Incorporation of extra amino acids in peptide recognition probe to improve specificity and selectivity of an electrochemical peptide-based sensor

We investigated the effect of incorporating extra amino acids (AA) at the n-terminus of the thiolated and methylene blue-modified peptide probe on both specificity and selectivity of an electrochemical peptide-based (E-PB) HIV sensor. The addition of a flexible (SG)₃ hexapeptide is, in particular, useful in improving sensor selectivity, whereas the addition of a highly hydrophilic (EK)₃ hexapeptide has shown to be effective in enhancing sensor specificity. Overall, both E-PB sensors fabricated using peptide probes with the added AA (SG-EAA and EK-EAA) showed better specificity and selectivity, especially when compared to the sensor fabricated using a peptide probe without the extra AA (EAA). For example, the selectivity factor recorded in the 50% saliva was ∼2.5 for the EAA sensor, whereas the selectivity factor was 7.8 for both the SG-EAA and EK-EAA sensors. Other sensor properties such as the limit of detection and dynamic range were minimally affected by the addition of the six AA sequence. The limit of detection was 0.5 nM for the EAA sensor and 1 nM for both SG-EAA and EK-EAA sensors. The saturation target concentration was ∼200 nM for all three sensors. Unlike previously reported E-PB HIV sensors, the peptide probe functions as both the recognition element and antifouling passivating agent; this modification eliminates the need to include an additional antifouling diluent, which simplifies the sensor design and fabrication protocol.     

Effect of redox label tether length and flexibility on sensor performance of displacement-based electrochemical DNA sensors

This article summarizes the sensor performance of four electrochemical DNA sensors that exploit the recently developed displacement-replacement sensing motif. In the absence of the target, the capture probe is partially hybridized to the signaling probe at the distal end, positioning the redox label, methylene blue (MB), away from the electrode. In the presence of the target, the MB-modified signaling probe is released; one type of probe is capable of assuming a stem-loop probe (SLP) conformation, whereas the other type adopts a linear probe (LP) conformation. Independent of the sensor architecture, all four sensors showed “signal-on” sensor behavior. Unlike the previous report, here we focused on elucidating the effect of the redox label tether length and flexibility on sensor sensitivity, specificity, selectivity, and reusability. For both SLP and LP sensors, the limit of detection was 10 pM for sensors fabricated using a signaling probe with three extra thymine (T3) bases linked to the MB label. A limit of detection of 100 pM was determined for sensors fabricated using a signaling probe with five extra thymine (T5) bases. The linear dynamic range was between 10 pM and 100 nM for the T3 sensors, and between 100 pM and 100 nM for the T5 sensors. When compared to the LP sensors, the SLP sensors showed higher signal enhancement in the presence of the full-complement target. More importantly, the SLP-T5 sensor was found to be highly specific; it is capable of discriminating between the full complement and single-base mismatch targets even when employed in undiluted blood serum. Overall, these results highlight the advantages of using oligo-T(s) as a tunable linker to control flexibility of the tethered redox label, so as to achieve the desired sensor response.     

Highly Sensitive Voltammetric Thrombin Aptamer Sensor Based on the Synergistic Effect of Doping/Depositing Gold Nanoparticles in Polydopamine Film

A highly sensitive square‐wave voltammetric thrombin (TB) aptamer sensor was developed using functional polydopamine (PD) film by doping and depositing gold nanoparticles into the bulk and the surface of PD. The aptamer sensor was fabricated by immobilizing a thiolated TB‐binding aptamer (TBA) on the AuNPs‐doped/deposited PD film. AuNPs‐supported methylene blue labels were used for the detection of human α‐TB. Under the optimized conditions, the aptamer sensor’s dynamic range and the detection limit were determined to be 2.0 pM–50 nM and 0.97±0.06 pM, respectively. Finally, the proposed aptamer sensor was successfully examined in human serum samples and satisfactory results were obtained.     

