底部局部加热多孔介质自然对流传热的格子Boltzmann模拟

运用格子Boltzmann方法研究了底部局部加热多孔介质方腔的自然对流传热.方腔的上壁面为低温热源,下壁面为局部高温热源,左右壁面为绝热条件.重点分析了高温热源位置a及尺寸b对多孔介质方腔自然对流传热性能的影响,提出了平均Nusselt数Nu和位置a及尺寸b的拟合关系式.研究结果表明:高温热源位置及尺寸对多孔介质方腔内自然对流传热性质的影响很大,且存在最佳高温热源位置(a=4/16)和尺寸(b=0.75),以达到最强的对流换热强度(Nu_(max)≈10.35)和最大的对流换热量(Q_(max)≈5.69).     

倾斜度及温度震荡频率对三维多孔介质方腔自然对流换热的影响

对三维多孔介质倾斜方腔内非稳态自然对流换热进行数值研究.腔体右壁面(X=1)保持恒温T₀,左壁面(X=0)基于温度T₀按正弦规律变化,其他所有壁面保持绝热.采用Brinkman扩展达西模型及SIMPLE算法模拟方腔内的流动.方腔沿y轴转动倾角α1的变化范围为0°~90°,沿x轴转动倾角α2的变化范围为0°~45°,无量纲温度震荡频率f的变化范围为5π~90π.详细研究倾角和温度震荡频率对三维方腔自然对流换热的影响.计算结果表明:当倾角α1=46°,α2=45°及温度震荡频率f=45π时,方腔内的换热最强.     

方腔内竖直板混合对流换热的数值模拟

对方腔内竖直板的层流混合对流换热进行了数值模拟.结果表明,竖直板处于水平方向两个不同位置时,竖直板背风面的混合对流换热量大于纯自然对流换热量.送风口高度比取0.667、0.767时,竖直板背风面的混合对流换热量大于纯自然对流换热量.当送风口高度比为0.167～0.467、0.767～0.867区间内,流动与换热得到定常解.在送风口高度比大于0.467小于0.767范围内,流动与换热为非定常解.     

局部热壁面多孔介质方腔内自然对流的数值研究

本文对上下壁面绝热、左侧壁面长度为b的嵌装加热器部分维持恒定温度T_h而剩余部分绝热,且右侧壁面维持恒定温度T_c的多孔介质方腔内的自然对流换热进行了数值研究.在热壁面无量纲长度B=0.5(B=b/L)的条件下,综合研究了左侧壁面受热部分中心距上壁面的无量纲长度D(D=d/L)、Da数、Ra数和孔隙率对腔体内自然对流换热的影响.数值计算结果表明,左侧壁面受热部分位置的不同对腔体内自然对流换热有很大的影响,D在0.6附近取值时,Na数最大.Da数、Ra数对腔体的自然对流换热影响较大,而孔隙率对换热的影响较小.     

方腔驱动流的数值模拟研究

利用CFD软件对方腔的温度场和速度场进行了数值模拟计算。采用有限元法对模型的连续性方程、动量方程和能量方程进行离散。对方腔内的流体受迫对流换热进行数值模拟,主要分析了方腔顶部流体在不同速度的情况下,对方腔内部流体的温度场和速度场以及对流换热量的影响,结果表明随着方腔顶部流速的增大方腔底部的温度场和换热量也增大。     

三维方腔内竖直平板混合对流换热的数值研究

本文建立了三维方腔内竖直板混合对流换热的数学模型,探讨Re数,进风口位置、竖直板位置对混合对流换热的影响.结果表明:随Re数增加,竖直板下部的平均Nu2下降,而总体平均Nu1增加.随送风口高度增加,竖直板对流换热量增加.在竖直板位置L1/H=0.5～1.5的范围内,竖直板处于中间位置L1/H=1.0时,竖直板混合对流换...     

倾斜多孔介质方腔内纳米流体自然对流的格子Boltzmann方法模拟

利用格子玻尔兹曼方法 (lattice Boltzmann method, LBM) 对倾斜多孔介质方腔内 Al_2O_3-H_2O 纳米流体的自然对流进行数值模拟, 考虑了孔隙率 (0.3 ≤?≤ 0.9)、瑞利数 (10~3 ≤ Ra ≤ 10~6)、纳米颗粒体积分数(0 ≤ ? ≤ 0.04) 和倾斜角 (0°≤γ≤ 120°) 等因素的影响, 研究了正弦温度分布边界条件下倾斜多孔介质方腔内纳米流体的自然对流传热机理. 结果表明: 若?和γ保持不变时, 随着 Ra 数的增大, 热壁面处的平均努塞尔数 (Nu_(ave) 数) 呈现出先减小后增大的趋势; 对于给定的 Ra 数, 当γ = 0°时, 随着孔隙率的增大, 热壁面处Nu_(ave) 数逐渐增大, 当γ = 40°, 80°和 120°时, Nuave 数在?= 0.7 左右时达到最大值; 若?和 Ra 数保持不变, 当γ = 40°时, 方腔内的自然对流换热效率最强, 当γ = 80°时热壁面自然对流换热效率被削弱. 最后, 研究了纳米颗粒体积份数的影响, 当方腔施加一定倾角时, 热壁面处的 Nuave 数随着纳米颗粒体积分数的增大而增大.     

研究冷却规律实验的新方法

通常将对流分为自然对流和强迫对流．在自然对流时，发热体周围流体介质的流动，主要是因为在各处温度不同情况下密度不同而引起的；在强迫对流时，热体周围介质主要凭借外加气泵成风扇的作用来维持流动．在稳态时，热体因对流而散失的热量可由下式来表示其中散热率兰表示热体在单位时间内所散失的热量，人为周围流体的温度，在空气中就是室温．E是与热体的表面积、表面状态、周围空气的状态和性质等有关的系数．m值在自然对流时为m=5／4=1.25．本文介绍一种新的实验方法，在稳态时，通过直接测量散热率，来确定m值和E值．下图为实验装置图…     

周期性边界条件下多孔介质方腔内自然对流换热数值研究

对充满多孔介质的倾斜方腔,在其上下壁面绝热、右侧壁面维持恒温To及左侧壁面温度基于To随时间按正弦规律变化的情况下,采用Brinkman扩展达西模型和SIMPLER算法对方腔内的自然对流与换热进行了非稳态数值模拟,方腔倾角α的范围为0°～90°,Pr数为1,Ra数为106.计算研究不同的振荡频率和方腔倾角对方腔内对流换热的影响.数值模拟结果表明:振荡频率f为60π,方腔倾角为43°时,方腔内的换热最强.     

布朗运动影响下方腔内纳米流体非稳态自然对流的数值研究

对方腔一侧壁面温度随时间按正弦规律变化、充满CuO-水纳米流体的二维方腔内的非稳态自然对流换热进行了数值研究。在相关参数一定的条件下,研究了Ra数、纳米颗粒体积份额φ和纳米颗粒布朗运动对自然对流换热特性的影响。数值模拟结果表明:考虑布朗运动时壁面时均Nu数均大于不考虑布朗运动时的相应值;不考虑布朗运动时,时均Nu数均随φ的增大而增大;而考虑布朗运动时,当Ra数较小时,时均Nu数均随φ的增大而增大,而Ra数较大时,存在有最佳的φ值,可使时均Nu数达到最大值。     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.