Chemical synthesis of nanocrystalline SnO2 thin films for supercapacitor application

Nanocrystalline SnO₂ thin films were deposited by simple and inexpensive chemical route. The films were characterized for their structural, morphological, wettability and electrochemical properties using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy techniques (SEM), transmission electron microscopy (TEM), contact angle measurement, and cyclic voltammetry techniques. The XRD study revealed the deposited films were nanocrystalline with tetragonal rutile structure of SnO₂. The FT-IR studies confirmed the formation of SnO₂ with the characteristic vibrational mode of Sn-O. The SEM studies showed formation of loosely connected agglomerates with average size of 5-10 nm as observed from TEM studies. The surface wettability showed the hydrophilic nature of SnO₂ thin film (water contact angle 9°). The SnO₂ showed a maximum specific capacitance of 66 F g⁻¹ in 0.5 Na₂SO₄ electrolyte at 10 mV s⁻¹ scan rate.     

Intercalation of lithium ions into bulk and powder highly oriented pyrolytic graphite

The electrochemical reactions of highly oriented pyrolytic graphite (HOPG) bulk and powder electrodes in 1 M LiPF₆ 1:1 EC/DMC solution were investigated and the results show that the intercalation reaction of lithium ion into HOPG electrode occurs only at the edge plane and SEI formation reaction on the basal plane is negligible in comparison with that on the edge plane. The active surface area of HOPG powder electrode could be deduced by comparing the peak area (consumed charge for SEI formation) at potential of 0.5 V on voltammograms with that of bulk HOPG edge electrode. The diffusion coefficients of lithium ion in HOPG bulk layers and in HOPG powder was for the first time measured by use of electrochemical impedance spectra and potential step chronamperameter methods. It was found that the diffusion coefficients of lithium in HOPG were in the range of 10⁻¹¹-10⁻¹² cm² s⁻¹ for the lithium-HOPG intercalation compounds at potentials from 0.2 (vs. Li/Li⁺) to 0.02 V, decreasing with the increase of lithium intercalation degree. A good agreement was obtained between the results from bulk and powder HOPG electrodes by electrochemical impedance spectra method.     

Poly(3-methylthiophene)-based porous silicon substrates as a urea-sensitive electrode

Poly(3-methylthiophene) (P3MT)-based porous silicon (PS) substrates were fabricated and characterized by cyclic voltammetry, scanning electron microscopy, and auger electron spectroscopy. After doping urease (Urs) into the polymeric matrix, sensitivity and physicochemical properties of the P3MT-based PS substrate was investigated compared to planar silicon (PLS) and bulk Pt substrates. PS substrate was formed by electrochemical anodization in an etching solution composed of HF, H₂O, and ethanol. Subsequently, Ti and Pt thin-films were sputtered on the PS substrate. Effective working electrode area (A_eff) of the Pt-deposited PS substrate was determined from a redox reaction of Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ redox couple in which nearly reversible cyclic voltammograms were obtained. The i_p versus v^1/2 plots showed that A_eff of the PS-based Pt thin-film electrode was 1.62 times larger than that of the PLS-based electrode.Electropolymerization of P3MT on both types of electrodes were carried out by the anodic potential scanning under the given potential range. And then, urease molecules were doped to the P3MT film by the chronoamperometry. Direct electrochemistry of a Urs/P3MT/Pt/Ti/PS electrode in an acetonitrile solution containing 0.1 mol/L NaClO₄ was introduced compared to a P3MT/Pt/Ti/PS electrode at scan rates of 10 mV s⁻¹, 50 mV s⁻¹, and 100 mV s⁻¹.Amperometric sensitivity of the Urs/P3MT/Pt/Ti/PS electrode was ca. 1.67 μA mM⁻¹ per projected unit square centimeter, and that of the Urs/P3MT/Pt/Ti/PLS electrode was ca. 1.02 μA mM⁻¹ per projected unit square centimeter in a linear range of 1-100 mM urea concentrations. 1.6 times of sensitivity increase was coincident with the results from cyclic voltammetrc analysis.Surface morphology from scanning electron microscopy (SEM) images of Pt-deposited PS electrodes before and after the coating of Urs-doped P3MT films showed that pore diameter and depth were 2 μm and 10 μm, respectively. Multilayered-film structures composed of metals and organics for both electrodes were also confirmed by auger electron spectroscopy (AES) depth profiles.     

