This study indicates that the resulting iron-containing nanostructures are promising catalyst in Li-O₂ batteries.     

Thermal stability of the manganese-nickel mixed ferrite and iron phases in the Mn0.5Ni0.5Fe2O4/Fe composite/nanocomposite powder

The composite/nanocomposite powders of Mn_0.5Ni_0.5Fe₂O₄/Fe type were synthesized starting from nanocrystalline Mn_0.5Ni_0.5Fe₂O₄ (D = 7 nm) (obtained by ceramic method and mechanical milling) and commercial Fe powders. The composites, Mn_0.5Ni_0.5Fe₂O₄/Fe, were milled for up to 120 min and subjected to heat treatment at 600 °C and 800 °C for 2 h. The manganese-nickel ferrite/iron composite samples were subjected to differential scanning calorimetry (DSC) up to 900 °C for thermal stability investigations. The composite component phases evolution during mechanical milling and heat treatments were investigated by X-ray diffraction technique. The present phases in Mn_0.5Ni_0.5Fe₂O₄/Fe composite are stable up to 400–450 °C. In the temperature range of 450-600 °C, the interdiffusion phenomena occurs leading to the formation of Fe_1?xMn_xFe₂O₄/Ni–Fe composite type. The new formed ferrite of Fe_1?xMn_xFe₂O₄ type presents an increased lattice parameter as a result of the substitution of nickel cations into the spinel structure by iron ones. Further increases of the temperature lead to the ferrite phase partial reduction and the formation of wustite-FeO type phase. The spinel structure presents incipient recrystallization phenomena after both heat treatments (600 °C and 800 °C). The mean crystallites size of the ferrite after heat treatment at 800 °C is about 75 nm. After DSC treatment at 900 °C, the composite material consists in Fe_1?xMn_xFe₂O₄, Ni structure, FeO, and (NiO)_0.25(MnO)_0.75 phases.     

Generation of sulfate radicals by supported ruthenium catalyst for phenol oxidation in water

In this study we report the preparation of RuO₂/Fe₃O₄@nSiO₂@mSiO₂ core–shell powder mesoporous catalyst for heterogeneous oxidation of phenol by peroxymonosulfate (PMS) as oxidant. The properties of this supported catalyst were characterized by SEM–EDS (scanning electron microscopy–energy dispersive X-ray spectroscopy), XRD (powder X-ray diffraction), TEM (transmission electron microscopy), and nitrogen adsorption–desorption. It is found that using ruthenium oxide-based catalyst is highly effective in activating PMS for related sulfate radicals. The effects of catalyst loading, phenol concentration, PMS concentration, reaction temperature, and reusability of the as-prepared catalyst on phenol degradation were investigated. In RuO₂/Fe₃O₄@nSiO₂@mSiO₂ mesoporous catalyst, Oxone (PMS) was effectively activated and 100 % phenol degradation occurred in 40 min. The magnetic RuO₂/Fe₃O₄@nSiO₂@mSiO₂ catalyst was facility separated from the solution by an external magnetic field. To regenerate the deactivated catalyst and improve its catalytic properties, three different methods involving annealing in air, washing with water, and applying ultrasonics were used. The catalyst was recovered thoroughly by heat treatment.     

Preparation and characterization of an active catalyst

As an active catalyst to promote thermolysis of ammonium perchlorate (AP), potassium lead hexanitrocobaltate(II) complex (K₂Pb[Co(NO₂)₆]) was synthesized by the direct deposition method and inverse microemulsion method. Its submicron, size, cube morphology, and crystal structure were investigated by SEM, TEM, and XRD analysis, respectively. Thermal decomposition of K₂Pb[Co(NO₂)₆] was studied by the TG/DSC-IR online system and XRD analysis. The catalyst was decomposed at about 300 °C; its gaseous products were NO₂, NO, and N₂O and its solid products were Pb₃O₄, Co₃O₄, PbO, CoO, and KNO₂. Because thermal decomposition of the catalyst was synchronous with low temperature decomposition of AP, thermolysis of AP was promoted remarkably. In particular, the gaseous products (NO _x ) could directly oxidize the absorbed NH₃. As a result, compared to the data of pure AP, the integral heat of AP added 3.0 wt% of the catalyst multiplied by 280 %, the maximum rate of heat release increased by 634 %. The decomposition of catalyzed AP ended at about 317 °C, at which only less than 30 % of pure AP decomposed.     