Determination of lead and cadmium in seawater using a vibrating silver amalgam microwire electrode

Silver amalgamated electrodes are a good substrate to determine lead (Pb) and cadmium (Cd) in seawater because they have properties similar to mercury but without the free mercury (Hg). Here a silver amalgamated microwire (SAM) electrode is optimised for the determination of Pb and Cd in coastal waters and uncontaminated ocean waters. The SAM was vibrated during the deposition step to increase the sensitivity, and electroanalytical parameters were optimised. The Hg coating required plating from a relatively concentrated (millimolar) solution, much greater (500×) than used for instance to coat glassy carbon electrodes. However, the coating on the ex situ amalgamated electrode was found to be stable and could be used for up to a week to determine trace levels of Pb in seawater of natural pH. The limit of detection square-wave ASV (50 Hz) using the pre-plated SAM electrode was 8 pM Pb using a 1-min plating time at pH 4.5. The limit of detection in pH 2 seawater was 4 pM using a 5-min plating time, and it was 12 pM using a 10-min plating time at natural pH in the presence of air, using a square-wave frequency of 700 Hz. The vibrating SAM electrode was tested on the determination of Pb in reference seawater samples from the open Atlantic (at the 20 pM level), Pacific, and used for a study of Pb in samples collected over 24 h in Liverpool Bay (Irish Sea).     

Designs of Enterobacteriaceae Lac Z Gene DNA Gold Screen Printed Biosensors

This paper describes specific electrochemical enterobacteriaceae lac Z gene DNA sensors based on immobilization of a thiolated 25 base single stranded probe onto disposable screen printed gold electrodes (gold SPEs). Two configurations have been evaluated. In the first one, the capture probe was attached to the electrode surface through its ? SH moiety, while mercaptohexanol (MCH) was used as spacer for the displacement of nonspecifically adsorbed oligonucleotide molecules. The hybridization event between the probe and target DNA sequences was detected at ?0.20 V by square‐wave voltammetry (SWV), using methylene blue (MB) as electrochemical indicator. The second genosensor configuration involved modification of gold high temperature SPEs with a 3,3′‐dithiodipropionic acid di(N‐succinimidyl ester) (DTSP) self‐assembled monolayer (SAM). Moreover, 2‐aminoethanol was used as blocking agent, and further modification with avidin allowed binding of the biotinylated enterobacteriaceae lac Z gene DNA probe. An enzyme amplified detection scheme was applied, based on the coupling of streptavidin‐peroxidase to the biotinylated complementary target, after the hybridization process, and immobilization of tetrathiafulvalene (TTF) as redox mediator atop the modified electrode. The amperometric response obtained at ?0.15 V after the addition of hydrogen peroxide was used to detect the hybridization process. Experimental variables concerning sensors composition and electrochemical transduction were evaluated in both cases. A better precision and reproducibility in the fabrication process, as well as a higher sensitivity were achieved using the biotinylated probe‐based sensor configuration. A limit of detection of 0.002 ng/μL was obtained without any preconcentration step.     

Enhanced sensitivity of self-assembled-monolayer-based SPR immunosensor for detection of benzaldehyde using a single-step multi-sandwich immunoassay