Rational synthesis of α-MnO2 and γ-Mn2O3 nanowires with the electrochemical characterization of α-MnO2 nanowires for supercapacitor

An acidification-hydrothermal method was developed to synthesize α-MnO₂ nanowires, which was subsequently treated with ethanol, resulting in γ-Mn₂O₃ nanowire bundles on a large scale. The electrochemical characterization was carried out by cyclic voltammetry, which indicated that the α-MnO₂ nanowires in 0.5 mol L⁻¹ Na₂SO₄ aqueous electrolyte was of an excellent electrode material for supercapacitor at the scan rate of 10 mV S⁻¹ in the range of 0.0-0.85 V.     

Porous LiNi0.75Co0.25O2 microspheres prepared via a hydrothermal process as cathode material for lithium ion batteries

Porous LiNi_0.75Co_0.25O₂ microspheres are successfully prepared by a simple hydrothermal process by using H[Ni_0.75Co_0.25OOH]₃ and LiOH as starting materials in the presence of urea for the first time. The synthesized samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), specific surface area (S_BET), and electrochemical performance. The synthesized LiNi_0.75Co_0.25O₂ has a good electrochemical performance with an initial discharge capacity of 169.3 mA g⁻¹ and good capacity retention of 96.7% after 50 cycles at 0.2 C (25 mA g⁻¹). The electrochemical lithium ion insertion/extraction process is quite reversible even at 5 C. Furthermore, the structure in the charge-discharge process is stable and the impedance increased slowly during cycling.     

CO_2活化温度对N-C复合碳气凝胶结构及电化学性能的影响

采用CO2活化工艺对氮掺杂碳气凝胶(N-CA)的结构进行重整,并系统研究了活化温度对活化氮掺杂碳气凝胶(N-ACA)孔结构及电化学性能的影响。利用N2吸附数据、X-光电子能谱(XPS)和元素分析对样品的结构及元素组成进行表征。结果表明,随活化温度的升高,N-ACA的比表面积逐渐增大,其含有的氮原子分数逐渐减少,吡咯氮含量明显增加。利用循环伏安(CV)、电化学阻抗谱(EIS)等测试技术评价了碳气凝胶样品在6mol·L-1 KOH电解液中的电化学性能,结果发现,合理的孔结构与较高的吡咯氮含量是影响电容器比容量的关键因素。在5mV·s-1扫描速率下测试950-N-ACA电极的比电容值高达267.4F·g-1,经1000次充放电后比电容损失值在1.5%以内。     

Template-free synthesis of MnO2 nanowires with secondary flower like structure: Characterization and supercapacitor behavior studies

Manganese dioxide (MnO₂) nanowires with diameter about 30-70 nm is achieved via a two-step process: first, template-free cathodic electrodeposition from aqueous solution of Mn(NO₃)₂ on steel substrate and followed by heat treatment. The temperature-annealed sample was studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) methods and Fourier transform infrared (FT-IR) spectroscopy. The electrochemical performance of the MnO₂ sample was studied by cyclic voltammetry (CV) and chronopotentiometry in Na₂SO₄ solutions. The sample showed excellent supercapacitive behavior. The specific capacitance (SC) of 237 F g⁻¹ in a potential window of 0-0.9V was obtained at the scan rate of 2 mV s⁻¹. The SC calculated from the chronopotentiometry data is about 246 F g⁻¹. The SC was decreased by 16% after 1000 cycles.     