Immobilized different amines on modified magnetic nanoparticles as catalyst for biodiesel production from soybean oil

Fe₃O₄ nanoparticles were modified with tetraethylorthosilicate (TEOS) and (3-chloropropyl)trimethoxysilane (CPTMS) followed by immobilization with different amines such as guanine, piperazine, methylamine, morpholine, aniline, ethylenediamine, 3-aminopropyltriethoxysilane, and melamine, designated as Fe₃O₄@SiO₂@CPTMS@amine (nanocatalyst). The prepared nanocatalysts were characterized by means of FTIR, XRD, VSM, SEM, and TEM. Trans-esterification reactions of soybean oil with methanol were then carried out in the presence of the Fe₃O₄@SiO₂@CPTMS@amine as a nanocatalyst. Optimization of the reaction parameters revealed that the fatty acid methyl esters (FAMEs or biodiesel) is obtained in 6–96% yields by using methanol to oil molar ratio of 36 in the presence of 6% of nanocatalysts containing melamine and guanine, respectively, at 160 °C within 3 h. The stability and reusability of the catalyst as well as the effect of reaction parameters on the FAME yield are described in this paper.     

Synthesis and catalytic application of Pd/PdO/Fe3O4@polymer-like graphene quantum dots

A novel approach was achieved for growing citric acid towards polymer-like graphene quantum dots (PGQD) with high efficiency in the presence of sodium hydroxide as a base catalyst. This protocol is completely safe, simple, fast, and efficient by a bottom up strategy. Thermal treatment of a mixture containing citric acid with NaOH at 300 °C gave PGQD during 5 min. The reaction afforded a new heterogeneous catalyst, Pd/PdO/Fe₃O₄@PGQD, in the presence of Pd and Fe₃O₄. The magnetically recoverable catalyst showed high activity in the oxidation of alkylarenes and alcohols using H₂O₂ as a green oxidant at room temperature. Comparison of the results with previous reports showed the efficiency of the catalyst to have high turnover numbers in mild reaction conditions.     

Photo-Fenton-like catalytic activity of nano-lamellar Fe2V4O13 in the degradation of organic pollutants

A new photo-Fenton-like catalyst with high activity, Fe₂V₄O₁₃, has been found. It can be obtained by a simple wet chemical process. The catalyst has a nano-lamellar structure with a thinness of less than 100 nm, a BET surface of 52.26 m² g^?1, and a band-gap of 1.59 eV favorable to absorption of visible light. Experiments demonstrated that Fe₂V₄O₁₃ could effectively catalyze degradation of Acid Orange II (AOII) by H₂O₂ in visible light. The degradation was well fitted by a simple pseudo-first-order reaction with a rate constant of 0.0965 min^?1. Moreover, the photo-Fenton-like catalytic activity of Fe₂V₄O₁₃ was much higher than that of not only α-Fe₂O₃ and V₂O₅ but also their mixture (Fe₂O₃ + 2V₂O₅) with an identical atomic ratio of Fe and V, and that of both Fe₃O₄ and γ-FeOOH. The high catalytic activity of Fe₂V₄O₁₃ possibly involves a special two-way Fenton-like, semiconductor photo-catalytic mechanism and the synergistic activation of Fe(III) and V(V) in Fe₂V₄O₁₃ towards H₂O₂.     

Enhanced reactivity in a heterogeneous oxido-peroxido molybdenum(VI) complex of salicylidene 2-picoloyl hydrazone in catalytic epoxidation of olefins

A molybdenum(VI) oxido-diperoxido complex of salicylidene 2-picoloyl hydrazine (sal-phz) was synthesized and successfully grafted onto chloro-functionalised Fe₃O₄ nanoparticles. The resulting heterogeneous and magnetically recoverable nanoscale catalyst MoO₃(sal-phz)/Fe₃O₄ was characterized by physicochemical and spectroscopic techniques. The activity of this heterogeneous catalyst for the oxidation of olefins to corresponding epoxides was efficiently increased by increasing the reaction temperature up to 95 °C. The nanocatalyst proved to be efficient for the selective epoxidation of a variety of alkenes using t-BuOOH with high conversion and selectivity. Leaching and recycling tests showed that the nanocatalyst can be reused at least six times without significant decrease in efficiency.     

Kinetics and reaction mechanism of isothermal oxidation of Iranian ilmenite concentrate powder

Thermal oxidation of commercial ilmenite concentrate from Kahnouj titanium mines, Iran, at 500–950 °C was investigated for the first time. Fractional conversion was calculated from mass change of the samples during oxidation. Maximum FeO to Fe₂O₃ conversion of 98.63 % occurred at 900 °C after 120 min. Curve fit trials together with SEM line scan results indicated constant-size shrinking core model as the closest kinetic mechanism of the oxidation process. Below 750 °C, chemical reaction with activation energy of 80.65 kJ mol^?1 and between 775 and 950 °C, ash diffusion with activation energy of 53.50 kJ mol^?1 were the prevailing mechanisms. X-ray diffraction patterns approved presence of pseudobrookite, rutile, hematite, and Fe₂O₃·2TiO₂ phases after oxidation of ilmenite concentrate at 950 °C.     