This paper describes the fabrication and sensing characteristics of a self-assembled monolayer (SAM)-based surface plasmon resonance (SPR) immunosensor for detection of benzaldehyde (BZ). The functional sensing surface was fabricated by the immobilization of a benzaldehyde–ovalbumin conjugate (BZ–OVA) on Au-thiolate SAMs containing carboxyl end groups. Covalent binding of BZ–OVA on SAM was found to be dependent on the composition of the base SAM, and it is improved very much with the use of a mixed monolayer strategy. Based on SPR angle measurements, the functional sensor surface is established as a compact monolayer of BZ–OVA bound on the mixed SAM. The BZ–OVA-bound sensor surface undergoes immunoaffinity binding with anti-benzaldehyde antibody (BZ-Ab) selectively. An indirect inhibition immunoassay principle has been applied, in which analyte benzaldehyde solution was incubated with an optimal concentration of BZ-Ab for 5 min and injected over the sensor chip. Analyte benzaldehyde undergoes immunoreaction with BZ-Ab and makes it inactive for binding to BZ–OVA on the sensor chip. As a result, the SPR angle response decreases with an increase in the concentration of benzaldehyde. The fabricated immunosensor demonstrates a low detection limit (LDL) of 50 ppt (pg mL⁻¹) with a response time of 5 min. Antibodies bound to the sensor chip during an immunoassay could be detached by a brief exposure to acidic pepsin. With this surface regeneration, reusability of the same sensor chip for as many as 30 determination cycles has been established. Sensitivity has been enhanced further with the application of an additional single-step multi-sandwich immunoassay step, in which the BZ-Ab bound to the sensor chip was treated with a mixture of biotin-labeled secondary antibody, streptavidin and biotin–bovine serum albumin (Bio–BSA) conjugate. With this approach, the SPR sensor signal increased by ca. 12 times and the low detection limit improved to 5 ppt with a total response time of no more than ca. 10 min. Figure A single-step multi-sandwich immunoassay step increases SPR sensor signal by ca. 12 times affording a low detection limit for benzaldehyde of 5 ppt     

Surface plasmon resonance-based immunosensor with oriented immobilized antibody fragments on a mixed self-assembled monolayer for the determination of staphylococcal enterotoxin B

An immunosensor based on surface plasmon resonance (SPR) with a mixed self-assembled monolayer (SAM) was developed to determine staphylococcal enterotoxin B (SEB). The SAM on a gold surface was fabricated by adsorbing a mixture of 16-mercapto-1-hexadecanoic acid (16-MHA) and hexanethiol at various molar ratios. Initially, full-length anti-SEB was randomly immobilized onto the SAM to form the immunosensing surface. Through optimization of surface functionalization and anti-SEB immobilization, the SPR sensors can be applied to the determination of SEB in a linear range of 0.01?~?1.0 μg.mL^?1. Furthermore, a smaller antibody fragment (F(ab)’) was generated and immobilized randomly (via amino groups) or in an oriented manner (via ?SH groups) to form the immunosensing surface. The oriented immobilization of F(ab)’ led to a 50% increase in the antigen binding efficiency compared to randomly immobilized covalent F(ab’) fragments. The resulting calibration curve showed higher sensitivity. In addition, the specificity and applicability of the proposed immunosensor to milk samples were also demonstrated. Furthermore, the sensor can be regenerated using 0.1 M HCl, and 70% of the initial response was maintained over 3 cycles.     

The synthesis of graphene oxide covalently linked with nickel tetraamino phthalocyanine: A photoelectrochemical sensor for the analysis of rifampicin irradiated with blue light

In this article, the fabrication and characterization of a photoelectrochemical (PEC) rifampicin sensor based on graphene oxide grafted with Ni tetraamino phthalocyanine was described, which presents an excellent PEC activity, sensitivity, and material stability. The synthesized graphene oxide grafted with Ni tetraamino phthalocyanine was characterized using ultraviolet–visible (UV–vis), Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) analyses. Specifically, detection for rifampicin was based on the reduction of photocurrent caused by binding of the analyte to the sensing electrode surface. The fabricated sensor was characterized in a broad linear response range (0.025–71.3 μM) and with a low detection limit (2.5 nM), outperforming the previously reported sensors and thus being well suited for quality control and other applications, as confirmed by successful real‐life sample testing.     