Cationic starch as a precursor to prepare porous activated carbon for application in supercapacitor electrodes

Three activated carbons (ACs) for the electrodes of supercapacitor were prepared from cationic starch using KOH, ZnCl₂ and ZnCl₂/CO₂ activation. The BET surface area, pore volume and pore size distribution of the ACs were evaluated using density functional theory method, based on N₂ adsorption isotherms at 77 K. The surface morphology was characterized with SEM. Their electrochemical performance in prototype capacitors was determined by galvanostatic charge/discharge characteristics and cyclic voltammetry, and compared with that of a commercial AC, which was especially prepared for use in supercapacitors. The KOH-activated starch AC presented higher BET surface area (3332 m² g⁻¹) and larger pore volume (1.585 cm³ g⁻¹) than those of the others, and had a different surface morphology. When used for the electrodes of supercapacitors, it exhibited excellent capacitance characteristics in 30 wt% KOH aqueous electrolytes and showed a high specific capacitance of 238 F g⁻¹ at 370 mA g⁻¹, which was nearly twice that of the commercial AC.     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.     

Potato starch-based activated carbon spheres as electrode material for electrochemical capacitor

Potato starch-based activated carbon spheres (PACS) were prepared from potato starch by stabilization, carbonization followed by activation with KOH. The obtained PACS are hollow and retain the original morphology of potato starch with decrease in size, as shown by scanning electron microscopy. Modification of textural properties of the PACS was achieved by varying the carbonization temperature and the ratio of KOH/PCS. The results of N₂ adsorption isotherms indicate that the samples prepared are mainly microporous. The electrochemical behaviors of the hollow PACS were studied by galvanostatic charge-discharge, cyclic voltammetry, and impedance spectroscopy. The results indicate that high specific capacitance of 335 F/g is obtained at current density 50 mA/g for PACS with specific surface area 2342 m²/g. Only a slight decrease in capacitance, to 314 F/g, was observed when the current density increases to 1000 mA/g, indicating a stable electrochemical property.     

Preparation of alkaline solid polymer electrolyte based on PVA-TiO2-KOH-H2O and its performance in Zn-Ni battery

A novel composite alkaline polymer electrolyte based on poly(vinyl alcohol) (PVA) polymer matrix, titanium dioxide (TiO₂) ceramic fillers, KOH, and H₂O was prepared by a solution casting method. The properties of PVA-TiO₂-KOH alkaline polymer electrolyte films were studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and AC impedance techniques. DSC and XRD results showed that the domain of amorphous region in the PVA polymer matrix augmented when TiO₂ filler was added. The SEM result showed that TiO₂ particles dispersed into the PVA matrix although some TiO₂ aggregates of several micrometers were formed. The alkaline polymer electrolyte showed excellent electrochemical properties. The room temperature (20 °C) ionic conductivity values of typical samples were between 0.102 and 0.171 S cm⁻¹. The Zn-Ni secondary battery with the alkaline polymer electrolyte PVA-TiO₂-KOH had excellent electrochemical property at the low charge-discharge rate.     

DNA hybridization and phosphinothricin acetyltransferase gene sequence detection based on zirconia/nanogold film modified electrode

This study reports a novel electrochemical DNA biosensor based on zirconia (ZrO₂) and gold nanoparticles (NG) film modified glassy carbon electrode (GCE). NG was electrodeposited onto the glassy carbon electrode at 1.5 V, and then zirconia thin film on the NG/GCE was fabricated by cyclic voltammetric method (CV) in an aqueous electrolyte of ZrOCl₂ and KCl at a scan rate of 20 mV/s. DNA probes were attached onto the ZrO₂/NG/GCE due to the strong binding of the phosphate group of DNA with the zirconia film and the excellent biocompatibility of nanogold with DNA. CV and electrochemical impedance spectroscopy (EIS) were used to characterize the modification of the electrode and the probe DNA immobilization. The electrochemical response of the DNA hybridization was measured by differential pulse voltammetry (DPV) using methylene blue (MB) as the electroactive indicator. After the hybridization of DNA probe (ssDNA) with the complementary DNA (cDNA), the cathodic peak current of MB decreased obviously. The difference of the cathodic peak currents of MB between before and after the hybridization of the probe DNA was used as the signal for the detection of the target DNA. The sequence-specific DNA of phosphinothricin acetyltransferase (PAT) gene in the transgenic plants was detected with a detection range from 1.0 × 10⁻¹⁰ to 1.0 × 10⁻⁶ mol/L, and a detection limit of 3.1 × 10⁻¹¹ mol/L.     