Synthesis and characterization of chitosan–polyvinylpyrrolidone–bovine serum albumin-coated magnetic iron oxide nanoparticles as potential carrier for delivery of tamoxifen

The proposed study examined the preparation of chitosan (CS)–polyvinylpyrrolidone (PVP)–bovine serum albumin (BSA)-coated magnetic iron oxide (Fe₃O₄) nanoparticles (Fe₃O₄–CS–PVP–BSA) to use as potential drug delivery carriers for delivery of tamoxifen drug (TAM) . The anticancer drug selected in this study was tamoxifen which can be used for the human breast cancer treatment. These prepared nanoparticles were characterized by FTIR, XRD, SEM, AFM, TEM, CD and VSM techniques. The swelling studies have been measured at different (10, 20, 30, 40, 50%) drug loading. The mean particle size of the tamoxifen-loaded nanoparticles system (Fe₃O₄–CS–TAM, Fe₃O₄–CS–TAM–PVP and Fe₃O₄–CS–TAM–PVP–BSA) as measured by Malvern Zetasizer ranged between 350 ± 2.3 and 601 ± 1.7 nm. As well as these drug-loaded nanoparticles were positively charged. The zeta potential was in the range of 28.9 ± 3.5 and 50.8 ± 3.9 mV. The encapsulation efficiency was between 63.60 ± 2.11 and 96.45 ± 2.12%. Furthermore, in vitro release and drug loading efficiency from the nanoparticles were investigated. The cytotoxicity of prepared nanoparticles was verified by MTT assay. In vitro release studies were executed in 4.0 and 7.4 pH media to simulate the intestinal and gastric conditions and different temperature (37 and 42 °C). Hence, the prepared tamoxifen-loaded nanoparticles system (Fe₃O₄–CS–TAM, Fe₃O₄–CS–TAM–PVP and Fe₃O₄–CS–TAM–PVP–BSA) could be a promising candidate in cancer therapy.     

Magneli phase Ti n O2n − 1 as corrosion-resistant PEM fuel cell catalyst support

Magneli phase titanium suboxide, Ti _n O_{2n ? 1}, with Brunauer–Emmett–Teller surface area up to 25 m² g^?1 was prepared using the heat treatment of titanium oxide (rutile) mixed with polyvinyl alcohol in ratios from 1:3 to 3:1. XRD patterns showed Ti₄O₇ as the major phase formed during the heat treatment process. The Ti _n O_{2n ? 1} showed excellent electrochemical stability in the potential range of ?0.25 to 2.75 V vs. standard hydrogen electrode. The Ti _n O_{2n ? 1} was employed as a polymer electrolyte membrane fuel cell catalyst support to prepare 20 wt% platinum (Pt)/Ti _n O_{2n ? 1} catalyst. A fuel cell membrane electrode assembly was fabricated using the 20 wt% Pt/Ti _n O_{2n ? 1} catalyst, and its performance was evaluated using H₂/O₂ at 80 °C. A current density of 0.125 A?cm^?2 at 0.6 V was obtained at 80 °C.     

Recyclable Fenton-like catalyst based on zeolite Y supported ultrafine,highly-dispersed Fe2O3 nanoparticles for removal of organics under mild conditions

The active Fenton-like catalyst, obtained by highly dispersed Fe₂O₃ nanoparticles in size of 5 nm on the surface of zeolite Y, shows the excellent degradation efficiency to phenol higher than 90% under the mild conditions of room temperature and neutral solution, and the catalyst can be easily recovered with stable catalytic activity for 8 cycles.     

Catalytic oxidation of NO over Mn–Co–Ce–Ox catalysts: effect of reaction conditions

Manganese–cobalt–cerium oxide (Mn–Co–Ce–Ox) catalysts were synthesized by the co-precipitation method and tested for activity in low-temperature catalytic oxidation of NO in the presence of excess O₂. With the best Mn–Co–Ce mixed-oxide catalyst, approximately 80 % NO conversion was achieved at 150 °C and a space velocity of 35,000 h^?1. The effect of reaction conditions (reaction temperature, volume fractions of NO and O₂, gas hourly space velocity (GHSV), and catalyst stability) was investigated. The optimum reaction temperature was 150 °C. Increasing the O₂ content above 3 % results in almost no improvement of NO oxidation. This catalyst enables highly effective removal of NO within a wide range of GHSV. Furthermore, the stability of the Me–Co–Ce–Ox catalyst was excellent; no noticeable decrease of NO conversion was observed in 40 h.     