Anodic stripping voltammetric determination of copper (II) ions at a graphene quantum dot-modified pencil graphite electrode

A simple and sensitive electrochemical sensor based on graphene quantum dot-modified pencil graphite electrode (GQD/PGE) was fabricated and used for highly selective and sensitive determination of copper (II) ions in nanomolar concentration by square wave adsorptive stripping voltammetric method. The sensing mechanism could be attributed to the formation of a complex between Cu²⁺ ions and oxygen-containing groups in GQDs which result in an increased SWV signal in comparison with the bare electrode. Optimization of various experimental parameters such as pre-concentration time, pre-concentration potential, pH, and buffer type which influence the performance of the sensor, was investigated. Under optimized condition, GQD-modified electrode has been used for the analysis of Cu²⁺ in the concentration range from 50 pM to 4 nM and a lower detection limit of 12 pM with good stability, repeatability, and selectivity. Finally, the practical applicability of GQD-PGE was confirmed via measuring trace amount of Cu (II) in water samples. The GQD/PGE surface could be regenerated by exerting more positive potentials than the stripping potential of the Cu (II) ion and then used for another deposition.     

Rapid fabrication of electrochemical enzyme sensor chip using polydimethylsiloxane microfluidic channel

Applicability of polydimethylsiloxane (PDMS) for easy and rapid fabrication of enzyme sensor chips, based on electrochemical detection, is examined. The sensor chip consists of PDMS substrate with a microfluidic channel fabricated in it, and a glass substrate with enzyme-modified microelectrodes. The two substrates are clamped together between plastic plates. The sensor chip has shown no leakage around the microelectrodes under continuous solution flow (34 μl/min). Amperometric response of the sensor chips developed in this work suggest that various types of enzyme sensors can be designed by using PDMS microfluidic channels.     

Single Conducting Polymer Nanowire Based Sequence‐Specific,Base‐Pair‐Length Dependant Label‐free DNA Sensor

We have fabricated a highly sensitive, simple and label‐free single polypyrrole (Ppy) nanowire based conductometric/chemiresistive DNA sensor. The fabrication was optimized in terms of probe DNA sequence immobilization using a linker molecule and using gold‐thiol interaction. Two resultant sensor designs working on two different sensing mechanisms (gating effect and work function based sensors) were tested to establish reliable sensor architecture with higher sensitivity and device‐to‐device reproducibility. The utility of the work function based configuration was demonstrated by detecting 19 base pair (bp) long breast cancer gene sequence with single nucleotide polymorphism (SNP) discrimination with high sensitivity, lower detection limit of ∼10⁻¹⁶ M and wide dynamic range (∼10⁻¹⁶ to 10⁻¹¹ M) in a small sample volume (30 µL). To further demonstrate the utility of the DNA sensor for detection of target sequences with different number of bases, targets with 21 and 36 bases were detected. These sequences have implications in environmental sample analysis or metagenomics. Sensor response showed increase with the number of bases in the target sequence. For long sequence (with 36 bases), effect of DNA alignment on sensor performance was studied.     

Highly sensitive and reproducible cyclodextrin-modified gold electrodes for probing trace lead in blood

A highly sensitive and reproducible lead sensor based on a cyclodextrin-modified gold electrode was created. A self-assembled monolayer (SAM) of thiolated β-cyclodextrin (6-(2-mercapto-ethylamino)-6-deoxy-β-cyclodextrin (MEA-β-CD)) was prepared and modified on a gold electrode (MCGE) for specific Pb²⁺-sensing. Thus the mercury-free sensors for Pb²⁺ assay based on MCGE were established. A linear calibration response for Pb²⁺ was found in the range of 1.7 × 10⁻⁸ M to 9.3 × 10⁻⁷ M. The detection limit was 7.1 × 10⁻⁹ M (with S/N > 3), which was 10 times lower than other reported methods of detection Pb²⁺ with CD. The measurement results via this method for real blood samples were well agree with those obtained by ICP-AES, and thus presented a novel strategy in design of specific lead sensors with high sensitivity and stability for analysis of trace Pb²⁺ in real blood samples.     