Effects of carbonization temperature on microstructure and electrochemical performances of phenolic resin-based carbon spheres

Activated phenol resin-based carbon spheres (APCS) electrodes with high double layer capacitance and good rate capability were prepared from phenol resin-based spheres (PS) at different carbonization temperatures prior to KOH activation. The carbonization temperature has a marked effect on both the pore structure and the electrochemical performances of the APCS in 6 M KOH electrolyte. APCS carbonized at 600 °C results in higher specific surface area and larger pore size, and hence higher capacitance and better rate capability. The specific capacitance of the APCS in 6 M KOH aqueous solution can be as high as 282 F g⁻¹. It remains 252 F g⁻¹ as the current density increases to 1000 mA g⁻¹.     

Synthesis and characterization of ZnCo2O4 nanomaterial for symmetric supercapacitor applications

ZnCo₂O₄ nanomaterial was prepared by co-precipitation method and characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), and galvanostatic charge–discharge tests at various current densities. It is shown that the crystal structure and surface morphology play an important role in the enhancement of the specific capacitance. The TEM results clearly indicate that the prepared material shows aggregated particles. The particle size powder was about 50 nm, and SEM pictures indicate a porous morphology. The electrochemical behavior of ZnCo₂O₄ was characterized by mixing equal proportion of carbon nanofoam (CNF). From CV, it is concluded that the combination of redox and pseudo-capacitance increases the specific capacitance up to 77 F g⁻¹ at 5 mV s⁻¹ scan rate. The ZnCo₂O₄-based supercapacitor cell has good cyclic stability and high coulombic efficiency.     

Synthesis of spherical LiFePO4/C via Ni doping

Spherical LiFePO₄/C powders were synthesized by the conventional solid-state reaction method via Ni doping. Low-cost asphalt was used as both the reduction agent and the carbon source. An Ni-doped spherical LiFePO₄/C composite exhibited better electrochemical performances compared to an un-doped one. It presented an initial discharge capacity of 161 mAhg⁻¹ at 0.1 C rate (the theoretical capacity of LiFePO₄ with 5 wt% carbon is about 161 mAhg⁻¹). After 50 cycles at 0.5 C rate, its capacity remained 137 mAhg⁻¹ (100% of the initial capacity) compared to 115 mAhg⁻¹ (92% of the initial capacity) for an un-doped one. The electrochemical impedance spectroscopy analysis and cyclic voltammograms results revealed that Ni doping could decrease the resistance of LiFePO₄/C composite electrode drastically and improve its reversibility.     

Synthesis, characterization and electrochemical behavior of polypyrrole/carbon nanotube composites using organometallic-functionalized carbon nanotubes

Thorn-like, organometallic-functionalized carbon nanotubes were successfully developed via a novel microwave hydrothermal route. The organometallic complex with methyl orange and iron (III) chloride served as reactive seed template, resulting in the oriented polymerization of pyrrole on the modified carbon nanotubes without the assistance of other oxidants. Morphological and structural characterizations of the carbon nanotube/methyl orange-iron (III) chloride and polypyrrole/carbon nanotube composites were examined using transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), infrared spectroscopy and X-ray diffraction (XRD). The electrochemical property of the polypyrrole/carbon nanotube composite was elucidated by cyclic voltammetry and galvanostatic charge-discharge. A specific capacitance of 304 F g⁻¹ was obtained within the potential range of −0.5-0.5 V in 1 M KCl solution.     