Zeolite-supported silver and silver�Ciron nanoclusters and their activities as photodecomposition catalysts

Catalysts containing nanoclusters of Ag(I) and Fe₂O₃ as dopants with sodalite and Y zeolite supports have been investigated in order to develop a more efficient catalyst for photodecomposition of the pesticide carbaryl and to gain insight about the reaction mechanism. Ag(I)?Csodalite, Ag(I)/Fe₂O₃?Csodalite, Ag(I)?CY zeolite, and Ag(I)/Fe₂O₃?CY zeolite were synthesized by ion-exchange techniques and characterized by powder X-ray diffraction (XRD), solid-state luminescence, UV?Cvisible absorption, and atomic absorption spectroscopy measurements. The luminescence activity of the sodalite-supported and Y zeolite-supported catalysts was significantly different. Catalyst performance studies were conducted using carbaryl as the target compound and specific wavelengths of UV light as photon sources for the experiments. The studies showed that each catalyst??s performance was determined primarily by the specific wavelength of the UV light with which the system was irradiated. The studies also showed that inclusion of Fe₂O₃ as dopant enhanced the reactivity of the catalysts in several instances, with the Ag(I)/Fe₂O₃?Csodalite catalyst and 298 nm irradiation being the most reactive of the systems studied. Additional reactions using each catalyst and 298 nm irradiation, and including either sodium bicarbonate as hydroxyl radical scavenger or D₂O as solvent, showed that hydroxyl radicals were likely intermediates in the catalyzed photodecomposition reaction.     

Fe3O4 MNPs-DETA/Benzyl-Br3: A new magnetically reusable catalyst for the oxidative coupling of thiols

We report a new strategy to immobilize a bromine source on the surface of magnetic Fe₃O₄ nanoparticles (Fe₃O₄ MNPs-DETA/Benzyl-Br₃) leading to a magnetically recoverable catalyst, which exhibits high catalytic efficiency in oxidative coupling of thiols to the disulfides (89–98%). The Fe₃O₄ MNPs-DETA/Benzyl-Br₃ catalyst was fabricated by anchoring 3-chloropropyltrimethoxysilane (CPTMS) on magnetic Fe₃O₄ nanoparticles, followed with N-benzylation and reaction with bromine in tetrachloridecarbon. The resulting nanocomposite was analyzed by a series of characterization techniques such as FT-IR, SEM, TGA, VSM and XRD. The catalyst could be recovered via magnetic attraction and could be recycled at least 5 times without appreciable decrease in activity.     

Preparation of nanocrystalline BiFeO3 and kinetics of thermal process of precursor

The Bi₂Fe₂(C₂O₄)₅·5H₂O was synthesized by solid-state reaction at low heat using Bi(NO₃)₃·5H₂O, FeSO₄·7H₂O, and Na₂C₂O₄ as raw materials. The nanocrystalline BiFeO₃ was obtained by calcining Bi₂Fe₂(C₂O₄)₅·5H₂O at 600 °C in air. The precursor and its calcined products were characterized by thermogravimetry and differential scanning calorimetry, FT-IR, X-ray powder diffraction, and vibrating sample magnetometer. The data showed that highly crystallized BiFeO₃ with hexagonal structure [space group R3c(161)] was obtained when the precursor was calcined at 600 °C in air for 1.5 h. The thermal process of the precursor in air experienced five steps which involved, at first, the dehydration of an adsorption water molecule, then dehydration of four crystal water molecules, decomposition of FeC₂O₄ into Fe₂O₃, decomposition of Bi₂(C₂O₄)₃ into Bi₂O₃, and at last, reaction of Bi₂O₃ and Fe₂O₃ into hexagonal BiFeO₃. Based on Starink equation, the values of the activation energies associated with the thermal process of Bi₂Fe₂(C₂O₄)₅·5H₂O were determined. Besides, the most probable mechanism functions and thermodynamic functions (ΔS ^≠, ΔH ^≠, and ΔG ^≠) of thermal processes of Bi₂Fe₂(C₂O₄)₅·5H₂O were also determined.     

Synthesis of 14H-dibenzo xanthene derivatives using choline chloride/tin(II) chloride deep eutectic solvent and Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/ƛ-carrageenan/Zn(II)

In this study, various xanthene derivatives have prepared efficiently through a simple method using choline chloride/tin(II) chloride (ChCl·2SnCl₂) deep eutectic solvent (DES), alone, or in the presence of Fe₃O₄/?-carrageenan/Zn(II) magnetic bionanocatalyst. In the employed procedure, 2-naphthol derivatives have mixed with aromatic or aliphatic aldehydes and the reactions have been completed in the presence of DES at 90 °C in 1.5 h. In addition, using DES/Fe₃O₄/?-carrageenan/Zn(II), the reaction time was reduced to 30 min. The employed DES has been recycled four times without important loss of its activity.