A lead(II) sensor based on a glassy carbon electrode modified with Fe3O4 nanospheres and carbon nanotubes

We have developed a highly sensitive and selective sensor for lead(II) ions. A glassy carbon electrode was modified with Fe₃O₄ nanospheres and multi-walled carbon nanotubes, and this material was characterized by scanning electron microscopy and X-ray diffraction. The electrode displays good electrochemical activity toward Pb(II) and gives anodic and cathodic peaks with potentials at ?496 mV and ?638 mV (vs. Ag/AgCl) in pH?6.0 solution. The sensor exhibits a sensitive and fairly selective response to Pb(II) ion, with a linear range between 20 pM and 1.6 nM, and a detection limit as low as 6.0 pM (at a signal-to noise ratio of 3). The sensor was successfully applied to monitor Pb(II) in spiked water samples.

Gold nanoparticles chemisorbed by a terphenyldithiol self-assembled monolayer for fabrication of a protein biosensor

In this study, improved detection of bovine serum albumin (BSA) was achieved by use of a fabricated surface plasmon resonance (SPR) biosensor. Terphenyldithiol (TPDT) was self-assembled on a gold substrate, then gold nanoparticles (Au-NPs) were chemisorbed on to the TPDT monolayer by strong bonding with the terminal thiol groups of the TPDT. The new sensor obtained was tested for immobilization of protein. The SPR results revealed much better detection of BSA by Au-NPs chemisorbed on the TPDT self-assembled monolayer (SAM) than by the bare SAM on the gold substrate.     

Development of an optical chemical sensor based on 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol in Nafion for determination of nickel ion

An optical chemical sensor based on immobilization of 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol (Br-PADAP) in Nafion membrane is described. The membranes were cast onto glass substrates and were used for the determination of nickel in aqueous solutions by spectrophotometry. The sensor system is highly transparent, mechanically stable and showed no evidence of reagent leaching. The influence of several parameters such as pH, ligand concentration, and type and concentration of regenerating solution were optimized. The sensor system showed good sensitivity in the range 0.5-20 μg ml⁻¹ with a detection limit of 0.3 μg ml⁻¹ Ni(II). The sensor has been incorporated into a home-made flow-through cell for determination of nickel in flowing streams with improved sensitivity, precision and detection limit. The calibration curve in the flow system was linear in the range 0.1-16 μg ml⁻¹ with a detection limit of 0.07 μg ml⁻¹. The sensor is easily regenerated by dilute nitric acid solution. The proposed method was successfully applied to the determination of nickel content in vegetable oil and chocolate samples and the results were compared with those obtained using atomic absorption spectrometry.     

Highly sensitive hydrazine chemical sensor based on mono-dispersed rapidly synthesized PEG-coated ZnS nanoparticles

Monodispersed PEG-coated ZnS (P-ZnS) nanoparticles (NPs) were synthesized by facile microwave process and utilized as efficient electron mediators for the fabrication of highly sensitive hydrazine chemical sensor. The detailed morphological and structural properties revealed the monodispersity and good crystallinity for synthesized P-ZnS NPs. A high-sensitivity of ∼89.3 μA cm⁻² μM and low limit of detection of 1.07 μM, based on S/N ratio, were obtained for the fabrication of hydrazine chemical sensor based on P-ZnS NPs. To the best of our knowledge, this is the first report which demonstrates the utilization of P-ZnS NPs for the fabrication of efficient hydrazine chemical sensor. By this work, it could be concluded that simply synthesized ZnS NPs can be used as efficient electron mediators for the fabrication of effective hydrazine chemical sensors.     

Electrocatalytic sensor devices: (I) cyclopentadienylnickel(II) thiolato Schiff base monolayer self-assembled on gold