Hydrogen peroxide biosensor based on gold nanoparticles/thionine/gold nanoparticles/multi-walled carbon nanotubes-chitosans composite film-modified electrode

In this paper, an amperometric electrochemical biosensor for the detection of hydrogen peroxide (H₂O₂), based on gold nanoparticles (GNPs)/thionine (Thi)/GNPs/multi-walled carbon nanotubes (MWCNTs)-chitosans (Chits) composite film was developed. MWCNTs-Chits homogeneous composite was first dispersed in acetic acid solution and then the GNPs were in situ synthesized at the composite. The mixture was dripped on the glassy carbon electrode (GCE) and then the Thi was deposited by electropolymerization by Au-S or Au-N covalent bond effect and electrostatic adsorption effect as an electron transfer mediator. Finally, the mixture of GNPs and horseradish peroxidase (HRP) was assembled onto the modified electrode by covalent bond. The electrochemical behavior of the modified electrode was investigated by scanning electron microscope, cyclic voltammetry and chronoamperometry. This study introduces the in situ-synthesized GNPs on the other surface of the modified materials in H₂O₂ detection. The linear response range of the biosensor to H₂O₂ concentration was from 5 × 10⁻⁷ mol L⁻¹ to 1.5 × 10⁻³ mol L⁻¹ with a detection limit of 3.75 × 10⁻⁸ mol L⁻¹ (based on S/N = 3).     

Fabrication of carbon-coated MnOx-Ni foam electrodes via pyrolysis of α-chitosan and their electrochemical performance

Carbon coated MnO_x-Ni foam electrodes were successfully prepared using a combined process of hydrogel reaction followed by high-temperature pyrolysis under air or Ar gas conditions. The prepared samples were analyzed by various characterization tools. To evaluate the performances of the carbon coated MnO_x-Ni foam electrodes as supercapacitors, cyclic voltammetry (CV), galvanostatic charge–discharge, electrochemical impedance spectroscopy (EIS) and cycle stability were also carried out. The carbon coated MnO_x-Ni foam electrodes displayed supercapacitive behavior in 1.0 M KOH with a high specific capacitance value of 354.6 F g⁻¹ at 10 mV s⁻¹. The electrode also exhibited remarkable cycle stability. This research provides a valuable and effective approach to enhance the performance of materials applied as supercapacitors.     

Preparation and electrochemical performance of novel ruthenium-manganese oxide electrode materials for electrochemical capacitors

A series of novel ruthenium-manganese oxide (denoted as Ru_nMn_1−nO_x) has been formed by oxidative co-precipitating. The precursor was obtained by mixing Mn(VII) (potassium permanganate), Mn(II) (manganese acetate) and Ru(III) (ruthenium chloride) in neutral aqueous solution at room temperature. The powder of Ru_nMn_1−nO_x was obtained by calcinating the precursor at appropriate temperature. The crystalline structure and electrochemical performance of the powder have been studied as a function of the calcination temperature. At appropriate calcination temperature (e.g. 170 °C), the powder is in hydrous amorphous phase with a high specific capacitance. When the calcination temperature reaches up to 350 °C, the crystal form of α-MnO₂ is formed, but the ruthenium oxide still keeps amorphous structure, which will lead to the decrease of specific capacitance of the composite electrode materials. The X-ray photoelectron spectroscopy (XPS) analysis shows that the powder of Ru_nMn_1−nO_x prepared in this study belongs to the composite of RuO₂-MnO₂. The results from cyclic voltammetry (CV), chronopotentiometry and electrochemical impedance spectroscopy (EIS) indicate that the ruthenium weight density of 9 wt% in Ru_nMn_1−nO_x can improve the cost-performance of ruthenium-manganese composite electrode.