The fabrication of a self-assembled monolayer (SAM) of a cyclopentadienylnickel(II) thiolato Schiff base compound, [Ni(SC₆H₄NC(H)C₆H₄OCH₂CH₂SMe)(η⁵-C₅H₅)]₂ on a gold electrode is described. Effective electronic communication between the Ni(II) centres and the gold surface was established by electrochemically cycling the Schiff base-doped Au electrode in 0.1 M NaOH from −200 mV to +600 mV. The SAM-modified electrode exhibited quasi-reversible electrochemistry. The integrity of this electrocatalytic SAM, with respect to its ability to block and electro-catalyse certain Faradaic processes, was interrogated using cyclic voltammetric experiments. The formal potential, E°′, varied with pH to give a slope of about −30 mV pH⁻¹. The surface concentration, G, of the nickel redox centres was found to be 1.548×10⁻¹¹ mol cm⁻². By electrostatically doping the SAM using an applied potential of +700 mV versus Ag/AgCl, in the presence of horseradish peroxidase (HRP), it was fine-tuned for amperometric determination of H₂O₂. The electrocatalytic-type biosensor displayed typical Michaelis-Menten kinetics and the limit of detection was found to be 6.25 mM.     

Demonstration of a simple, economical and practical technique utilising an imprinted polymer for metal ion sensing

This paper describes a simple, economical and practical optical sensor that has been developed using an ion imprinted polymer for detecting copper(II) ion using reflectance spectrometry. The imprinted polymer was synthesised in the presence of copper(II) ion using 4-vinylpyridine as monomer, 2-hydroxyethyl methacrylate as co-monomer, and ethylene glycol dimethacrylate as cross-linker in methanol via free radical polymerisation. The polymer formed was physically ground into fine particles, fabricated into a sensor probe and attached at the tip of an optical fibre bundle. The sensor operates optimally at pH 5 under constant stirring condition and has a linear dynamic range for copper(II) ion determination of 0.4–4.0 mM. The limit of detection for the sensor was 123 µM. The sensor has high selectivity for monitoring copper (II) ion in a multi-analyte environment, while also exhibiting better sensitivity compared to non-imprinted polymer. The response of the sensor can be regenerated fully without significant loss in its analytical signal for re-use. This reduces the consumable cost and at the same time making the operational process of such sensor simpler and more practical to be employed in real applications.     

有序介孔碳/石墨烯/镍泡沫的制备及其对多巴胺的高灵敏度和高选择性检测

柔性生物传感器在可穿戴电子设备中有着广泛的应用前景. 为了获得柔性电化学多巴胺传感器,作者在本工作中首先在镍泡沫表面通过化学气相沉积生长石墨烯,随后通过高温碳化嵌段共聚物与酚醛树脂在石墨烯表面共组装形成的薄膜制备了有序介孔碳/石墨烯/镍泡沫（OMC/G/Ni）复合材料. 其中,镍泡沫可以为复合材料提供具有高导电性和良好柔韧性的金属骨架,而具有垂直排列介孔阵列的有序介孔碳层为复合材料提供了高的电活性表面积,且有利于活性位点的暴露. 值得注意的是,夹在有序介孔碳层和镍泡沫之间的石墨烯极大地增强了各组分之间的相容性,有利于进一步提升复合材料的电化学性能. 作为电化学传感器中的工作电极,OMC/G/Ni体现出优异的多巴胺检测能力. 不但具有宽的线性检测范围（0.05 ~ 58.75 μmol·L^-1）和低检测限（0.019 μmol·L^-1）,还具有良好的选择性、重现性和稳定性. 此外,OMC/G/Ni在弯曲状态下依旧能够保持对多巴胺的高检测能力,证明了其在柔性生物传感器中的应用潜力.     

Ultra-sensitive hydrazine chemical sensor based on high-aspect-ratio ZnO nanowires

High-aspect-ratio ZnO nanowires based ultra-sensitive hydrazine amperometric sensor has been fabricated which showed a high and reproducible sensitivity of 12.76 μA cm⁻² nM⁻¹, detection limit, based on S/N ratio, 84.7 nM, response time less than 5 s, linear range from 500 to 1200 nM and correlation coefficient of R = 0.9989. This is the first report in which such a very high-sensitivity and low detection limit has been achieved for the hydrazine sensors by using ZnO nanostructures modified electrodes. Therefore, this work opens a way to utilize simply grown ZnO nanostructures as an efficient electron mediator to fabricate efficient hydrazine sensors.